part2 (3493B)
1--- Part Two --- 2 3The air conditioner comes online! Its cold air feels good for a while, but then the TEST alarms 4start to go off. Since the air conditioner can't vent its heat anywhere but back into the 5spacecraft, it's actually making the air inside the ship [1m[97mwarmer[0m. 6 7Instead, you'll need to use the TEST to extend the thermal radiators. Fortunately, the diagnostic 8program (your puzzle input) is already equipped for this. Unfortunately, your Intcode computer is 9not. 10 11Your computer is only missing a few opcodes: 12 13 14 - Opcode 5 is [1m[97mjump-if-true[0m: if the first parameter is [1m[97mnon-zero[0m, it sets the instruction pointer to 15the value from the second parameter. Otherwise, it does nothing. 16 17 - Opcode 6 is [1m[97mjump-if-false[0m: if the first parameter [1m[97mis zero[0m, it sets the instruction pointer to the 18value from the second parameter. Otherwise, it does nothing. 19 20 - Opcode 7 is [1m[97mless than[0m: if the first parameter is [1m[97mless than[0m the second parameter, it stores 1 in 21the position given by the third parameter. Otherwise, it stores 0. 22 23 - Opcode 8 is [1m[97mequals[0m: if the first parameter is [1m[97mequal to[0m the second parameter, it stores 1 in the 24position given by the third parameter. Otherwise, it stores 0. 25 26 27Like all instructions, these instructions need to support [1m[97mparameter modes[0m as described above. 28 29Normally, after an instruction is finished, the instruction pointer increases by the number of 30values in that instruction. [1m[97mHowever[0m, if the instruction modifies the instruction pointer, that value 31is used and the instruction pointer is [1m[97mnot automatically increased[0m. 32 33For example, here are several programs that take one input, compare it to the value 8, and then 34produce one output: 35 36 37 - 3,9,8,9,10,9,4,9,99,-1,8 - Using [1m[97mposition mode[0m, consider whether the input is [1m[97mequal to[0m 8; output 381 (if it is) or 0 (if it is not). 39 40 - 3,9,7,9,10,9,4,9,99,-1,8 - Using [1m[97mposition mode[0m, consider whether the input is [1m[97mless than[0m 8; output 411 (if it is) or 0 (if it is not). 42 43 - 3,3,1108,-1,8,3,4,3,99 - Using [1m[97mimmediate mode[0m, consider whether the input is [1m[97mequal to[0m 8; output 1 44(if it is) or 0 (if it is not). 45 46 - 3,3,1107,-1,8,3,4,3,99 - Using [1m[97mimmediate mode[0m, consider whether the input is [1m[97mless than [0m8; output 471 (if it is) or 0 (if it is not). 48 49 50Here are some jump tests that take an input, then output 0 if the input was zero or 1 if the input 51was non-zero: 52 53 54 - 3,12,6,12,15,1,13,14,13,4,13,99,-1,0,1,9 (using [1m[97mposition mode[0m) 55 56 - 3,3,1105,-1,9,1101,0,0,12,4,12,99,1 (using [1m[97mimmediate mode[0m) 57 58 59Here's a larger example: 60 613,21,1008,21,8,20,1005,20,22,107,8,21,20,1006,20,31, 621106,0,36,98,0,0,1002,21,125,20,4,20,1105,1,46,104, 63999,1105,1,46,1101,1000,1,20,4,20,1105,1,46,98,99 64 65The above example program uses an input instruction to ask for a single number. The program will 66then output 999 if the input value is below 8, output 1000 if the input value is equal to 8, or 67output 1001 if the input value is greater than 8. 68 69This time, when the TEST diagnostic program runs its input instruction to get the ID of the system 70to test, [1m[97mprovide it 5[0m, the ID for the ship's thermal radiator controller. This diagnostic test suite 71only outputs one number, the [1m[97mdiagnostic code[0m. 72 73[1m[97mWhat is the diagnostic code for system ID 5?[0m 74 75