zinitix,bt400.yaml (3192B)
1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/input/touchscreen/zinitix,bt400.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Zinitix BT4xx and BT5xx series touchscreen controller bindings 8 9description: The Zinitix BT4xx and BT5xx series of touchscreen controllers 10 are Korea-produced touchscreens with embedded microcontrollers. The 11 BT4xx series was produced 2010-2013 and the BT5xx series 2013-2014. 12 13maintainers: 14 - Michael Srba <Michael.Srba@seznam.cz> 15 - Linus Walleij <linus.walleij@linaro.org> 16 17allOf: 18 - $ref: touchscreen.yaml# 19 20properties: 21 $nodename: 22 pattern: "^touchscreen(@.*)?$" 23 24 compatible: 25 enum: 26 - zinitix,bt402 27 - zinitix,bt403 28 - zinitix,bt404 29 - zinitix,bt412 30 - zinitix,bt413 31 - zinitix,bt431 32 - zinitix,bt432 33 - zinitix,bt531 34 - zinitix,bt532 35 - zinitix,bt538 36 - zinitix,bt541 37 - zinitix,bt548 38 - zinitix,bt554 39 - zinitix,at100 40 41 reg: 42 description: I2C address on the I2C bus 43 44 clock-frequency: 45 description: I2C client clock frequency, defined for host when using 46 the device on the I2C bus 47 minimum: 0 48 maximum: 400000 49 50 interrupts: 51 description: Interrupt to host 52 maxItems: 1 53 54 vcca-supply: 55 description: Analog power supply regulator on the VCCA pin 56 57 vdd-supply: 58 description: Digital power supply regulator on the VDD pin. 59 In older device trees this can be the accidental name for the analog 60 supply on the VCCA pin, and in that case the deprecated vddo-supply is 61 used for the digital power supply. 62 63 vddo-supply: 64 description: Deprecated name for the digital power supply, use vdd-supply 65 as this reflects the real name of the pin. If this supply is present, 66 the vdd-supply represents VCCA instead of VDD. Implementers should first 67 check for this property, and if it is present assume that the vdd-supply 68 represents the analog supply. 69 deprecated: true 70 71 reset-gpios: 72 description: Reset line for the touchscreen, should be tagged 73 as GPIO_ACTIVE_LOW 74 75 zinitix,mode: 76 description: Mode of reporting touch points. Some modes may not work 77 with a particular ts firmware for unknown reasons. Available modes are 78 1 and 2. Mode 2 is the default and preferred. 79 $ref: /schemas/types.yaml#/definitions/uint32 80 enum: [1, 2] 81 82 touchscreen-size-x: true 83 touchscreen-size-y: true 84 touchscreen-fuzz-x: true 85 touchscreen-fuzz-y: true 86 87additionalProperties: false 88 89required: 90 - compatible 91 - reg 92 - interrupts 93 - touchscreen-size-x 94 - touchscreen-size-y 95 96examples: 97 - | 98 #include <dt-bindings/interrupt-controller/irq.h> 99 #include <dt-bindings/gpio/gpio.h> 100 i2c { 101 #address-cells = <1>; 102 #size-cells = <0>; 103 104 touchscreen@20 { 105 compatible = "zinitix,bt541"; 106 reg = <0x20>; 107 interrupt-parent = <&gpio>; 108 interrupts = <13 IRQ_TYPE_EDGE_FALLING>; 109 vcca-supply = <®_vcca_tsp>; 110 vdd-supply = <®_vdd_tsp>; 111 touchscreen-size-x = <540>; 112 touchscreen-size-y = <960>; 113 zinitix,mode = <2>; 114 }; 115 };