cachepc-linux

Fork of AMDESE/linux with modifications for CachePC side-channel attack
git clone https://git.sinitax.com/sinitax/cachepc-linux
Log | Files | Refs | README | LICENSE | sfeed.txt

ovti,ov02a10.yaml (4030B)

      1# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
      2# Copyright (c) 2020 MediaTek Inc.
      3%YAML 1.2
      4---
      5$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml#
      6$schema: http://devicetree.org/meta-schemas/core.yaml#
      7
      8title: Omnivision OV02A10 CMOS Sensor Device Tree Bindings
      9
     10maintainers:
     11  - Dongchun Zhu <dongchun.zhu@mediatek.com>
     12
     13description: |-
     14  The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel
     15  image sensor, which is the latest production derived from Omnivision's CMOS
     16  image sensor technology. Ihis chip supports high frame rate speeds up to 30fps
     17  @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The
     18  sensor output is available via CSI-2 serial data output.
     19
     20allOf:
     21  - $ref: /schemas/media/video-interface-devices.yaml#
     22
     23properties:
     24  compatible:
     25    const: ovti,ov02a10
     26
     27  reg:
     28    maxItems: 1
     29
     30  clocks:
     31    maxItems: 1
     32
     33  clock-names:
     34    description:
     35      External clock for the sensor.
     36    items:
     37      - const: eclk
     38
     39  clock-frequency:
     40    description:
     41      Frequency of the eclk clock in Hz.
     42
     43  dovdd-supply:
     44    description:
     45      Definition of the regulator used as Digital I/O voltage supply.
     46
     47  avdd-supply:
     48    description:
     49      Definition of the regulator used as Analog voltage supply.
     50
     51  dvdd-supply:
     52    description:
     53      Definition of the regulator used as Digital core voltage supply.
     54
     55  powerdown-gpios:
     56    description:
     57      Must be the device tree identifier of the GPIO connected to the
     58      PD_PAD pin. This pin is used to place the OV02A10 into standby mode
     59      or shutdown mode. As the line needs to be high for the powerdown mode
     60      to be active, it should be marked GPIO_ACTIVE_HIGH.
     61    maxItems: 1
     62
     63  reset-gpios:
     64    description:
     65      Must be the device tree identifier of the GPIO connected to the
     66      RST_PD pin. If specified, it will be asserted during driver probe.
     67      As the line needs to be low for the reset to be active, it should be
     68      marked GPIO_ACTIVE_LOW.
     69    maxItems: 1
     70
     71  rotation:
     72    enum:
     73      - 0    # Sensor Mounted Upright
     74      - 180  # Sensor Mounted Upside Down
     75    default: 0
     76
     77  port:
     78    $ref: /schemas/graph.yaml#/$defs/port-base
     79    additionalProperties: false
     80    description:
     81      Output port node, single endpoint describing the CSI-2 transmitter.
     82
     83    properties:
     84      endpoint:
     85        $ref: /schemas/media/video-interfaces.yaml#
     86        unevaluatedProperties: false
     87
     88        properties:
     89          link-frequencies: true
     90          ovti,mipi-clock-voltage:
     91            $ref: "/schemas/types.yaml#/definitions/uint32"
     92            description:
     93              Definition of MIPI clock voltage unit. This entry corresponds to
     94              the link speed defined by the 'link-frequencies' property.
     95              If present, the value shall be in the range of 0-4.
     96            default: 4
     97
     98        required:
     99          - link-frequencies
    100
    101    required:
    102      - endpoint
    103
    104required:
    105  - compatible
    106  - reg
    107  - clocks
    108  - clock-names
    109  - clock-frequency
    110  - dovdd-supply
    111  - avdd-supply
    112  - dvdd-supply
    113  - powerdown-gpios
    114  - reset-gpios
    115  - port
    116
    117additionalProperties: false
    118
    119examples:
    120  - |
    121    #include <dt-bindings/gpio/gpio.h>
    122
    123    i2c {
    124        #address-cells = <1>;
    125        #size-cells = <0>;
    126
    127        ov02a10: camera-sensor@3d {
    128            compatible = "ovti,ov02a10";
    129            reg = <0x3d>;
    130
    131            powerdown-gpios = <&pio 107 GPIO_ACTIVE_HIGH>;
    132            reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>;
    133
    134            clocks = <&ov02a10_clk>;
    135            clock-names = "eclk";
    136            clock-frequency = <24000000>;
    137
    138            rotation = <180>;
    139
    140            dovdd-supply = <&ov02a10_dovdd>;
    141            avdd-supply = <&ov02a10_avdd>;
    142            dvdd-supply = <&ov02a10_dvdd>;
    143
    144            port {
    145                wcam_out: endpoint {
    146                    link-frequencies = /bits/ 64 <390000000>;
    147                    ovti,mipi-clock-voltage = <3>;
    148                    remote-endpoint = <&mipi_in_wcam>;
    149                };
    150            };
    151        };
    152    };
    153
    154...