sdhci-st.txt (3680B)
1* STMicroelectronics sdhci-st MMC/SD controller 2 3This file documents the differences between the core properties in 4Documentation/devicetree/bindings/mmc/mmc.txt and the properties 5used by the sdhci-st driver. 6 7Required properties: 8- compatible: Must be "st,sdhci" and it can be compatible to "st,sdhci-stih407" 9 to set the internal glue logic used for configuring the MMC 10 subsystem (mmcss) inside the FlashSS (available in STiH407 SoC 11 family). 12 13- clock-names: Should be "mmc" and "icn". (NB: The latter is not compulsory) 14 See: Documentation/devicetree/bindings/resource-names.txt 15- clocks: Phandle to the clock. 16 See: Documentation/devicetree/bindings/clock/clock-bindings.txt 17 18- interrupts: One mmc interrupt should be described here. 19- interrupt-names: Should be "mmcirq". 20 21- pinctrl-names: A pinctrl state names "default" must be defined. 22- pinctrl-0: Phandle referencing pin configuration of the sd/emmc controller. 23 See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt 24 25- reg: This must provide the host controller base address and it can also 26 contain the FlashSS Top register for TX/RX delay used by the driver 27 to configure DLL inside the flashSS, if so reg-names must also be 28 specified. 29 30Optional properties: 31- reg-names: Should be "mmc" and "top-mmc-delay". "top-mmc-delay" is optional 32 for eMMC on stih407 family silicon to configure DLL inside FlashSS. 33 34- non-removable: Non-removable slot. Also used for configuring mmcss in STiH407 SoC 35 family. 36 See: Documentation/devicetree/bindings/mmc/mmc.txt. 37 38- bus-width: Number of data lines. 39 See: Documentation/devicetree/bindings/mmc/mmc.txt. 40 41- max-frequency: Can be 200MHz, 100MHz or 50MHz (default) and used for 42 configuring the CCONFIG3 in the mmcss. 43 See: Documentation/devicetree/bindings/mmc/mmc.txt. 44 45- resets: Phandle and reset specifier pair to softreset line of HC IP. 46 See: Documentation/devicetree/bindings/reset/reset.txt 47 48- vqmmc-supply: Phandle to the regulator dt node, mentioned as the vcc/vdd 49 supply in eMMC/SD specs. 50 51- sd-uhs-sdr50: To enable the SDR50 in the mmcss. 52 See: Documentation/devicetree/bindings/mmc/mmc.txt. 53 54- sd-uhs-sdr104: To enable the SDR104 in the mmcss. 55 See: Documentation/devicetree/bindings/mmc/mmc.txt. 56 57- sd-uhs-ddr50: To enable the DDR50 in the mmcss. 58 See: Documentation/devicetree/bindings/mmc/mmc.txt. 59 60Example: 61 62/* Example stih416e eMMC configuration */ 63 64mmc0: sdhci@fe81e000 { 65 compatible = "st,sdhci"; 66 reg = <0xfe81e000 0x1000>; 67 interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>; 68 interrupt-names = "mmcirq"; 69 pinctrl-names = "default"; 70 pinctrl-0 = <&pinctrl_mmc0>; 71 clock-names = "mmc"; 72 clocks = <&clk_s_a1_ls 1>; 73 bus-width = <8> 74 75/* Example SD stih407 family configuration */ 76 77mmc1: sdhci@9080000 { 78 compatible = "st,sdhci-stih407", "st,sdhci"; 79 reg = <0x09080000 0x7ff>; 80 reg-names = "mmc"; 81 interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>; 82 interrupt-names = "mmcirq"; 83 pinctrl-names = "default"; 84 pinctrl-0 = <&pinctrl_sd1>; 85 clock-names = "mmc"; 86 clocks = <&clk_s_c0_flexgen CLK_MMC_1>; 87 resets = <&softreset STIH407_MMC1_SOFTRESET>; 88 bus-width = <4>; 89}; 90 91/* Example eMMC stih407 family configuration */ 92 93mmc0: sdhci@9060000 { 94 compatible = "st,sdhci-stih407", "st,sdhci"; 95 reg = <0x09060000 0x7ff>, <0x9061008 0x20>; 96 reg-names = "mmc", "top-mmc-delay"; 97 interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>; 98 interrupt-names = "mmcirq"; 99 pinctrl-names = "default"; 100 pinctrl-0 = <&pinctrl_mmc0>; 101 clock-names = "mmc"; 102 clocks = <&clk_s_c0_flexgen CLK_MMC_0>; 103 vqmmc-supply = <&vmmc_reg>; 104 max-frequency = <200000000>; 105 bus-width = <8>; 106 non-removable; 107 sd-uhs-sdr50; 108 sd-uhs-sdr104; 109 sd-uhs-ddr50; 110};