amd-xgbe.txt (2967B)
1* AMD 10GbE driver (amd-xgbe) 2 3Required properties: 4- compatible: Should be "amd,xgbe-seattle-v1a" 5- reg: Address and length of the register sets for the device 6 - MAC registers 7 - PCS registers 8 - SerDes Rx/Tx registers 9 - SerDes integration registers (1/2) 10 - SerDes integration registers (2/2) 11- interrupts: Should contain the amd-xgbe interrupt(s). The first interrupt 12 listed is required and is the general device interrupt. If the optional 13 amd,per-channel-interrupt property is specified, then one additional 14 interrupt for each DMA channel supported by the device should be specified. 15 The last interrupt listed should be the PCS auto-negotiation interrupt. 16- clocks: 17 - DMA clock for the amd-xgbe device (used for calculating the 18 correct Rx interrupt watchdog timer value on a DMA channel 19 for coalescing) 20 - PTP clock for the amd-xgbe device 21- clock-names: Should be the names of the clocks 22 - "dma_clk" for the DMA clock 23 - "ptp_clk" for the PTP clock 24- phy-mode: See ethernet.txt file in the same directory 25 26Optional properties: 27- dma-coherent: Present if dma operations are coherent 28- amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate 29 a unique interrupt for each DMA channel - this requires an additional 30 interrupt be configured for each DMA channel 31- amd,speed-set: Speed capabilities of the device 32 0 - 1GbE and 10GbE (default) 33 1 - 2.5GbE and 10GbE 34 35The MAC address will be determined using the optional properties defined in 36ethernet.txt. 37 38The following optional properties are represented by an array with each 39value corresponding to a particular speed. The first array value represents 40the setting for the 1GbE speed, the second value for the 2.5GbE speed and 41the third value for the 10GbE speed. All three values are required if the 42property is used. 43- amd,serdes-blwc: Baseline wandering correction enablement 44 0 - Off 45 1 - On 46- amd,serdes-cdr-rate: CDR rate speed selection 47- amd,serdes-pq-skew: PQ (data sampling) skew 48- amd,serdes-tx-amp: TX amplitude boost 49- amd,serdes-dfe-tap-config: DFE taps available to run 50- amd,serdes-dfe-tap-enable: DFE taps to enable 51 52Example: 53 xgbe@e0700000 { 54 compatible = "amd,xgbe-seattle-v1a"; 55 reg = <0 0xe0700000 0 0x80000>, 56 <0 0xe0780000 0 0x80000>, 57 <0 0xe1240800 0 0x00400>, 58 <0 0xe1250000 0 0x00060>, 59 <0 0xe1250080 0 0x00004>; 60 interrupt-parent = <&gic>; 61 interrupts = <0 325 4>, 62 <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>, 63 <0 323 4>; 64 amd,per-channel-interrupt; 65 clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>; 66 clock-names = "dma_clk", "ptp_clk"; 67 phy-mode = "xgmii"; 68 mac-address = [ 02 a1 a2 a3 a4 a5 ]; 69 amd,speed-set = <0>; 70 amd,serdes-blwc = <1>, <1>, <0>; 71 amd,serdes-cdr-rate = <2>, <2>, <7>; 72 amd,serdes-pq-skew = <10>, <10>, <30>; 73 amd,serdes-tx-amp = <15>, <15>, <10>; 74 amd,serdes-dfe-tap-config = <3>, <3>, <1>; 75 amd,serdes-dfe-tap-enable = <0>, <0>, <127>; 76 };