cachepc-linux

Fork of AMDESE/linux with modifications for CachePC side-channel attack
git clone https://git.sinitax.com/sinitax/cachepc-linux
Log | Files | Refs | README | LICENSE | sfeed.txt

broadcom-bluetooth.yaml (3433B)

      1# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
      2%YAML 1.2
      3---
      4$id: http://devicetree.org/schemas/net/broadcom-bluetooth.yaml#
      5$schema: http://devicetree.org/meta-schemas/core.yaml#
      6
      7title: Broadcom Bluetooth Chips
      8
      9maintainers:
     10  - Linus Walleij <linus.walleij@linaro.org>
     11
     12description:
     13  This binding describes Broadcom UART-attached bluetooth chips.
     14
     15properties:
     16  compatible:
     17    enum:
     18      - brcm,bcm20702a1
     19      - brcm,bcm4329-bt
     20      - brcm,bcm4330-bt
     21      - brcm,bcm4334-bt
     22      - brcm,bcm43438-bt
     23      - brcm,bcm4345c5
     24      - brcm,bcm43540-bt
     25      - brcm,bcm4335a0
     26
     27  shutdown-gpios:
     28    maxItems: 1
     29    description: GPIO specifier for the line BT_REG_ON used to
     30      power on the BT module
     31
     32  reset-gpios:
     33    maxItems: 1
     34    description: GPIO specifier for the line BT_RST_N used to
     35      reset the BT module. This should be marked as
     36      GPIO_ACTIVE_LOW.
     37
     38  device-wakeup-gpios:
     39    maxItems: 1
     40    description: GPIO specifier for the line BT_WAKE used to
     41      wakeup the controller. This is using the BT_GPIO_0
     42      pin on the chip when in use.
     43
     44  host-wakeup-gpios:
     45    maxItems: 1
     46    deprecated: true
     47    description: GPIO specifier for the line HOST_WAKE used
     48      to wakeup the host processor. This is using he BT_GPIO_1
     49      pin on the chip when in use. This is deprecated and replaced
     50      by interrupts and "host-wakeup" interrupt-names
     51
     52  clocks:
     53    minItems: 1
     54    maxItems: 2
     55    description: 1 or 2 clocks as defined in clock-names below,
     56      in that order
     57
     58  clock-names:
     59    description: Names of the 1 to 2 supplied clocks
     60    oneOf:
     61      - const: extclk
     62        deprecated: true
     63        description: Deprecated in favor of txco
     64
     65      - const: txco
     66        description: >
     67          external reference clock (not a standalone crystal)
     68
     69      - const: lpo
     70        description: >
     71          external low power 32.768 kHz clock
     72
     73      - items:
     74          - const: txco
     75          - const: lpo
     76
     77  vbat-supply:
     78    description: phandle to regulator supply for VBAT
     79
     80  vddio-supply:
     81    description: phandle to regulator supply for VDDIO
     82
     83  brcm,bt-pcm-int-params:
     84    $ref: /schemas/types.yaml#/definitions/uint8-array
     85    minItems: 5
     86    maxItems: 5
     87    description: |-
     88      configure PCM parameters via a 5-byte array:
     89       sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S
     90       pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps
     91       pcm-frame-type: short, long
     92       pcm-sync-mode: slave, master
     93       pcm-clock-mode: slave, master
     94
     95  interrupts:
     96    items:
     97      - description: Handle to the line HOST_WAKE used to wake
     98          up the host processor. This uses the BT_GPIO_1 pin on
     99          the chip when in use.
    100
    101  interrupt-names:
    102    items:
    103      - const: host-wakeup
    104
    105  max-speed: true
    106  current-speed: true
    107
    108required:
    109  - compatible
    110
    111additionalProperties: false
    112
    113examples:
    114  - |
    115    #include <dt-bindings/gpio/gpio.h>
    116    #include <dt-bindings/interrupt-controller/irq.h>
    117
    118    uart {
    119        uart-has-rtscts;
    120
    121        bluetooth {
    122            compatible = "brcm,bcm4330-bt";
    123            max-speed = <921600>;
    124            brcm,bt-pcm-int-params = [01 02 00 01 01];
    125            shutdown-gpios = <&gpio 30 GPIO_ACTIVE_HIGH>;
    126            device-wakeup-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
    127            reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
    128            interrupt-parent = <&gpio>;
    129            interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
    130        };
    131    };