qca8k.yaml (9029B)
1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/net/dsa/qca8k.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Qualcomm Atheros QCA83xx switch family 8 9maintainers: 10 - John Crispin <john@phrozen.org> 11 12description: 13 If the QCA8K switch is connect to an SoC's external mdio-bus, each subnode 14 describing a port needs to have a valid phandle referencing the internal PHY 15 it is connected to. This is because there is no N:N mapping of port and PHY 16 ID. To declare the internal mdio-bus configuration, declare an MDIO node in 17 the switch node and declare the phandle for the port, referencing the internal 18 PHY it is connected to. In this config, an internal mdio-bus is registered and 19 the MDIO master is used for communication. Mixed external and internal 20 mdio-bus configurations are not supported by the hardware. 21 22properties: 23 compatible: 24 oneOf: 25 - enum: 26 - qca,qca8327 27 - qca,qca8328 28 - qca,qca8334 29 - qca,qca8337 30 description: | 31 qca,qca8328: referenced as AR8328(N)-AK1(A/B) QFN 176 pin package 32 qca,qca8327: referenced as AR8327(N)-AL1A DR-QFN 148 pin package 33 qca,qca8334: referenced as QCA8334-AL3C QFN 88 pin package 34 qca,qca8337: referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package 35 36 reg: 37 maxItems: 1 38 39 reset-gpios: 40 description: 41 GPIO to be used to reset the whole device 42 maxItems: 1 43 44 qca,ignore-power-on-sel: 45 $ref: /schemas/types.yaml#/definitions/flag 46 description: 47 Ignore power-on pin strapping to configure LED open-drain or EEPROM 48 presence. This is needed for devices with incorrect configuration or when 49 the OEM has decided not to use pin strapping and falls back to SW regs. 50 51 qca,led-open-drain: 52 $ref: /schemas/types.yaml#/definitions/flag 53 description: 54 Set LEDs to open-drain mode. This requires the qca,ignore-power-on-sel to 55 be set, otherwise the driver will fail at probe. This is required if the 56 OEM does not use pin strapping to set this mode and prefers to set it 57 using SW regs. The pin strappings related to LED open-drain mode are 58 B68 on the QCA832x and B49 on the QCA833x. 59 60 mdio: 61 $ref: /schemas/net/mdio.yaml# 62 unevaluatedProperties: false 63 description: Qca8k switch have an internal mdio to access switch port. 64 If this is not present, the legacy mapping is used and the 65 internal mdio access is used. 66 With the legacy mapping the reg corresponding to the internal 67 mdio is the switch reg with an offset of -1. 68 69patternProperties: 70 "^(ethernet-)?ports$": 71 type: object 72 properties: 73 '#address-cells': 74 const: 1 75 '#size-cells': 76 const: 0 77 78 patternProperties: 79 "^(ethernet-)?port@[0-6]$": 80 type: object 81 description: Ethernet switch ports 82 83 $ref: dsa-port.yaml# 84 85 properties: 86 qca,sgmii-rxclk-falling-edge: 87 $ref: /schemas/types.yaml#/definitions/flag 88 description: 89 Set the receive clock phase to falling edge. Mostly commonly used on 90 the QCA8327 with CPU port 0 set to SGMII. 91 92 qca,sgmii-txclk-falling-edge: 93 $ref: /schemas/types.yaml#/definitions/flag 94 description: 95 Set the transmit clock phase to falling edge. 96 97 qca,sgmii-enable-pll: 98 $ref: /schemas/types.yaml#/definitions/flag 99 description: 100 For SGMII CPU port, explicitly enable PLL, TX and RX chain along with 101 Signal Detection. On the QCA8327 this should not be enabled, otherwise 102 the SGMII port will not initialize. When used on the QCA8337, revision 3 103 or greater, a warning will be displayed. When the CPU port is set to 104 SGMII on the QCA8337, it is advised to set this unless a communication 105 issue is observed. 106 107 unevaluatedProperties: false 108 109oneOf: 110 - required: 111 - ports 112 - required: 113 - ethernet-ports 114 115required: 116 - compatible 117 - reg 118 119additionalProperties: true 120 121examples: 122 - | 123 #include <dt-bindings/gpio/gpio.h> 124 125 mdio { 126 #address-cells = <1>; 127 #size-cells = <0>; 128 129 external_phy_port1: ethernet-phy@0 { 130 reg = <0>; 131 }; 132 133 external_phy_port2: ethernet-phy@1 { 134 reg = <1>; 135 }; 136 137 external_phy_port3: ethernet-phy@2 { 138 reg = <2>; 139 }; 140 141 external_phy_port4: ethernet-phy@3 { 142 reg = <3>; 143 }; 144 145 external_phy_port5: ethernet-phy@4 { 146 reg = <4>; 147 }; 148 149 switch@10 { 150 compatible = "qca,qca8337"; 151 #address-cells = <1>; 152 #size-cells = <0>; 153 reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; 154 reg = <0x10>; 155 156 ports { 157 #address-cells = <1>; 158 #size-cells = <0>; 159 160 port@0 { 161 reg = <0>; 162 label = "cpu"; 163 ethernet = <&gmac1>; 164 phy-mode = "rgmii"; 165 166 fixed-link { 167 speed = <1000>; 168 full-duplex; 169 }; 170 }; 171 172 port@1 { 173 reg = <1>; 174 label = "lan1"; 175 phy-handle = <&external_phy_port1>; 176 }; 177 178 port@2 { 179 reg = <2>; 180 label = "lan2"; 181 phy-handle = <&external_phy_port2>; 182 }; 183 184 port@3 { 185 reg = <3>; 186 label = "lan3"; 187 phy-handle = <&external_phy_port3>; 188 }; 189 190 port@4 { 191 reg = <4>; 192 label = "lan4"; 193 phy-handle = <&external_phy_port4>; 194 }; 195 196 port@5 { 197 reg = <5>; 198 label = "wan"; 199 phy-handle = <&external_phy_port5>; 200 }; 201 }; 202 }; 203 }; 204 - | 205 #include <dt-bindings/gpio/gpio.h> 206 207 mdio { 208 #address-cells = <1>; 209 #size-cells = <0>; 210 211 switch@10 { 212 compatible = "qca,qca8337"; 213 #address-cells = <1>; 214 #size-cells = <0>; 215 reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; 216 reg = <0x10>; 217 218 ports { 219 #address-cells = <1>; 220 #size-cells = <0>; 221 222 port@0 { 223 reg = <0>; 224 label = "cpu"; 225 ethernet = <&gmac1>; 226 phy-mode = "rgmii"; 227 228 fixed-link { 229 speed = <1000>; 230 full-duplex; 231 }; 232 }; 233 234 port@1 { 235 reg = <1>; 236 label = "lan1"; 237 phy-mode = "internal"; 238 phy-handle = <&internal_phy_port1>; 239 }; 240 241 port@2 { 242 reg = <2>; 243 label = "lan2"; 244 phy-mode = "internal"; 245 phy-handle = <&internal_phy_port2>; 246 }; 247 248 port@3 { 249 reg = <3>; 250 label = "lan3"; 251 phy-mode = "internal"; 252 phy-handle = <&internal_phy_port3>; 253 }; 254 255 port@4 { 256 reg = <4>; 257 label = "lan4"; 258 phy-mode = "internal"; 259 phy-handle = <&internal_phy_port4>; 260 }; 261 262 port@5 { 263 reg = <5>; 264 label = "wan"; 265 phy-mode = "internal"; 266 phy-handle = <&internal_phy_port5>; 267 }; 268 269 port@6 { 270 reg = <0>; 271 label = "cpu"; 272 ethernet = <&gmac1>; 273 phy-mode = "sgmii"; 274 275 qca,sgmii-rxclk-falling-edge; 276 277 fixed-link { 278 speed = <1000>; 279 full-duplex; 280 }; 281 }; 282 }; 283 284 mdio { 285 #address-cells = <1>; 286 #size-cells = <0>; 287 288 internal_phy_port1: ethernet-phy@0 { 289 reg = <0>; 290 }; 291 292 internal_phy_port2: ethernet-phy@1 { 293 reg = <1>; 294 }; 295 296 internal_phy_port3: ethernet-phy@2 { 297 reg = <2>; 298 }; 299 300 internal_phy_port4: ethernet-phy@3 { 301 reg = <3>; 302 }; 303 304 internal_phy_port5: ethernet-phy@4 { 305 reg = <4>; 306 }; 307 }; 308 }; 309 };