phy-miphy28lp.txt (3754B)
1STMicroelectronics STi MIPHY28LP PHY binding 2============================================ 3 4This binding describes a miphy device that is used to control PHY hardware 5for SATA, PCIe or USB3. 6 7Required properties (controller (parent) node): 8- compatible : Should be "st,miphy28lp-phy". 9- st,syscfg : Should be a phandle of the system configuration register group 10 which contain the SATA, PCIe or USB3 mode setting bits. 11 12Required nodes : A sub-node is required for each channel the controller 13 provides. Address range information including the usual 14 'reg' and 'reg-names' properties are used inside these 15 nodes to describe the controller's topology. These nodes 16 are translated by the driver's .xlate() function. 17 18Required properties (port (child) node): 19- #phy-cells : Should be 1 (See second example) 20 Cell after port phandle is device type from: 21 - PHY_TYPE_SATA 22 - PHY_TYPE_PCI 23 - PHY_TYPE_USB3 24- reg : Address and length of the register set for the device. 25- reg-names : The names of the register addresses corresponding to the registers 26 filled in "reg". It can also contain the offset of the system configuration 27 registers used as glue-logic to setup the device for SATA/PCIe or USB3 28 devices. 29- st,syscfg : Offset of the parent configuration register. 30- resets : phandle to the parent reset controller. 31- reset-names : Associated name must be "miphy-sw-rst". 32 33Optional properties (port (child) node): 34- st,osc-rdy : to check the MIPHY0_OSC_RDY status in the glue-logic. This 35 is not available in all the MiPHY. For example, for STiH407, only the 36 MiPHY0 has this bit. 37- st,osc-force-ext : to select the external oscillator. This can change from 38 different MiPHY inside the same SoC. 39- st,sata_gen : to select which SATA_SPDMODE has to be set in the SATA system config 40 register. 41- st,px_rx_pol_inv : to invert polarity of RXn/RXp (respectively negative line and positive 42 line). 43- st,scc-on : enable ssc to reduce effects of EMI (only for sata or PCIe). 44- st,tx-impedance-comp : to compensate tx impedance avoiding out of range values. 45 46example: 47 48 miphy28lp_phy: miphy28lp@9b22000 { 49 compatible = "st,miphy28lp-phy"; 50 st,syscfg = <&syscfg_core>; 51 #address-cells = <1>; 52 #size-cells = <1>; 53 ranges; 54 55 phy_port0: port@9b22000 { 56 reg = <0x9b22000 0xff>, 57 <0x9b09000 0xff>, 58 <0x9b04000 0xff>; 59 reg-names = "sata-up", 60 "pcie-up", 61 "pipew"; 62 63 st,syscfg = <0x114 0x818 0xe0 0xec>; 64 #phy-cells = <1>; 65 st,osc-rdy; 66 reset-names = "miphy-sw-rst"; 67 resets = <&softreset STIH407_MIPHY0_SOFTRESET>; 68 }; 69 70 phy_port1: port@9b2a000 { 71 reg = <0x9b2a000 0xff>, 72 <0x9b19000 0xff>, 73 <0x9b14000 0xff>; 74 reg-names = "sata-up", 75 "pcie-up", 76 "pipew"; 77 78 st,syscfg = <0x118 0x81c 0xe4 0xf0>; 79 80 #phy-cells = <1>; 81 st,osc-force-ext; 82 reset-names = "miphy-sw-rst"; 83 resets = <&softreset STIH407_MIPHY1_SOFTRESET>; 84 }; 85 86 phy_port2: port@8f95000 { 87 reg = <0x8f95000 0xff>, 88 <0x8f90000 0xff>; 89 reg-names = "pipew", 90 "usb3-up"; 91 92 st,syscfg = <0x11c 0x820>; 93 94 #phy-cells = <1>; 95 reset-names = "miphy-sw-rst"; 96 resets = <&softreset STIH407_MIPHY2_SOFTRESET>; 97 }; 98 }; 99 100 101Specifying phy control of devices 102================================= 103 104Device nodes should specify the configuration required in their "phys" 105property, containing a phandle to the miphy device node and an index 106specifying which configuration to use, as described in phy-bindings.txt. 107 108example: 109 sata0: sata@9b20000 { 110 ... 111 phys = <&phy_port0 PHY_TYPE_SATA>; 112 ... 113 }; 114 115Macro definitions for the supported miphy configuration can be found in: 116 117include/dt-bindings/phy/phy.h