actions,s700-pinctrl.txt (7643B)
1Actions Semi S700 Pin Controller 2 3This binding describes the pin controller found in the S700 SoC. 4 5Required Properties: 6 7- compatible: Should be "actions,s700-pinctrl" 8- reg: Should contain the register base address and size of 9 the pin controller. 10- clocks: phandle of the clock feeding the pin controller 11- gpio-controller: Marks the device node as a GPIO controller. 12- gpio-ranges: Specifies the mapping between gpio controller and 13 pin-controller pins. 14- #gpio-cells: Should be two. The first cell is the gpio pin number 15 and the second cell is used for optional parameters. 16- interrupt-controller: Marks the device node as an interrupt controller. 17- #interrupt-cells: Specifies the number of cells needed to encode an 18 interrupt. Shall be set to 2. The first cell 19 defines the interrupt number, the second encodes 20 the trigger flags described in 21 bindings/interrupt-controller/interrupts.txt 22- interrupts: The interrupt outputs from the controller. There is one GPIO 23 interrupt per GPIO bank. The number of interrupts listed depends 24 on the number of GPIO banks on the SoC. The interrupts must be 25 ordered by bank, starting with bank 0. 26 27Please refer to pinctrl-bindings.txt in this directory for details of the 28common pinctrl bindings used by client devices, including the meaning of the 29phrase "pin configuration node". 30 31The pin configuration nodes act as a container for an arbitrary number of 32subnodes. Each of these subnodes represents some desired configuration for a 33pin, a group, or a list of pins or groups. This configuration can include the 34mux function to select on those group(s), and various pin configuration 35parameters, such as pull-up, drive strength, etc. 36 37PIN CONFIGURATION NODES: 38 39The name of each subnode is not important; all subnodes should be enumerated 40and processed purely based on their content. 41 42Each subnode only affects those parameters that are explicitly listed. In 43other words, a subnode that lists a mux function but no pin configuration 44parameters implies no information about any pin configuration parameters. 45Similarly, a pin subnode that describes a pullup parameter implies no 46information about e.g. the mux function. 47 48Pinmux functions are available only for the pin groups while pinconf 49parameters are available for both pin groups and individual pins. 50 51The following generic properties as defined in pinctrl-bindings.txt are valid 52to specify in a pin configuration subnode: 53 54Required Properties: 55 56- pins: An array of strings, each string containing the name of a pin. 57 These pins are used for selecting the pull control and schmitt 58 trigger parameters. The following are the list of pins 59 available: 60 61 eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer, 62 eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk, 63 eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, 64 i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1, 65 pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2, 66 ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp, 67 lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap, 68 lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp, 69 lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, 70 lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, 71 dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, 72 sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, 73 sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx, 74 uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx, 75 uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk, 76 i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1, 77 csi_cn, csi_cp, csi_dn2, csi_dp2, csi_dn3, csi_dp3, 78 sensor0_pclk, sensor0_ckout, dnand_d0, dnand_d1, dnand_d2, 79 dnand_d3, dnand_d4, dnand_d5, dnand_d6, dnand_d7, dnand_wrb, 80 dnand_rdb, dnand_rdbn, dnand_dqs, dnand_dqsn, dnand_rb0, 81 dnand_ale, dnand_cle, dnand_ceb0, dnand_ceb1, dnand_ceb2, 82 dnand_ceb3, porb, clko_25m, bsel, pkg0, pkg1, pkg2, pkg3 83 84- groups: An array of strings, each string containing the name of a pin 85 group. These pin groups are used for selecting the pinmux 86 functions. 87 rgmii_txd23_mfp, rgmii_rxd2_mfp, rgmii_rxd3_mfp, lcd0_d18_mfp, 88 rgmii_txd01_mfp, rgmii_txd0_mfp, rgmii_txd1_mfp, rgmii_txen_mfp, 89 rgmii_rxen_mfp, rgmii_rxd1_mfp, rgmii_rxd0_mfp, rgmii_ref_clk_mfp, 90 i2s_d0_mfp, i2s_pcm1_mfp, i2s0_pcm0_mfp, i2s1_pcm0_mfp, 91 i2s_d1_mfp, ks_in2_mfp, ks_in1_mfp, ks_in0_mfp, ks_in3_mfp, 92 ks_out0_mfp, ks_out1_mfp, ks_out2_mfp, lvds_o_pn_mfp, dsi_dn0_mfp, 93 dsi_dp2_mfp, lcd0_d2_mfp, dsi_dp3_mfp, dsi_dn3_mfp, dsi_dp0_mfp, 94 lvds_ee_pn_mfp, uart2_rx_tx_mfp, spi0_i2c_pcm_mfp, dsi_dnp1_cp_d2_mfp, 95 dsi_dnp1_cp_d17_mfp, lvds_e_pn_mfp, dsi_dn2_mfp, uart2_rtsb_mfp, 96 uart2_ctsb_mfp, uart3_rtsb_mfp, uart3_ctsb_mfp, sd0_d0_mfp, sd0_d1_mfp, 97 sd0_d2_d3_mfp, sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp, sd1_cmd_mfp, 98 uart0_rx_mfp, clko_25m_mfp, csi_cn_cp_mfp, sens0_ckout_mfp, uart0_tx_mfp, 99 i2c0_mfp, csi_dn_dp_mfp, sen0_pclk_mfp, pcm1_in_mfp, pcm1_clk_mfp, 100 pcm1_sync_mfp, pcm1_out_mfp, dnand_data_wr_mfp, dnand_acle_ce0_mfp, 101 nand_ceb2_mfp, nand_ceb3_mfp 102 103 These pin groups are used for selecting the drive strength 104 parameters. 105 106 sirq_drv, rgmii_txd23_drv, rgmii_rxd23_drv, rgmii_txd01_txen_drv, 107 rgmii_rxer_drv, rgmii_crs_drv, rgmii_rxd10_drv, rgmii_ref_clk_drv, 108 smi_mdc_mdio_drv, i2s_d0_drv, i2s_bclk0_drv, i2s3_drv, i2s13_drv, 109 pcm1_drv, ks_in_drv, ks_out_drv, lvds_all_drv, lcd_d18_d2_drv, 110 dsi_all_drv, sd0_d0_d3_drv, sd0_cmd_drv, sd0_clk_drv, spi0_all_drv, 111 uart0_rx_drv, uart0_tx_drv, uart2_all_drv, i2c0_all_drv, i2c12_all_drv, 112 sens0_pclk_drv, sens0_ckout_drv, uart3_all_drv 113 114- function: An array of strings, each string containing the name of the 115 pinmux functions. These functions can only be selected by 116 the corresponding pin groups. The following are the list of 117 pinmux functions available: 118 119 nor, eth_rgmii, eth_sgmii, spi0, spi1, spi2, spi3, seNs0, sens1, 120 uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, i2s1, 121 pcm1, pcm0, ks, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, p0, 122 sd0, sd1, sd2, i2c0, i2c1, i2c2, i2c3, dsi, lvds, usb30, 123 clko_25m, mipi_csi, nand, spdif, sirq0, sirq1, sirq2, bt, lcd0 124 125Optional Properties: 126 127- bias-pull-down: No arguments. The specified pins should be configured as 128 pull down. 129- bias-pull-up: No arguments. The specified pins should be configured as 130 pull up. 131- input-schmitt-enable: No arguments: Enable schmitt trigger for the specified 132 pins 133- input-schmitt-disable: No arguments: Disable schmitt trigger for the specified 134 pins 135- drive-strength: Integer. Selects the drive strength for the specified 136 pins in mA. 137 Valid values are: 138 <2> 139 <4> 140 <8> 141 <12> 142 143Example: 144 145 pinctrl: pinctrl@e01b0000 { 146 compatible = "actions,s700-pinctrl"; 147 reg = <0x0 0xe01b0000 0x0 0x1000>; 148 clocks = <&cmu CLK_GPIO>; 149 gpio-controller; 150 gpio-ranges = <&pinctrl 0 0 136>; 151 #gpio-cells = <2>; 152 interrupt-controller; 153 #interrupt-cells = <2>; 154 interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, 155 <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, 156 <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, 157 <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, 158 <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; 159 160 uart3-default: uart3-default { 161 pinmux { 162 groups = "uart3_rtsb_mfp", "uart3_ctsb_mfp"; 163 function = "uart3"; 164 }; 165 pinconf { 166 groups = "uart3_all_drv"; 167 drive-strength = <2>; 168 }; 169 }; 170 };