mediatek,mt8183-pinctrl.yaml (7489B)
1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8183-pinctrl.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Mediatek MT8183 Pin Controller Device Tree Bindings 8 9maintainers: 10 - Sean Wang <sean.wang@kernel.org> 11 12description: |+ 13 The MediaTek's MT8183 Pin controller is used to control SoC pins. 14 15properties: 16 compatible: 17 const: mediatek,mt8183-pinctrl 18 19 reg: 20 minItems: 10 21 maxItems: 10 22 23 reg-names: 24 items: 25 - const: iocfg0 26 - const: iocfg1 27 - const: iocfg2 28 - const: iocfg3 29 - const: iocfg4 30 - const: iocfg5 31 - const: iocfg6 32 - const: iocfg7 33 - const: iocfg8 34 - const: eint 35 36 gpio-controller: true 37 38 "#gpio-cells": 39 const: 2 40 description: | 41 Number of cells in GPIO specifier. Since the generic GPIO 42 binding is used, the amount of cells must be specified as 2. See the below 43 mentioned gpio binding representation for description of particular cells. 44 45 gpio-ranges: 46 minItems: 1 47 maxItems: 5 48 description: | 49 GPIO valid number range. 50 51 interrupt-controller: true 52 53 interrupts: 54 maxItems: 1 55 56 "#interrupt-cells": 57 const: 2 58 59allOf: 60 - $ref: "pinctrl.yaml#" 61 62required: 63 - compatible 64 - reg 65 - gpio-controller 66 - "#gpio-cells" 67 - gpio-ranges 68 69patternProperties: 70 '-[0-9]+$': 71 type: object 72 additionalProperties: false 73 patternProperties: 74 'pins': 75 type: object 76 additionalProperties: false 77 description: | 78 A pinctrl node should contain at least one subnodes representing the 79 pinctrl groups available on the machine. Each subnode will list the 80 pins it needs, and how they should be configured, with regard to muxer 81 configuration, pullups, drive strength, input enable/disable and input 82 schmitt. 83 $ref: "/schemas/pinctrl/pincfg-node.yaml" 84 85 properties: 86 pinmux: 87 description: 88 integer array, represents gpio pin number and mux setting. 89 Supported pin number and mux varies for different SoCs, and are 90 defined as macros in <soc>-pinfunc.h directly. 91 92 bias-disable: true 93 94 bias-pull-up: true 95 96 bias-pull-down: true 97 98 input-enable: true 99 100 input-disable: true 101 102 output-low: true 103 104 output-high: true 105 106 input-schmitt-enable: true 107 108 input-schmitt-disable: true 109 110 drive-strength: 111 enum: [2, 4, 6, 8, 10, 12, 14, 16] 112 113 mediatek,drive-strength-adv: 114 description: | 115 Describe the specific driving setup property. 116 For I2C pins, the existing generic driving setup can only support 117 2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they 118 can support 0.125/0.25/0.5/1mA adjustment. If we enable specific 119 driving setup, the existing generic setup will be disabled. 120 The specific driving setup is controlled by E1E0EN. 121 When E1=0/E0=0, the strength is 0.125mA. 122 When E1=0/E0=1, the strength is 0.25mA. 123 When E1=1/E0=0, the strength is 0.5mA. 124 When E1=1/E0=1, the strength is 1mA. 125 EN is used to enable or disable the specific driving setup. 126 Valid arguments are described as below: 127 0: (E1, E0, EN) = (0, 0, 0) 128 1: (E1, E0, EN) = (0, 0, 1) 129 2: (E1, E0, EN) = (0, 1, 0) 130 3: (E1, E0, EN) = (0, 1, 1) 131 4: (E1, E0, EN) = (1, 0, 0) 132 5: (E1, E0, EN) = (1, 0, 1) 133 6: (E1, E0, EN) = (1, 1, 0) 134 7: (E1, E0, EN) = (1, 1, 1) 135 So the valid arguments are from 0 to 7. 136 $ref: /schemas/types.yaml#/definitions/uint32 137 enum: [0, 1, 2, 3, 4, 5, 6, 7] 138 139 mediatek,pull-up-adv: 140 description: | 141 Pull up setings for 2 pull resistors, R0 and R1. User can 142 configure those special pins. Valid arguments are described as below: 143 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 144 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 145 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. 146 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. 147 $ref: /schemas/types.yaml#/definitions/uint32 148 enum: [0, 1, 2, 3] 149 150 mediatek,pull-down-adv: 151 description: | 152 Pull down settings for 2 pull resistors, R0 and R1. User can 153 configure those special pins. Valid arguments are described as below: 154 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 155 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 156 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. 157 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. 158 $ref: /schemas/types.yaml#/definitions/uint32 159 enum: [0, 1, 2, 3] 160 161 mediatek,tdsel: 162 description: | 163 An integer describing the steps for output level shifter duty 164 cycle when asserted (high pulse width adjustment). Valid arguments 165 are from 0 to 15. 166 $ref: /schemas/types.yaml#/definitions/uint32 167 168 mediatek,rdsel: 169 description: | 170 An integer describing the steps for input level shifter duty cycle 171 when asserted (high pulse width adjustment). Valid arguments are 172 from 0 to 63. 173 $ref: /schemas/types.yaml#/definitions/uint32 174 175 required: 176 - pinmux 177 178additionalProperties: false 179 180examples: 181 - | 182 #include <dt-bindings/interrupt-controller/irq.h> 183 #include <dt-bindings/interrupt-controller/arm-gic.h> 184 #include <dt-bindings/pinctrl/mt8183-pinfunc.h> 185 186 soc { 187 #address-cells = <2>; 188 #size-cells = <2>; 189 190 pio: pinctrl@10005000 { 191 compatible = "mediatek,mt8183-pinctrl"; 192 reg = <0 0x10005000 0 0x1000>, 193 <0 0x11f20000 0 0x1000>, 194 <0 0x11e80000 0 0x1000>, 195 <0 0x11e70000 0 0x1000>, 196 <0 0x11e90000 0 0x1000>, 197 <0 0x11d30000 0 0x1000>, 198 <0 0x11d20000 0 0x1000>, 199 <0 0x11c50000 0 0x1000>, 200 <0 0x11f30000 0 0x1000>, 201 <0 0x1000b000 0 0x1000>; 202 reg-names = "iocfg0", "iocfg1", "iocfg2", 203 "iocfg3", "iocfg4", "iocfg5", 204 "iocfg6", "iocfg7", "iocfg8", 205 "eint"; 206 gpio-controller; 207 #gpio-cells = <2>; 208 gpio-ranges = <&pio 0 0 192>; 209 interrupt-controller; 210 interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; 211 #interrupt-cells = <2>; 212 213 i2c0_pins_a: i2c-0 { 214 pins1 { 215 pinmux = <PINMUX_GPIO48__FUNC_SCL5>, 216 <PINMUX_GPIO49__FUNC_SDA5>; 217 mediatek,pull-up-adv = <3>; 218 mediatek,drive-strength-adv = <7>; 219 }; 220 }; 221 222 i2c1_pins_a: i2c-1 { 223 pins { 224 pinmux = <PINMUX_GPIO50__FUNC_SCL3>, 225 <PINMUX_GPIO51__FUNC_SDA3>; 226 mediatek,pull-down-adv = <2>; 227 mediatek,drive-strength-adv = <4>; 228 }; 229 }; 230 }; 231 };