qcom,msm8976-pinctrl.txt (5740B)
1Qualcomm MSM8976 TLMM block 2 3This binding describes the Top Level Mode Multiplexer block found in the 4MSM8956 and MSM8976 platforms. 5 6- compatible: 7 Usage: required 8 Value type: <string> 9 Definition: must be "qcom,msm8976-pinctrl" 10 11- reg: 12 Usage: required 13 Value type: <prop-encoded-array> 14 Definition: the base address and size of the TLMM register space. 15 16- interrupts: 17 Usage: required 18 Value type: <prop-encoded-array> 19 Definition: should specify the TLMM summary IRQ. 20 21- interrupt-controller: 22 Usage: required 23 Value type: <none> 24 Definition: identifies this node as an interrupt controller 25 26- #interrupt-cells: 27 Usage: required 28 Value type: <u32> 29 Definition: must be 2. Specifying the pin number and flags, as defined 30 in <dt-bindings/interrupt-controller/irq.h> 31 32- gpio-controller: 33 Usage: required 34 Value type: <none> 35 Definition: identifies this node as a gpio controller 36 37- #gpio-cells: 38 Usage: required 39 Value type: <u32> 40 Definition: must be 2. Specifying the pin number and flags, as defined 41 in <dt-bindings/gpio/gpio.h> 42 43- gpio-ranges: 44 Usage: required 45 Definition: see ../gpio/gpio.txt 46 47- gpio-reserved-ranges: 48 Usage: optional 49 Definition: see ../gpio/gpio.txt 50 51Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for 52a general description of GPIO and interrupt bindings. 53 54Please refer to pinctrl-bindings.txt in this directory for details of the 55common pinctrl bindings used by client devices, including the meaning of the 56phrase "pin configuration node". 57 58The pin configuration nodes act as a container for an arbitrary number of 59subnodes. Each of these subnodes represents some desired configuration for a 60pin, a group, or a list of pins or groups. This configuration can include the 61mux function to select on those pin(s)/group(s), and various pin configuration 62parameters, such as pull-up, drive strength, etc. 63 64 65PIN CONFIGURATION NODES: 66 67The name of each subnode is not important; all subnodes should be enumerated 68and processed purely based on their content. 69 70Each subnode only affects those parameters that are explicitly listed. In 71other words, a subnode that lists a mux function but no pin configuration 72parameters implies no information about any pin configuration parameters. 73Similarly, a pin subnode that describes a pullup parameter implies no 74information about e.g. the mux function. 75 76 77The following generic properties as defined in pinctrl-bindings.txt are valid 78to specify in a pin configuration subnode: 79 80- pins: 81 Usage: required 82 Value type: <string-array> 83 Definition: List of gpio pins affected by the properties specified in 84 this subnode. 85 86 Valid pins are: 87 gpio0-gpio145 88 Supports mux, bias and drive-strength 89 90 sdc1_clk, sdc1_cmd, sdc1_data, 91 sdc2_clk, sdc2_cmd, sdc2_data, 92 sdc3_clk, sdc3_cmd, sdc3_data 93 Supports bias and drive-strength 94 95- function: 96 Usage: required 97 Value type: <string> 98 Definition: Specify the alternative function to be configured for the 99 specified pins. Functions are only valid for gpio pins. 100 Valid values are: 101 102 gpio, blsp_uart1, blsp_spi1, smb_int, blsp_i2c1, blsp_spi2, 103 blsp_uart2, blsp_i2c2, gcc_gp1_clk_b, blsp_spi3, 104 qdss_tracedata_b, blsp_i2c3, gcc_gp2_clk_b, gcc_gp3_clk_b, 105 blsp_spi4, cap_int, blsp_i2c4, blsp_spi5, blsp_uart5, 106 qdss_traceclk_a, m_voc, blsp_i2c5, qdss_tracectl_a, 107 qdss_tracedata_a, blsp_spi6, blsp_uart6, qdss_tracectl_b, 108 blsp_i2c6, qdss_traceclk_b, mdp_vsync, pri_mi2s_mclk_a, 109 sec_mi2s_mclk_a, cam_mclk, cci0_i2c, cci1_i2c, blsp1_spi, 110 blsp3_spi, gcc_gp1_clk_a, gcc_gp2_clk_a, gcc_gp3_clk_a, 111 uim_batt, sd_write, uim1_data, uim1_clk, uim1_reset, 112 uim1_present, uim2_data, uim2_clk, uim2_reset, 113 uim2_present, ts_xvdd, mipi_dsi0, us_euro, ts_resout, 114 ts_sample, sec_mi2s_mclk_b, pri_mi2s, codec_reset, 115 cdc_pdm0, us_emitter, pri_mi2s_mclk_b, pri_mi2s_mclk_c, 116 lpass_slimbus, lpass_slimbus0, lpass_slimbus1, codec_int1, 117 codec_int2, wcss_bt, sdc3, wcss_wlan2, wcss_wlan1, 118 wcss_wlan0, wcss_wlan, wcss_fm, key_volp, key_snapshot, 119 key_focus, key_home, pwr_down, dmic0_clk, hdmi_int, 120 dmic0_data, wsa_vi, wsa_en, blsp_spi8, wsa_irq, blsp_i2c8, 121 pa_indicator, modem_tsync, ssbi_wtr1, gsm1_tx, gsm0_tx, 122 sdcard_det, sec_mi2s, ss_switch, 123 124- bias-disable: 125 Usage: optional 126 Value type: <none> 127 Definition: The specified pins should be configured as no pull. 128 129- bias-pull-down: 130 Usage: optional 131 Value type: <none> 132 Definition: The specified pins should be configured as pull down. 133 134- bias-pull-up: 135 Usage: optional 136 Value type: <none> 137 Definition: The specified pins should be configured as pull up. 138 139- output-high: 140 Usage: optional 141 Value type: <none> 142 Definition: The specified pins are configured in output mode, driven 143 high. 144 Not valid for sdc pins. 145 146- output-low: 147 Usage: optional 148 Value type: <none> 149 Definition: The specified pins are configured in output mode, driven 150 low. 151 Not valid for sdc pins. 152 153- drive-strength: 154 Usage: optional 155 Value type: <u32> 156 Definition: Selects the drive strength for the specified pins, in mA. 157 Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 158 159Example: 160 161 tlmm: pinctrl@1000000 { 162 compatible = "qcom,msm8976-pinctrl"; 163 reg = <0x1000000 0x300000>; 164 interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; 165 gpio-controller; 166 #gpio-cells = <2>; 167 gpio-ranges = <&tlmm 0 0 145>; 168 interrupt-controller; 169 #interrupt-cells = <2>; 170 171 blsp1_uart2_active: blsp1_uart2_active { 172 mux { 173 pins = "gpio4", "gpio5", "gpio6", "gpio7"; 174 function = "blsp_uart2"; 175 }; 176 177 config { 178 pins = "gpio4", "gpio5", "gpio6", "gpio7"; 179 drive-strength = <2>; 180 bias-disable; 181 }; 182 }; 183 };