cs35l33.txt (4764B)
1CS35L33 Speaker Amplifier 2 3Required properties: 4 5 - compatible : "cirrus,cs35l33" 6 7 - reg : the I2C address of the device for I2C 8 9 - VA-supply, VP-supply : power supplies for the device, 10 as covered in 11 Documentation/devicetree/bindings/regulator/regulator.txt. 12 13Optional properties: 14 15 - reset-gpios : gpio used to reset the amplifier 16 17 - interrupts : IRQ line info CS35L33. 18 (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt 19 for further information relating to interrupt properties) 20 21 - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is 22 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with 23 a value of 1 and will increase at a step size of 100mV until a maximum of 24 8000mV. 25 26 - cirrus,ramp-rate : On power up, it affects the time from when the power 27 up sequence begins to the time the audio reaches a full-scale output. 28 On power down, it affects the time from when the power-down sequence 29 begins to when the amplifier disables the PWM outputs. If this property 30 is not set then soft ramping will be disabled and ramp time would be 31 20ms. If this property is set to 0,1,2,3 then ramp times would be 40ms, 32 60ms,100ms,175ms respectively for 48KHz sample rate. 33 34 - cirrus,boost-ipk : The maximum current allowed for the boost converter. 35 The range starts at 1850000uA and goes to a maximum of 3600000uA 36 with a step size of 15625uA. The default is 2500000uA. 37 38 - cirrus,imon-adc-scale : Configures the scaling of data bits from the IMON 39 ADC data word. This property can be set as a value of 0 for bits 15 down 40 to 0, 6 for 21 down to 6, 7, for 22 down to 7, 8 for 23 down to 8. 41 42 43Optional H/G Algorithm sub-node: 44 45The cs35l33 node can have a single "cirrus,hg-algo" sub-node that will enable 46the internal H/G Algorithm. 47 48 - cirrus,hg-algo : Sub-node for internal Class H/G algorithm that 49 controls the amplifier supplies. 50 51Optional properties for the "cirrus,hg-algo" sub-node: 52 53 - cirrus,mem-depth : Memory depth for the Class H/G algorithm measured in 54 LRCLK cycles. If this property is set to 0, 1, 2, or 3 then the memory 55 depths will be 1, 4, 8, 16 LRCLK cycles. The default is 16 LRCLK cycles. 56 57 cirrus,release-rate : The number of consecutive LRCLK periods before 58 allowing release condition tracking updates. The number of LRCLK periods 59 start at 3 to a maximum of 255. 60 61 - cirrus,ldo-thld : Configures the signal threshold at which the PWM output 62 stage enters LDO operation. Starts as a default value of 50mV for a value 63 of 1 and increases with a step size of 50mV to a maximum of 750mV (value of 64 0xF). 65 66 - cirrus,ldo-path-disable : This is a boolean property. If present, the H/G 67 algorithm uses the max detection path. If not present, the LDO 68 detection path is used. 69 70 - cirrus,ldo-entry-delay : The LDO entry delay in milliseconds before the H/G 71 algorithm switches to the LDO voltage. This property can be set to values 72 from 0 to 7 for delays of 5ms, 10ms, 50ms, 100ms, 200ms, 500ms, 1000ms. 73 The default is 100ms. 74 75 - cirrus,vp-hg-auto : This is a boolean property. When set, class H/G VPhg 76 automatic updating is enabled. 77 78 - cirrus,vp-hg : Class H/G algorithm VPhg. Controls the H/G algorithm's 79 reference to the VP voltage for when to start generating a boosted VBST. 80 The reference voltage starts at 3000mV with a value of 0x3 and is increased 81 by 100mV per step to a maximum of 5500mV. 82 83 - cirrus,vp-hg-rate : The rate (number of LRCLK periods) at which the VPhg is 84 allowed to increase to a higher voltage when using VPhg automatic 85 tracking. This property can be set to values from 0 to 3 with rates of 128 86 periods, 2048 periods, 32768 periods, and 524288 periods. 87 The default is 32768 periods. 88 89 - cirrus,vp-hg-va : VA calculation reference for automatic VPhg tracking 90 using VPMON. This property can be set to values from 0 to 6 starting at 91 1800mV with a step size of 50mV up to a maximum value of 1750mV. 92 Default is 1800mV. 93 94Example: 95 96cs35l33: cs35l33@40 { 97 compatible = "cirrus,cs35l33"; 98 reg = <0x40>; 99 100 VA-supply = <&ldo5_reg>; 101 VP-supply = <&ldo5_reg>; 102 103 interrupt-parent = <&gpio8>; 104 interrupts = <3 IRQ_TYPE_LEVEL_LOW>; 105 106 reset-gpios = <&cs47l91 34 0>; 107 108 cirrus,ramp-rate = <0x0>; 109 cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */ 110 cirrus,boost-ipk = <0xE0>; /* 3600mA */ 111 cirrus,imon-adc-scale = <0> /* Bits 15 down to 0 */ 112 113 cirrus,hg-algo { 114 cirrus,mem-depth = <0x3>; 115 cirrus,release-rate = <0x3>; 116 cirrus,ldo-thld = <0x1>; 117 cirrus,ldo-path-disable = <0x0>; 118 cirrus,ldo-entry-delay=<0x4>; 119 cirrus,vp-hg-auto; 120 cirrus,vp-hg=<0xF>; 121 cirrus,vp-hg-rate=<0x2>; 122 cirrus,vp-hg-va=<0x0>; 123 }; 124};