cachepc-linux

Fork of AMDESE/linux with modifications for CachePC side-channel attack
git clone https://git.sinitax.com/sinitax/cachepc-linux
Log | Files | Refs | README | LICENSE | sfeed.txt

rt5640.txt (2155B)


      1RT5640/RT5639 audio CODEC
      2
      3This device supports I2C only.
      4
      5Required properties:
      6
      7- compatible : One of "realtek,rt5640" or "realtek,rt5639".
      8
      9- reg : The I2C address of the device.
     10
     11- interrupts : The CODEC's interrupt output.
     12
     13Optional properties:
     14
     15- clocks: The phandle of the master clock to the CODEC
     16- clock-names: Should be "mclk"
     17
     18- realtek,in1-differential
     19- realtek,in2-differential
     20- realtek,in3-differential
     21  Boolean. Indicate MIC1/2/3 input are differential, rather than single-ended.
     22
     23- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
     24
     25- realtek,dmic1-data-pin
     26  0: dmic1 is not used
     27  1: using IN1P pin as dmic1 data pin
     28  2: using GPIO3 pin as dmic1 data pin
     29
     30- realtek,dmic2-data-pin
     31  0: dmic2 is not used
     32  1: using IN1N pin as dmic2 data pin
     33  2: using GPIO4 pin as dmic2 data pin
     34
     35- realtek,jack-detect-source
     36  u32. Valid values:
     37  0: jack-detect is not used
     38  1: Use GPIO1 for jack-detect
     39  2: Use JD1_IN4P for jack-detect
     40  3: Use JD2_IN4N for jack-detect
     41  4: Use GPIO2 for jack-detect
     42  5: Use GPIO3 for jack-detect
     43  6: Use GPIO4 for jack-detect
     44
     45- realtek,jack-detect-not-inverted
     46  bool. Normal jack-detect switches give an inverted signal, set this bool
     47  in the rare case you've a jack-detect switch which is not inverted.
     48
     49- realtek,over-current-threshold-microamp
     50  u32, micbias over-current detection threshold in µA, valid values are
     51  600, 1500 and 2000µA.
     52
     53- realtek,over-current-scale-factor
     54  u32, micbias over-current detection scale-factor, valid values are:
     55  0: Scale current by 0.5
     56  1: Scale current by 0.75
     57  2: Scale current by 1.0
     58  3: Scale current by 1.5
     59
     60Pins on the device (for linking into audio routes) for RT5639/RT5640:
     61
     62  * DMIC1
     63  * DMIC2
     64  * MICBIAS1
     65  * IN1P
     66  * IN1N
     67  * IN2P
     68  * IN2N
     69  * IN3P
     70  * IN3N
     71  * HPOL
     72  * HPOR
     73  * LOUTL
     74  * LOUTR
     75  * SPOLP
     76  * SPOLN
     77  * SPORP
     78  * SPORN
     79
     80Additional pins on the device for RT5640:
     81
     82  * MONOP
     83  * MONON
     84
     85Example:
     86
     87rt5640 {
     88	compatible = "realtek,rt5640";
     89	reg = <0x1c>;
     90	interrupt-parent = <&gpio>;
     91	interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_HIGH>;
     92	realtek,ldo1-en-gpios =
     93		<&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
     94};