spi-orion.txt (3322B)
1Marvell Orion SPI device 2 3Required properties: 4- compatible : should be on of the following: 5 - "marvell,orion-spi" for the Orion, mv78x00, Kirkwood and Dove SoCs 6 - "marvell,armada-370-spi", for the Armada 370 SoCs 7 - "marvell,armada-375-spi", for the Armada 375 SoCs 8 - "marvell,armada-380-spi", for the Armada 38x SoCs 9 - "marvell,armada-390-spi", for the Armada 39x SoCs 10 - "marvell,armada-xp-spi", for the Armada XP SoCs 11- reg : offset and length of the register set for the device. 12 This property can optionally have additional entries to configure 13 the SPI direct access mode that some of the Marvell SoCs support 14 additionally to the normal indirect access (PIO) mode. The values 15 for the MBus "target" and "attribute" are defined in the Marvell 16 SoC "Functional Specifications" Manual in the chapter "Marvell 17 Core Processor Address Decoding". 18 The eight register sets following the control registers refer to 19 chip-select lines 0 through 7 respectively. 20- cell-index : Which of multiple SPI controllers is this. 21- clocks : pointers to the reference clocks for this device, the first 22 one is the one used for the clock on the spi bus, the 23 second one is optional and is the clock used for the 24 functional part of the controller 25 26Optional properties: 27- interrupts : Is currently not used. 28- clock-names : names of used clocks, mandatory if the second clock is 29 used, the name must be "core", and "axi" (the latter 30 is only for Armada 7K/8K). 31 32 33Example: 34 spi@10600 { 35 compatible = "marvell,orion-spi"; 36 #address-cells = <1>; 37 #size-cells = <0>; 38 cell-index = <0>; 39 reg = <0x10600 0x28>; 40 interrupts = <23>; 41 }; 42 43Example with SPI direct mode support (optionally): 44 spi0: spi@10600 { 45 compatible = "marvell,orion-spi"; 46 #address-cells = <1>; 47 #size-cells = <0>; 48 cell-index = <0>; 49 reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x28>, /* control */ 50 <MBUS_ID(0x01, 0x1e) 0 0xffffffff>, /* CS0 */ 51 <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */ 52 <MBUS_ID(0x01, 0x9e) 0 0xffffffff>, /* CS2 */ 53 <MBUS_ID(0x01, 0xde) 0 0xffffffff>, /* CS3 */ 54 <MBUS_ID(0x01, 0x1f) 0 0xffffffff>, /* CS4 */ 55 <MBUS_ID(0x01, 0x5f) 0 0xffffffff>, /* CS5 */ 56 <MBUS_ID(0x01, 0x9f) 0 0xffffffff>, /* CS6 */ 57 <MBUS_ID(0x01, 0xdf) 0 0xffffffff>; /* CS7 */ 58 interrupts = <23>; 59 }; 60 61To enable the direct mode, the board specific 'ranges' property in the 62'soc' node needs to add the entries for the desired SPI controllers 63and its chip-selects that are used in the direct mode instead of PIO 64mode. Here an example for this (SPI controller 0, device 1 and SPI 65controller 1, device 2 are used in direct mode. All other SPI device 66are used in the default indirect (PIO) mode): 67 soc { 68 /* 69 * Enable the SPI direct access by configuring an entry 70 * here in the board-specific ranges property 71 */ 72 ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000>, /* internal regs */ 73 <MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>, /* BootROM */ 74 <MBUS_ID(0x01, 0x5e) 0 0 0xf1100000 0x10000>, /* SPI0-DEV1 */ 75 <MBUS_ID(0x01, 0x9a) 0 0 0xf1110000 0x10000>; /* SPI1-DEV2 */ 76 77For further information on the MBus bindings, please see the MBus 78DT documentation: 79Documentation/devicetree/bindings/bus/mvebu-mbus.txt