cx2341x-devel.rst (70430B)
1.. SPDX-License-Identifier: GPL-2.0 2 3The cx2341x driver 4================== 5 6Memory at cx2341x chips 7----------------------- 8 9This section describes the cx2341x memory map and documents some of the 10register space. 11 12.. note:: the memory long words are little-endian ('intel format'). 13 14.. warning:: 15 16 This information was figured out from searching through the memory 17 and registers, this information may not be correct and is certainly 18 not complete, and was not derived from anything more than searching 19 through the memory space with commands like: 20 21 .. code-block:: none 22 23 ivtvctl -O min=0x02000000,max=0x020000ff 24 25 So take this as is, I'm always searching for more stuff, it's a large 26 register space :-). 27 28Memory Map 29~~~~~~~~~~ 30 31The cx2341x exposes its entire 64M memory space to the PCI host via the PCI BAR0 32(Base Address Register 0). The addresses here are offsets relative to the 33address held in BAR0. 34 35.. code-block:: none 36 37 0x00000000-0x00ffffff Encoder memory space 38 0x00000000-0x0003ffff Encode.rom 39 ???-??? MPEG buffer(s) 40 ???-??? Raw video capture buffer(s) 41 ???-??? Raw audio capture buffer(s) 42 ???-??? Display buffers (6 or 9) 43 44 0x01000000-0x01ffffff Decoder memory space 45 0x01000000-0x0103ffff Decode.rom 46 ???-??? MPEG buffers(s) 47 0x0114b000-0x0115afff Audio.rom (deprecated?) 48 49 0x02000000-0x0200ffff Register Space 50 51Registers 52~~~~~~~~~ 53 54The registers occupy the 64k space starting at the 0x02000000 offset from BAR0. 55All of these registers are 32 bits wide. 56 57.. code-block:: none 58 59 DMA Registers 0x000-0xff: 60 61 0x00 - Control: 62 0=reset/cancel, 1=read, 2=write, 4=stop 63 0x04 - DMA status: 64 1=read busy, 2=write busy, 4=read error, 8=write error, 16=link list error 65 0x08 - pci DMA pointer for read link list 66 0x0c - pci DMA pointer for write link list 67 0x10 - read/write DMA enable: 68 1=read enable, 2=write enable 69 0x14 - always 0xffffffff, if set any lower instability occurs, 0x00 crashes 70 0x18 - ?? 71 0x1c - always 0x20 or 32, smaller values slow down DMA transactions 72 0x20 - always value of 0x780a010a 73 0x24-0x3c - usually just random values??? 74 0x40 - Interrupt status 75 0x44 - Write a bit here and shows up in Interrupt status 0x40 76 0x48 - Interrupt Mask 77 0x4C - always value of 0xfffdffff, 78 if changed to 0xffffffff DMA write interrupts break. 79 0x50 - always 0xffffffff 80 0x54 - always 0xffffffff (0x4c, 0x50, 0x54 seem like interrupt masks, are 81 3 processors on chip, Java ones, VPU, SPU, APU, maybe these are the 82 interrupt masks???). 83 0x60-0x7C - random values 84 0x80 - first write linked list reg, for Encoder Memory addr 85 0x84 - first write linked list reg, for pci memory addr 86 0x88 - first write linked list reg, for length of buffer in memory addr 87 (|0x80000000 or this for last link) 88 0x8c-0xdc - rest of write linked list reg, 8 sets of 3 total, DMA goes here 89 from linked list addr in reg 0x0c, firmware must push through or 90 something. 91 0xe0 - first (and only) read linked list reg, for pci memory addr 92 0xe4 - first (and only) read linked list reg, for Decoder memory addr 93 0xe8 - first (and only) read linked list reg, for length of buffer 94 0xec-0xff - Nothing seems to be in these registers, 0xec-f4 are 0x00000000. 95 96Memory locations for Encoder Buffers 0x700-0x7ff: 97 98These registers show offsets of memory locations pertaining to each 99buffer area used for encoding, have to shift them by <<1 first. 100 101- 0x07F8: Encoder SDRAM refresh 102- 0x07FC: Encoder SDRAM pre-charge 103 104Memory locations for Decoder Buffers 0x800-0x8ff: 105 106These registers show offsets of memory locations pertaining to each 107buffer area used for decoding, have to shift them by <<1 first. 108 109- 0x08F8: Decoder SDRAM refresh 110- 0x08FC: Decoder SDRAM pre-charge 111 112Other memory locations: 113 114- 0x2800: Video Display Module control 115- 0x2D00: AO (audio output?) control 116- 0x2D24: Bytes Flushed 117- 0x7000: LSB I2C write clock bit (inverted) 118- 0x7004: LSB I2C write data bit (inverted) 119- 0x7008: LSB I2C read clock bit 120- 0x700c: LSB I2C read data bit 121- 0x9008: GPIO get input state 122- 0x900c: GPIO set output state 123- 0x9020: GPIO direction (Bit7 (GPIO 0..7) - 0:input, 1:output) 124- 0x9050: SPU control 125- 0x9054: Reset HW blocks 126- 0x9058: VPU control 127- 0xA018: Bit6: interrupt pending? 128- 0xA064: APU command 129 130 131Interrupt Status Register 132~~~~~~~~~~~~~~~~~~~~~~~~~ 133 134The definition of the bits in the interrupt status register 0x0040, and the 135interrupt mask 0x0048. If a bit is cleared in the mask, then we want our ISR to 136execute. 137 138- bit 31 Encoder Start Capture 139- bit 30 Encoder EOS 140- bit 29 Encoder VBI capture 141- bit 28 Encoder Video Input Module reset event 142- bit 27 Encoder DMA complete 143- bit 24 Decoder audio mode change detection event (through event notification) 144- bit 22 Decoder data request 145- bit 20 Decoder DMA complete 146- bit 19 Decoder VBI re-insertion 147- bit 18 Decoder DMA err (linked-list bad) 148 149Missing documentation 150--------------------- 151 152- Encoder API post(?) 153- Decoder API post(?) 154- Decoder VTRACE event 155 156 157The cx2341x firmware upload 158--------------------------- 159 160This document describes how to upload the cx2341x firmware to the card. 161 162How to find 163~~~~~~~~~~~ 164 165See the web pages of the various projects that uses this chip for information 166on how to obtain the firmware. 167 168The firmware stored in a Windows driver can be detected as follows: 169 170- Each firmware image is 256k bytes. 171- The 1st 32-bit word of the Encoder image is 0x0000da7 172- The 1st 32-bit word of the Decoder image is 0x00003a7 173- The 2nd 32-bit word of both images is 0xaa55bb66 174 175How to load 176~~~~~~~~~~~ 177 178- Issue the FWapi command to stop the encoder if it is running. Wait for the 179 command to complete. 180- Issue the FWapi command to stop the decoder if it is running. Wait for the 181 command to complete. 182- Issue the I2C command to the digitizer to stop emitting VSYNC events. 183- Issue the FWapi command to halt the encoder's firmware. 184- Sleep for 10ms. 185- Issue the FWapi command to halt the decoder's firmware. 186- Sleep for 10ms. 187- Write 0x00000000 to register 0x2800 to stop the Video Display Module. 188- Write 0x00000005 to register 0x2D00 to stop the AO (audio output?). 189- Write 0x00000000 to register 0xA064 to ping? the APU. 190- Write 0xFFFFFFFE to register 0x9058 to stop the VPU. 191- Write 0xFFFFFFFF to register 0x9054 to reset the HW blocks. 192- Write 0x00000001 to register 0x9050 to stop the SPU. 193- Sleep for 10ms. 194- Write 0x0000001A to register 0x07FC to init the Encoder SDRAM's pre-charge. 195- Write 0x80000640 to register 0x07F8 to init the Encoder SDRAM's refresh to 1us. 196- Write 0x0000001A to register 0x08FC to init the Decoder SDRAM's pre-charge. 197- Write 0x80000640 to register 0x08F8 to init the Decoder SDRAM's refresh to 1us. 198- Sleep for 512ms. (600ms is recommended) 199- Transfer the encoder's firmware image to offset 0 in Encoder memory space. 200- Transfer the decoder's firmware image to offset 0 in Decoder memory space. 201- Use a read-modify-write operation to Clear bit 0 of register 0x9050 to 202 re-enable the SPU. 203- Sleep for 1 second. 204- Use a read-modify-write operation to Clear bits 3 and 0 of register 0x9058 205 to re-enable the VPU. 206- Sleep for 1 second. 207- Issue status API commands to both firmware images to verify. 208 209 210How to call the firmware API 211---------------------------- 212 213The preferred calling convention is known as the firmware mailbox. The 214mailboxes are basically a fixed length array that serves as the call-stack. 215 216Firmware mailboxes can be located by searching the encoder and decoder memory 217for a 16 byte signature. That signature will be located on a 256-byte boundary. 218 219Signature: 220 221.. code-block:: none 222 223 0x78, 0x56, 0x34, 0x12, 0x12, 0x78, 0x56, 0x34, 224 0x34, 0x12, 0x78, 0x56, 0x56, 0x34, 0x12, 0x78 225 226The firmware implements 20 mailboxes of 20 32-bit words. The first 10 are 227reserved for API calls. The second 10 are used by the firmware for event 228notification. 229 230 ====== ================= 231 Index Name 232 ====== ================= 233 0 Flags 234 1 Command 235 2 Return value 236 3 Timeout 237 4-19 Parameter/Result 238 ====== ================= 239 240 241The flags are defined in the following table. The direction is from the 242perspective of the firmware. 243 244 ==== ========== ============================================ 245 Bit Direction Purpose 246 ==== ========== ============================================ 247 2 O Firmware has processed the command. 248 1 I Driver has finished setting the parameters. 249 0 I Driver is using this mailbox. 250 ==== ========== ============================================ 251 252The command is a 32-bit enumerator. The API specifics may be found in this 253chapter. 254 255The return value is a 32-bit enumerator. Only two values are currently defined: 256 257- 0=success 258- -1=command undefined. 259 260There are 16 parameters/results 32-bit fields. The driver populates these fields 261with values for all the parameters required by the call. The driver overwrites 262these fields with result values returned by the call. 263 264The timeout value protects the card from a hung driver thread. If the driver 265doesn't handle the completed call within the timeout specified, the firmware 266will reset that mailbox. 267 268To make an API call, the driver iterates over each mailbox looking for the 269first one available (bit 0 has been cleared). The driver sets that bit, fills 270in the command enumerator, the timeout value and any required parameters. The 271driver then sets the parameter ready bit (bit 1). The firmware scans the 272mailboxes for pending commands, processes them, sets the result code, populates 273the result value array with that call's return values and sets the call 274complete bit (bit 2). Once bit 2 is set, the driver should retrieve the results 275and clear all the flags. If the driver does not perform this task within the 276time set in the timeout register, the firmware will reset that mailbox. 277 278Event notifications are sent from the firmware to the host. The host tells the 279firmware which events it is interested in via an API call. That call tells the 280firmware which notification mailbox to use. The firmware signals the host via 281an interrupt. Only the 16 Results fields are used, the Flags, Command, Return 282value and Timeout words are not used. 283 284 285OSD firmware API description 286---------------------------- 287 288.. note:: this API is part of the decoder firmware, so it's cx23415 only. 289 290 291 292CX2341X_OSD_GET_FRAMEBUFFER 293~~~~~~~~~~~~~~~~~~~~~~~~~~~ 294 295Enum: 65/0x41 296 297Description 298^^^^^^^^^^^ 299 300Return base and length of contiguous OSD memory. 301 302Result[0] 303^^^^^^^^^ 304 305OSD base address 306 307Result[1] 308^^^^^^^^^ 309 310OSD length 311 312 313 314CX2341X_OSD_GET_PIXEL_FORMAT 315~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 316 317Enum: 66/0x42 318 319Description 320^^^^^^^^^^^ 321 322Query OSD format 323 324Result[0] 325^^^^^^^^^ 326 3270=8bit index 3281=16bit RGB 5:6:5 3292=16bit ARGB 1:5:5:5 3303=16bit ARGB 1:4:4:4 3314=32bit ARGB 8:8:8:8 332 333 334 335CX2341X_OSD_SET_PIXEL_FORMAT 336~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 337 338Enum: 67/0x43 339 340Description 341^^^^^^^^^^^ 342 343Assign pixel format 344 345Param[0] 346^^^^^^^^ 347 348- 0=8bit index 349- 1=16bit RGB 5:6:5 350- 2=16bit ARGB 1:5:5:5 351- 3=16bit ARGB 1:4:4:4 352- 4=32bit ARGB 8:8:8:8 353 354 355 356CX2341X_OSD_GET_STATE 357~~~~~~~~~~~~~~~~~~~~~ 358 359Enum: 68/0x44 360 361Description 362^^^^^^^^^^^ 363 364Query OSD state 365 366Result[0] 367^^^^^^^^^ 368 369- Bit 0 0=off, 1=on 370- Bits 1:2 alpha control 371- Bits 3:5 pixel format 372 373 374 375CX2341X_OSD_SET_STATE 376~~~~~~~~~~~~~~~~~~~~~ 377 378Enum: 69/0x45 379 380Description 381^^^^^^^^^^^ 382 383OSD switch 384 385Param[0] 386^^^^^^^^ 387 3880=off, 1=on 389 390 391 392CX2341X_OSD_GET_OSD_COORDS 393~~~~~~~~~~~~~~~~~~~~~~~~~~ 394 395Enum: 70/0x46 396 397Description 398^^^^^^^^^^^ 399 400Retrieve coordinates of OSD area blended with video 401 402Result[0] 403^^^^^^^^^ 404 405OSD buffer address 406 407Result[1] 408^^^^^^^^^ 409 410Stride in pixels 411 412Result[2] 413^^^^^^^^^ 414 415Lines in OSD buffer 416 417Result[3] 418^^^^^^^^^ 419 420Horizontal offset in buffer 421 422Result[4] 423^^^^^^^^^ 424 425Vertical offset in buffer 426 427 428 429CX2341X_OSD_SET_OSD_COORDS 430~~~~~~~~~~~~~~~~~~~~~~~~~~ 431 432Enum: 71/0x47 433 434Description 435^^^^^^^^^^^ 436 437Assign the coordinates of the OSD area to blend with video 438 439Param[0] 440^^^^^^^^ 441 442buffer address 443 444Param[1] 445^^^^^^^^ 446 447buffer stride in pixels 448 449Param[2] 450^^^^^^^^ 451 452lines in buffer 453 454Param[3] 455^^^^^^^^ 456 457horizontal offset 458 459Param[4] 460^^^^^^^^ 461 462vertical offset 463 464 465 466CX2341X_OSD_GET_SCREEN_COORDS 467~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 468 469Enum: 72/0x48 470 471Description 472^^^^^^^^^^^ 473 474Retrieve OSD screen area coordinates 475 476Result[0] 477^^^^^^^^^ 478 479top left horizontal offset 480 481Result[1] 482^^^^^^^^^ 483 484top left vertical offset 485 486Result[2] 487^^^^^^^^^ 488 489bottom right horizontal offset 490 491Result[3] 492^^^^^^^^^ 493 494bottom right vertical offset 495 496 497 498CX2341X_OSD_SET_SCREEN_COORDS 499~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 500 501Enum: 73/0x49 502 503Description 504^^^^^^^^^^^ 505 506Assign the coordinates of the screen area to blend with video 507 508Param[0] 509^^^^^^^^ 510 511top left horizontal offset 512 513Param[1] 514^^^^^^^^ 515 516top left vertical offset 517 518Param[2] 519^^^^^^^^ 520 521bottom left horizontal offset 522 523Param[3] 524^^^^^^^^ 525 526bottom left vertical offset 527 528 529 530CX2341X_OSD_GET_GLOBAL_ALPHA 531~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 532 533Enum: 74/0x4A 534 535Description 536^^^^^^^^^^^ 537 538Retrieve OSD global alpha 539 540Result[0] 541^^^^^^^^^ 542 543global alpha: 0=off, 1=on 544 545Result[1] 546^^^^^^^^^ 547 548bits 0:7 global alpha 549 550 551 552CX2341X_OSD_SET_GLOBAL_ALPHA 553~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 554 555Enum: 75/0x4B 556 557Description 558^^^^^^^^^^^ 559 560Update global alpha 561 562Param[0] 563^^^^^^^^ 564 565global alpha: 0=off, 1=on 566 567Param[1] 568^^^^^^^^ 569 570global alpha (8 bits) 571 572Param[2] 573^^^^^^^^ 574 575local alpha: 0=on, 1=off 576 577 578 579CX2341X_OSD_SET_BLEND_COORDS 580~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 581 582Enum: 78/0x4C 583 584Description 585^^^^^^^^^^^ 586 587Move start of blending area within display buffer 588 589Param[0] 590^^^^^^^^ 591 592horizontal offset in buffer 593 594Param[1] 595^^^^^^^^ 596 597vertical offset in buffer 598 599 600 601CX2341X_OSD_GET_FLICKER_STATE 602~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 603 604Enum: 79/0x4F 605 606Description 607^^^^^^^^^^^ 608 609Retrieve flicker reduction module state 610 611Result[0] 612^^^^^^^^^ 613 614flicker state: 0=off, 1=on 615 616 617 618CX2341X_OSD_SET_FLICKER_STATE 619~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 620 621Enum: 80/0x50 622 623Description 624^^^^^^^^^^^ 625 626Set flicker reduction module state 627 628Param[0] 629^^^^^^^^ 630 631State: 0=off, 1=on 632 633 634 635CX2341X_OSD_BLT_COPY 636~~~~~~~~~~~~~~~~~~~~ 637 638Enum: 82/0x52 639 640Description 641^^^^^^^^^^^ 642 643BLT copy 644 645Param[0] 646^^^^^^^^ 647 648.. code-block:: none 649 650 '0000' zero 651 '0001' ~destination AND ~source 652 '0010' ~destination AND source 653 '0011' ~destination 654 '0100' destination AND ~source 655 '0101' ~source 656 '0110' destination XOR source 657 '0111' ~destination OR ~source 658 '1000' ~destination AND ~source 659 '1001' destination XNOR source 660 '1010' source 661 '1011' ~destination OR source 662 '1100' destination 663 '1101' destination OR ~source 664 '1110' destination OR source 665 '1111' one 666 667 668Param[1] 669^^^^^^^^ 670 671Resulting alpha blending 672 673- '01' source_alpha 674- '10' destination_alpha 675- '11' source_alpha*destination_alpha+1 676 (zero if both source and destination alpha are zero) 677 678Param[2] 679^^^^^^^^ 680 681.. code-block:: none 682 683 '00' output_pixel = source_pixel 684 685 '01' if source_alpha=0: 686 output_pixel = destination_pixel 687 if 256 > source_alpha > 1: 688 output_pixel = ((source_alpha + 1)*source_pixel + 689 (255 - source_alpha)*destination_pixel)/256 690 691 '10' if destination_alpha=0: 692 output_pixel = source_pixel 693 if 255 > destination_alpha > 0: 694 output_pixel = ((255 - destination_alpha)*source_pixel + 695 (destination_alpha + 1)*destination_pixel)/256 696 697 '11' if source_alpha=0: 698 source_temp = 0 699 if source_alpha=255: 700 source_temp = source_pixel*256 701 if 255 > source_alpha > 0: 702 source_temp = source_pixel*(source_alpha + 1) 703 if destination_alpha=0: 704 destination_temp = 0 705 if destination_alpha=255: 706 destination_temp = destination_pixel*256 707 if 255 > destination_alpha > 0: 708 destination_temp = destination_pixel*(destination_alpha + 1) 709 output_pixel = (source_temp + destination_temp)/256 710 711Param[3] 712^^^^^^^^ 713 714width 715 716Param[4] 717^^^^^^^^ 718 719height 720 721Param[5] 722^^^^^^^^ 723 724destination pixel mask 725 726Param[6] 727^^^^^^^^ 728 729destination rectangle start address 730 731Param[7] 732^^^^^^^^ 733 734destination stride in dwords 735 736Param[8] 737^^^^^^^^ 738 739source stride in dwords 740 741Param[9] 742^^^^^^^^ 743 744source rectangle start address 745 746 747 748CX2341X_OSD_BLT_FILL 749~~~~~~~~~~~~~~~~~~~~ 750 751Enum: 83/0x53 752 753Description 754^^^^^^^^^^^ 755 756BLT fill color 757 758Param[0] 759^^^^^^^^ 760 761Same as Param[0] on API 0x52 762 763Param[1] 764^^^^^^^^ 765 766Same as Param[1] on API 0x52 767 768Param[2] 769^^^^^^^^ 770 771Same as Param[2] on API 0x52 772 773Param[3] 774^^^^^^^^ 775 776width 777 778Param[4] 779^^^^^^^^ 780 781height 782 783Param[5] 784^^^^^^^^ 785 786destination pixel mask 787 788Param[6] 789^^^^^^^^ 790 791destination rectangle start address 792 793Param[7] 794^^^^^^^^ 795 796destination stride in dwords 797 798Param[8] 799^^^^^^^^ 800 801color fill value 802 803 804 805CX2341X_OSD_BLT_TEXT 806~~~~~~~~~~~~~~~~~~~~ 807 808Enum: 84/0x54 809 810Description 811^^^^^^^^^^^ 812 813BLT for 8 bit alpha text source 814 815Param[0] 816^^^^^^^^ 817 818Same as Param[0] on API 0x52 819 820Param[1] 821^^^^^^^^ 822 823Same as Param[1] on API 0x52 824 825Param[2] 826^^^^^^^^ 827 828Same as Param[2] on API 0x52 829 830Param[3] 831^^^^^^^^ 832 833width 834 835Param[4] 836^^^^^^^^ 837 838height 839 840Param[5] 841^^^^^^^^ 842 843destination pixel mask 844 845Param[6] 846^^^^^^^^ 847 848destination rectangle start address 849 850Param[7] 851^^^^^^^^ 852 853destination stride in dwords 854 855Param[8] 856^^^^^^^^ 857 858source stride in dwords 859 860Param[9] 861^^^^^^^^ 862 863source rectangle start address 864 865Param[10] 866^^^^^^^^^ 867 868color fill value 869 870 871 872CX2341X_OSD_SET_FRAMEBUFFER_WINDOW 873~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 874 875Enum: 86/0x56 876 877Description 878^^^^^^^^^^^ 879 880Positions the main output window on the screen. The coordinates must be 881such that the entire window fits on the screen. 882 883Param[0] 884^^^^^^^^ 885 886window width 887 888Param[1] 889^^^^^^^^ 890 891window height 892 893Param[2] 894^^^^^^^^ 895 896top left window corner horizontal offset 897 898Param[3] 899^^^^^^^^ 900 901top left window corner vertical offset 902 903 904 905CX2341X_OSD_SET_CHROMA_KEY 906~~~~~~~~~~~~~~~~~~~~~~~~~~ 907 908Enum: 96/0x60 909 910Description 911^^^^^^^^^^^ 912 913Chroma key switch and color 914 915Param[0] 916^^^^^^^^ 917 918state: 0=off, 1=on 919 920Param[1] 921^^^^^^^^ 922 923color 924 925 926 927CX2341X_OSD_GET_ALPHA_CONTENT_INDEX 928~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 929 930Enum: 97/0x61 931 932Description 933^^^^^^^^^^^ 934 935Retrieve alpha content index 936 937Result[0] 938^^^^^^^^^ 939 940alpha content index, Range 0:15 941 942 943 944CX2341X_OSD_SET_ALPHA_CONTENT_INDEX 945~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 946 947Enum: 98/0x62 948 949Description 950^^^^^^^^^^^ 951 952Assign alpha content index 953 954Param[0] 955^^^^^^^^ 956 957alpha content index, range 0:15 958 959 960Encoder firmware API description 961-------------------------------- 962 963CX2341X_ENC_PING_FW 964~~~~~~~~~~~~~~~~~~~ 965 966Enum: 128/0x80 967 968Description 969^^^^^^^^^^^ 970 971Does nothing. Can be used to check if the firmware is responding. 972 973 974 975CX2341X_ENC_START_CAPTURE 976~~~~~~~~~~~~~~~~~~~~~~~~~ 977 978Enum: 129/0x81 979 980Description 981^^^^^^^^^^^ 982 983Commences the capture of video, audio and/or VBI data. All encoding 984parameters must be initialized prior to this API call. Captures frames 985continuously or until a predefined number of frames have been captured. 986 987Param[0] 988^^^^^^^^ 989 990Capture stream type: 991 992 - 0=MPEG 993 - 1=Raw 994 - 2=Raw passthrough 995 - 3=VBI 996 997 998Param[1] 999^^^^^^^^ 1000 1001Bitmask: 1002 1003 - Bit 0 when set, captures YUV 1004 - Bit 1 when set, captures PCM audio 1005 - Bit 2 when set, captures VBI (same as param[0]=3) 1006 - Bit 3 when set, the capture destination is the decoder 1007 (same as param[0]=2) 1008 - Bit 4 when set, the capture destination is the host 1009 1010.. note:: this parameter is only meaningful for RAW capture type. 1011 1012 1013 1014CX2341X_ENC_STOP_CAPTURE 1015~~~~~~~~~~~~~~~~~~~~~~~~ 1016 1017Enum: 130/0x82 1018 1019Description 1020^^^^^^^^^^^ 1021 1022Ends a capture in progress 1023 1024Param[0] 1025^^^^^^^^ 1026 1027- 0=stop at end of GOP (generates IRQ) 1028- 1=stop immediate (no IRQ) 1029 1030Param[1] 1031^^^^^^^^ 1032 1033Stream type to stop, see param[0] of API 0x81 1034 1035Param[2] 1036^^^^^^^^ 1037 1038Subtype, see param[1] of API 0x81 1039 1040 1041 1042CX2341X_ENC_SET_AUDIO_ID 1043~~~~~~~~~~~~~~~~~~~~~~~~ 1044 1045Enum: 137/0x89 1046 1047Description 1048^^^^^^^^^^^ 1049 1050Assigns the transport stream ID of the encoded audio stream 1051 1052Param[0] 1053^^^^^^^^ 1054 1055Audio Stream ID 1056 1057 1058 1059CX2341X_ENC_SET_VIDEO_ID 1060~~~~~~~~~~~~~~~~~~~~~~~~ 1061 1062Enum: 139/0x8B 1063 1064Description 1065^^^^^^^^^^^ 1066 1067Set video transport stream ID 1068 1069Param[0] 1070^^^^^^^^ 1071 1072Video stream ID 1073 1074 1075 1076CX2341X_ENC_SET_PCR_ID 1077~~~~~~~~~~~~~~~~~~~~~~ 1078 1079Enum: 141/0x8D 1080 1081Description 1082^^^^^^^^^^^ 1083 1084Assigns the transport stream ID for PCR packets 1085 1086Param[0] 1087^^^^^^^^ 1088 1089PCR Stream ID 1090 1091 1092 1093CX2341X_ENC_SET_FRAME_RATE 1094~~~~~~~~~~~~~~~~~~~~~~~~~~ 1095 1096Enum: 143/0x8F 1097 1098Description 1099^^^^^^^^^^^ 1100 1101Set video frames per second. Change occurs at start of new GOP. 1102 1103Param[0] 1104^^^^^^^^ 1105 1106- 0=30fps 1107- 1=25fps 1108 1109 1110 1111CX2341X_ENC_SET_FRAME_SIZE 1112~~~~~~~~~~~~~~~~~~~~~~~~~~ 1113 1114Enum: 145/0x91 1115 1116Description 1117^^^^^^^^^^^ 1118 1119Select video stream encoding resolution. 1120 1121Param[0] 1122^^^^^^^^ 1123 1124Height in lines. Default 480 1125 1126Param[1] 1127^^^^^^^^ 1128 1129Width in pixels. Default 720 1130 1131 1132 1133CX2341X_ENC_SET_BIT_RATE 1134~~~~~~~~~~~~~~~~~~~~~~~~ 1135 1136Enum: 149/0x95 1137 1138Description 1139^^^^^^^^^^^ 1140 1141Assign average video stream bitrate. 1142 1143Param[0] 1144^^^^^^^^ 1145 11460=variable bitrate, 1=constant bitrate 1147 1148Param[1] 1149^^^^^^^^ 1150 1151bitrate in bits per second 1152 1153Param[2] 1154^^^^^^^^ 1155 1156peak bitrate in bits per second, divided by 400 1157 1158Param[3] 1159^^^^^^^^ 1160 1161Mux bitrate in bits per second, divided by 400. May be 0 (default). 1162 1163Param[4] 1164^^^^^^^^ 1165 1166Rate Control VBR Padding 1167 1168Param[5] 1169^^^^^^^^ 1170 1171VBV Buffer used by encoder 1172 1173.. note:: 1174 1175 #) Param\[3\] and Param\[4\] seem to be always 0 1176 #) Param\[5\] doesn't seem to be used. 1177 1178 1179 1180CX2341X_ENC_SET_GOP_PROPERTIES 1181~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1182 1183Enum: 151/0x97 1184 1185Description 1186^^^^^^^^^^^ 1187 1188Setup the GOP structure 1189 1190Param[0] 1191^^^^^^^^ 1192 1193GOP size (maximum is 34) 1194 1195Param[1] 1196^^^^^^^^ 1197 1198Number of B frames between the I and P frame, plus 1. 1199For example: IBBPBBPBBPBB --> GOP size: 12, number of B frames: 2+1 = 3 1200 1201.. note:: 1202 1203 GOP size must be a multiple of (B-frames + 1). 1204 1205 1206 1207CX2341X_ENC_SET_ASPECT_RATIO 1208~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1209 1210Enum: 153/0x99 1211 1212Description 1213^^^^^^^^^^^ 1214 1215Sets the encoding aspect ratio. Changes in the aspect ratio take effect 1216at the start of the next GOP. 1217 1218Param[0] 1219^^^^^^^^ 1220 1221- '0000' forbidden 1222- '0001' 1:1 square 1223- '0010' 4:3 1224- '0011' 16:9 1225- '0100' 2.21:1 1226- '0101' to '1111' reserved 1227 1228 1229 1230CX2341X_ENC_SET_DNR_FILTER_MODE 1231~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1232 1233Enum: 155/0x9B 1234 1235Description 1236^^^^^^^^^^^ 1237 1238Assign Dynamic Noise Reduction operating mode 1239 1240Param[0] 1241^^^^^^^^ 1242 1243Bit0: Spatial filter, set=auto, clear=manual 1244Bit1: Temporal filter, set=auto, clear=manual 1245 1246Param[1] 1247^^^^^^^^ 1248 1249Median filter: 1250 1251- 0=Disabled 1252- 1=Horizontal 1253- 2=Vertical 1254- 3=Horiz/Vert 1255- 4=Diagonal 1256 1257 1258 1259CX2341X_ENC_SET_DNR_FILTER_PROPS 1260~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1261 1262Enum: 157/0x9D 1263 1264Description 1265^^^^^^^^^^^ 1266 1267These Dynamic Noise Reduction filter values are only meaningful when 1268the respective filter is set to "manual" (See API 0x9B) 1269 1270Param[0] 1271^^^^^^^^ 1272 1273Spatial filter: default 0, range 0:15 1274 1275Param[1] 1276^^^^^^^^ 1277 1278Temporal filter: default 0, range 0:31 1279 1280 1281 1282CX2341X_ENC_SET_CORING_LEVELS 1283~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1284 1285Enum: 159/0x9F 1286 1287Description 1288^^^^^^^^^^^ 1289 1290Assign Dynamic Noise Reduction median filter properties. 1291 1292Param[0] 1293^^^^^^^^ 1294 1295Threshold above which the luminance median filter is enabled. 1296Default: 0, range 0:255 1297 1298Param[1] 1299^^^^^^^^ 1300 1301Threshold below which the luminance median filter is enabled. 1302Default: 255, range 0:255 1303 1304Param[2] 1305^^^^^^^^ 1306 1307Threshold above which the chrominance median filter is enabled. 1308Default: 0, range 0:255 1309 1310Param[3] 1311^^^^^^^^ 1312 1313Threshold below which the chrominance median filter is enabled. 1314Default: 255, range 0:255 1315 1316 1317 1318CX2341X_ENC_SET_SPATIAL_FILTER_TYPE 1319~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1320 1321Enum: 161/0xA1 1322 1323Description 1324^^^^^^^^^^^ 1325 1326Assign spatial prefilter parameters 1327 1328Param[0] 1329^^^^^^^^ 1330 1331Luminance filter 1332 1333- 0=Off 1334- 1=1D Horizontal 1335- 2=1D Vertical 1336- 3=2D H/V Separable (default) 1337- 4=2D Symmetric non-separable 1338 1339Param[1] 1340^^^^^^^^ 1341 1342Chrominance filter 1343 1344- 0=Off 1345- 1=1D Horizontal (default) 1346 1347 1348 1349CX2341X_ENC_SET_VBI_LINE 1350~~~~~~~~~~~~~~~~~~~~~~~~ 1351 1352Enum: 183/0xB7 1353 1354Description 1355^^^^^^^^^^^ 1356 1357Selects VBI line number. 1358 1359Param[0] 1360^^^^^^^^ 1361 1362- Bits 0:4 line number 1363- Bit 31 0=top_field, 1=bottom_field 1364- Bits 0:31 all set specifies "all lines" 1365 1366Param[1] 1367^^^^^^^^ 1368 1369VBI line information features: 0=disabled, 1=enabled 1370 1371Param[2] 1372^^^^^^^^ 1373 1374Slicing: 0=None, 1=Closed Caption 1375Almost certainly not implemented. Set to 0. 1376 1377Param[3] 1378^^^^^^^^ 1379 1380Luminance samples in this line. 1381Almost certainly not implemented. Set to 0. 1382 1383Param[4] 1384^^^^^^^^ 1385 1386Chrominance samples in this line 1387Almost certainly not implemented. Set to 0. 1388 1389 1390 1391CX2341X_ENC_SET_STREAM_TYPE 1392~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1393 1394Enum: 185/0xB9 1395 1396Description 1397^^^^^^^^^^^ 1398 1399Assign stream type 1400 1401.. note:: 1402 1403 Transport stream is not working in recent firmwares. 1404 And in older firmwares the timestamps in the TS seem to be 1405 unreliable. 1406 1407Param[0] 1408^^^^^^^^ 1409 1410- 0=Program stream 1411- 1=Transport stream 1412- 2=MPEG1 stream 1413- 3=PES A/V stream 1414- 5=PES Video stream 1415- 7=PES Audio stream 1416- 10=DVD stream 1417- 11=VCD stream 1418- 12=SVCD stream 1419- 13=DVD_S1 stream 1420- 14=DVD_S2 stream 1421 1422 1423 1424CX2341X_ENC_SET_OUTPUT_PORT 1425~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1426 1427Enum: 187/0xBB 1428 1429Description 1430^^^^^^^^^^^ 1431 1432Assign stream output port. Normally 0 when the data is copied through 1433the PCI bus (DMA), and 1 when the data is streamed to another chip 1434(pvrusb and cx88-blackbird). 1435 1436Param[0] 1437^^^^^^^^ 1438 1439- 0=Memory (default) 1440- 1=Streaming 1441- 2=Serial 1442 1443Param[1] 1444^^^^^^^^ 1445 1446Unknown, but leaving this to 0 seems to work best. Indications are that 1447this might have to do with USB support, although passing anything but 0 1448only breaks things. 1449 1450 1451 1452CX2341X_ENC_SET_AUDIO_PROPERTIES 1453~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1454 1455Enum: 189/0xBD 1456 1457Description 1458^^^^^^^^^^^ 1459 1460Set audio stream properties, may be called while encoding is in progress. 1461 1462.. note:: 1463 1464 All bitfields are consistent with ISO11172 documentation except 1465 bits 2:3 which ISO docs define as: 1466 1467 - '11' Layer I 1468 - '10' Layer II 1469 - '01' Layer III 1470 - '00' Undefined 1471 1472 This discrepancy may indicate a possible error in the documentation. 1473 Testing indicated that only Layer II is actually working, and that 1474 the minimum bitrate should be 192 kbps. 1475 1476Param[0] 1477^^^^^^^^ 1478 1479Bitmask: 1480 1481.. code-block:: none 1482 1483 0:1 '00' 44.1Khz 1484 '01' 48Khz 1485 '10' 32Khz 1486 '11' reserved 1487 1488 2:3 '01'=Layer I 1489 '10'=Layer II 1490 1491 4:7 Bitrate: 1492 Index | Layer I | Layer II 1493 ------+-------------+------------ 1494 '0000' | free format | free format 1495 '0001' | 32 kbit/s | 32 kbit/s 1496 '0010' | 64 kbit/s | 48 kbit/s 1497 '0011' | 96 kbit/s | 56 kbit/s 1498 '0100' | 128 kbit/s | 64 kbit/s 1499 '0101' | 160 kbit/s | 80 kbit/s 1500 '0110' | 192 kbit/s | 96 kbit/s 1501 '0111' | 224 kbit/s | 112 kbit/s 1502 '1000' | 256 kbit/s | 128 kbit/s 1503 '1001' | 288 kbit/s | 160 kbit/s 1504 '1010' | 320 kbit/s | 192 kbit/s 1505 '1011' | 352 kbit/s | 224 kbit/s 1506 '1100' | 384 kbit/s | 256 kbit/s 1507 '1101' | 416 kbit/s | 320 kbit/s 1508 '1110' | 448 kbit/s | 384 kbit/s 1509 1510 .. note:: 1511 1512 For Layer II, not all combinations of total bitrate 1513 and mode are allowed. See ISO11172-3 3-Annex B, 1514 Table 3-B.2 1515 1516 8:9 '00'=Stereo 1517 '01'=JointStereo 1518 '10'=Dual 1519 '11'=Mono 1520 1521 .. note:: 1522 1523 The cx23415 cannot decode Joint Stereo properly. 1524 1525 10:11 Mode Extension used in joint_stereo mode. 1526 In Layer I and II they indicate which subbands are in 1527 intensity_stereo. All other subbands are coded in stereo. 1528 '00' subbands 4-31 in intensity_stereo, bound==4 1529 '01' subbands 8-31 in intensity_stereo, bound==8 1530 '10' subbands 12-31 in intensity_stereo, bound==12 1531 '11' subbands 16-31 in intensity_stereo, bound==16 1532 1533 12:13 Emphasis: 1534 '00' None 1535 '01' 50/15uS 1536 '10' reserved 1537 '11' CCITT J.17 1538 1539 14 CRC: 1540 '0' off 1541 '1' on 1542 1543 15 Copyright: 1544 '0' off 1545 '1' on 1546 1547 16 Generation: 1548 '0' copy 1549 '1' original 1550 1551 1552 1553CX2341X_ENC_HALT_FW 1554~~~~~~~~~~~~~~~~~~~ 1555 1556Enum: 195/0xC3 1557 1558Description 1559^^^^^^^^^^^ 1560 1561The firmware is halted and no further API calls are serviced until the 1562firmware is uploaded again. 1563 1564 1565 1566CX2341X_ENC_GET_VERSION 1567~~~~~~~~~~~~~~~~~~~~~~~ 1568 1569Enum: 196/0xC4 1570 1571Description 1572^^^^^^^^^^^ 1573 1574Returns the version of the encoder firmware. 1575 1576Result[0] 1577^^^^^^^^^ 1578 1579Version bitmask: 1580- Bits 0:15 build 1581- Bits 16:23 minor 1582- Bits 24:31 major 1583 1584 1585 1586CX2341X_ENC_SET_GOP_CLOSURE 1587~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1588 1589Enum: 197/0xC5 1590 1591Description 1592^^^^^^^^^^^ 1593 1594Assigns the GOP open/close property. 1595 1596Param[0] 1597^^^^^^^^ 1598 1599- 0=Open 1600- 1=Closed 1601 1602 1603 1604CX2341X_ENC_GET_SEQ_END 1605~~~~~~~~~~~~~~~~~~~~~~~ 1606 1607Enum: 198/0xC6 1608 1609Description 1610^^^^^^^^^^^ 1611 1612Obtains the sequence end code of the encoder's buffer. When a capture 1613is started a number of interrupts are still generated, the last of 1614which will have Result[0] set to 1 and Result[1] will contain the size 1615of the buffer. 1616 1617Result[0] 1618^^^^^^^^^ 1619 1620State of the transfer (1 if last buffer) 1621 1622Result[1] 1623^^^^^^^^^ 1624 1625If Result[0] is 1, this contains the size of the last buffer, undefined 1626otherwise. 1627 1628 1629 1630CX2341X_ENC_SET_PGM_INDEX_INFO 1631~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1632 1633Enum: 199/0xC7 1634 1635Description 1636^^^^^^^^^^^ 1637 1638Sets the Program Index Information. 1639The information is stored as follows: 1640 1641.. code-block:: c 1642 1643 struct info { 1644 u32 length; // Length of this frame 1645 u32 offset_low; // Offset in the file of the 1646 u32 offset_high; // start of this frame 1647 u32 mask1; // Bits 0-2 are the type mask: 1648 // 1=I, 2=P, 4=B 1649 // 0=End of Program Index, other fields 1650 // are invalid. 1651 u32 pts; // The PTS of the frame 1652 u32 mask2; // Bit 0 is bit 32 of the pts. 1653 }; 1654 u32 table_ptr; 1655 struct info index[400]; 1656 1657The table_ptr is the encoder memory address in the table were 1658*new* entries will be written. 1659 1660.. note:: This is a ringbuffer, so the table_ptr will wraparound. 1661 1662Param[0] 1663^^^^^^^^ 1664 1665Picture Mask: 1666- 0=No index capture 1667- 1=I frames 1668- 3=I,P frames 1669- 7=I,P,B frames 1670 1671(Seems to be ignored, it always indexes I, P and B frames) 1672 1673Param[1] 1674^^^^^^^^ 1675 1676Elements requested (up to 400) 1677 1678Result[0] 1679^^^^^^^^^ 1680 1681Offset in the encoder memory of the start of the table. 1682 1683Result[1] 1684^^^^^^^^^ 1685 1686Number of allocated elements up to a maximum of Param[1] 1687 1688 1689 1690CX2341X_ENC_SET_VBI_CONFIG 1691~~~~~~~~~~~~~~~~~~~~~~~~~~ 1692 1693Enum: 200/0xC8 1694 1695Description 1696^^^^^^^^^^^ 1697 1698Configure VBI settings 1699 1700Param[0] 1701^^^^^^^^ 1702 1703Bitmap: 1704 1705.. code-block:: none 1706 1707 0 Mode '0' Sliced, '1' Raw 1708 1:3 Insertion: 1709 '000' insert in extension & user data 1710 '001' insert in private packets 1711 '010' separate stream and user data 1712 '111' separate stream and private data 1713 8:15 Stream ID (normally 0xBD) 1714 1715Param[1] 1716^^^^^^^^ 1717 1718Frames per interrupt (max 8). Only valid in raw mode. 1719 1720Param[2] 1721^^^^^^^^ 1722 1723Total raw VBI frames. Only valid in raw mode. 1724 1725Param[3] 1726^^^^^^^^ 1727 1728Start codes 1729 1730Param[4] 1731^^^^^^^^ 1732 1733Stop codes 1734 1735Param[5] 1736^^^^^^^^ 1737 1738Lines per frame 1739 1740Param[6] 1741^^^^^^^^ 1742 1743Byte per line 1744 1745Result[0] 1746^^^^^^^^^ 1747 1748Observed frames per interrupt in raw mode only. Rage 1 to Param[1] 1749 1750Result[1] 1751^^^^^^^^^ 1752 1753Observed number of frames in raw mode. Range 1 to Param[2] 1754 1755Result[2] 1756^^^^^^^^^ 1757 1758Memory offset to start or raw VBI data 1759 1760 1761 1762CX2341X_ENC_SET_DMA_BLOCK_SIZE 1763~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1764 1765Enum: 201/0xC9 1766 1767Description 1768^^^^^^^^^^^ 1769 1770Set DMA transfer block size 1771 1772Param[0] 1773^^^^^^^^ 1774 1775DMA transfer block size in bytes or frames. When unit is bytes, 1776supported block sizes are 2^7, 2^8 and 2^9 bytes. 1777 1778Param[1] 1779^^^^^^^^ 1780 1781Unit: 0=bytes, 1=frames 1782 1783 1784 1785CX2341X_ENC_GET_PREV_DMA_INFO_MB_10 1786~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1787 1788Enum: 202/0xCA 1789 1790Description 1791^^^^^^^^^^^ 1792 1793Returns information on the previous DMA transfer in conjunction with 1794bit 27 of the interrupt mask. Uses mailbox 10. 1795 1796Result[0] 1797^^^^^^^^^ 1798 1799Type of stream 1800 1801Result[1] 1802^^^^^^^^^ 1803 1804Address Offset 1805 1806Result[2] 1807^^^^^^^^^ 1808 1809Maximum size of transfer 1810 1811 1812 1813CX2341X_ENC_GET_PREV_DMA_INFO_MB_9 1814~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1815 1816Enum: 203/0xCB 1817 1818Description 1819^^^^^^^^^^^ 1820 1821Returns information on the previous DMA transfer in conjunction with 1822bit 27 or 18 of the interrupt mask. Uses mailbox 9. 1823 1824Result[0] 1825^^^^^^^^^ 1826 1827Status bits: 1828- 0 read completed 1829- 1 write completed 1830- 2 DMA read error 1831- 3 DMA write error 1832- 4 Scatter-Gather array error 1833 1834Result[1] 1835^^^^^^^^^ 1836 1837DMA type 1838 1839Result[2] 1840^^^^^^^^^ 1841 1842Presentation Time Stamp bits 0..31 1843 1844Result[3] 1845^^^^^^^^^ 1846 1847Presentation Time Stamp bit 32 1848 1849 1850 1851CX2341X_ENC_SCHED_DMA_TO_HOST 1852~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1853 1854Enum: 204/0xCC 1855 1856Description 1857^^^^^^^^^^^ 1858 1859Setup DMA to host operation 1860 1861Param[0] 1862^^^^^^^^ 1863 1864Memory address of link list 1865 1866Param[1] 1867^^^^^^^^ 1868 1869Length of link list (wtf: what units ???) 1870 1871Param[2] 1872^^^^^^^^ 1873 1874DMA type (0=MPEG) 1875 1876 1877 1878CX2341X_ENC_INITIALIZE_INPUT 1879~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1880 1881Enum: 205/0xCD 1882 1883Description 1884^^^^^^^^^^^ 1885 1886Initializes the video input 1887 1888 1889 1890CX2341X_ENC_SET_FRAME_DROP_RATE 1891~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1892 1893Enum: 208/0xD0 1894 1895Description 1896^^^^^^^^^^^ 1897 1898For each frame captured, skip specified number of frames. 1899 1900Param[0] 1901^^^^^^^^ 1902 1903Number of frames to skip 1904 1905 1906 1907CX2341X_ENC_PAUSE_ENCODER 1908~~~~~~~~~~~~~~~~~~~~~~~~~ 1909 1910Enum: 210/0xD2 1911 1912Description 1913^^^^^^^^^^^ 1914 1915During a pause condition, all frames are dropped instead of being encoded. 1916 1917Param[0] 1918^^^^^^^^ 1919 1920- 0=Pause encoding 1921- 1=Continue encoding 1922 1923 1924 1925CX2341X_ENC_REFRESH_INPUT 1926~~~~~~~~~~~~~~~~~~~~~~~~~ 1927 1928Enum: 211/0xD3 1929 1930Description 1931^^^^^^^^^^^ 1932 1933Refreshes the video input 1934 1935 1936 1937CX2341X_ENC_SET_COPYRIGHT 1938~~~~~~~~~~~~~~~~~~~~~~~~~ 1939 1940Enum: 212/0xD4 1941 1942Description 1943^^^^^^^^^^^ 1944 1945Sets stream copyright property 1946 1947Param[0] 1948^^^^^^^^ 1949 1950 1951- 0=Stream is not copyrighted 1952- 1=Stream is copyrighted 1953 1954 1955 1956CX2341X_ENC_SET_EVENT_NOTIFICATION 1957~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1958 1959Enum: 213/0xD5 1960 1961Description 1962^^^^^^^^^^^ 1963 1964Setup firmware to notify the host about a particular event. Host must 1965unmask the interrupt bit. 1966 1967Param[0] 1968^^^^^^^^ 1969 1970Event (0=refresh encoder input) 1971 1972Param[1] 1973^^^^^^^^ 1974 1975Notification 0=disabled 1=enabled 1976 1977Param[2] 1978^^^^^^^^ 1979 1980Interrupt bit 1981 1982Param[3] 1983^^^^^^^^ 1984 1985Mailbox slot, -1 if no mailbox required. 1986 1987 1988 1989CX2341X_ENC_SET_NUM_VSYNC_LINES 1990~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1991 1992Enum: 214/0xD6 1993 1994Description 1995^^^^^^^^^^^ 1996 1997Depending on the analog video decoder used, this assigns the number 1998of lines for field 1 and 2. 1999 2000Param[0] 2001^^^^^^^^ 2002 2003Field 1 number of lines: 2004- 0x00EF for SAA7114 2005- 0x00F0 for SAA7115 2006- 0x0105 for Micronas 2007 2008Param[1] 2009^^^^^^^^ 2010 2011Field 2 number of lines: 2012- 0x00EF for SAA7114 2013- 0x00F0 for SAA7115 2014- 0x0106 for Micronas 2015 2016 2017 2018CX2341X_ENC_SET_PLACEHOLDER 2019~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2020 2021Enum: 215/0xD7 2022 2023Description 2024^^^^^^^^^^^ 2025 2026Provides a mechanism of inserting custom user data in the MPEG stream. 2027 2028Param[0] 2029^^^^^^^^ 2030 2031- 0=extension & user data 2032- 1=private packet with stream ID 0xBD 2033 2034Param[1] 2035^^^^^^^^ 2036 2037Rate at which to insert data, in units of frames (for private packet) 2038or GOPs (for ext. & user data) 2039 2040Param[2] 2041^^^^^^^^ 2042 2043Number of data DWORDs (below) to insert 2044 2045Param[3] 2046^^^^^^^^ 2047 2048Custom data 0 2049 2050Param[4] 2051^^^^^^^^ 2052 2053Custom data 1 2054 2055Param[5] 2056^^^^^^^^ 2057 2058Custom data 2 2059 2060Param[6] 2061^^^^^^^^ 2062 2063Custom data 3 2064 2065Param[7] 2066^^^^^^^^ 2067 2068Custom data 4 2069 2070Param[8] 2071^^^^^^^^ 2072 2073Custom data 5 2074 2075Param[9] 2076^^^^^^^^ 2077 2078Custom data 6 2079 2080Param[10] 2081^^^^^^^^^ 2082 2083Custom data 7 2084 2085Param[11] 2086^^^^^^^^^ 2087 2088Custom data 8 2089 2090 2091 2092CX2341X_ENC_MUTE_VIDEO 2093~~~~~~~~~~~~~~~~~~~~~~ 2094 2095Enum: 217/0xD9 2096 2097Description 2098^^^^^^^^^^^ 2099 2100Video muting 2101 2102Param[0] 2103^^^^^^^^ 2104 2105Bit usage: 2106 2107.. code-block:: none 2108 2109 0 '0'=video not muted 2110 '1'=video muted, creates frames with the YUV color defined below 2111 1:7 Unused 2112 8:15 V chrominance information 2113 16:23 U chrominance information 2114 24:31 Y luminance information 2115 2116 2117 2118CX2341X_ENC_MUTE_AUDIO 2119~~~~~~~~~~~~~~~~~~~~~~ 2120 2121Enum: 218/0xDA 2122 2123Description 2124^^^^^^^^^^^ 2125 2126Audio muting 2127 2128Param[0] 2129^^^^^^^^ 2130 2131- 0=audio not muted 2132- 1=audio muted (produces silent mpeg audio stream) 2133 2134 2135 2136CX2341X_ENC_SET_VERT_CROP_LINE 2137~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2138 2139Enum: 219/0xDB 2140 2141Description 2142^^^^^^^^^^^ 2143 2144Something to do with 'Vertical Crop Line' 2145 2146Param[0] 2147^^^^^^^^ 2148 2149If saa7114 and raw VBI capture and 60 Hz, then set to 10001. 2150Else 0. 2151 2152 2153 2154CX2341X_ENC_MISC 2155~~~~~~~~~~~~~~~~ 2156 2157Enum: 220/0xDC 2158 2159Description 2160^^^^^^^^^^^ 2161 2162Miscellaneous actions. Not known for 100% what it does. It's really a 2163sort of ioctl call. The first parameter is a command number, the second 2164the value. 2165 2166Param[0] 2167^^^^^^^^ 2168 2169Command number: 2170 2171.. code-block:: none 2172 2173 1=set initial SCR value when starting encoding (works). 2174 2=set quality mode (apparently some test setting). 2175 3=setup advanced VIM protection handling. 2176 Always 1 for the cx23416 and 0 for cx23415. 2177 4=generate DVD compatible PTS timestamps 2178 5=USB flush mode 2179 6=something to do with the quantization matrix 2180 7=set navigation pack insertion for DVD: adds 0xbf (private stream 2) 2181 packets to the MPEG. The size of these packets is 2048 bytes (including 2182 the header of 6 bytes: 0x000001bf + length). The payload is zeroed and 2183 it is up to the application to fill them in. These packets are apparently 2184 inserted every four frames. 2185 8=enable scene change detection (seems to be a failure) 2186 9=set history parameters of the video input module 2187 10=set input field order of VIM 2188 11=set quantization matrix 2189 12=reset audio interface after channel change or input switch (has no argument). 2190 Needed for the cx2584x, not needed for the mspx4xx, but it doesn't seem to 2191 do any harm calling it regardless. 2192 13=set audio volume delay 2193 14=set audio delay 2194 2195 2196Param[1] 2197^^^^^^^^ 2198 2199Command value. 2200 2201Decoder firmware API description 2202-------------------------------- 2203 2204.. note:: this API is part of the decoder firmware, so it's cx23415 only. 2205 2206 2207 2208CX2341X_DEC_PING_FW 2209~~~~~~~~~~~~~~~~~~~ 2210 2211Enum: 0/0x00 2212 2213Description 2214^^^^^^^^^^^ 2215 2216This API call does nothing. It may be used to check if the firmware 2217is responding. 2218 2219 2220 2221CX2341X_DEC_START_PLAYBACK 2222~~~~~~~~~~~~~~~~~~~~~~~~~~ 2223 2224Enum: 1/0x01 2225 2226Description 2227^^^^^^^^^^^ 2228 2229Begin or resume playback. 2230 2231Param[0] 2232^^^^^^^^ 2233 22340 based frame number in GOP to begin playback from. 2235 2236Param[1] 2237^^^^^^^^ 2238 2239Specifies the number of muted audio frames to play before normal 2240audio resumes. (This is not implemented in the firmware, leave at 0) 2241 2242 2243 2244CX2341X_DEC_STOP_PLAYBACK 2245~~~~~~~~~~~~~~~~~~~~~~~~~ 2246 2247Enum: 2/0x02 2248 2249Description 2250^^^^^^^^^^^ 2251 2252Ends playback and clears all decoder buffers. If PTS is not zero, 2253playback stops at specified PTS. 2254 2255Param[0] 2256^^^^^^^^ 2257 2258Display 0=last frame, 1=black 2259 2260.. note:: 2261 2262 this takes effect immediately, so if you want to wait for a PTS, 2263 then use '0', otherwise the screen goes to black at once. 2264 You can call this later (even if there is no playback) with a 1 value 2265 to set the screen to black. 2266 2267Param[1] 2268^^^^^^^^ 2269 2270PTS low 2271 2272Param[2] 2273^^^^^^^^ 2274 2275PTS high 2276 2277 2278 2279CX2341X_DEC_SET_PLAYBACK_SPEED 2280~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2281 2282Enum: 3/0x03 2283 2284Description 2285^^^^^^^^^^^ 2286 2287Playback stream at speed other than normal. There are two modes of 2288operation: 2289 2290 - Smooth: host transfers entire stream and firmware drops unused 2291 frames. 2292 - Coarse: host drops frames based on indexing as required to achieve 2293 desired speed. 2294 2295Param[0] 2296^^^^^^^^ 2297 2298.. code-block:: none 2299 2300 Bitmap: 2301 0:7 0 normal 2302 1 fast only "1.5 times" 2303 n nX fast, 1/nX slow 2304 30 Framedrop: 2305 '0' during 1.5 times play, every other B frame is dropped 2306 '1' during 1.5 times play, stream is unchanged (bitrate 2307 must not exceed 8mbps) 2308 31 Speed: 2309 '0' slow 2310 '1' fast 2311 2312.. note:: 2313 2314 n is limited to 2. Anything higher does not result in 2315 faster playback. Instead the host should start dropping frames. 2316 2317Param[1] 2318^^^^^^^^ 2319 2320Direction: 0=forward, 1=reverse 2321 2322.. note:: 2323 2324 to make reverse playback work you have to write full GOPs in 2325 reverse order. 2326 2327Param[2] 2328^^^^^^^^ 2329 2330.. code-block:: none 2331 2332 Picture mask: 2333 1=I frames 2334 3=I, P frames 2335 7=I, P, B frames 2336 2337Param[3] 2338^^^^^^^^ 2339 2340B frames per GOP (for reverse play only) 2341 2342.. note:: 2343 2344 for reverse playback the Picture Mask should be set to I or I, P. 2345 Adding B frames to the mask will result in corrupt video. This field 2346 has to be set to the correct value in order to keep the timing correct. 2347 2348Param[4] 2349^^^^^^^^ 2350 2351Mute audio: 0=disable, 1=enable 2352 2353Param[5] 2354^^^^^^^^ 2355 2356Display 0=frame, 1=field 2357 2358Param[6] 2359^^^^^^^^ 2360 2361Specifies the number of muted audio frames to play before normal audio 2362resumes. (Not implemented in the firmware, leave at 0) 2363 2364 2365 2366CX2341X_DEC_STEP_VIDEO 2367~~~~~~~~~~~~~~~~~~~~~~ 2368 2369Enum: 5/0x05 2370 2371Description 2372^^^^^^^^^^^ 2373 2374Each call to this API steps the playback to the next unit defined below 2375in the current playback direction. 2376 2377Param[0] 2378^^^^^^^^ 2379 23800=frame, 1=top field, 2=bottom field 2381 2382 2383 2384CX2341X_DEC_SET_DMA_BLOCK_SIZE 2385~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2386 2387Enum: 8/0x08 2388 2389Description 2390^^^^^^^^^^^ 2391 2392Set DMA transfer block size. Counterpart to API 0xC9 2393 2394Param[0] 2395^^^^^^^^ 2396 2397DMA transfer block size in bytes. A different size may be specified 2398when issuing the DMA transfer command. 2399 2400 2401 2402CX2341X_DEC_GET_XFER_INFO 2403~~~~~~~~~~~~~~~~~~~~~~~~~ 2404 2405Enum: 9/0x09 2406 2407Description 2408^^^^^^^^^^^ 2409 2410This API call may be used to detect an end of stream condition. 2411 2412Result[0] 2413^^^^^^^^^ 2414 2415Stream type 2416 2417Result[1] 2418^^^^^^^^^ 2419 2420Address offset 2421 2422Result[2] 2423^^^^^^^^^ 2424 2425Maximum bytes to transfer 2426 2427Result[3] 2428^^^^^^^^^ 2429 2430Buffer fullness 2431 2432 2433 2434CX2341X_DEC_GET_DMA_STATUS 2435~~~~~~~~~~~~~~~~~~~~~~~~~~ 2436 2437Enum: 10/0x0A 2438 2439Description 2440^^^^^^^^^^^ 2441 2442Status of the last DMA transfer 2443 2444Result[0] 2445^^^^^^^^^ 2446 2447Bit 1 set means transfer complete 2448Bit 2 set means DMA error 2449Bit 3 set means linked list error 2450 2451Result[1] 2452^^^^^^^^^ 2453 2454DMA type: 0=MPEG, 1=OSD, 2=YUV 2455 2456 2457 2458CX2341X_DEC_SCHED_DMA_FROM_HOST 2459~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2460 2461Enum: 11/0x0B 2462 2463Description 2464^^^^^^^^^^^ 2465 2466Setup DMA from host operation. Counterpart to API 0xCC 2467 2468Param[0] 2469^^^^^^^^ 2470 2471Memory address of link list 2472 2473Param[1] 2474^^^^^^^^ 2475 2476Total # of bytes to transfer 2477 2478Param[2] 2479^^^^^^^^ 2480 2481DMA type (0=MPEG, 1=OSD, 2=YUV) 2482 2483 2484 2485CX2341X_DEC_PAUSE_PLAYBACK 2486~~~~~~~~~~~~~~~~~~~~~~~~~~ 2487 2488Enum: 13/0x0D 2489 2490Description 2491^^^^^^^^^^^ 2492 2493Freeze playback immediately. In this mode, when internal buffers are 2494full, no more data will be accepted and data request IRQs will be 2495masked. 2496 2497Param[0] 2498^^^^^^^^ 2499 2500Display: 0=last frame, 1=black 2501 2502 2503 2504CX2341X_DEC_HALT_FW 2505~~~~~~~~~~~~~~~~~~~ 2506 2507Enum: 14/0x0E 2508 2509Description 2510^^^^^^^^^^^ 2511 2512The firmware is halted and no further API calls are serviced until 2513the firmware is uploaded again. 2514 2515 2516 2517CX2341X_DEC_SET_STANDARD 2518~~~~~~~~~~~~~~~~~~~~~~~~ 2519 2520Enum: 16/0x10 2521 2522Description 2523^^^^^^^^^^^ 2524 2525Selects display standard 2526 2527Param[0] 2528^^^^^^^^ 2529 25300=NTSC, 1=PAL 2531 2532 2533 2534CX2341X_DEC_GET_VERSION 2535~~~~~~~~~~~~~~~~~~~~~~~ 2536 2537Enum: 17/0x11 2538 2539Description 2540^^^^^^^^^^^ 2541 2542Returns decoder firmware version information 2543 2544Result[0] 2545^^^^^^^^^ 2546 2547Version bitmask: 2548 - Bits 0:15 build 2549 - Bits 16:23 minor 2550 - Bits 24:31 major 2551 2552 2553 2554CX2341X_DEC_SET_STREAM_INPUT 2555~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2556 2557Enum: 20/0x14 2558 2559Description 2560^^^^^^^^^^^ 2561 2562Select decoder stream input port 2563 2564Param[0] 2565^^^^^^^^ 2566 25670=memory (default), 1=streaming 2568 2569 2570 2571CX2341X_DEC_GET_TIMING_INFO 2572~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2573 2574Enum: 21/0x15 2575 2576Description 2577^^^^^^^^^^^ 2578 2579Returns timing information from start of playback 2580 2581Result[0] 2582^^^^^^^^^ 2583 2584Frame count by decode order 2585 2586Result[1] 2587^^^^^^^^^ 2588 2589Video PTS bits 0:31 by display order 2590 2591Result[2] 2592^^^^^^^^^ 2593 2594Video PTS bit 32 by display order 2595 2596Result[3] 2597^^^^^^^^^ 2598 2599SCR bits 0:31 by display order 2600 2601Result[4] 2602^^^^^^^^^ 2603 2604SCR bit 32 by display order 2605 2606 2607 2608CX2341X_DEC_SET_AUDIO_MODE 2609~~~~~~~~~~~~~~~~~~~~~~~~~~ 2610 2611Enum: 22/0x16 2612 2613Description 2614^^^^^^^^^^^ 2615 2616Select audio mode 2617 2618Param[0] 2619^^^^^^^^ 2620 2621Dual mono mode action 2622 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged 2623 2624Param[1] 2625^^^^^^^^ 2626 2627Stereo mode action: 2628 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged 2629 2630 2631 2632CX2341X_DEC_SET_EVENT_NOTIFICATION 2633~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2634 2635Enum: 23/0x17 2636 2637Description 2638^^^^^^^^^^^ 2639 2640Setup firmware to notify the host about a particular event. 2641Counterpart to API 0xD5 2642 2643Param[0] 2644^^^^^^^^ 2645 2646Event: 2647 - 0=Audio mode change between mono, (joint) stereo and dual channel. 2648 - 3=Decoder started 2649 - 4=Unknown: goes off 10-15 times per second while decoding. 2650 - 5=Some sync event: goes off once per frame. 2651 2652Param[1] 2653^^^^^^^^ 2654 2655Notification 0=disabled, 1=enabled 2656 2657Param[2] 2658^^^^^^^^ 2659 2660Interrupt bit 2661 2662Param[3] 2663^^^^^^^^ 2664 2665Mailbox slot, -1 if no mailbox required. 2666 2667 2668 2669CX2341X_DEC_SET_DISPLAY_BUFFERS 2670~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2671 2672Enum: 24/0x18 2673 2674Description 2675^^^^^^^^^^^ 2676 2677Number of display buffers. To decode all frames in reverse playback you 2678must use nine buffers. 2679 2680Param[0] 2681^^^^^^^^ 2682 26830=six buffers, 1=nine buffers 2684 2685 2686 2687CX2341X_DEC_EXTRACT_VBI 2688~~~~~~~~~~~~~~~~~~~~~~~ 2689 2690Enum: 25/0x19 2691 2692Description 2693^^^^^^^^^^^ 2694 2695Extracts VBI data 2696 2697Param[0] 2698^^^^^^^^ 2699 27000=extract from extension & user data, 1=extract from private packets 2701 2702Result[0] 2703^^^^^^^^^ 2704 2705VBI table location 2706 2707Result[1] 2708^^^^^^^^^ 2709 2710VBI table size 2711 2712 2713 2714CX2341X_DEC_SET_DECODER_SOURCE 2715~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2716 2717Enum: 26/0x1A 2718 2719Description 2720^^^^^^^^^^^ 2721 2722Selects decoder source. Ensure that the parameters passed to this 2723API match the encoder settings. 2724 2725Param[0] 2726^^^^^^^^ 2727 2728Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host 2729 2730Param[1] 2731^^^^^^^^ 2732 2733YUV picture width 2734 2735Param[2] 2736^^^^^^^^ 2737 2738YUV picture height 2739 2740Param[3] 2741^^^^^^^^ 2742 2743Bitmap: see Param[0] of API 0xBD 2744 2745 2746 2747CX2341X_DEC_SET_PREBUFFERING 2748~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2749 2750Enum: 30/0x1E 2751 2752Description 2753^^^^^^^^^^^ 2754 2755Decoder prebuffering, when enabled up to 128KB are buffered for 2756streams <8mpbs or 640KB for streams >8mbps 2757 2758Param[0] 2759^^^^^^^^ 2760 27610=off, 1=on 2762 2763PVR350 Video decoder registers 0x02002800 -> 0x02002B00 2764------------------------------------------------------- 2765 2766Author: Ian Armstrong <ian@iarmst.demon.co.uk> 2767 2768Version: v0.4 2769 2770Date: 12 March 2007 2771 2772 2773This list has been worked out through trial and error. There will be mistakes 2774and omissions. Some registers have no obvious effect so it's hard to say what 2775they do, while others interact with each other, or require a certain load 2776sequence. Horizontal filter setup is one example, with six registers working 2777in unison and requiring a certain load sequence to correctly configure. The 2778indexed colour palette is much easier to set at just two registers, but again 2779it requires a certain load sequence. 2780 2781Some registers are fussy about what they are set to. Load in a bad value & the 2782decoder will fail. A firmware reload will often recover, but sometimes a reset 2783is required. For registers containing size information, setting them to 0 is 2784generally a bad idea. For other control registers i.e. 2878, you'll only find 2785out what values are bad when it hangs. 2786 2787.. code-block:: none 2788 2789 -------------------------------------------------------------------------------- 2790 2800 2791 bit 0 2792 Decoder enable 2793 0 = disable 2794 1 = enable 2795 -------------------------------------------------------------------------------- 2796 2804 2797 bits 0:31 2798 Decoder horizontal Y alias register 1 2799 --------------- 2800 2808 2801 bits 0:31 2802 Decoder horizontal Y alias register 2 2803 --------------- 2804 280C 2805 bits 0:31 2806 Decoder horizontal Y alias register 3 2807 --------------- 2808 2810 2809 bits 0:31 2810 Decoder horizontal Y alias register 4 2811 --------------- 2812 2814 2813 bits 0:31 2814 Decoder horizontal Y alias register 5 2815 --------------- 2816 2818 2817 bits 0:31 2818 Decoder horizontal Y alias trigger 2819 2820 These six registers control the horizontal aliasing filter for the Y plane. 2821 The first five registers must all be loaded before accessing the trigger 2822 (2818), as this register actually clocks the data through for the first 2823 five. 2824 2825 To correctly program set the filter, this whole procedure must be done 16 2826 times. The actual register contents are copied from a lookup-table in the 2827 firmware which contains 4 different filter settings. 2828 2829 -------------------------------------------------------------------------------- 2830 281C 2831 bits 0:31 2832 Decoder horizontal UV alias register 1 2833 --------------- 2834 2820 2835 bits 0:31 2836 Decoder horizontal UV alias register 2 2837 --------------- 2838 2824 2839 bits 0:31 2840 Decoder horizontal UV alias register 3 2841 --------------- 2842 2828 2843 bits 0:31 2844 Decoder horizontal UV alias register 4 2845 --------------- 2846 282C 2847 bits 0:31 2848 Decoder horizontal UV alias register 5 2849 --------------- 2850 2830 2851 bits 0:31 2852 Decoder horizontal UV alias trigger 2853 2854 These six registers control the horizontal aliasing for the UV plane. 2855 Operation is the same as the Y filter, with 2830 being the trigger 2856 register. 2857 2858 -------------------------------------------------------------------------------- 2859 2834 2860 bits 0:15 2861 Decoder Y source width in pixels 2862 2863 bits 16:31 2864 Decoder Y destination width in pixels 2865 --------------- 2866 2838 2867 bits 0:15 2868 Decoder UV source width in pixels 2869 2870 bits 16:31 2871 Decoder UV destination width in pixels 2872 2873 NOTE: For both registers, the resulting image must be fully visible on 2874 screen. If the image exceeds the right edge both the source and destination 2875 size must be adjusted to reflect the visible portion. For the source width, 2876 you must take into account the scaling when calculating the new value. 2877 -------------------------------------------------------------------------------- 2878 2879 283C 2880 bits 0:31 2881 Decoder Y horizontal scaling 2882 Normally = Reg 2854 >> 2 2883 --------------- 2884 2840 2885 bits 0:31 2886 Decoder ?? unknown - horizontal scaling 2887 Usually 0x00080514 2888 --------------- 2889 2844 2890 bits 0:31 2891 Decoder UV horizontal scaling 2892 Normally = Reg 2854 >> 2 2893 --------------- 2894 2848 2895 bits 0:31 2896 Decoder ?? unknown - horizontal scaling 2897 Usually 0x00100514 2898 --------------- 2899 284C 2900 bits 0:31 2901 Decoder ?? unknown - Y plane 2902 Usually 0x00200020 2903 --------------- 2904 2850 2905 bits 0:31 2906 Decoder ?? unknown - UV plane 2907 Usually 0x00200020 2908 --------------- 2909 2854 2910 bits 0:31 2911 Decoder 'master' value for horizontal scaling 2912 --------------- 2913 2858 2914 bits 0:31 2915 Decoder ?? unknown 2916 Usually 0 2917 --------------- 2918 285C 2919 bits 0:31 2920 Decoder ?? unknown 2921 Normally = Reg 2854 >> 1 2922 --------------- 2923 2860 2924 bits 0:31 2925 Decoder ?? unknown 2926 Usually 0 2927 --------------- 2928 2864 2929 bits 0:31 2930 Decoder ?? unknown 2931 Normally = Reg 2854 >> 1 2932 --------------- 2933 2868 2934 bits 0:31 2935 Decoder ?? unknown 2936 Usually 0 2937 2938 Most of these registers either control horizontal scaling, or appear linked 2939 to it in some way. Register 2854 contains the 'master' value & the other 2940 registers can be calculated from that one. You must also remember to 2941 correctly set the divider in Reg 2874. 2942 2943 To enlarge: 2944 Reg 2854 = (source_width * 0x00200000) / destination_width 2945 Reg 2874 = No divide 2946 2947 To reduce from full size down to half size: 2948 Reg 2854 = (source_width/2 * 0x00200000) / destination width 2949 Reg 2874 = Divide by 2 2950 2951 To reduce from half size down to quarter size: 2952 Reg 2854 = (source_width/4 * 0x00200000) / destination width 2953 Reg 2874 = Divide by 4 2954 2955 The result is always rounded up. 2956 2957 -------------------------------------------------------------------------------- 2958 286C 2959 bits 0:15 2960 Decoder horizontal Y buffer offset 2961 2962 bits 15:31 2963 Decoder horizontal UV buffer offset 2964 2965 Offset into the video image buffer. If the offset is gradually incremented, 2966 the on screen image will move left & wrap around higher up on the right. 2967 2968 -------------------------------------------------------------------------------- 2969 2870 2970 bits 0:15 2971 Decoder horizontal Y output offset 2972 2973 bits 16:31 2974 Decoder horizontal UV output offset 2975 2976 Offsets the actual video output. Controls output alignment of the Y & UV 2977 planes. The higher the value, the greater the shift to the left. Use 2978 reg 2890 to move the image right. 2979 2980 -------------------------------------------------------------------------------- 2981 2874 2982 bits 0:1 2983 Decoder horizontal Y output size divider 2984 00 = No divide 2985 01 = Divide by 2 2986 10 = Divide by 3 2987 2988 bits 4:5 2989 Decoder horizontal UV output size divider 2990 00 = No divide 2991 01 = Divide by 2 2992 10 = Divide by 3 2993 2994 bit 8 2995 Decoder ?? unknown 2996 0 = Normal 2997 1 = Affects video output levels 2998 2999 bit 16 3000 Decoder ?? unknown 3001 0 = Normal 3002 1 = Disable horizontal filter 3003 3004 -------------------------------------------------------------------------------- 3005 2878 3006 bit 0 3007 ?? unknown 3008 3009 bit 1 3010 osd on/off 3011 0 = osd off 3012 1 = osd on 3013 3014 bit 2 3015 Decoder + osd video timing 3016 0 = NTSC 3017 1 = PAL 3018 3019 bits 3:4 3020 ?? unknown 3021 3022 bit 5 3023 Decoder + osd 3024 Swaps upper & lower fields 3025 3026 -------------------------------------------------------------------------------- 3027 287C 3028 bits 0:10 3029 Decoder & osd ?? unknown 3030 Moves entire screen horizontally. Starts at 0x005 with the screen 3031 shifted heavily to the right. Incrementing in steps of 0x004 will 3032 gradually shift the screen to the left. 3033 3034 bits 11:31 3035 ?? unknown 3036 3037 Normally contents are 0x00101111 (NTSC) or 0x1010111d (PAL) 3038 3039 -------------------------------------------------------------------------------- 3040 2880 -------- ?? unknown 3041 2884 -------- ?? unknown 3042 -------------------------------------------------------------------------------- 3043 2888 3044 bit 0 3045 Decoder + osd ?? unknown 3046 0 = Normal 3047 1 = Misaligned fields (Correctable through 289C & 28A4) 3048 3049 bit 4 3050 ?? unknown 3051 3052 bit 8 3053 ?? unknown 3054 3055 Warning: Bad values will require a firmware reload to recover. 3056 Known to be bad are 0x000,0x011,0x100,0x111 3057 -------------------------------------------------------------------------------- 3058 288C 3059 bits 0:15 3060 osd ?? unknown 3061 Appears to affect the osd position stability. The higher the value the 3062 more unstable it becomes. Decoder output remains stable. 3063 3064 bits 16:31 3065 osd ?? unknown 3066 Same as bits 0:15 3067 3068 -------------------------------------------------------------------------------- 3069 2890 3070 bits 0:11 3071 Decoder output horizontal offset. 3072 3073 Horizontal offset moves the video image right. A small left shift is 3074 possible, but it's better to use reg 2870 for that due to its greater 3075 range. 3076 3077 NOTE: Video corruption will occur if video window is shifted off the right 3078 edge. To avoid this read the notes for 2834 & 2838. 3079 -------------------------------------------------------------------------------- 3080 2894 3081 bits 0:23 3082 Decoder output video surround colour. 3083 3084 Contains the colour (in yuv) used to fill the screen when the video is 3085 running in a window. 3086 -------------------------------------------------------------------------------- 3087 2898 3088 bits 0:23 3089 Decoder video window colour 3090 Contains the colour (in yuv) used to fill the video window when the 3091 video is turned off. 3092 3093 bit 24 3094 Decoder video output 3095 0 = Video on 3096 1 = Video off 3097 3098 bit 28 3099 Decoder plane order 3100 0 = Y,UV 3101 1 = UV,Y 3102 3103 bit 29 3104 Decoder second plane byte order 3105 0 = Normal (UV) 3106 1 = Swapped (VU) 3107 3108 In normal usage, the first plane is Y & the second plane is UV. Though the 3109 order of the planes can be swapped, only the byte order of the second plane 3110 can be swapped. This isn't much use for the Y plane, but can be useful for 3111 the UV plane. 3112 3113 -------------------------------------------------------------------------------- 3114 289C 3115 bits 0:15 3116 Decoder vertical field offset 1 3117 3118 bits 16:31 3119 Decoder vertical field offset 2 3120 3121 Controls field output vertical alignment. The higher the number, the lower 3122 the image on screen. Known starting values are 0x011E0017 (NTSC) & 3123 0x01500017 (PAL) 3124 -------------------------------------------------------------------------------- 3125 28A0 3126 bits 0:15 3127 Decoder & osd width in pixels 3128 3129 bits 16:31 3130 Decoder & osd height in pixels 3131 3132 All output from the decoder & osd are disabled beyond this area. Decoder 3133 output will simply go black outside of this region. If the osd tries to 3134 exceed this area it will become corrupt. 3135 -------------------------------------------------------------------------------- 3136 28A4 3137 bits 0:11 3138 osd left shift. 3139 3140 Has a range of 0x770->0x7FF. With the exception of 0, any value outside of 3141 this range corrupts the osd. 3142 -------------------------------------------------------------------------------- 3143 28A8 3144 bits 0:15 3145 osd vertical field offset 1 3146 3147 bits 16:31 3148 osd vertical field offset 2 3149 3150 Controls field output vertical alignment. The higher the number, the lower 3151 the image on screen. Known starting values are 0x011E0017 (NTSC) & 3152 0x01500017 (PAL) 3153 -------------------------------------------------------------------------------- 3154 28AC -------- ?? unknown 3155 | 3156 V 3157 28BC -------- ?? unknown 3158 -------------------------------------------------------------------------------- 3159 28C0 3160 bit 0 3161 Current output field 3162 0 = first field 3163 1 = second field 3164 3165 bits 16:31 3166 Current scanline 3167 The scanline counts from the top line of the first field 3168 through to the last line of the second field. 3169 -------------------------------------------------------------------------------- 3170 28C4 -------- ?? unknown 3171 | 3172 V 3173 28F8 -------- ?? unknown 3174 -------------------------------------------------------------------------------- 3175 28FC 3176 bit 0 3177 ?? unknown 3178 0 = Normal 3179 1 = Breaks decoder & osd output 3180 -------------------------------------------------------------------------------- 3181 2900 3182 bits 0:31 3183 Decoder vertical Y alias register 1 3184 --------------- 3185 2904 3186 bits 0:31 3187 Decoder vertical Y alias register 2 3188 --------------- 3189 2908 3190 bits 0:31 3191 Decoder vertical Y alias trigger 3192 3193 These three registers control the vertical aliasing filter for the Y plane. 3194 Operation is similar to the horizontal Y filter (2804). The only real 3195 difference is that there are only two registers to set before accessing 3196 the trigger register (2908). As for the horizontal filter, the values are 3197 taken from a lookup table in the firmware, and the procedure must be 3198 repeated 16 times to fully program the filter. 3199 -------------------------------------------------------------------------------- 3200 290C 3201 bits 0:31 3202 Decoder vertical UV alias register 1 3203 --------------- 3204 2910 3205 bits 0:31 3206 Decoder vertical UV alias register 2 3207 --------------- 3208 2914 3209 bits 0:31 3210 Decoder vertical UV alias trigger 3211 3212 These three registers control the vertical aliasing filter for the UV 3213 plane. Operation is the same as the Y filter, with 2914 being the trigger. 3214 -------------------------------------------------------------------------------- 3215 2918 3216 bits 0:15 3217 Decoder Y source height in pixels 3218 3219 bits 16:31 3220 Decoder Y destination height in pixels 3221 --------------- 3222 291C 3223 bits 0:15 3224 Decoder UV source height in pixels divided by 2 3225 3226 bits 16:31 3227 Decoder UV destination height in pixels 3228 3229 NOTE: For both registers, the resulting image must be fully visible on 3230 screen. If the image exceeds the bottom edge both the source and 3231 destination size must be adjusted to reflect the visible portion. For the 3232 source height, you must take into account the scaling when calculating the 3233 new value. 3234 -------------------------------------------------------------------------------- 3235 2920 3236 bits 0:31 3237 Decoder Y vertical scaling 3238 Normally = Reg 2930 >> 2 3239 --------------- 3240 2924 3241 bits 0:31 3242 Decoder Y vertical scaling 3243 Normally = Reg 2920 + 0x514 3244 --------------- 3245 2928 3246 bits 0:31 3247 Decoder UV vertical scaling 3248 When enlarging = Reg 2930 >> 2 3249 When reducing = Reg 2930 >> 3 3250 --------------- 3251 292C 3252 bits 0:31 3253 Decoder UV vertical scaling 3254 Normally = Reg 2928 + 0x514 3255 --------------- 3256 2930 3257 bits 0:31 3258 Decoder 'master' value for vertical scaling 3259 --------------- 3260 2934 3261 bits 0:31 3262 Decoder ?? unknown - Y vertical scaling 3263 --------------- 3264 2938 3265 bits 0:31 3266 Decoder Y vertical scaling 3267 Normally = Reg 2930 3268 --------------- 3269 293C 3270 bits 0:31 3271 Decoder ?? unknown - Y vertical scaling 3272 --------------- 3273 2940 3274 bits 0:31 3275 Decoder UV vertical scaling 3276 When enlarging = Reg 2930 >> 1 3277 When reducing = Reg 2930 3278 --------------- 3279 2944 3280 bits 0:31 3281 Decoder ?? unknown - UV vertical scaling 3282 --------------- 3283 2948 3284 bits 0:31 3285 Decoder UV vertical scaling 3286 Normally = Reg 2940 3287 --------------- 3288 294C 3289 bits 0:31 3290 Decoder ?? unknown - UV vertical scaling 3291 3292 Most of these registers either control vertical scaling, or appear linked 3293 to it in some way. Register 2930 contains the 'master' value & all other 3294 registers can be calculated from that one. You must also remember to 3295 correctly set the divider in Reg 296C 3296 3297 To enlarge: 3298 Reg 2930 = (source_height * 0x00200000) / destination_height 3299 Reg 296C = No divide 3300 3301 To reduce from full size down to half size: 3302 Reg 2930 = (source_height/2 * 0x00200000) / destination height 3303 Reg 296C = Divide by 2 3304 3305 To reduce from half down to quarter. 3306 Reg 2930 = (source_height/4 * 0x00200000) / destination height 3307 Reg 296C = Divide by 4 3308 3309 -------------------------------------------------------------------------------- 3310 2950 3311 bits 0:15 3312 Decoder Y line index into display buffer, first field 3313 3314 bits 16:31 3315 Decoder Y vertical line skip, first field 3316 -------------------------------------------------------------------------------- 3317 2954 3318 bits 0:15 3319 Decoder Y line index into display buffer, second field 3320 3321 bits 16:31 3322 Decoder Y vertical line skip, second field 3323 -------------------------------------------------------------------------------- 3324 2958 3325 bits 0:15 3326 Decoder UV line index into display buffer, first field 3327 3328 bits 16:31 3329 Decoder UV vertical line skip, first field 3330 -------------------------------------------------------------------------------- 3331 295C 3332 bits 0:15 3333 Decoder UV line index into display buffer, second field 3334 3335 bits 16:31 3336 Decoder UV vertical line skip, second field 3337 -------------------------------------------------------------------------------- 3338 2960 3339 bits 0:15 3340 Decoder destination height minus 1 3341 3342 bits 16:31 3343 Decoder destination height divided by 2 3344 -------------------------------------------------------------------------------- 3345 2964 3346 bits 0:15 3347 Decoder Y vertical offset, second field 3348 3349 bits 16:31 3350 Decoder Y vertical offset, first field 3351 3352 These two registers shift the Y plane up. The higher the number, the 3353 greater the shift. 3354 -------------------------------------------------------------------------------- 3355 2968 3356 bits 0:15 3357 Decoder UV vertical offset, second field 3358 3359 bits 16:31 3360 Decoder UV vertical offset, first field 3361 3362 These two registers shift the UV plane up. The higher the number, the 3363 greater the shift. 3364 -------------------------------------------------------------------------------- 3365 296C 3366 bits 0:1 3367 Decoder vertical Y output size divider 3368 00 = No divide 3369 01 = Divide by 2 3370 10 = Divide by 4 3371 3372 bits 8:9 3373 Decoder vertical UV output size divider 3374 00 = No divide 3375 01 = Divide by 2 3376 10 = Divide by 4 3377 -------------------------------------------------------------------------------- 3378 2970 3379 bit 0 3380 Decoder ?? unknown 3381 0 = Normal 3382 1 = Affect video output levels 3383 3384 bit 16 3385 Decoder ?? unknown 3386 0 = Normal 3387 1 = Disable vertical filter 3388 3389 -------------------------------------------------------------------------------- 3390 2974 -------- ?? unknown 3391 | 3392 V 3393 29EF -------- ?? unknown 3394 -------------------------------------------------------------------------------- 3395 2A00 3396 bits 0:2 3397 osd colour mode 3398 000 = 8 bit indexed 3399 001 = 16 bit (565) 3400 010 = 15 bit (555) 3401 011 = 12 bit (444) 3402 100 = 32 bit (8888) 3403 3404 bits 4:5 3405 osd display bpp 3406 01 = 8 bit 3407 10 = 16 bit 3408 11 = 32 bit 3409 3410 bit 8 3411 osd global alpha 3412 0 = Off 3413 1 = On 3414 3415 bit 9 3416 osd local alpha 3417 0 = Off 3418 1 = On 3419 3420 bit 10 3421 osd colour key 3422 0 = Off 3423 1 = On 3424 3425 bit 11 3426 osd ?? unknown 3427 Must be 1 3428 3429 bit 13 3430 osd colour space 3431 0 = ARGB 3432 1 = AYVU 3433 3434 bits 16:31 3435 osd ?? unknown 3436 Must be 0x001B (some kind of buffer pointer ?) 3437 3438 When the bits-per-pixel is set to 8, the colour mode is ignored and 3439 assumed to be 8 bit indexed. For 16 & 32 bits-per-pixel the colour depth 3440 is honoured, and when using a colour depth that requires fewer bytes than 3441 allocated the extra bytes are used as padding. So for a 32 bpp with 8 bit 3442 index colour, there are 3 padding bytes per pixel. It's also possible to 3443 select 16bpp with a 32 bit colour mode. This results in the pixel width 3444 being doubled, but the color key will not work as expected in this mode. 3445 3446 Colour key is as it suggests. You designate a colour which will become 3447 completely transparent. When using 565, 555 or 444 colour modes, the 3448 colour key is always 16 bits wide. The colour to key on is set in Reg 2A18. 3449 3450 Local alpha works differently depending on the colour mode. For 32bpp & 8 3451 bit indexed, local alpha is a per-pixel 256 step transparency, with 0 being 3452 transparent and 255 being solid. For the 16bpp modes 555 & 444, the unused 3453 bit(s) act as a simple transparency switch, with 0 being solid & 1 being 3454 fully transparent. There is no local alpha support for 16bit 565. 3455 3456 Global alpha is a 256 step transparency that applies to the entire osd, 3457 with 0 being transparent & 255 being solid. 3458 3459 It's possible to combine colour key, local alpha & global alpha. 3460 -------------------------------------------------------------------------------- 3461 2A04 3462 bits 0:15 3463 osd x coord for left edge 3464 3465 bits 16:31 3466 osd y coord for top edge 3467 --------------- 3468 2A08 3469 bits 0:15 3470 osd x coord for right edge 3471 3472 bits 16:31 3473 osd y coord for bottom edge 3474 3475 For both registers, (0,0) = top left corner of the display area. These 3476 registers do not control the osd size, only where it's positioned & how 3477 much is visible. The visible osd area cannot exceed the right edge of the 3478 display, otherwise the osd will become corrupt. See reg 2A10 for 3479 setting osd width. 3480 -------------------------------------------------------------------------------- 3481 2A0C 3482 bits 0:31 3483 osd buffer index 3484 3485 An index into the osd buffer. Slowly incrementing this moves the osd left, 3486 wrapping around onto the right edge 3487 -------------------------------------------------------------------------------- 3488 2A10 3489 bits 0:11 3490 osd buffer 32 bit word width 3491 3492 Contains the width of the osd measured in 32 bit words. This means that all 3493 colour modes are restricted to a byte width which is divisible by 4. 3494 -------------------------------------------------------------------------------- 3495 2A14 3496 bits 0:15 3497 osd height in pixels 3498 3499 bits 16:32 3500 osd line index into buffer 3501 osd will start displaying from this line. 3502 -------------------------------------------------------------------------------- 3503 2A18 3504 bits 0:31 3505 osd colour key 3506 3507 Contains the colour value which will be transparent. 3508 -------------------------------------------------------------------------------- 3509 2A1C 3510 bits 0:7 3511 osd global alpha 3512 3513 Contains the global alpha value (equiv ivtvfbctl --alpha XX) 3514 -------------------------------------------------------------------------------- 3515 2A20 -------- ?? unknown 3516 | 3517 V 3518 2A2C -------- ?? unknown 3519 -------------------------------------------------------------------------------- 3520 2A30 3521 bits 0:7 3522 osd colour to change in indexed palette 3523 --------------- 3524 2A34 3525 bits 0:31 3526 osd colour for indexed palette 3527 3528 To set the new palette, first load the index of the colour to change into 3529 2A30, then load the new colour into 2A34. The full palette is 256 colours, 3530 so the index range is 0x00-0xFF 3531 -------------------------------------------------------------------------------- 3532 2A38 -------- ?? unknown 3533 2A3C -------- ?? unknown 3534 -------------------------------------------------------------------------------- 3535 2A40 3536 bits 0:31 3537 osd ?? unknown 3538 3539 Affects overall brightness, wrapping around to black 3540 -------------------------------------------------------------------------------- 3541 2A44 3542 bits 0:31 3543 osd ?? unknown 3544 3545 Green tint 3546 -------------------------------------------------------------------------------- 3547 2A48 3548 bits 0:31 3549 osd ?? unknown 3550 3551 Red tint 3552 -------------------------------------------------------------------------------- 3553 2A4C 3554 bits 0:31 3555 osd ?? unknown 3556 3557 Affects overall brightness, wrapping around to black 3558 -------------------------------------------------------------------------------- 3559 2A50 3560 bits 0:31 3561 osd ?? unknown 3562 3563 Colour shift 3564 -------------------------------------------------------------------------------- 3565 2A54 3566 bits 0:31 3567 osd ?? unknown 3568 3569 Colour shift 3570 -------------------------------------------------------------------------------- 3571 2A58 -------- ?? unknown 3572 | 3573 V 3574 2AFC -------- ?? unknown 3575 -------------------------------------------------------------------------------- 3576 2B00 3577 bit 0 3578 osd filter control 3579 0 = filter off 3580 1 = filter on 3581 3582 bits 1:4 3583 osd ?? unknown 3584 3585 -------------------------------------------------------------------------------- 3586 3587The cx231xx DMA engine 3588---------------------- 3589 3590 3591This page describes the structures and procedures used by the cx2341x DMA 3592engine. 3593 3594Introduction 3595~~~~~~~~~~~~ 3596 3597The cx2341x PCI interface is busmaster capable. This means it has a DMA 3598engine to efficiently transfer large volumes of data between the card and main 3599memory without requiring help from a CPU. Like most hardware, it must operate 3600on contiguous physical memory. This is difficult to come by in large quantities 3601on virtual memory machines. 3602 3603Therefore, it also supports a technique called "scatter-gather". The card can 3604transfer multiple buffers in one operation. Instead of allocating one large 3605contiguous buffer, the driver can allocate several smaller buffers. 3606 3607In practice, I've seen the average transfer to be roughly 80K, but transfers 3608above 128K were not uncommon, particularly at startup. The 128K figure is 3609important, because that is the largest block that the kernel can normally 3610allocate. Even still, 128K blocks are hard to come by, so the driver writer is 3611urged to choose a smaller block size and learn the scatter-gather technique. 3612 3613Mailbox #10 is reserved for DMA transfer information. 3614 3615Note: the hardware expects little-endian data ('intel format'). 3616 3617Flow 3618~~~~ 3619 3620This section describes, in general, the order of events when handling DMA 3621transfers. Detailed information follows this section. 3622 3623- The card raises the Encoder interrupt. 3624- The driver reads the transfer type, offset and size from Mailbox #10. 3625- The driver constructs the scatter-gather array from enough free dma buffers 3626 to cover the size. 3627- The driver schedules the DMA transfer via the ScheduleDMAtoHost API call. 3628- The card raises the DMA Complete interrupt. 3629- The driver checks the DMA status register for any errors. 3630- The driver post-processes the newly transferred buffers. 3631 3632NOTE! It is possible that the Encoder and DMA Complete interrupts get raised 3633simultaneously. (End of the last, start of the next, etc.) 3634 3635Mailbox #10 3636~~~~~~~~~~~ 3637 3638The Flags, Command, Return Value and Timeout fields are ignored. 3639 3640- Name: Mailbox #10 3641- Results[0]: Type: 0: MPEG. 3642- Results[1]: Offset: The position relative to the card's memory space. 3643- Results[2]: Size: The exact number of bytes to transfer. 3644 3645My speculation is that since the StartCapture API has a capture type of "RAW" 3646available, that the type field will have other values that correspond to YUV 3647and PCM data. 3648 3649Scatter-Gather Array 3650~~~~~~~~~~~~~~~~~~~~ 3651 3652The scatter-gather array is a contiguously allocated block of memory that 3653tells the card the source and destination of each data-block to transfer. 3654Card "addresses" are derived from the offset supplied by Mailbox #10. Host 3655addresses are the physical memory location of the target DMA buffer. 3656 3657Each S-G array element is a struct of three 32-bit words. The first word is 3658the source address, the second is the destination address. Both take up the 3659entire 32 bits. The lowest 18 bits of the third word is the transfer byte 3660count. The high-bit of the third word is the "last" flag. The last-flag tells 3661the card to raise the DMA_DONE interrupt. From hard personal experience, if 3662you forget to set this bit, the card will still "work" but the stream will 3663most likely get corrupted. 3664 3665The transfer count must be a multiple of 256. Therefore, the driver will need 3666to track how much data in the target buffer is valid and deal with it 3667accordingly. 3668 3669Array Element: 3670 3671- 32-bit Source Address 3672- 32-bit Destination Address 3673- 14-bit reserved (high bit is the last flag) 3674- 18-bit byte count 3675 3676DMA Transfer Status 3677~~~~~~~~~~~~~~~~~~~ 3678 3679Register 0x0004 holds the DMA Transfer Status: 3680 3681- bit 0: read completed 3682- bit 1: write completed 3683- bit 2: DMA read error 3684- bit 3: DMA write error 3685- bit 4: Scatter-Gather array error