spear-pcie-gadget.rst (4440B)
1.. SPDX-License-Identifier: GPL-2.0 2 3======================== 4Spear PCIe Gadget Driver 5======================== 6 7Author 8====== 9Pratyush Anand (pratyush.anand@gmail.com) 10 11Location 12======== 13driver/misc/spear13xx_pcie_gadget.c 14 15Supported Chip: 16=============== 17SPEAr1300 18SPEAr1310 19 20Menuconfig option: 21================== 22Device Drivers 23 Misc devices 24 PCIe gadget support for SPEAr13XX platform 25 26purpose 27======= 28This driver has several nodes which can be read/written by configfs interface. 29Its main purpose is to configure selected dual mode PCIe controller as device 30and then program its various registers to configure it as a particular device 31type. This driver can be used to show spear's PCIe device capability. 32 33Description of different nodes: 34=============================== 35 36read behavior of nodes: 37----------------------- 38 39=============== ============================================================== 40link gives ltssm status. 41int_type type of supported interrupt 42no_of_msi zero if MSI is not enabled by host. A positive value is the 43 number of MSI vector granted. 44vendor_id returns programmed vendor id (hex) 45device_id returns programmed device id(hex) 46bar0_size: returns size of bar0 in hex. 47bar0_address returns address of bar0 mapped area in hex. 48bar0_rw_offset returns offset of bar0 for which bar0_data will return value. 49bar0_data returns data at bar0_rw_offset. 50=============== ============================================================== 51 52write behavior of nodes: 53------------------------ 54 55=============== ================================================================ 56link write UP to enable ltsmm DOWN to disable 57int_type write interrupt type to be configured and (int_type could be 58 INTA, MSI or NO_INT). Select MSI only when you have programmed 59 no_of_msi node. 60no_of_msi number of MSI vector needed. 61inta write 1 to assert INTA and 0 to de-assert. 62send_msi write MSI vector to be sent. 63vendor_id write vendor id(hex) to be programmed. 64device_id write device id(hex) to be programmed. 65bar0_size write size of bar0 in hex. default bar0 size is 1000 (hex) 66 bytes. 67bar0_address write address of bar0 mapped area in hex. (default mapping of 68 bar0 is SYSRAM1(E0800000). Always program bar size before bar 69 address. Kernel might modify bar size and address for alignment, 70 so read back bar size and address after writing to cross check. 71bar0_rw_offset write offset of bar0 for which bar0_data will write value. 72bar0_data write data to be written at bar0_rw_offset. 73=============== ================================================================ 74 75Node programming example 76======================== 77 78Program all PCIe registers in such a way that when this device is connected 79to the PCIe host, then host sees this device as 1MB RAM. 80 81:: 82 83 #mount -t configfs none /Config 84 85For nth PCIe Device Controller:: 86 87 # cd /config/pcie_gadget.n/ 88 89Now you have all the nodes in this directory. 90program vendor id as 0x104a:: 91 92 # echo 104A >> vendor_id 93 94program device id as 0xCD80:: 95 96 # echo CD80 >> device_id 97 98program BAR0 size as 1MB:: 99 100 # echo 100000 >> bar0_size 101 102check for programmed bar0 size:: 103 104 # cat bar0_size 105 106Program BAR0 Address as DDR (0x2100000). This is the physical address of 107memory, which is to be made visible to PCIe host. Similarly any other peripheral 108can also be made visible to PCIe host. E.g., if you program base address of UART 109as BAR0 address then when this device will be connected to a host, it will be 110visible as UART. 111 112:: 113 114 # echo 2100000 >> bar0_address 115 116program interrupt type : INTA:: 117 118 # echo INTA >> int_type 119 120go for link up now:: 121 122 # echo UP >> link 123 124It will have to be insured that, once link up is done on gadget, then only host 125is initialized and start to search PCIe devices on its port. 126 127:: 128 129 /*wait till link is up*/ 130 # cat link 131 132Wait till it returns UP. 133 134To assert INTA:: 135 136 # echo 1 >> inta 137 138To de-assert INTA:: 139 140 # echo 0 >> inta 141 142if MSI is to be used as interrupt, program no of msi vector needed (say4):: 143 144 # echo 4 >> no_of_msi 145 146select MSI as interrupt type:: 147 148 # echo MSI >> int_type 149 150go for link up now:: 151 152 # echo UP >> link 153 154wait till link is up:: 155 156 # cat link 157 158An application can repetitively read this node till link is found UP. It can 159sleep between two read. 160 161wait till msi is enabled:: 162 163 # cat no_of_msi 164 165Should return 4 (number of requested MSI vector) 166 167to send msi vector 2:: 168 169 # echo 2 >> send_msi 170 # cd -