arcnet-hardware.rst (109541B)
1.. SPDX-License-Identifier: GPL-2.0 2 3=============== 4ARCnet Hardware 5=============== 6 7.. note:: 8 9 1) This file is a supplement to arcnet.txt. Please read that for general 10 driver configuration help. 11 2) This file is no longer Linux-specific. It should probably be moved out 12 of the kernel sources. Ideas? 13 14Because so many people (myself included) seem to have obtained ARCnet cards 15without manuals, this file contains a quick introduction to ARCnet hardware, 16some cabling tips, and a listing of all jumper settings I can find. Please 17e-mail apenwarr@worldvisions.ca with any settings for your particular card, 18or any other information you have! 19 20 21Introduction to ARCnet 22====================== 23 24ARCnet is a network type which works in a way similar to popular Ethernet 25networks but which is also different in some very important ways. 26 27First of all, you can get ARCnet cards in at least two speeds: 2.5 Mbps 28(slower than Ethernet) and 100 Mbps (faster than normal Ethernet). In fact, 29there are others as well, but these are less common. The different hardware 30types, as far as I'm aware, are not compatible and so you cannot wire a 31100 Mbps card to a 2.5 Mbps card, and so on. From what I hear, my driver does 32work with 100 Mbps cards, but I haven't been able to verify this myself, 33since I only have the 2.5 Mbps variety. It is probably not going to saturate 34your 100 Mbps card. Stop complaining. :) 35 36You also cannot connect an ARCnet card to any kind of Ethernet card and 37expect it to work. 38 39There are two "types" of ARCnet - STAR topology and BUS topology. This 40refers to how the cards are meant to be wired together. According to most 41available documentation, you can only connect STAR cards to STAR cards and 42BUS cards to BUS cards. That makes sense, right? Well, it's not quite 43true; see below under "Cabling." 44 45Once you get past these little stumbling blocks, ARCnet is actually quite a 46well-designed standard. It uses something called "modified token passing" 47which makes it completely incompatible with so-called "Token Ring" cards, 48but which makes transfers much more reliable than Ethernet does. In fact, 49ARCnet will guarantee that a packet arrives safely at the destination, and 50even if it can't possibly be delivered properly (ie. because of a cable 51break, or because the destination computer does not exist) it will at least 52tell the sender about it. 53 54Because of the carefully defined action of the "token", it will always make 55a pass around the "ring" within a maximum length of time. This makes it 56useful for realtime networks. 57 58In addition, all known ARCnet cards have an (almost) identical programming 59interface. This means that with one ARCnet driver you can support any 60card, whereas with Ethernet each manufacturer uses what is sometimes a 61completely different programming interface, leading to a lot of different, 62sometimes very similar, Ethernet drivers. Of course, always using the same 63programming interface also means that when high-performance hardware 64facilities like PCI bus mastering DMA appear, it's hard to take advantage of 65them. Let's not go into that. 66 67One thing that makes ARCnet cards difficult to program for, however, is the 68limit on their packet sizes; standard ARCnet can only send packets that are 69up to 508 bytes in length. This is smaller than the Internet "bare minimum" 70of 576 bytes, let alone the Ethernet MTU of 1500. To compensate, an extra 71level of encapsulation is defined by RFC1201, which I call "packet 72splitting," that allows "virtual packets" to grow as large as 64K each, 73although they are generally kept down to the Ethernet-style 1500 bytes. 74 75For more information on the advantages and disadvantages (mostly the 76advantages) of ARCnet networks, you might try the "ARCnet Trade Association" 77WWW page: 78 79 http://www.arcnet.com 80 81 82Cabling ARCnet Networks 83======================= 84 85This section was rewritten by 86 87 Vojtech Pavlik <vojtech@suse.cz> 88 89using information from several people, including: 90 91 - Avery Pennraun <apenwarr@worldvisions.ca> 92 - Stephen A. Wood <saw@hallc1.cebaf.gov> 93 - John Paul Morrison <jmorriso@bogomips.ee.ubc.ca> 94 - Joachim Koenig <jojo@repas.de> 95 96and Avery touched it up a bit, at Vojtech's request. 97 98ARCnet (the classic 2.5 Mbps version) can be connected by two different 99types of cabling: coax and twisted pair. The other ARCnet-type networks 100(100 Mbps TCNS and 320 kbps - 32 Mbps ARCnet Plus) use different types of 101cabling (Type1, Fiber, C1, C4, C5). 102 103For a coax network, you "should" use 93 Ohm RG-62 cable. But other cables 104also work fine, because ARCnet is a very stable network. I personally use 75 105Ohm TV antenna cable. 106 107Cards for coax cabling are shipped in two different variants: for BUS and 108STAR network topologies. They are mostly the same. The only difference 109lies in the hybrid chip installed. BUS cards use high impedance output, 110while STAR use low impedance. Low impedance card (STAR) is electrically 111equal to a high impedance one with a terminator installed. 112 113Usually, the ARCnet networks are built up from STAR cards and hubs. There 114are two types of hubs - active and passive. Passive hubs are small boxes 115with four BNC connectors containing four 47 Ohm resistors:: 116 117 | | wires 118 R + junction 119 -R-+-R- R 47 Ohm resistors 120 R 121 | 122 123The shielding is connected together. Active hubs are much more complicated; 124they are powered and contain electronics to amplify the signal and send it 125to other segments of the net. They usually have eight connectors. Active 126hubs come in two variants - dumb and smart. The dumb variant just 127amplifies, but the smart one decodes to digital and encodes back all packets 128coming through. This is much better if you have several hubs in the net, 129since many dumb active hubs may worsen the signal quality. 130 131And now to the cabling. What you can connect together: 132 1331. A card to a card. This is the simplest way of creating a 2-computer 134 network. 135 1362. A card to a passive hub. Remember that all unused connectors on the hub 137 must be properly terminated with 93 Ohm (or something else if you don't 138 have the right ones) terminators. 139 140 (Avery's note: oops, I didn't know that. Mine (TV cable) works 141 anyway, though.) 142 1433. A card to an active hub. Here is no need to terminate the unused 144 connectors except some kind of aesthetic feeling. But, there may not be 145 more than eleven active hubs between any two computers. That of course 146 doesn't limit the number of active hubs on the network. 147 1484. An active hub to another. 149 1505. An active hub to passive hub. 151 152Remember that you cannot connect two passive hubs together. The power loss 153implied by such a connection is too high for the net to operate reliably. 154 155An example of a typical ARCnet network:: 156 157 R S - STAR type card 158 S------H--------A-------S R - Terminator 159 | | H - Hub 160 | | A - Active hub 161 | S----H----S 162 S | 163 | 164 S 165 166The BUS topology is very similar to the one used by Ethernet. The only 167difference is in cable and terminators: they should be 93 Ohm. Ethernet 168uses 50 Ohm impedance. You use T connectors to put the computers on a single 169line of cable, the bus. You have to put terminators at both ends of the 170cable. A typical BUS ARCnet network looks like:: 171 172 RT----T------T------T------T------TR 173 B B B B B B 174 175 B - BUS type card 176 R - Terminator 177 T - T connector 178 179But that is not all! The two types can be connected together. According to 180the official documentation the only way of connecting them is using an active 181hub:: 182 183 A------T------T------TR 184 | B B B 185 S---H---S 186 | 187 S 188 189The official docs also state that you can use STAR cards at the ends of 190BUS network in place of a BUS card and a terminator:: 191 192 S------T------T------S 193 B B 194 195But, according to my own experiments, you can simply hang a BUS type card 196anywhere in middle of a cable in a STAR topology network. And more - you 197can use the bus card in place of any star card if you use a terminator. Then 198you can build very complicated networks fulfilling all your needs! An 199example:: 200 201 S 202 | 203 RT------T-------T------H------S 204 B B B | 205 | R 206 S------A------T-------T-------A-------H------TR 207 | B B | | B 208 | S BT | 209 | | | S----A-----S 210 S------H---A----S | | 211 | | S------T----H---S | 212 S S B R S 213 214A basically different cabling scheme is used with Twisted Pair cabling. Each 215of the TP cards has two RJ (phone-cord style) connectors. The cards are 216then daisy-chained together using a cable connecting every two neighboring 217cards. The ends are terminated with RJ 93 Ohm terminators which plug into 218the empty connectors of cards on the ends of the chain. An example:: 219 220 ___________ ___________ 221 _R_|_ _|_|_ _|_R_ 222 | | | | | | 223 |Card | |Card | |Card | 224 |_____| |_____| |_____| 225 226 227There are also hubs for the TP topology. There is nothing difficult 228involved in using them; you just connect a TP chain to a hub on any end or 229even at both. This way you can create almost any network configuration. 230The maximum of 11 hubs between any two computers on the net applies here as 231well. An example:: 232 233 RP-------P--------P--------H-----P------P-----PR 234 | 235 RP-----H--------P--------H-----P------PR 236 | | 237 PR PR 238 239 R - RJ Terminator 240 P - TP Card 241 H - TP Hub 242 243Like any network, ARCnet has a limited cable length. These are the maximum 244cable lengths between two active ends (an active end being an active hub or 245a STAR card). 246 247 ========== ======= =========== 248 RG-62 93 Ohm up to 650 m 249 RG-59/U 75 Ohm up to 457 m 250 RG-11/U 75 Ohm up to 533 m 251 IBM Type 1 150 Ohm up to 200 m 252 IBM Type 3 100 Ohm up to 100 m 253 ========== ======= =========== 254 255The maximum length of all cables connected to a passive hub is limited to 65 256meters for RG-62 cabling; less for others. You can see that using passive 257hubs in a large network is a bad idea. The maximum length of a single "BUS 258Trunk" is about 300 meters for RG-62. The maximum distance between the two 259most distant points of the net is limited to 3000 meters. The maximum length 260of a TP cable between two cards/hubs is 650 meters. 261 262 263Setting the Jumpers 264=================== 265 266All ARCnet cards should have a total of four or five different settings: 267 268 - the I/O address: this is the "port" your ARCnet card is on. Probed 269 values in the Linux ARCnet driver are only from 0x200 through 0x3F0. (If 270 your card has additional ones, which is possible, please tell me.) This 271 should not be the same as any other device on your system. According to 272 a doc I got from Novell, MS Windows prefers values of 0x300 or more, 273 eating net connections on my system (at least) otherwise. My guess is 274 this may be because, if your card is at 0x2E0, probing for a serial port 275 at 0x2E8 will reset the card and probably mess things up royally. 276 277 - Avery's favourite: 0x300. 278 279 - the IRQ: on 8-bit cards, it might be 2 (9), 3, 4, 5, or 7. 280 on 16-bit cards, it might be 2 (9), 3, 4, 5, 7, or 10-15. 281 282 Make sure this is different from any other card on your system. Note 283 that IRQ2 is the same as IRQ9, as far as Linux is concerned. You can 284 "cat /proc/interrupts" for a somewhat complete list of which ones are in 285 use at any given time. Here is a list of common usages from Vojtech 286 Pavlik <vojtech@suse.cz>: 287 288 ("Not on bus" means there is no way for a card to generate this 289 interrupt) 290 291 ====== ========================================================= 292 IRQ 0 Timer 0 (Not on bus) 293 IRQ 1 Keyboard (Not on bus) 294 IRQ 2 IRQ Controller 2 (Not on bus, nor does interrupt the CPU) 295 IRQ 3 COM2 296 IRQ 4 COM1 297 IRQ 5 FREE (LPT2 if you have it; sometimes COM3; maybe PLIP) 298 IRQ 6 Floppy disk controller 299 IRQ 7 FREE (LPT1 if you don't use the polling driver; PLIP) 300 IRQ 8 Realtime Clock Interrupt (Not on bus) 301 IRQ 9 FREE (VGA vertical sync interrupt if enabled) 302 IRQ 10 FREE 303 IRQ 11 FREE 304 IRQ 12 FREE 305 IRQ 13 Numeric Coprocessor (Not on bus) 306 IRQ 14 Fixed Disk Controller 307 IRQ 15 FREE (Fixed Disk Controller 2 if you have it) 308 ====== ========================================================= 309 310 311 .. note:: 312 313 IRQ 9 is used on some video cards for the "vertical retrace" 314 interrupt. This interrupt would have been handy for things like 315 video games, as it occurs exactly once per screen refresh, but 316 unfortunately IBM cancelled this feature starting with the original 317 VGA and thus many VGA/SVGA cards do not support it. For this 318 reason, no modern software uses this interrupt and it can almost 319 always be safely disabled, if your video card supports it at all. 320 321 If your card for some reason CANNOT disable this IRQ (usually there 322 is a jumper), one solution would be to clip the printed circuit 323 contact on the board: it's the fourth contact from the left on the 324 back side. I take no responsibility if you try this. 325 326 - Avery's favourite: IRQ2 (actually IRQ9). Watch that VGA, though. 327 328 - the memory address: Unlike most cards, ARCnets use "shared memory" for 329 copying buffers around. Make SURE it doesn't conflict with any other 330 used memory in your system! 331 332 :: 333 334 A0000 - VGA graphics memory (ok if you don't have VGA) 335 B0000 - Monochrome text mode 336 C0000 \ One of these is your VGA BIOS - usually C0000. 337 E0000 / 338 F0000 - System BIOS 339 340 Anything less than 0xA0000 is, well, a BAD idea since it isn't above 341 640k. 342 343 - Avery's favourite: 0xD0000 344 345 - the station address: Every ARCnet card has its own "unique" network 346 address from 0 to 255. Unlike Ethernet, you can set this address 347 yourself with a jumper or switch (or on some cards, with special 348 software). Since it's only 8 bits, you can only have 254 ARCnet cards 349 on a network. DON'T use 0 or 255, since these are reserved (although 350 neat stuff will probably happen if you DO use them). By the way, if you 351 haven't already guessed, don't set this the same as any other ARCnet on 352 your network! 353 354 - Avery's favourite: 3 and 4. Not that it matters. 355 356 - There may be ETS1 and ETS2 settings. These may or may not make a 357 difference on your card (many manuals call them "reserved"), but are 358 used to change the delays used when powering up a computer on the 359 network. This is only necessary when wiring VERY long range ARCnet 360 networks, on the order of 4km or so; in any case, the only real 361 requirement here is that all cards on the network with ETS1 and ETS2 362 jumpers have them in the same position. Chris Hindy <chrish@io.org> 363 sent in a chart with actual values for this: 364 365 ======= ======= =============== ==================== 366 ET1 ET2 Response Time Reconfiguration Time 367 ======= ======= =============== ==================== 368 open open 74.7us 840us 369 open closed 283.4us 1680us 370 closed open 561.8us 1680us 371 closed closed 1118.6us 1680us 372 ======= ======= =============== ==================== 373 374 Make sure you set ETS1 and ETS2 to the SAME VALUE for all cards on your 375 network. 376 377Also, on many cards (not mine, though) there are red and green LED's. 378Vojtech Pavlik <vojtech@suse.cz> tells me this is what they mean: 379 380 =============== =============== ===================================== 381 GREEN RED Status 382 =============== =============== ===================================== 383 OFF OFF Power off 384 OFF Short flashes Cabling problems (broken cable or not 385 terminated) 386 OFF (short) ON Card init 387 ON ON Normal state - everything OK, nothing 388 happens 389 ON Long flashes Data transfer 390 ON OFF Never happens (maybe when wrong ID) 391 =============== =============== ===================================== 392 393 394The following is all the specific information people have sent me about 395their own particular ARCnet cards. It is officially a mess, and contains 396huge amounts of duplicated information. I have no time to fix it. If you 397want to, PLEASE DO! Just send me a 'diff -u' of all your changes. 398 399The model # is listed right above specifics for that card, so you should be 400able to use your text viewer's "search" function to find the entry you want. 401If you don't KNOW what kind of card you have, try looking through the 402various diagrams to see if you can tell. 403 404If your model isn't listed and/or has different settings, PLEASE PLEASE 405tell me. I had to figure mine out without the manual, and it WASN'T FUN! 406 407Even if your ARCnet model isn't listed, but has the same jumpers as another 408model that is, please e-mail me to say so. 409 410Cards Listed in this file (in this order, mostly): 411 412 =============== ======================= ==== 413 Manufacturer Model # Bits 414 =============== ======================= ==== 415 SMC PC100 8 416 SMC PC110 8 417 SMC PC120 8 418 SMC PC130 8 419 SMC PC270E 8 420 SMC PC500 16 421 SMC PC500Longboard 16 422 SMC PC550Longboard 16 423 SMC PC600 16 424 SMC PC710 8 425 SMC? LCS-8830(-T) 8/16 426 Puredata PDI507 8 427 CNet Tech CN120-Series 8 428 CNet Tech CN160-Series 16 429 Lantech? UM9065L chipset 8 430 Acer 5210-003 8 431 Datapoint? LAN-ARC-8 8 432 Topware TA-ARC/10 8 433 Thomas-Conrad 500-6242-0097 REV A 8 434 Waterloo? (C)1985 Waterloo Micro. 8 435 No Name -- 8/16 436 No Name Taiwan R.O.C? 8 437 No Name Model 9058 8 438 Tiara Tiara Lancard? 8 439 =============== ======================= ==== 440 441 442* SMC = Standard Microsystems Corp. 443* CNet Tech = CNet Technology, Inc. 444 445Unclassified Stuff 446================== 447 448 - Please send any other information you can find. 449 450 - And some other stuff (more info is welcome!):: 451 452 From: root@ultraworld.xs4all.nl (Timo Hilbrink) 453 To: apenwarr@foxnet.net (Avery Pennarun) 454 Date: Wed, 26 Oct 1994 02:10:32 +0000 (GMT) 455 Reply-To: timoh@xs4all.nl 456 457 [...parts deleted...] 458 459 About the jumpers: On my PC130 there is one more jumper, located near the 460 cable-connector and it's for changing to star or bus topology; 461 closed: star - open: bus 462 On the PC500 are some more jumper-pins, one block labeled with RX,PDN,TXI 463 and another with ALE,LA17,LA18,LA19 these are undocumented.. 464 465 [...more parts deleted...] 466 467 --- CUT --- 468 469Standard Microsystems Corp (SMC) 470================================ 471 472PC100, PC110, PC120, PC130 (8-bit cards) and PC500, PC600 (16-bit cards) 473------------------------------------------------------------------------ 474 475 - mainly from Avery Pennarun <apenwarr@worldvisions.ca>. Values depicted 476 are from Avery's setup. 477 - special thanks to Timo Hilbrink <timoh@xs4all.nl> for noting that PC120, 478 130, 500, and 600 all have the same switches as Avery's PC100. 479 PC500/600 have several extra, undocumented pins though. (?) 480 - PC110 settings were verified by Stephen A. Wood <saw@cebaf.gov> 481 - Also, the JP- and S-numbers probably don't match your card exactly. Try 482 to find jumpers/switches with the same number of settings - it's 483 probably more reliable. 484 485:: 486 487 JP5 [|] : : : : 488 (IRQ Setting) IRQ2 IRQ3 IRQ4 IRQ5 IRQ7 489 Put exactly one jumper on exactly one set of pins. 490 491 492 1 2 3 4 5 6 7 8 9 10 493 S1 /----------------------------------\ 494 (I/O and Memory | 1 1 * 0 0 0 0 * 1 1 0 1 | 495 addresses) \----------------------------------/ 496 |--| |--------| |--------| 497 (a) (b) (m) 498 499 WARNING. It's very important when setting these which way 500 you're holding the card, and which way you think is '1'! 501 502 If you suspect that your settings are not being made 503 correctly, try reversing the direction or inverting the 504 switch positions. 505 506 a: The first digit of the I/O address. 507 Setting Value 508 ------- ----- 509 00 0 510 01 1 511 10 2 512 11 3 513 514 b: The second digit of the I/O address. 515 Setting Value 516 ------- ----- 517 0000 0 518 0001 1 519 0010 2 520 ... ... 521 1110 E 522 1111 F 523 524 The I/O address is in the form ab0. For example, if 525 a is 0x2 and b is 0xE, the address will be 0x2E0. 526 527 DO NOT SET THIS LESS THAN 0x200!!!!! 528 529 530 m: The first digit of the memory address. 531 Setting Value 532 ------- ----- 533 0000 0 534 0001 1 535 0010 2 536 ... ... 537 1110 E 538 1111 F 539 540 The memory address is in the form m0000. For example, if 541 m is D, the address will be 0xD0000. 542 543 DO NOT SET THIS TO C0000, F0000, OR LESS THAN A0000! 544 545 1 2 3 4 5 6 7 8 546 S2 /--------------------------\ 547 (Station Address) | 1 1 0 0 0 0 0 0 | 548 \--------------------------/ 549 550 Setting Value 551 ------- ----- 552 00000000 00 553 10000000 01 554 01000000 02 555 ... 556 01111111 FE 557 11111111 FF 558 559 Note that this is binary with the digits reversed! 560 561 DO NOT SET THIS TO 0 OR 255 (0xFF)! 562 563 564PC130E/PC270E (8-bit cards) 565--------------------------- 566 567 - from Juergen Seifert <seifert@htwm.de> 568 569This description has been written by Juergen Seifert <seifert@htwm.de> 570using information from the following Original SMC Manual 571 572 "Configuration Guide for ARCNET(R)-PC130E/PC270 Network 573 Controller Boards Pub. # 900.044A June, 1989" 574 575ARCNET is a registered trademark of the Datapoint Corporation 576SMC is a registered trademark of the Standard Microsystems Corporation 577 578The PC130E is an enhanced version of the PC130 board, is equipped with a 579standard BNC female connector for connection to RG-62/U coax cable. 580Since this board is designed both for point-to-point connection in star 581networks and for connection to bus networks, it is downwardly compatible 582with all the other standard boards designed for coax networks (that is, 583the PC120, PC110 and PC100 star topology boards and the PC220, PC210 and 584PC200 bus topology boards). 585 586The PC270E is an enhanced version of the PC260 board, is equipped with two 587modular RJ11-type jacks for connection to twisted pair wiring. 588It can be used in a star or a daisy-chained network. 589 590:: 591 592 8 7 6 5 4 3 2 1 593 ________________________________________________________________ 594 | | S1 | | 595 | |_________________| | 596 | Offs|Base |I/O Addr | 597 | RAM Addr | ___| 598 | ___ ___ CR3 |___| 599 | | \/ | CR4 |___| 600 | | PROM | ___| 601 | | | N | | 8 602 | | SOCKET | o | | 7 603 | |________| d | | 6 604 | ___________________ e | | 5 605 | | | A | S | 4 606 | |oo| EXT2 | | d | 2 | 3 607 | |oo| EXT1 | SMC | d | | 2 608 | |oo| ROM | 90C63 | r |___| 1 609 | |oo| IRQ7 | | |o| _____| 610 | |oo| IRQ5 | | |o| | J1 | 611 | |oo| IRQ4 | | STAR |_____| 612 | |oo| IRQ3 | | | J2 | 613 | |oo| IRQ2 |___________________| |_____| 614 |___ ______________| 615 | | 616 |_____________________________________________| 617 618Legend:: 619 620 SMC 90C63 ARCNET Controller / Transceiver /Logic 621 S1 1-3: I/O Base Address Select 622 4-6: Memory Base Address Select 623 7-8: RAM Offset Select 624 S2 1-8: Node ID Select 625 EXT Extended Timeout Select 626 ROM ROM Enable Select 627 STAR Selected - Star Topology (PC130E only) 628 Deselected - Bus Topology (PC130E only) 629 CR3/CR4 Diagnostic LEDs 630 J1 BNC RG62/U Connector (PC130E only) 631 J1 6-position Telephone Jack (PC270E only) 632 J2 6-position Telephone Jack (PC270E only) 633 634Setting one of the switches to Off/Open means "1", On/Closed means "0". 635 636 637Setting the Node ID 638^^^^^^^^^^^^^^^^^^^ 639 640The eight switches in group S2 are used to set the node ID. 641These switches work in a way similar to the PC100-series cards; see that 642entry for more information. 643 644 645Setting the I/O Base Address 646^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 647 648The first three switches in switch group S1 are used to select one 649of eight possible I/O Base addresses using the following table:: 650 651 652 Switch | Hex I/O 653 1 2 3 | Address 654 -------|-------- 655 0 0 0 | 260 656 0 0 1 | 290 657 0 1 0 | 2E0 (Manufacturer's default) 658 0 1 1 | 2F0 659 1 0 0 | 300 660 1 0 1 | 350 661 1 1 0 | 380 662 1 1 1 | 3E0 663 664 665Setting the Base Memory (RAM) buffer Address 666^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 667 668The memory buffer requires 2K of a 16K block of RAM. The base of this 66916K block can be located in any of eight positions. 670Switches 4-6 of switch group S1 select the Base of the 16K block. 671Within that 16K address space, the buffer may be assigned any one of four 672positions, determined by the offset, switches 7 and 8 of group S1. 673 674:: 675 676 Switch | Hex RAM | Hex ROM 677 4 5 6 7 8 | Address | Address *) 678 -----------|---------|----------- 679 0 0 0 0 0 | C0000 | C2000 680 0 0 0 0 1 | C0800 | C2000 681 0 0 0 1 0 | C1000 | C2000 682 0 0 0 1 1 | C1800 | C2000 683 | | 684 0 0 1 0 0 | C4000 | C6000 685 0 0 1 0 1 | C4800 | C6000 686 0 0 1 1 0 | C5000 | C6000 687 0 0 1 1 1 | C5800 | C6000 688 | | 689 0 1 0 0 0 | CC000 | CE000 690 0 1 0 0 1 | CC800 | CE000 691 0 1 0 1 0 | CD000 | CE000 692 0 1 0 1 1 | CD800 | CE000 693 | | 694 0 1 1 0 0 | D0000 | D2000 (Manufacturer's default) 695 0 1 1 0 1 | D0800 | D2000 696 0 1 1 1 0 | D1000 | D2000 697 0 1 1 1 1 | D1800 | D2000 698 | | 699 1 0 0 0 0 | D4000 | D6000 700 1 0 0 0 1 | D4800 | D6000 701 1 0 0 1 0 | D5000 | D6000 702 1 0 0 1 1 | D5800 | D6000 703 | | 704 1 0 1 0 0 | D8000 | DA000 705 1 0 1 0 1 | D8800 | DA000 706 1 0 1 1 0 | D9000 | DA000 707 1 0 1 1 1 | D9800 | DA000 708 | | 709 1 1 0 0 0 | DC000 | DE000 710 1 1 0 0 1 | DC800 | DE000 711 1 1 0 1 0 | DD000 | DE000 712 1 1 0 1 1 | DD800 | DE000 713 | | 714 1 1 1 0 0 | E0000 | E2000 715 1 1 1 0 1 | E0800 | E2000 716 1 1 1 1 0 | E1000 | E2000 717 1 1 1 1 1 | E1800 | E2000 718 719 *) To enable the 8K Boot PROM install the jumper ROM. 720 The default is jumper ROM not installed. 721 722 723Setting the Timeouts and Interrupt 724^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 725 726The jumpers labeled EXT1 and EXT2 are used to determine the timeout 727parameters. These two jumpers are normally left open. 728 729To select a hardware interrupt level set one (only one!) of the jumpers 730IRQ2, IRQ3, IRQ4, IRQ5, IRQ7. The Manufacturer's default is IRQ2. 731 732 733Configuring the PC130E for Star or Bus Topology 734^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 735 736The single jumper labeled STAR is used to configure the PC130E board for 737star or bus topology. 738When the jumper is installed, the board may be used in a star network, when 739it is removed, the board can be used in a bus topology. 740 741 742Diagnostic LEDs 743^^^^^^^^^^^^^^^ 744 745Two diagnostic LEDs are visible on the rear bracket of the board. 746The green LED monitors the network activity: the red one shows the 747board activity:: 748 749 Green | Status Red | Status 750 -------|------------------- ---------|------------------- 751 on | normal activity flash/on | data transfer 752 blink | reconfiguration off | no data transfer; 753 off | defective board or | incorrect memory or 754 | node ID is zero | I/O address 755 756 757PC500/PC550 Longboard (16-bit cards) 758------------------------------------ 759 760 - from Juergen Seifert <seifert@htwm.de> 761 762 763 .. note:: 764 765 There is another Version of the PC500 called Short Version, which 766 is different in hard- and software! The most important differences 767 are: 768 769 - The long board has no Shared memory. 770 - On the long board the selection of the interrupt is done by binary 771 coded switch, on the short board directly by jumper. 772 773[Avery's note: pay special attention to that: the long board HAS NO SHARED 774MEMORY. This means the current Linux-ARCnet driver can't use these cards. 775I have obtained a PC500Longboard and will be doing some experiments on it in 776the future, but don't hold your breath. Thanks again to Juergen Seifert for 777his advice about this!] 778 779This description has been written by Juergen Seifert <seifert@htwm.de> 780using information from the following Original SMC Manual 781 782 "Configuration Guide for SMC ARCNET-PC500/PC550 783 Series Network Controller Boards Pub. # 900.033 Rev. A 784 November, 1989" 785 786ARCNET is a registered trademark of the Datapoint Corporation 787SMC is a registered trademark of the Standard Microsystems Corporation 788 789The PC500 is equipped with a standard BNC female connector for connection 790to RG-62/U coax cable. 791The board is designed both for point-to-point connection in star networks 792and for connection to bus networks. 793 794The PC550 is equipped with two modular RJ11-type jacks for connection 795to twisted pair wiring. 796It can be used in a star or a daisy-chained (BUS) network. 797 798:: 799 800 1 801 0 9 8 7 6 5 4 3 2 1 6 5 4 3 2 1 802 ____________________________________________________________________ 803 < | SW1 | | SW2 | | 804 > |_____________________| |_____________| | 805 < IRQ |I/O Addr | 806 > ___| 807 < CR4 |___| 808 > CR3 |___| 809 < ___| 810 > N | | 8 811 < o | | 7 812 > d | S | 6 813 < e | W | 5 814 > A | 3 | 4 815 < d | | 3 816 > d | | 2 817 < r |___| 1 818 > |o| _____| 819 < |o| | J1 | 820 > 3 1 JP6 |_____| 821 < |o|o| JP2 | J2 | 822 > |o|o| |_____| 823 < 4 2__ ______________| 824 > | | | 825 <____| |_____________________________________________| 826 827Legend:: 828 829 SW1 1-6: I/O Base Address Select 830 7-10: Interrupt Select 831 SW2 1-6: Reserved for Future Use 832 SW3 1-8: Node ID Select 833 JP2 1-4: Extended Timeout Select 834 JP6 Selected - Star Topology (PC500 only) 835 Deselected - Bus Topology (PC500 only) 836 CR3 Green Monitors Network Activity 837 CR4 Red Monitors Board Activity 838 J1 BNC RG62/U Connector (PC500 only) 839 J1 6-position Telephone Jack (PC550 only) 840 J2 6-position Telephone Jack (PC550 only) 841 842Setting one of the switches to Off/Open means "1", On/Closed means "0". 843 844 845Setting the Node ID 846^^^^^^^^^^^^^^^^^^^ 847 848The eight switches in group SW3 are used to set the node ID. Each node 849attached to the network must have an unique node ID which must be 850different from 0. 851Switch 1 serves as the least significant bit (LSB). 852 853The node ID is the sum of the values of all switches set to "1" 854These values are:: 855 856 Switch | Value 857 -------|------- 858 1 | 1 859 2 | 2 860 3 | 4 861 4 | 8 862 5 | 16 863 6 | 32 864 7 | 64 865 8 | 128 866 867Some Examples:: 868 869 Switch | Hex | Decimal 870 8 7 6 5 4 3 2 1 | Node ID | Node ID 871 ----------------|---------|--------- 872 0 0 0 0 0 0 0 0 | not allowed 873 0 0 0 0 0 0 0 1 | 1 | 1 874 0 0 0 0 0 0 1 0 | 2 | 2 875 0 0 0 0 0 0 1 1 | 3 | 3 876 . . . | | 877 0 1 0 1 0 1 0 1 | 55 | 85 878 . . . | | 879 1 0 1 0 1 0 1 0 | AA | 170 880 . . . | | 881 1 1 1 1 1 1 0 1 | FD | 253 882 1 1 1 1 1 1 1 0 | FE | 254 883 1 1 1 1 1 1 1 1 | FF | 255 884 885 886Setting the I/O Base Address 887^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 888 889The first six switches in switch group SW1 are used to select one 890of 32 possible I/O Base addresses using the following table:: 891 892 Switch | Hex I/O 893 6 5 4 3 2 1 | Address 894 -------------|-------- 895 0 1 0 0 0 0 | 200 896 0 1 0 0 0 1 | 210 897 0 1 0 0 1 0 | 220 898 0 1 0 0 1 1 | 230 899 0 1 0 1 0 0 | 240 900 0 1 0 1 0 1 | 250 901 0 1 0 1 1 0 | 260 902 0 1 0 1 1 1 | 270 903 0 1 1 0 0 0 | 280 904 0 1 1 0 0 1 | 290 905 0 1 1 0 1 0 | 2A0 906 0 1 1 0 1 1 | 2B0 907 0 1 1 1 0 0 | 2C0 908 0 1 1 1 0 1 | 2D0 909 0 1 1 1 1 0 | 2E0 (Manufacturer's default) 910 0 1 1 1 1 1 | 2F0 911 1 1 0 0 0 0 | 300 912 1 1 0 0 0 1 | 310 913 1 1 0 0 1 0 | 320 914 1 1 0 0 1 1 | 330 915 1 1 0 1 0 0 | 340 916 1 1 0 1 0 1 | 350 917 1 1 0 1 1 0 | 360 918 1 1 0 1 1 1 | 370 919 1 1 1 0 0 0 | 380 920 1 1 1 0 0 1 | 390 921 1 1 1 0 1 0 | 3A0 922 1 1 1 0 1 1 | 3B0 923 1 1 1 1 0 0 | 3C0 924 1 1 1 1 0 1 | 3D0 925 1 1 1 1 1 0 | 3E0 926 1 1 1 1 1 1 | 3F0 927 928 929Setting the Interrupt 930^^^^^^^^^^^^^^^^^^^^^ 931 932Switches seven through ten of switch group SW1 are used to select the 933interrupt level. The interrupt level is binary coded, so selections 934from 0 to 15 would be possible, but only the following eight values will 935be supported: 3, 4, 5, 7, 9, 10, 11, 12. 936 937:: 938 939 Switch | IRQ 940 10 9 8 7 | 941 ---------|-------- 942 0 0 1 1 | 3 943 0 1 0 0 | 4 944 0 1 0 1 | 5 945 0 1 1 1 | 7 946 1 0 0 1 | 9 (=2) (default) 947 1 0 1 0 | 10 948 1 0 1 1 | 11 949 1 1 0 0 | 12 950 951 952Setting the Timeouts 953^^^^^^^^^^^^^^^^^^^^ 954 955The two jumpers JP2 (1-4) are used to determine the timeout parameters. 956These two jumpers are normally left open. 957Refer to the COM9026 Data Sheet for alternate configurations. 958 959 960Configuring the PC500 for Star or Bus Topology 961^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 962 963The single jumper labeled JP6 is used to configure the PC500 board for 964star or bus topology. 965When the jumper is installed, the board may be used in a star network, when 966it is removed, the board can be used in a bus topology. 967 968 969Diagnostic LEDs 970^^^^^^^^^^^^^^^ 971 972Two diagnostic LEDs are visible on the rear bracket of the board. 973The green LED monitors the network activity: the red one shows the 974board activity:: 975 976 Green | Status Red | Status 977 -------|------------------- ---------|------------------- 978 on | normal activity flash/on | data transfer 979 blink | reconfiguration off | no data transfer; 980 off | defective board or | incorrect memory or 981 | node ID is zero | I/O address 982 983 984PC710 (8-bit card) 985------------------ 986 987 - from J.S. van Oosten <jvoosten@compiler.tdcnet.nl> 988 989Note: this data is gathered by experimenting and looking at info of other 990cards. However, I'm sure I got 99% of the settings right. 991 992The SMC710 card resembles the PC270 card, but is much more basic (i.e. no 993LEDs, RJ11 jacks, etc.) and 8 bit. Here's a little drawing:: 994 995 _______________________________________ 996 | +---------+ +---------+ |____ 997 | | S2 | | S1 | | 998 | +---------+ +---------+ | 999 | | 1000 | +===+ __ | 1001 | | R | | | X-tal ###___ 1002 | | O | |__| ####__'| 1003 | | M | || ### 1004 | +===+ | 1005 | | 1006 | .. JP1 +----------+ | 1007 | .. | big chip | | 1008 | .. | 90C63 | | 1009 | .. | | | 1010 | .. +----------+ | 1011 ------- ----------- 1012 ||||||||||||||||||||| 1013 1014The row of jumpers at JP1 actually consists of 8 jumpers, (sometimes 1015labelled) the same as on the PC270, from top to bottom: EXT2, EXT1, ROM, 1016IRQ7, IRQ5, IRQ4, IRQ3, IRQ2 (gee, wonder what they would do? :-) ) 1017 1018S1 and S2 perform the same function as on the PC270, only their numbers 1019are swapped (S1 is the nodeaddress, S2 sets IO- and RAM-address). 1020 1021I know it works when connected to a PC110 type ARCnet board. 1022 1023 1024***************************************************************************** 1025 1026Possibly SMC 1027============ 1028 1029LCS-8830(-T) (8 and 16-bit cards) 1030--------------------------------- 1031 1032 - from Mathias Katzer <mkatzer@HRZ.Uni-Bielefeld.DE> 1033 - Marek Michalkiewicz <marekm@i17linuxb.ists.pwr.wroc.pl> says the 1034 LCS-8830 is slightly different from LCS-8830-T. These are 8 bit, BUS 1035 only (the JP0 jumper is hardwired), and BNC only. 1036 1037This is a LCS-8830-T made by SMC, I think ('SMC' only appears on one PLCC, 1038nowhere else, not even on the few Xeroxed sheets from the manual). 1039 1040SMC ARCnet Board Type LCS-8830-T:: 1041 1042 ------------------------------------ 1043 | | 1044 | JP3 88 8 JP2 | 1045 | ##### | \ | 1046 | ##### ET1 ET2 ###| 1047 | 8 ###| 1048 | U3 SW 1 JP0 ###| Phone Jacks 1049 | -- ###| 1050 | | | | 1051 | | | SW2 | 1052 | | | | 1053 | | | ##### | 1054 | -- ##### #### BNC Connector 1055 | #### 1056 | 888888 JP1 | 1057 | 234567 | 1058 -- ------- 1059 ||||||||||||||||||||||||||| 1060 -------------------------- 1061 1062 1063 SW1: DIP-Switches for Station Address 1064 SW2: DIP-Switches for Memory Base and I/O Base addresses 1065 1066 JP0: If closed, internal termination on (default open) 1067 JP1: IRQ Jumpers 1068 JP2: Boot-ROM enabled if closed 1069 JP3: Jumpers for response timeout 1070 1071 U3: Boot-ROM Socket 1072 1073 1074 ET1 ET2 Response Time Idle Time Reconfiguration Time 1075 1076 78 86 840 1077 X 285 316 1680 1078 X 563 624 1680 1079 X X 1130 1237 1680 1080 1081 (X means closed jumper) 1082 1083 (DIP-Switch downwards means "0") 1084 1085The station address is binary-coded with SW1. 1086 1087The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2: 1088 1089======== ======== 1090Switches Base 1091678 Address 1092======== ======== 1093000 260-26f 1094100 290-29f 1095010 2e0-2ef 1096110 2f0-2ff 1097001 300-30f 1098101 350-35f 1099011 380-38f 1100111 3e0-3ef 1101======== ======== 1102 1103 1104DIP Switches 1-5 of SW2 encode the RAM and ROM Address Range: 1105 1106======== ============= ================ 1107Switches RAM ROM 110812345 Address Range Address Range 1109======== ============= ================ 111000000 C:0000-C:07ff C:2000-C:3fff 111110000 C:0800-C:0fff 111201000 C:1000-C:17ff 111311000 C:1800-C:1fff 111400100 C:4000-C:47ff C:6000-C:7fff 111510100 C:4800-C:4fff 111601100 C:5000-C:57ff 111711100 C:5800-C:5fff 111800010 C:C000-C:C7ff C:E000-C:ffff 111910010 C:C800-C:Cfff 112001010 C:D000-C:D7ff 112111010 C:D800-C:Dfff 112200110 D:0000-D:07ff D:2000-D:3fff 112310110 D:0800-D:0fff 112401110 D:1000-D:17ff 112511110 D:1800-D:1fff 112600001 D:4000-D:47ff D:6000-D:7fff 112710001 D:4800-D:4fff 112801001 D:5000-D:57ff 112911001 D:5800-D:5fff 113000101 D:8000-D:87ff D:A000-D:bfff 113110101 D:8800-D:8fff 113201101 D:9000-D:97ff 113311101 D:9800-D:9fff 113400011 D:C000-D:c7ff D:E000-D:ffff 113510011 D:C800-D:cfff 113601011 D:D000-D:d7ff 113711011 D:D800-D:dfff 113800111 E:0000-E:07ff E:2000-E:3fff 113910111 E:0800-E:0fff 114001111 E:1000-E:17ff 114111111 E:1800-E:1fff 1142======== ============= ================ 1143 1144 1145PureData Corp 1146============= 1147 1148PDI507 (8-bit card) 1149-------------------- 1150 1151 - from Mark Rejhon <mdrejhon@magi.com> (slight modifications by Avery) 1152 - Avery's note: I think PDI508 cards (but definitely NOT PDI508Plus cards) 1153 are mostly the same as this. PDI508Plus cards appear to be mainly 1154 software-configured. 1155 1156Jumpers: 1157 1158 There is a jumper array at the bottom of the card, near the edge 1159 connector. This array is labelled J1. They control the IRQs and 1160 something else. Put only one jumper on the IRQ pins. 1161 1162 ETS1, ETS2 are for timing on very long distance networks. See the 1163 more general information near the top of this file. 1164 1165 There is a J2 jumper on two pins. A jumper should be put on them, 1166 since it was already there when I got the card. I don't know what 1167 this jumper is for though. 1168 1169 There is a two-jumper array for J3. I don't know what it is for, 1170 but there were already two jumpers on it when I got the card. It's 1171 a six pin grid in a two-by-three fashion. The jumpers were 1172 configured as follows:: 1173 1174 .-------. 1175 o | o o | 1176 :-------: ------> Accessible end of card with connectors 1177 o | o o | in this direction -------> 1178 `-------' 1179 1180Carl de Billy <CARL@carainfo.com> explains J3 and J4: 1181 1182 J3 Diagram:: 1183 1184 .-------. 1185 o | o o | 1186 :-------: TWIST Technology 1187 o | o o | 1188 `-------' 1189 .-------. 1190 | o o | o 1191 :-------: COAX Technology 1192 | o o | o 1193 `-------' 1194 1195 - If using coax cable in a bus topology the J4 jumper must be removed; 1196 place it on one pin. 1197 1198 - If using bus topology with twisted pair wiring move the J3 1199 jumpers so they connect the middle pin and the pins closest to the RJ11 1200 Connectors. Also the J4 jumper must be removed; place it on one pin of 1201 J4 jumper for storage. 1202 1203 - If using star topology with twisted pair wiring move the J3 1204 jumpers so they connect the middle pin and the pins closest to the RJ11 1205 connectors. 1206 1207 1208DIP Switches: 1209 1210 The DIP switches accessible on the accessible end of the card while 1211 it is installed, is used to set the ARCnet address. There are 8 1212 switches. Use an address from 1 to 254 1213 1214 ========== ========================= 1215 Switch No. ARCnet address 1216 12345678 1217 ========== ========================= 1218 00000000 FF (Don't use this!) 1219 00000001 FE 1220 00000010 FD 1221 ... 1222 11111101 2 1223 11111110 1 1224 11111111 0 (Don't use this!) 1225 ========== ========================= 1226 1227 There is another array of eight DIP switches at the top of the 1228 card. There are five labelled MS0-MS4 which seem to control the 1229 memory address, and another three labelled IO0-IO2 which seem to 1230 control the base I/O address of the card. 1231 1232 This was difficult to test by trial and error, and the I/O addresses 1233 are in a weird order. This was tested by setting the DIP switches, 1234 rebooting the computer, and attempting to load ARCETHER at various 1235 addresses (mostly between 0x200 and 0x400). The address that caused 1236 the red transmit LED to blink, is the one that I thought works. 1237 1238 Also, the address 0x3D0 seem to have a special meaning, since the 1239 ARCETHER packet driver loaded fine, but without the red LED 1240 blinking. I don't know what 0x3D0 is for though. I recommend using 1241 an address of 0x300 since Windows may not like addresses below 1242 0x300. 1243 1244 ============= =========== 1245 IO Switch No. I/O address 1246 210 1247 ============= =========== 1248 111 0x260 1249 110 0x290 1250 101 0x2E0 1251 100 0x2F0 1252 011 0x300 1253 010 0x350 1254 001 0x380 1255 000 0x3E0 1256 ============= =========== 1257 1258 The memory switches set a reserved address space of 0x1000 bytes 1259 (0x100 segment units, or 4k). For example if I set an address of 1260 0xD000, it will use up addresses 0xD000 to 0xD100. 1261 1262 The memory switches were tested by booting using QEMM386 stealth, 1263 and using LOADHI to see what address automatically became excluded 1264 from the upper memory regions, and then attempting to load ARCETHER 1265 using these addresses. 1266 1267 I recommend using an ARCnet memory address of 0xD000, and putting 1268 the EMS page frame at 0xC000 while using QEMM stealth mode. That 1269 way, you get contiguous high memory from 0xD100 almost all the way 1270 the end of the megabyte. 1271 1272 Memory Switch 0 (MS0) didn't seem to work properly when set to OFF 1273 on my card. It could be malfunctioning on my card. Experiment with 1274 it ON first, and if it doesn't work, set it to OFF. (It may be a 1275 modifier for the 0x200 bit?) 1276 1277 ============= ============================================ 1278 MS Switch No. 1279 43210 Memory address 1280 ============= ============================================ 1281 00001 0xE100 (guessed - was not detected by QEMM) 1282 00011 0xE000 (guessed - was not detected by QEMM) 1283 00101 0xDD00 1284 00111 0xDC00 1285 01001 0xD900 1286 01011 0xD800 1287 01101 0xD500 1288 01111 0xD400 1289 10001 0xD100 1290 10011 0xD000 1291 10101 0xCD00 1292 10111 0xCC00 1293 11001 0xC900 (guessed - crashes tested system) 1294 11011 0xC800 (guessed - crashes tested system) 1295 11101 0xC500 (guessed - crashes tested system) 1296 11111 0xC400 (guessed - crashes tested system) 1297 ============= ============================================ 1298 1299CNet Technology Inc. (8-bit cards) 1300================================== 1301 1302120 Series (8-bit cards) 1303------------------------ 1304 - from Juergen Seifert <seifert@htwm.de> 1305 1306This description has been written by Juergen Seifert <seifert@htwm.de> 1307using information from the following Original CNet Manual 1308 1309 "ARCNET USER'S MANUAL for 1310 CN120A 1311 CN120AB 1312 CN120TP 1313 CN120ST 1314 CN120SBT 1315 P/N:12-01-0007 1316 Revision 3.00" 1317 1318ARCNET is a registered trademark of the Datapoint Corporation 1319 1320- P/N 120A ARCNET 8 bit XT/AT Star 1321- P/N 120AB ARCNET 8 bit XT/AT Bus 1322- P/N 120TP ARCNET 8 bit XT/AT Twisted Pair 1323- P/N 120ST ARCNET 8 bit XT/AT Star, Twisted Pair 1324- P/N 120SBT ARCNET 8 bit XT/AT Star, Bus, Twisted Pair 1325 1326:: 1327 1328 __________________________________________________________________ 1329 | | 1330 | ___| 1331 | LED |___| 1332 | ___| 1333 | N | | ID7 1334 | o | | ID6 1335 | d | S | ID5 1336 | e | W | ID4 1337 | ___________________ A | 2 | ID3 1338 | | | d | | ID2 1339 | | | 1 2 3 4 5 6 7 8 d | | ID1 1340 | | | _________________ r |___| ID0 1341 | | 90C65 || SW1 | ____| 1342 | JP 8 7 | ||_________________| | | 1343 | |o|o| JP1 | | | J2 | 1344 | |o|o| |oo| | | JP 1 1 1 | | 1345 | ______________ | | 0 1 2 |____| 1346 | | PROM | |___________________| |o|o|o| _____| 1347 | > SOCKET | JP 6 5 4 3 2 |o|o|o| | J1 | 1348 | |______________| |o|o|o|o|o| |o|o|o| |_____| 1349 |_____ |o|o|o|o|o| ______________| 1350 | | 1351 |_____________________________________________| 1352 1353Legend:: 1354 1355 90C65 ARCNET Probe 1356 S1 1-5: Base Memory Address Select 1357 6-8: Base I/O Address Select 1358 S2 1-8: Node ID Select (ID0-ID7) 1359 JP1 ROM Enable Select 1360 JP2 IRQ2 1361 JP3 IRQ3 1362 JP4 IRQ4 1363 JP5 IRQ5 1364 JP6 IRQ7 1365 JP7/JP8 ET1, ET2 Timeout Parameters 1366 JP10/JP11 Coax / Twisted Pair Select (CN120ST/SBT only) 1367 JP12 Terminator Select (CN120AB/ST/SBT only) 1368 J1 BNC RG62/U Connector (all except CN120TP) 1369 J2 Two 6-position Telephone Jack (CN120TP/ST/SBT only) 1370 1371Setting one of the switches to Off means "1", On means "0". 1372 1373 1374Setting the Node ID 1375^^^^^^^^^^^^^^^^^^^ 1376 1377The eight switches in SW2 are used to set the node ID. Each node attached 1378to the network must have an unique node ID which must be different from 0. 1379Switch 1 (ID0) serves as the least significant bit (LSB). 1380 1381The node ID is the sum of the values of all switches set to "1" 1382These values are: 1383 1384 ======= ====== ===== 1385 Switch Label Value 1386 ======= ====== ===== 1387 1 ID0 1 1388 2 ID1 2 1389 3 ID2 4 1390 4 ID3 8 1391 5 ID4 16 1392 6 ID5 32 1393 7 ID6 64 1394 8 ID7 128 1395 ======= ====== ===== 1396 1397Some Examples:: 1398 1399 Switch | Hex | Decimal 1400 8 7 6 5 4 3 2 1 | Node ID | Node ID 1401 ----------------|---------|--------- 1402 0 0 0 0 0 0 0 0 | not allowed 1403 0 0 0 0 0 0 0 1 | 1 | 1 1404 0 0 0 0 0 0 1 0 | 2 | 2 1405 0 0 0 0 0 0 1 1 | 3 | 3 1406 . . . | | 1407 0 1 0 1 0 1 0 1 | 55 | 85 1408 . . . | | 1409 1 0 1 0 1 0 1 0 | AA | 170 1410 . . . | | 1411 1 1 1 1 1 1 0 1 | FD | 253 1412 1 1 1 1 1 1 1 0 | FE | 254 1413 1 1 1 1 1 1 1 1 | FF | 255 1414 1415 1416Setting the I/O Base Address 1417^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1418 1419The last three switches in switch block SW1 are used to select one 1420of eight possible I/O Base addresses using the following table:: 1421 1422 1423 Switch | Hex I/O 1424 6 7 8 | Address 1425 ------------|-------- 1426 ON ON ON | 260 1427 OFF ON ON | 290 1428 ON OFF ON | 2E0 (Manufacturer's default) 1429 OFF OFF ON | 2F0 1430 ON ON OFF | 300 1431 OFF ON OFF | 350 1432 ON OFF OFF | 380 1433 OFF OFF OFF | 3E0 1434 1435 1436Setting the Base Memory (RAM) buffer Address 1437^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1438 1439The memory buffer (RAM) requires 2K. The base of this buffer can be 1440located in any of eight positions. The address of the Boot Prom is 1441memory base + 8K or memory base + 0x2000. 1442Switches 1-5 of switch block SW1 select the Memory Base address. 1443 1444:: 1445 1446 Switch | Hex RAM | Hex ROM 1447 1 2 3 4 5 | Address | Address *) 1448 --------------------|---------|----------- 1449 ON ON ON ON ON | C0000 | C2000 1450 ON ON OFF ON ON | C4000 | C6000 1451 ON ON ON OFF ON | CC000 | CE000 1452 ON ON OFF OFF ON | D0000 | D2000 (Manufacturer's default) 1453 ON ON ON ON OFF | D4000 | D6000 1454 ON ON OFF ON OFF | D8000 | DA000 1455 ON ON ON OFF OFF | DC000 | DE000 1456 ON ON OFF OFF OFF | E0000 | E2000 1457 1458 *) To enable the Boot ROM install the jumper JP1 1459 1460.. note:: 1461 1462 Since the switches 1 and 2 are always set to ON it may be possible 1463 that they can be used to add an offset of 2K, 4K or 6K to the base 1464 address, but this feature is not documented in the manual and I 1465 haven't tested it yet. 1466 1467 1468Setting the Interrupt Line 1469^^^^^^^^^^^^^^^^^^^^^^^^^^ 1470 1471To select a hardware interrupt level install one (only one!) of the jumpers 1472JP2, JP3, JP4, JP5, JP6. JP2 is the default:: 1473 1474 Jumper | IRQ 1475 -------|----- 1476 2 | 2 1477 3 | 3 1478 4 | 4 1479 5 | 5 1480 6 | 7 1481 1482 1483Setting the Internal Terminator on CN120AB/TP/SBT 1484^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1485 1486The jumper JP12 is used to enable the internal terminator:: 1487 1488 ----- 1489 0 | 0 | 1490 ----- ON | | ON 1491 | 0 | | 0 | 1492 | | OFF ----- OFF 1493 | 0 | 0 1494 ----- 1495 Terminator Terminator 1496 disabled enabled 1497 1498 1499Selecting the Connector Type on CN120ST/SBT 1500^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1501 1502:: 1503 1504 JP10 JP11 JP10 JP11 1505 ----- ----- 1506 0 0 | 0 | | 0 | 1507 ----- ----- | | | | 1508 | 0 | | 0 | | 0 | | 0 | 1509 | | | | ----- ----- 1510 | 0 | | 0 | 0 0 1511 ----- ----- 1512 Coaxial Cable Twisted Pair Cable 1513 (Default) 1514 1515 1516Setting the Timeout Parameters 1517^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1518 1519The jumpers labeled EXT1 and EXT2 are used to determine the timeout 1520parameters. These two jumpers are normally left open. 1521 1522 1523CNet Technology Inc. (16-bit cards) 1524=================================== 1525 1526160 Series (16-bit cards) 1527------------------------- 1528 - from Juergen Seifert <seifert@htwm.de> 1529 1530This description has been written by Juergen Seifert <seifert@htwm.de> 1531using information from the following Original CNet Manual 1532 1533 "ARCNET USER'S MANUAL for 1534 CN160A CN160AB CN160TP 1535 P/N:12-01-0006 Revision 3.00" 1536 1537ARCNET is a registered trademark of the Datapoint Corporation 1538 1539- P/N 160A ARCNET 16 bit XT/AT Star 1540- P/N 160AB ARCNET 16 bit XT/AT Bus 1541- P/N 160TP ARCNET 16 bit XT/AT Twisted Pair 1542 1543:: 1544 1545 ___________________________________________________________________ 1546 < _________________________ ___| 1547 > |oo| JP2 | | LED |___| 1548 < |oo| JP1 | 9026 | LED |___| 1549 > |_________________________| ___| 1550 < N | | ID7 1551 > 1 o | | ID6 1552 < 1 2 3 4 5 6 7 8 9 0 d | S | ID5 1553 > _______________ _____________________ e | W | ID4 1554 < | PROM | | SW1 | A | 2 | ID3 1555 > > SOCKET | |_____________________| d | | ID2 1556 < |_______________| | IO-Base | MEM | d | | ID1 1557 > r |___| ID0 1558 < ____| 1559 > | | 1560 < | J1 | 1561 > | | 1562 < |____| 1563 > 1 1 1 1 | 1564 < 3 4 5 6 7 JP 8 9 0 1 2 3 | 1565 > |o|o|o|o|o| |o|o|o|o|o|o| | 1566 < |o|o|o|o|o| __ |o|o|o|o|o|o| ___________| 1567 > | | | 1568 <____________| |_______________________________________| 1569 1570Legend:: 1571 1572 9026 ARCNET Probe 1573 SW1 1-6: Base I/O Address Select 1574 7-10: Base Memory Address Select 1575 SW2 1-8: Node ID Select (ID0-ID7) 1576 JP1/JP2 ET1, ET2 Timeout Parameters 1577 JP3-JP13 Interrupt Select 1578 J1 BNC RG62/U Connector (CN160A/AB only) 1579 J1 Two 6-position Telephone Jack (CN160TP only) 1580 LED 1581 1582Setting one of the switches to Off means "1", On means "0". 1583 1584 1585Setting the Node ID 1586^^^^^^^^^^^^^^^^^^^ 1587 1588The eight switches in SW2 are used to set the node ID. Each node attached 1589to the network must have an unique node ID which must be different from 0. 1590Switch 1 (ID0) serves as the least significant bit (LSB). 1591 1592The node ID is the sum of the values of all switches set to "1" 1593These values are:: 1594 1595 Switch | Label | Value 1596 -------|-------|------- 1597 1 | ID0 | 1 1598 2 | ID1 | 2 1599 3 | ID2 | 4 1600 4 | ID3 | 8 1601 5 | ID4 | 16 1602 6 | ID5 | 32 1603 7 | ID6 | 64 1604 8 | ID7 | 128 1605 1606Some Examples:: 1607 1608 Switch | Hex | Decimal 1609 8 7 6 5 4 3 2 1 | Node ID | Node ID 1610 ----------------|---------|--------- 1611 0 0 0 0 0 0 0 0 | not allowed 1612 0 0 0 0 0 0 0 1 | 1 | 1 1613 0 0 0 0 0 0 1 0 | 2 | 2 1614 0 0 0 0 0 0 1 1 | 3 | 3 1615 . . . | | 1616 0 1 0 1 0 1 0 1 | 55 | 85 1617 . . . | | 1618 1 0 1 0 1 0 1 0 | AA | 170 1619 . . . | | 1620 1 1 1 1 1 1 0 1 | FD | 253 1621 1 1 1 1 1 1 1 0 | FE | 254 1622 1 1 1 1 1 1 1 1 | FF | 255 1623 1624 1625Setting the I/O Base Address 1626^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1627 1628The first six switches in switch block SW1 are used to select the I/O Base 1629address using the following table:: 1630 1631 Switch | Hex I/O 1632 1 2 3 4 5 6 | Address 1633 ------------------------|-------- 1634 OFF ON ON OFF OFF ON | 260 1635 OFF ON OFF ON ON OFF | 290 1636 OFF ON OFF OFF OFF ON | 2E0 (Manufacturer's default) 1637 OFF ON OFF OFF OFF OFF | 2F0 1638 OFF OFF ON ON ON ON | 300 1639 OFF OFF ON OFF ON OFF | 350 1640 OFF OFF OFF ON ON ON | 380 1641 OFF OFF OFF OFF OFF ON | 3E0 1642 1643Note: Other IO-Base addresses seem to be selectable, but only the above 1644 combinations are documented. 1645 1646 1647Setting the Base Memory (RAM) buffer Address 1648^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1649 1650The switches 7-10 of switch block SW1 are used to select the Memory 1651Base address of the RAM (2K) and the PROM:: 1652 1653 Switch | Hex RAM | Hex ROM 1654 7 8 9 10 | Address | Address 1655 ----------------|---------|----------- 1656 OFF OFF ON ON | C0000 | C8000 1657 OFF OFF ON OFF | D0000 | D8000 (Default) 1658 OFF OFF OFF ON | E0000 | E8000 1659 1660.. note:: 1661 1662 Other MEM-Base addresses seem to be selectable, but only the above 1663 combinations are documented. 1664 1665 1666Setting the Interrupt Line 1667^^^^^^^^^^^^^^^^^^^^^^^^^^ 1668 1669To select a hardware interrupt level install one (only one!) of the jumpers 1670JP3 through JP13 using the following table:: 1671 1672 Jumper | IRQ 1673 -------|----------------- 1674 3 | 14 1675 4 | 15 1676 5 | 12 1677 6 | 11 1678 7 | 10 1679 8 | 3 1680 9 | 4 1681 10 | 5 1682 11 | 6 1683 12 | 7 1684 13 | 2 (=9) Default! 1685 1686.. note:: 1687 1688 - Do not use JP11=IRQ6, it may conflict with your Floppy Disk 1689 Controller 1690 - Use JP3=IRQ14 only, if you don't have an IDE-, MFM-, or RLL- 1691 Hard Disk, it may conflict with their controllers 1692 1693 1694Setting the Timeout Parameters 1695------------------------------ 1696 1697The jumpers labeled JP1 and JP2 are used to determine the timeout 1698parameters. These two jumpers are normally left open. 1699 1700 1701Lantech 1702======= 1703 17048-bit card, unknown model 1705------------------------- 1706 - from Vlad Lungu <vlungu@ugal.ro> - his e-mail address seemed broken at 1707 the time I tried to reach him. Sorry Vlad, if you didn't get my reply. 1708 1709:: 1710 1711 ________________________________________________________________ 1712 | 1 8 | 1713 | ___________ __| 1714 | | SW1 | LED |__| 1715 | |__________| | 1716 | ___| 1717 | _____________________ |S | 8 1718 | | | |W | 1719 | | | |2 | 1720 | | | |__| 1 1721 | | UM9065L | |o| JP4 ____|____ 1722 | | | |o| | CN | 1723 | | | |________| 1724 | | | | 1725 | |___________________| | 1726 | | 1727 | | 1728 | _____________ | 1729 | | | | 1730 | | PROM | |ooooo| JP6 | 1731 | |____________| |ooooo| | 1732 |_____________ _ _| 1733 |____________________________________________| |__| 1734 1735 1736UM9065L : ARCnet Controller 1737 1738SW 1 : Shared Memory Address and I/O Base 1739 1740:: 1741 1742 ON=0 1743 1744 12345|Memory Address 1745 -----|-------------- 1746 00001| D4000 1747 00010| CC000 1748 00110| D0000 1749 01110| D1000 1750 01101| D9000 1751 10010| CC800 1752 10011| DC800 1753 11110| D1800 1754 1755It seems that the bits are considered in reverse order. Also, you must 1756observe that some of those addresses are unusual and I didn't probe them; I 1757used a memory dump in DOS to identify them. For the 00000 configuration and 1758some others that I didn't write here the card seems to conflict with the 1759video card (an S3 GENDAC). I leave the full decoding of those addresses to 1760you. 1761 1762:: 1763 1764 678| I/O Address 1765 ---|------------ 1766 000| 260 1767 001| failed probe 1768 010| 2E0 1769 011| 380 1770 100| 290 1771 101| 350 1772 110| failed probe 1773 111| 3E0 1774 1775 SW 2 : Node ID (binary coded) 1776 1777 JP 4 : Boot PROM enable CLOSE - enabled 1778 OPEN - disabled 1779 1780 JP 6 : IRQ set (ONLY ONE jumper on 1-5 for IRQ 2-6) 1781 1782 1783Acer 1784==== 1785 17868-bit card, Model 5210-003 1787-------------------------- 1788 1789 - from Vojtech Pavlik <vojtech@suse.cz> using portions of the existing 1790 arcnet-hardware file. 1791 1792This is a 90C26 based card. Its configuration seems similar to the SMC 1793PC100, but has some additional jumpers I don't know the meaning of. 1794 1795:: 1796 1797 __ 1798 | | 1799 ___________|__|_________________________ 1800 | | | | 1801 | | BNC | | 1802 | |______| ___| 1803 | _____________________ |___ 1804 | | | | 1805 | | Hybrid IC | | 1806 | | | o|o J1 | 1807 | |_____________________| 8|8 | 1808 | 8|8 J5 | 1809 | o|o | 1810 | 8|8 | 1811 |__ 8|8 | 1812 (|__| LED o|o | 1813 | 8|8 | 1814 | 8|8 J15 | 1815 | | 1816 | _____ | 1817 | | | _____ | 1818 | | | | | ___| 1819 | | | | | | 1820 | _____ | ROM | | UFS | | 1821 | | | | | | | | 1822 | | | ___ | | | | | 1823 | | | | | |__.__| |__.__| | 1824 | | NCR | |XTL| _____ _____ | 1825 | | | |___| | | | | | 1826 | |90C26| | | | | | 1827 | | | | RAM | | UFS | | 1828 | | | J17 o|o | | | | | 1829 | | | J16 o|o | | | | | 1830 | |__.__| |__.__| |__.__| | 1831 | ___ | 1832 | | |8 | 1833 | |SW2| | 1834 | | | | 1835 | |___|1 | 1836 | ___ | 1837 | | |10 J18 o|o | 1838 | | | o|o | 1839 | |SW1| o|o | 1840 | | | J21 o|o | 1841 | |___|1 | 1842 | | 1843 |____________________________________| 1844 1845 1846Legend:: 1847 1848 90C26 ARCNET Chip 1849 XTL 20 MHz Crystal 1850 SW1 1-6 Base I/O Address Select 1851 7-10 Memory Address Select 1852 SW2 1-8 Node ID Select (ID0-ID7) 1853 J1-J5 IRQ Select 1854 J6-J21 Unknown (Probably extra timeouts & ROM enable ...) 1855 LED1 Activity LED 1856 BNC Coax connector (STAR ARCnet) 1857 RAM 2k of SRAM 1858 ROM Boot ROM socket 1859 UFS Unidentified Flying Sockets 1860 1861 1862Setting the Node ID 1863^^^^^^^^^^^^^^^^^^^ 1864 1865The eight switches in SW2 are used to set the node ID. Each node attached 1866to the network must have an unique node ID which must not be 0. 1867Switch 1 (ID0) serves as the least significant bit (LSB). 1868 1869Setting one of the switches to OFF means "1", ON means "0". 1870 1871The node ID is the sum of the values of all switches set to "1" 1872These values are:: 1873 1874 Switch | Value 1875 -------|------- 1876 1 | 1 1877 2 | 2 1878 3 | 4 1879 4 | 8 1880 5 | 16 1881 6 | 32 1882 7 | 64 1883 8 | 128 1884 1885Don't set this to 0 or 255; these values are reserved. 1886 1887 1888Setting the I/O Base Address 1889^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1890 1891The switches 1 to 6 of switch block SW1 are used to select one 1892of 32 possible I/O Base addresses using the following tables:: 1893 1894 | Hex 1895 Switch | Value 1896 -------|------- 1897 1 | 200 1898 2 | 100 1899 3 | 80 1900 4 | 40 1901 5 | 20 1902 6 | 10 1903 1904The I/O address is sum of all switches set to "1". Remember that 1905the I/O address space bellow 0x200 is RESERVED for mainboard, so 1906switch 1 should be ALWAYS SET TO OFF. 1907 1908 1909Setting the Base Memory (RAM) buffer Address 1910^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1911 1912The memory buffer (RAM) requires 2K. The base of this buffer can be 1913located in any of sixteen positions. However, the addresses below 1914A0000 are likely to cause system hang because there's main RAM. 1915 1916Jumpers 7-10 of switch block SW1 select the Memory Base address:: 1917 1918 Switch | Hex RAM 1919 7 8 9 10 | Address 1920 ----------------|--------- 1921 OFF OFF OFF OFF | F0000 (conflicts with main BIOS) 1922 OFF OFF OFF ON | E0000 1923 OFF OFF ON OFF | D0000 1924 OFF OFF ON ON | C0000 (conflicts with video BIOS) 1925 OFF ON OFF OFF | B0000 (conflicts with mono video) 1926 OFF ON OFF ON | A0000 (conflicts with graphics) 1927 1928 1929Setting the Interrupt Line 1930^^^^^^^^^^^^^^^^^^^^^^^^^^ 1931 1932Jumpers 1-5 of the jumper block J1 control the IRQ level. ON means 1933shorted, OFF means open:: 1934 1935 Jumper | IRQ 1936 1 2 3 4 5 | 1937 ---------------------------- 1938 ON OFF OFF OFF OFF | 7 1939 OFF ON OFF OFF OFF | 5 1940 OFF OFF ON OFF OFF | 4 1941 OFF OFF OFF ON OFF | 3 1942 OFF OFF OFF OFF ON | 2 1943 1944 1945Unknown jumpers & sockets 1946^^^^^^^^^^^^^^^^^^^^^^^^^ 1947 1948I know nothing about these. I just guess that J16&J17 are timeout 1949jumpers and maybe one of J18-J21 selects ROM. Also J6-J10 and 1950J11-J15 are connecting IRQ2-7 to some pins on the UFSs. I can't 1951guess the purpose. 1952 1953Datapoint? 1954========== 1955 1956LAN-ARC-8, an 8-bit card 1957------------------------ 1958 1959 - from Vojtech Pavlik <vojtech@suse.cz> 1960 1961This is another SMC 90C65-based ARCnet card. I couldn't identify the 1962manufacturer, but it might be DataPoint, because the card has the 1963original arcNet logo in its upper right corner. 1964 1965:: 1966 1967 _______________________________________________________ 1968 | _________ | 1969 | | SW2 | ON arcNet | 1970 | |_________| OFF ___| 1971 | _____________ 1 ______ 8 | | 8 1972 | | | SW1 | XTAL | ____________ | S | 1973 | > RAM (2k) | |______|| | | W | 1974 | |_____________| | H | | 3 | 1975 | _________|_____ y | |___| 1 1976 | _________ | | |b | | 1977 | |_________| | | |r | | 1978 | | SMC | |i | | 1979 | | 90C65| |d | | 1980 | _________ | | | | | 1981 | | SW1 | ON | | |I | | 1982 | |_________| OFF |_________|_____/C | _____| 1983 | 1 8 | | | |___ 1984 | ______________ | | | BNC |___| 1985 | | | |____________| |_____| 1986 | > EPROM SOCKET | _____________ | 1987 | |______________| |_____________| | 1988 | ______________| 1989 | | 1990 |________________________________________| 1991 1992Legend:: 1993 1994 90C65 ARCNET Chip 1995 SW1 1-5: Base Memory Address Select 1996 6-8: Base I/O Address Select 1997 SW2 1-8: Node ID Select 1998 SW3 1-5: IRQ Select 1999 6-7: Extra Timeout 2000 8 : ROM Enable 2001 BNC Coax connector 2002 XTAL 20 MHz Crystal 2003 2004 2005Setting the Node ID 2006^^^^^^^^^^^^^^^^^^^ 2007 2008The eight switches in SW3 are used to set the node ID. Each node attached 2009to the network must have an unique node ID which must not be 0. 2010Switch 1 serves as the least significant bit (LSB). 2011 2012Setting one of the switches to Off means "1", On means "0". 2013 2014The node ID is the sum of the values of all switches set to "1" 2015These values are:: 2016 2017 Switch | Value 2018 -------|------- 2019 1 | 1 2020 2 | 2 2021 3 | 4 2022 4 | 8 2023 5 | 16 2024 6 | 32 2025 7 | 64 2026 8 | 128 2027 2028 2029Setting the I/O Base Address 2030^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2031 2032The last three switches in switch block SW1 are used to select one 2033of eight possible I/O Base addresses using the following table:: 2034 2035 2036 Switch | Hex I/O 2037 6 7 8 | Address 2038 ------------|-------- 2039 ON ON ON | 260 2040 OFF ON ON | 290 2041 ON OFF ON | 2E0 (Manufacturer's default) 2042 OFF OFF ON | 2F0 2043 ON ON OFF | 300 2044 OFF ON OFF | 350 2045 ON OFF OFF | 380 2046 OFF OFF OFF | 3E0 2047 2048 2049Setting the Base Memory (RAM) buffer Address 2050^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2051 2052The memory buffer (RAM) requires 2K. The base of this buffer can be 2053located in any of eight positions. The address of the Boot Prom is 2054memory base + 0x2000. 2055 2056Jumpers 3-5 of switch block SW1 select the Memory Base address. 2057 2058:: 2059 2060 Switch | Hex RAM | Hex ROM 2061 1 2 3 4 5 | Address | Address *) 2062 --------------------|---------|----------- 2063 ON ON ON ON ON | C0000 | C2000 2064 ON ON OFF ON ON | C4000 | C6000 2065 ON ON ON OFF ON | CC000 | CE000 2066 ON ON OFF OFF ON | D0000 | D2000 (Manufacturer's default) 2067 ON ON ON ON OFF | D4000 | D6000 2068 ON ON OFF ON OFF | D8000 | DA000 2069 ON ON ON OFF OFF | DC000 | DE000 2070 ON ON OFF OFF OFF | E0000 | E2000 2071 2072 *) To enable the Boot ROM set the switch 8 of switch block SW3 to position ON. 2073 2074The switches 1 and 2 probably add 0x0800 and 0x1000 to RAM base address. 2075 2076 2077Setting the Interrupt Line 2078^^^^^^^^^^^^^^^^^^^^^^^^^^ 2079 2080Switches 1-5 of the switch block SW3 control the IRQ level:: 2081 2082 Jumper | IRQ 2083 1 2 3 4 5 | 2084 ---------------------------- 2085 ON OFF OFF OFF OFF | 3 2086 OFF ON OFF OFF OFF | 4 2087 OFF OFF ON OFF OFF | 5 2088 OFF OFF OFF ON OFF | 7 2089 OFF OFF OFF OFF ON | 2 2090 2091 2092Setting the Timeout Parameters 2093^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2094 2095The switches 6-7 of the switch block SW3 are used to determine the timeout 2096parameters. These two switches are normally left in the OFF position. 2097 2098 2099Topware 2100======= 2101 21028-bit card, TA-ARC/10 2103--------------------- 2104 2105 - from Vojtech Pavlik <vojtech@suse.cz> 2106 2107This is another very similar 90C65 card. Most of the switches and jumpers 2108are the same as on other clones. 2109 2110:: 2111 2112 _____________________________________________________________________ 2113 | ___________ | | ______ | 2114 | |SW2 NODE ID| | | | XTAL | | 2115 | |___________| | Hybrid IC | |______| | 2116 | ___________ | | __| 2117 | |SW1 MEM+I/O| |_________________________| LED1|__|) 2118 | |___________| 1 2 | 2119 | J3 |o|o| TIMEOUT ______| 2120 | ______________ |o|o| | | 2121 | | | ___________________ | RJ | 2122 | > EPROM SOCKET | | \ |------| 2123 |J2 |______________| | | | | 2124 ||o| | | |______| 2125 ||o| ROM ENABLE | SMC | _________ | 2126 | _____________ | 90C65 | |_________| _____| 2127 | | | | | | |___ 2128 | > RAM (2k) | | | | BNC |___| 2129 | |_____________| | | |_____| 2130 | |____________________| | 2131 | ________ IRQ 2 3 4 5 7 ___________ | 2132 ||________| |o|o|o|o|o| |___________| | 2133 |________ J1|o|o|o|o|o| ______________| 2134 | | 2135 |_____________________________________________| 2136 2137Legend:: 2138 2139 90C65 ARCNET Chip 2140 XTAL 20 MHz Crystal 2141 SW1 1-5 Base Memory Address Select 2142 6-8 Base I/O Address Select 2143 SW2 1-8 Node ID Select (ID0-ID7) 2144 J1 IRQ Select 2145 J2 ROM Enable 2146 J3 Extra Timeout 2147 LED1 Activity LED 2148 BNC Coax connector (BUS ARCnet) 2149 RJ Twisted Pair Connector (daisy chain) 2150 2151 2152Setting the Node ID 2153^^^^^^^^^^^^^^^^^^^ 2154 2155The eight switches in SW2 are used to set the node ID. Each node attached to 2156the network must have an unique node ID which must not be 0. Switch 1 (ID0) 2157serves as the least significant bit (LSB). 2158 2159Setting one of the switches to Off means "1", On means "0". 2160 2161The node ID is the sum of the values of all switches set to "1" 2162These values are:: 2163 2164 Switch | Label | Value 2165 -------|-------|------- 2166 1 | ID0 | 1 2167 2 | ID1 | 2 2168 3 | ID2 | 4 2169 4 | ID3 | 8 2170 5 | ID4 | 16 2171 6 | ID5 | 32 2172 7 | ID6 | 64 2173 8 | ID7 | 128 2174 2175Setting the I/O Base Address 2176^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2177 2178The last three switches in switch block SW1 are used to select one 2179of eight possible I/O Base addresses using the following table:: 2180 2181 2182 Switch | Hex I/O 2183 6 7 8 | Address 2184 ------------|-------- 2185 ON ON ON | 260 (Manufacturer's default) 2186 OFF ON ON | 290 2187 ON OFF ON | 2E0 2188 OFF OFF ON | 2F0 2189 ON ON OFF | 300 2190 OFF ON OFF | 350 2191 ON OFF OFF | 380 2192 OFF OFF OFF | 3E0 2193 2194 2195Setting the Base Memory (RAM) buffer Address 2196^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2197 2198The memory buffer (RAM) requires 2K. The base of this buffer can be 2199located in any of eight positions. The address of the Boot Prom is 2200memory base + 0x2000. 2201 2202Jumpers 3-5 of switch block SW1 select the Memory Base address. 2203 2204:: 2205 2206 Switch | Hex RAM | Hex ROM 2207 1 2 3 4 5 | Address | Address *) 2208 --------------------|---------|----------- 2209 ON ON ON ON ON | C0000 | C2000 2210 ON ON OFF ON ON | C4000 | C6000 (Manufacturer's default) 2211 ON ON ON OFF ON | CC000 | CE000 2212 ON ON OFF OFF ON | D0000 | D2000 2213 ON ON ON ON OFF | D4000 | D6000 2214 ON ON OFF ON OFF | D8000 | DA000 2215 ON ON ON OFF OFF | DC000 | DE000 2216 ON ON OFF OFF OFF | E0000 | E2000 2217 2218 *) To enable the Boot ROM short the jumper J2. 2219 2220The jumpers 1 and 2 probably add 0x0800 and 0x1000 to RAM address. 2221 2222 2223Setting the Interrupt Line 2224^^^^^^^^^^^^^^^^^^^^^^^^^^ 2225 2226Jumpers 1-5 of the jumper block J1 control the IRQ level. ON means 2227shorted, OFF means open:: 2228 2229 Jumper | IRQ 2230 1 2 3 4 5 | 2231 ---------------------------- 2232 ON OFF OFF OFF OFF | 2 2233 OFF ON OFF OFF OFF | 3 2234 OFF OFF ON OFF OFF | 4 2235 OFF OFF OFF ON OFF | 5 2236 OFF OFF OFF OFF ON | 7 2237 2238 2239Setting the Timeout Parameters 2240^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2241 2242The jumpers J3 are used to set the timeout parameters. These two 2243jumpers are normally left open. 2244 2245Thomas-Conrad 2246============= 2247 2248Model #500-6242-0097 REV A (8-bit card) 2249--------------------------------------- 2250 2251 - from Lars Karlsson <100617.3473@compuserve.com> 2252 2253:: 2254 2255 ________________________________________________________ 2256 | ________ ________ |_____ 2257 | |........| |........| | 2258 | |________| |________| ___| 2259 | SW 3 SW 1 | | 2260 | Base I/O Base Addr. Station | | 2261 | address | | 2262 | ______ switch | | 2263 | | | | | 2264 | | | |___| 2265 | | | ______ |___._ 2266 | |______| |______| ____| BNC 2267 | Jumper- _____| Connector 2268 | Main chip block _ __| ' 2269 | | | | RJ Connector 2270 | |_| | with 110 Ohm 2271 | |__ Terminator 2272 | ___________ __| 2273 | |...........| | RJ-jack 2274 | |...........| _____ | (unused) 2275 | |___________| |_____| |__ 2276 | Boot PROM socket IRQ-jumpers |_ Diagnostic 2277 |________ __ _| LED (red) 2278 | | | | | | | | | | | | | | | | | | | | | | 2279 | | | | | | | | | | | | | | | | | | | | |________| 2280 | 2281 | 2282 2283And here are the settings for some of the switches and jumpers on the cards. 2284 2285:: 2286 2287 I/O 2288 2289 1 2 3 4 5 6 7 8 2290 2291 2E0----- 0 0 0 1 0 0 0 1 2292 2F0----- 0 0 0 1 0 0 0 0 2293 300----- 0 0 0 0 1 1 1 1 2294 350----- 0 0 0 0 1 1 1 0 2295 2296"0" in the above example means switch is off "1" means that it is on. 2297 2298:: 2299 2300 ShMem address. 2301 2302 1 2 3 4 5 6 7 8 2303 2304 CX00--0 0 1 1 | | | 2305 DX00--0 0 1 0 | 2306 X000--------- 1 1 | 2307 X400--------- 1 0 | 2308 X800--------- 0 1 | 2309 XC00--------- 0 0 2310 ENHANCED----------- 1 2311 COMPATIBLE--------- 0 2312 2313:: 2314 2315 IRQ 2316 2317 2318 3 4 5 7 2 2319 . . . . . 2320 . . . . . 2321 2322 2323There is a DIP-switch with 8 switches, used to set the shared memory address 2324to be used. The first 6 switches set the address, the 7th doesn't have any 2325function, and the 8th switch is used to select "compatible" or "enhanced". 2326When I got my two cards, one of them had this switch set to "enhanced". That 2327card didn't work at all, it wasn't even recognized by the driver. The other 2328card had this switch set to "compatible" and it behaved absolutely normally. I 2329guess that the switch on one of the cards, must have been changed accidentally 2330when the card was taken out of its former host. The question remains 2331unanswered, what is the purpose of the "enhanced" position? 2332 2333[Avery's note: "enhanced" probably either disables shared memory (use IO 2334ports instead) or disables IO ports (use memory addresses instead). This 2335varies by the type of card involved. I fail to see how either of these 2336enhance anything. Send me more detailed information about this mode, or 2337just use "compatible" mode instead.] 2338 2339Waterloo Microsystems Inc. ?? 2340============================= 2341 23428-bit card (C) 1985 2343------------------- 2344 - from Robert Michael Best <rmb117@cs.usask.ca> 2345 2346[Avery's note: these don't work with my driver for some reason. These cards 2347SEEM to have settings similar to the PDI508Plus, which is 2348software-configured and doesn't work with my driver either. The "Waterloo 2349chip" is a boot PROM, probably designed specifically for the University of 2350Waterloo. If you have any further information about this card, please 2351e-mail me.] 2352 2353The probe has not been able to detect the card on any of the J2 settings, 2354and I tried them again with the "Waterloo" chip removed. 2355 2356:: 2357 2358 _____________________________________________________________________ 2359 | \/ \/ ___ __ __ | 2360 | C4 C4 |^| | M || ^ ||^| | 2361 | -- -- |_| | 5 || || | C3 | 2362 | \/ \/ C10 |___|| ||_| | 2363 | C4 C4 _ _ | | ?? | 2364 | -- -- | \/ || | | 2365 | | || | | 2366 | | || C1 | | 2367 | | || | \/ _____| 2368 | | C6 || | C9 | |___ 2369 | | || | -- | BNC |___| 2370 | | || | >C7| |_____| 2371 | | || | | 2372 | __ __ |____||_____| 1 2 3 6 | 2373 || ^ | >C4| |o|o|o|o|o|o| J2 >C4| | 2374 || | |o|o|o|o|o|o| | 2375 || C2 | >C4| >C4| | 2376 || | >C8| | 2377 || | 2 3 4 5 6 7 IRQ >C4| | 2378 ||_____| |o|o|o|o|o|o| J3 | 2379 |_______ |o|o|o|o|o|o| _______________| 2380 | | 2381 |_____________________________________________| 2382 2383 C1 -- "COM9026 2384 SMC 8638" 2385 In a chip socket. 2386 2387 C2 -- "@Copyright 2388 Waterloo Microsystems Inc. 2389 1985" 2390 In a chip Socket with info printed on a label covering a round window 2391 showing the circuit inside. (The window indicates it is an EPROM chip.) 2392 2393 C3 -- "COM9032 2394 SMC 8643" 2395 In a chip socket. 2396 2397 C4 -- "74LS" 2398 9 total no sockets. 2399 2400 M5 -- "50006-136 2401 20.000000 MHZ 2402 MTQ-T1-S3 2403 0 M-TRON 86-40" 2404 Metallic case with 4 pins, no socket. 2405 2406 C6 -- "MOSTEK@TC8643 2407 MK6116N-20 2408 MALAYSIA" 2409 No socket. 2410 2411 C7 -- No stamp or label but in a 20 pin chip socket. 2412 2413 C8 -- "PAL10L8CN 2414 8623" 2415 In a 20 pin socket. 2416 2417 C9 -- "PAl16R4A-2CN 2418 8641" 2419 In a 20 pin socket. 2420 2421 C10 -- "M8640 2422 NMC 2423 9306N" 2424 In an 8 pin socket. 2425 2426 ?? -- Some components on a smaller board and attached with 20 pins all 2427 along the side closest to the BNC connector. The are coated in a dark 2428 resin. 2429 2430On the board there are two jumper banks labeled J2 and J3. The 2431manufacturer didn't put a J1 on the board. The two boards I have both 2432came with a jumper box for each bank. 2433 2434:: 2435 2436 J2 -- Numbered 1 2 3 4 5 6. 2437 4 and 5 are not stamped due to solder points. 2438 2439 J3 -- IRQ 2 3 4 5 6 7 2440 2441The board itself has a maple leaf stamped just above the irq jumpers 2442and "-2 46-86" beside C2. Between C1 and C6 "ASS 'Y 300163" and "@1986 2443CORMAN CUSTOM ELECTRONICS CORP." stamped just below the BNC connector. 2444Below that "MADE IN CANADA" 2445 2446No Name 2447======= 2448 24498-bit cards, 16-bit cards 2450------------------------- 2451 2452 - from Juergen Seifert <seifert@htwm.de> 2453 2454I have named this ARCnet card "NONAME", since there is no name of any 2455manufacturer on the Installation manual nor on the shipping box. The only 2456hint to the existence of a manufacturer at all is written in copper, 2457it is "Made in Taiwan" 2458 2459This description has been written by Juergen Seifert <seifert@htwm.de> 2460using information from the Original 2461 2462 "ARCnet Installation Manual" 2463 2464:: 2465 2466 ________________________________________________________________ 2467 | |STAR| BUS| T/P| | 2468 | |____|____|____| | 2469 | _____________________ | 2470 | | | | 2471 | | | | 2472 | | | | 2473 | | SMC | | 2474 | | | | 2475 | | COM90C65 | | 2476 | | | | 2477 | | | | 2478 | |__________-__________| | 2479 | _____| 2480 | _______________ | CN | 2481 | | PROM | |_____| 2482 | > SOCKET | | 2483 | |_______________| 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 | 2484 | _______________ _______________ | 2485 | |o|o|o|o|o|o|o|o| | SW1 || SW2 || 2486 | |o|o|o|o|o|o|o|o| |_______________||_______________|| 2487 |___ 2 3 4 5 7 E E R Node ID IOB__|__MEM____| 2488 | \ IRQ / T T O | 2489 |__________________1_2_M______________________| 2490 2491Legend:: 2492 2493 COM90C65: ARCnet Probe 2494 S1 1-8: Node ID Select 2495 S2 1-3: I/O Base Address Select 2496 4-6: Memory Base Address Select 2497 7-8: RAM Offset Select 2498 ET1, ET2 Extended Timeout Select 2499 ROM ROM Enable Select 2500 CN RG62 Coax Connector 2501 STAR| BUS | T/P Three fields for placing a sign (colored circle) 2502 indicating the topology of the card 2503 2504Setting one of the switches to Off means "1", On means "0". 2505 2506 2507Setting the Node ID 2508^^^^^^^^^^^^^^^^^^^ 2509 2510The eight switches in group SW1 are used to set the node ID. 2511Each node attached to the network must have an unique node ID which 2512must be different from 0. 2513Switch 8 serves as the least significant bit (LSB). 2514 2515The node ID is the sum of the values of all switches set to "1" 2516These values are:: 2517 2518 Switch | Value 2519 -------|------- 2520 8 | 1 2521 7 | 2 2522 6 | 4 2523 5 | 8 2524 4 | 16 2525 3 | 32 2526 2 | 64 2527 1 | 128 2528 2529Some Examples:: 2530 2531 Switch | Hex | Decimal 2532 1 2 3 4 5 6 7 8 | Node ID | Node ID 2533 ----------------|---------|--------- 2534 0 0 0 0 0 0 0 0 | not allowed 2535 0 0 0 0 0 0 0 1 | 1 | 1 2536 0 0 0 0 0 0 1 0 | 2 | 2 2537 0 0 0 0 0 0 1 1 | 3 | 3 2538 . . . | | 2539 0 1 0 1 0 1 0 1 | 55 | 85 2540 . . . | | 2541 1 0 1 0 1 0 1 0 | AA | 170 2542 . . . | | 2543 1 1 1 1 1 1 0 1 | FD | 253 2544 1 1 1 1 1 1 1 0 | FE | 254 2545 1 1 1 1 1 1 1 1 | FF | 255 2546 2547 2548Setting the I/O Base Address 2549^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2550 2551The first three switches in switch group SW2 are used to select one 2552of eight possible I/O Base addresses using the following table:: 2553 2554 Switch | Hex I/O 2555 1 2 3 | Address 2556 ------------|-------- 2557 ON ON ON | 260 2558 ON ON OFF | 290 2559 ON OFF ON | 2E0 (Manufacturer's default) 2560 ON OFF OFF | 2F0 2561 OFF ON ON | 300 2562 OFF ON OFF | 350 2563 OFF OFF ON | 380 2564 OFF OFF OFF | 3E0 2565 2566 2567Setting the Base Memory (RAM) buffer Address 2568^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2569 2570The memory buffer requires 2K of a 16K block of RAM. The base of this 257116K block can be located in any of eight positions. 2572Switches 4-6 of switch group SW2 select the Base of the 16K block. 2573Within that 16K address space, the buffer may be assigned any one of four 2574positions, determined by the offset, switches 7 and 8 of group SW2. 2575 2576:: 2577 2578 Switch | Hex RAM | Hex ROM 2579 4 5 6 7 8 | Address | Address *) 2580 -----------|---------|----------- 2581 0 0 0 0 0 | C0000 | C2000 2582 0 0 0 0 1 | C0800 | C2000 2583 0 0 0 1 0 | C1000 | C2000 2584 0 0 0 1 1 | C1800 | C2000 2585 | | 2586 0 0 1 0 0 | C4000 | C6000 2587 0 0 1 0 1 | C4800 | C6000 2588 0 0 1 1 0 | C5000 | C6000 2589 0 0 1 1 1 | C5800 | C6000 2590 | | 2591 0 1 0 0 0 | CC000 | CE000 2592 0 1 0 0 1 | CC800 | CE000 2593 0 1 0 1 0 | CD000 | CE000 2594 0 1 0 1 1 | CD800 | CE000 2595 | | 2596 0 1 1 0 0 | D0000 | D2000 (Manufacturer's default) 2597 0 1 1 0 1 | D0800 | D2000 2598 0 1 1 1 0 | D1000 | D2000 2599 0 1 1 1 1 | D1800 | D2000 2600 | | 2601 1 0 0 0 0 | D4000 | D6000 2602 1 0 0 0 1 | D4800 | D6000 2603 1 0 0 1 0 | D5000 | D6000 2604 1 0 0 1 1 | D5800 | D6000 2605 | | 2606 1 0 1 0 0 | D8000 | DA000 2607 1 0 1 0 1 | D8800 | DA000 2608 1 0 1 1 0 | D9000 | DA000 2609 1 0 1 1 1 | D9800 | DA000 2610 | | 2611 1 1 0 0 0 | DC000 | DE000 2612 1 1 0 0 1 | DC800 | DE000 2613 1 1 0 1 0 | DD000 | DE000 2614 1 1 0 1 1 | DD800 | DE000 2615 | | 2616 1 1 1 0 0 | E0000 | E2000 2617 1 1 1 0 1 | E0800 | E2000 2618 1 1 1 1 0 | E1000 | E2000 2619 1 1 1 1 1 | E1800 | E2000 2620 2621 *) To enable the 8K Boot PROM install the jumper ROM. 2622 The default is jumper ROM not installed. 2623 2624 2625Setting Interrupt Request Lines (IRQ) 2626^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2627 2628To select a hardware interrupt level set one (only one!) of the jumpers 2629IRQ2, IRQ3, IRQ4, IRQ5 or IRQ7. The manufacturer's default is IRQ2. 2630 2631 2632Setting the Timeouts 2633^^^^^^^^^^^^^^^^^^^^ 2634 2635The two jumpers labeled ET1 and ET2 are used to determine the timeout 2636parameters (response and reconfiguration time). Every node in a network 2637must be set to the same timeout values. 2638 2639:: 2640 2641 ET1 ET2 | Response Time (us) | Reconfiguration Time (ms) 2642 --------|--------------------|-------------------------- 2643 Off Off | 78 | 840 (Default) 2644 Off On | 285 | 1680 2645 On Off | 563 | 1680 2646 On On | 1130 | 1680 2647 2648On means jumper installed, Off means jumper not installed 2649 2650 265116-BIT ARCNET 2652------------- 2653 2654The manual of my 8-Bit NONAME ARCnet Card contains another description 2655of a 16-Bit Coax / Twisted Pair Card. This description is incomplete, 2656because there are missing two pages in the manual booklet. (The table 2657of contents reports pages ... 2-9, 2-11, 2-12, 3-1, ... but inside 2658the booklet there is a different way of counting ... 2-9, 2-10, A-1, 2659(empty page), 3-1, ..., 3-18, A-1 (again), A-2) 2660Also the picture of the board layout is not as good as the picture of 26618-Bit card, because there isn't any letter like "SW1" written to the 2662picture. 2663 2664Should somebody have such a board, please feel free to complete this 2665description or to send a mail to me! 2666 2667This description has been written by Juergen Seifert <seifert@htwm.de> 2668using information from the Original 2669 2670 "ARCnet Installation Manual" 2671 2672:: 2673 2674 ___________________________________________________________________ 2675 < _________________ _________________ | 2676 > | SW? || SW? | | 2677 < |_________________||_________________| | 2678 > ____________________ | 2679 < | | | 2680 > | | | 2681 < | | | 2682 > | | | 2683 < | | | 2684 > | | | 2685 < | | | 2686 > |____________________| | 2687 < ____| 2688 > ____________________ | | 2689 < | | | J1 | 2690 > | < | | 2691 < |____________________| ? ? ? ? ? ? |____| 2692 > |o|o|o|o|o|o| | 2693 < |o|o|o|o|o|o| | 2694 > | 2695 < __ ___________| 2696 > | | | 2697 <____________| |_______________________________________| 2698 2699 2700Setting one of the switches to Off means "1", On means "0". 2701 2702 2703Setting the Node ID 2704^^^^^^^^^^^^^^^^^^^ 2705 2706The eight switches in group SW2 are used to set the node ID. 2707Each node attached to the network must have an unique node ID which 2708must be different from 0. 2709Switch 8 serves as the least significant bit (LSB). 2710 2711The node ID is the sum of the values of all switches set to "1" 2712These values are:: 2713 2714 Switch | Value 2715 -------|------- 2716 8 | 1 2717 7 | 2 2718 6 | 4 2719 5 | 8 2720 4 | 16 2721 3 | 32 2722 2 | 64 2723 1 | 128 2724 2725Some Examples:: 2726 2727 Switch | Hex | Decimal 2728 1 2 3 4 5 6 7 8 | Node ID | Node ID 2729 ----------------|---------|--------- 2730 0 0 0 0 0 0 0 0 | not allowed 2731 0 0 0 0 0 0 0 1 | 1 | 1 2732 0 0 0 0 0 0 1 0 | 2 | 2 2733 0 0 0 0 0 0 1 1 | 3 | 3 2734 . . . | | 2735 0 1 0 1 0 1 0 1 | 55 | 85 2736 . . . | | 2737 1 0 1 0 1 0 1 0 | AA | 170 2738 . . . | | 2739 1 1 1 1 1 1 0 1 | FD | 253 2740 1 1 1 1 1 1 1 0 | FE | 254 2741 1 1 1 1 1 1 1 1 | FF | 255 2742 2743 2744Setting the I/O Base Address 2745^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2746 2747The first three switches in switch group SW1 are used to select one 2748of eight possible I/O Base addresses using the following table:: 2749 2750 Switch | Hex I/O 2751 3 2 1 | Address 2752 ------------|-------- 2753 ON ON ON | 260 2754 ON ON OFF | 290 2755 ON OFF ON | 2E0 (Manufacturer's default) 2756 ON OFF OFF | 2F0 2757 OFF ON ON | 300 2758 OFF ON OFF | 350 2759 OFF OFF ON | 380 2760 OFF OFF OFF | 3E0 2761 2762 2763Setting the Base Memory (RAM) buffer Address 2764^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2765 2766The memory buffer requires 2K of a 16K block of RAM. The base of this 276716K block can be located in any of eight positions. 2768Switches 6-8 of switch group SW1 select the Base of the 16K block. 2769Within that 16K address space, the buffer may be assigned any one of four 2770positions, determined by the offset, switches 4 and 5 of group SW1:: 2771 2772 Switch | Hex RAM | Hex ROM 2773 8 7 6 5 4 | Address | Address 2774 -----------|---------|----------- 2775 0 0 0 0 0 | C0000 | C2000 2776 0 0 0 0 1 | C0800 | C2000 2777 0 0 0 1 0 | C1000 | C2000 2778 0 0 0 1 1 | C1800 | C2000 2779 | | 2780 0 0 1 0 0 | C4000 | C6000 2781 0 0 1 0 1 | C4800 | C6000 2782 0 0 1 1 0 | C5000 | C6000 2783 0 0 1 1 1 | C5800 | C6000 2784 | | 2785 0 1 0 0 0 | CC000 | CE000 2786 0 1 0 0 1 | CC800 | CE000 2787 0 1 0 1 0 | CD000 | CE000 2788 0 1 0 1 1 | CD800 | CE000 2789 | | 2790 0 1 1 0 0 | D0000 | D2000 (Manufacturer's default) 2791 0 1 1 0 1 | D0800 | D2000 2792 0 1 1 1 0 | D1000 | D2000 2793 0 1 1 1 1 | D1800 | D2000 2794 | | 2795 1 0 0 0 0 | D4000 | D6000 2796 1 0 0 0 1 | D4800 | D6000 2797 1 0 0 1 0 | D5000 | D6000 2798 1 0 0 1 1 | D5800 | D6000 2799 | | 2800 1 0 1 0 0 | D8000 | DA000 2801 1 0 1 0 1 | D8800 | DA000 2802 1 0 1 1 0 | D9000 | DA000 2803 1 0 1 1 1 | D9800 | DA000 2804 | | 2805 1 1 0 0 0 | DC000 | DE000 2806 1 1 0 0 1 | DC800 | DE000 2807 1 1 0 1 0 | DD000 | DE000 2808 1 1 0 1 1 | DD800 | DE000 2809 | | 2810 1 1 1 0 0 | E0000 | E2000 2811 1 1 1 0 1 | E0800 | E2000 2812 1 1 1 1 0 | E1000 | E2000 2813 1 1 1 1 1 | E1800 | E2000 2814 2815 2816Setting Interrupt Request Lines (IRQ) 2817^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2818 2819?????????????????????????????????????? 2820 2821 2822Setting the Timeouts 2823^^^^^^^^^^^^^^^^^^^^ 2824 2825?????????????????????????????????????? 2826 2827 28288-bit cards ("Made in Taiwan R.O.C.") 2829------------------------------------- 2830 2831 - from Vojtech Pavlik <vojtech@suse.cz> 2832 2833I have named this ARCnet card "NONAME", since I got only the card with 2834no manual at all and the only text identifying the manufacturer is 2835"MADE IN TAIWAN R.O.C" printed on the card. 2836 2837:: 2838 2839 ____________________________________________________________ 2840 | 1 2 3 4 5 6 7 8 | 2841 | |o|o| JP1 o|o|o|o|o|o|o|o| ON | 2842 | + o|o|o|o|o|o|o|o| ___| 2843 | _____________ o|o|o|o|o|o|o|o| OFF _____ | | ID7 2844 | | | SW1 | | | | ID6 2845 | > RAM (2k) | ____________________ | H | | S | ID5 2846 | |_____________| | || y | | W | ID4 2847 | | || b | | 2 | ID3 2848 | | || r | | | ID2 2849 | | || i | | | ID1 2850 | | 90C65 || d | |___| ID0 2851 | SW3 | || | | 2852 | |o|o|o|o|o|o|o|o| ON | || I | | 2853 | |o|o|o|o|o|o|o|o| | || C | | 2854 | |o|o|o|o|o|o|o|o| OFF |____________________|| | _____| 2855 | 1 2 3 4 5 6 7 8 | | | |___ 2856 | ______________ | | | BNC |___| 2857 | | | |_____| |_____| 2858 | > EPROM SOCKET | | 2859 | |______________| | 2860 | ______________| 2861 | | 2862 |_____________________________________________| 2863 2864Legend:: 2865 2866 90C65 ARCNET Chip 2867 SW1 1-5: Base Memory Address Select 2868 6-8: Base I/O Address Select 2869 SW2 1-8: Node ID Select (ID0-ID7) 2870 SW3 1-5: IRQ Select 2871 6-7: Extra Timeout 2872 8 : ROM Enable 2873 JP1 Led connector 2874 BNC Coax connector 2875 2876Although the jumpers SW1 and SW3 are marked SW, not JP, they are jumpers, not 2877switches. 2878 2879Setting the jumpers to ON means connecting the upper two pins, off the bottom 2880two - or - in case of IRQ setting, connecting none of them at all. 2881 2882Setting the Node ID 2883^^^^^^^^^^^^^^^^^^^ 2884 2885The eight switches in SW2 are used to set the node ID. Each node attached 2886to the network must have an unique node ID which must not be 0. 2887Switch 1 (ID0) serves as the least significant bit (LSB). 2888 2889Setting one of the switches to Off means "1", On means "0". 2890 2891The node ID is the sum of the values of all switches set to "1" 2892These values are:: 2893 2894 Switch | Label | Value 2895 -------|-------|------- 2896 1 | ID0 | 1 2897 2 | ID1 | 2 2898 3 | ID2 | 4 2899 4 | ID3 | 8 2900 5 | ID4 | 16 2901 6 | ID5 | 32 2902 7 | ID6 | 64 2903 8 | ID7 | 128 2904 2905Some Examples:: 2906 2907 Switch | Hex | Decimal 2908 8 7 6 5 4 3 2 1 | Node ID | Node ID 2909 ----------------|---------|--------- 2910 0 0 0 0 0 0 0 0 | not allowed 2911 0 0 0 0 0 0 0 1 | 1 | 1 2912 0 0 0 0 0 0 1 0 | 2 | 2 2913 0 0 0 0 0 0 1 1 | 3 | 3 2914 . . . | | 2915 0 1 0 1 0 1 0 1 | 55 | 85 2916 . . . | | 2917 1 0 1 0 1 0 1 0 | AA | 170 2918 . . . | | 2919 1 1 1 1 1 1 0 1 | FD | 253 2920 1 1 1 1 1 1 1 0 | FE | 254 2921 1 1 1 1 1 1 1 1 | FF | 255 2922 2923 2924Setting the I/O Base Address 2925^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2926 2927The last three switches in switch block SW1 are used to select one 2928of eight possible I/O Base addresses using the following table:: 2929 2930 2931 Switch | Hex I/O 2932 6 7 8 | Address 2933 ------------|-------- 2934 ON ON ON | 260 2935 OFF ON ON | 290 2936 ON OFF ON | 2E0 (Manufacturer's default) 2937 OFF OFF ON | 2F0 2938 ON ON OFF | 300 2939 OFF ON OFF | 350 2940 ON OFF OFF | 380 2941 OFF OFF OFF | 3E0 2942 2943 2944Setting the Base Memory (RAM) buffer Address 2945^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2946 2947The memory buffer (RAM) requires 2K. The base of this buffer can be 2948located in any of eight positions. The address of the Boot Prom is 2949memory base + 0x2000. 2950 2951Jumpers 3-5 of jumper block SW1 select the Memory Base address. 2952 2953:: 2954 2955 Switch | Hex RAM | Hex ROM 2956 1 2 3 4 5 | Address | Address *) 2957 --------------------|---------|----------- 2958 ON ON ON ON ON | C0000 | C2000 2959 ON ON OFF ON ON | C4000 | C6000 2960 ON ON ON OFF ON | CC000 | CE000 2961 ON ON OFF OFF ON | D0000 | D2000 (Manufacturer's default) 2962 ON ON ON ON OFF | D4000 | D6000 2963 ON ON OFF ON OFF | D8000 | DA000 2964 ON ON ON OFF OFF | DC000 | DE000 2965 ON ON OFF OFF OFF | E0000 | E2000 2966 2967 *) To enable the Boot ROM set the jumper 8 of jumper block SW3 to position ON. 2968 2969The jumpers 1 and 2 probably add 0x0800, 0x1000 and 0x1800 to RAM adders. 2970 2971Setting the Interrupt Line 2972^^^^^^^^^^^^^^^^^^^^^^^^^^ 2973 2974Jumpers 1-5 of the jumper block SW3 control the IRQ level:: 2975 2976 Jumper | IRQ 2977 1 2 3 4 5 | 2978 ---------------------------- 2979 ON OFF OFF OFF OFF | 2 2980 OFF ON OFF OFF OFF | 3 2981 OFF OFF ON OFF OFF | 4 2982 OFF OFF OFF ON OFF | 5 2983 OFF OFF OFF OFF ON | 7 2984 2985 2986Setting the Timeout Parameters 2987^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 2988 2989The jumpers 6-7 of the jumper block SW3 are used to determine the timeout 2990parameters. These two jumpers are normally left in the OFF position. 2991 2992 2993 2994(Generic Model 9058) 2995-------------------- 2996 - from Andrew J. Kroll <ag784@freenet.buffalo.edu> 2997 - Sorry this sat in my to-do box for so long, Andrew! (yikes - over a 2998 year!) 2999 3000:: 3001 3002 _____ 3003 | < 3004 | .---' 3005 ________________________________________________________________ | | 3006 | | SW2 | | | 3007 | ___________ |_____________| | | 3008 | | | 1 2 3 4 5 6 ___| | 3009 | > 6116 RAM | _________ 8 | | | 3010 | |___________| |20MHzXtal| 7 | | | 3011 | |_________| __________ 6 | S | | 3012 | 74LS373 | |- 5 | W | | 3013 | _________ | E |- 4 | | | 3014 | >_______| ______________|..... P |- 3 | 3 | | 3015 | | | : O |- 2 | | | 3016 | | | : X |- 1 |___| | 3017 | ________________ | | : Y |- | | 3018 | | SW1 | | SL90C65 | : |- | | 3019 | |________________| | | : B |- | | 3020 | 1 2 3 4 5 6 7 8 | | : O |- | | 3021 | |_________o____|..../ A |- _______| | 3022 | ____________________ | R |- | |------, 3023 | | | | D |- | BNC | # | 3024 | > 2764 PROM SOCKET | |__________|- |_______|------' 3025 | |____________________| _________ | | 3026 | >________| <- 74LS245 | | 3027 | | | 3028 |___ ______________| | 3029 |H H H H H H H H H H H H H H H H H H H H H H H| | | 3030 |U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U_U| | | 3031 \| 3032 3033Legend:: 3034 3035 SL90C65 ARCNET Controller / Transceiver /Logic 3036 SW1 1-5: IRQ Select 3037 6: ET1 3038 7: ET2 3039 8: ROM ENABLE 3040 SW2 1-3: Memory Buffer/PROM Address 3041 3-6: I/O Address Map 3042 SW3 1-8: Node ID Select 3043 BNC BNC RG62/U Connection 3044 *I* have had success using RG59B/U with *NO* terminators! 3045 What gives?! 3046 3047SW1: Timeouts, Interrupt and ROM 3048^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 3049 3050To select a hardware interrupt level set one (only one!) of the dip switches 3051up (on) SW1...(switches 1-5) 3052IRQ3, IRQ4, IRQ5, IRQ7, IRQ2. The Manufacturer's default is IRQ2. 3053 3054The switches on SW1 labeled EXT1 (switch 6) and EXT2 (switch 7) 3055are used to determine the timeout parameters. These two dip switches 3056are normally left off (down). 3057 3058 To enable the 8K Boot PROM position SW1 switch 8 on (UP) labeled ROM. 3059 The default is jumper ROM not installed. 3060 3061 3062Setting the I/O Base Address 3063^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 3064 3065The last three switches in switch group SW2 are used to select one 3066of eight possible I/O Base addresses using the following table:: 3067 3068 3069 Switch | Hex I/O 3070 4 5 6 | Address 3071 -------|-------- 3072 0 0 0 | 260 3073 0 0 1 | 290 3074 0 1 0 | 2E0 (Manufacturer's default) 3075 0 1 1 | 2F0 3076 1 0 0 | 300 3077 1 0 1 | 350 3078 1 1 0 | 380 3079 1 1 1 | 3E0 3080 3081 3082Setting the Base Memory Address (RAM & ROM) 3083^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 3084 3085The memory buffer requires 2K of a 16K block of RAM. The base of this 308616K block can be located in any of eight positions. 3087Switches 1-3 of switch group SW2 select the Base of the 16K block. 3088(0 = DOWN, 1 = UP) 3089I could, however, only verify two settings... 3090 3091 3092:: 3093 3094 Switch| Hex RAM | Hex ROM 3095 1 2 3 | Address | Address 3096 ------|---------|----------- 3097 0 0 0 | E0000 | E2000 3098 0 0 1 | D0000 | D2000 (Manufacturer's default) 3099 0 1 0 | ????? | ????? 3100 0 1 1 | ????? | ????? 3101 1 0 0 | ????? | ????? 3102 1 0 1 | ????? | ????? 3103 1 1 0 | ????? | ????? 3104 1 1 1 | ????? | ????? 3105 3106 3107Setting the Node ID 3108^^^^^^^^^^^^^^^^^^^ 3109 3110The eight switches in group SW3 are used to set the node ID. 3111Each node attached to the network must have an unique node ID which 3112must be different from 0. 3113Switch 1 serves as the least significant bit (LSB). 3114switches in the DOWN position are OFF (0) and in the UP position are ON (1) 3115 3116The node ID is the sum of the values of all switches set to "1" 3117These values are:: 3118 3119 Switch | Value 3120 -------|------- 3121 1 | 1 3122 2 | 2 3123 3 | 4 3124 4 | 8 3125 5 | 16 3126 6 | 32 3127 7 | 64 3128 8 | 128 3129 3130Some Examples:: 3131 3132 Switch# | Hex | Decimal 3133 8 7 6 5 4 3 2 1 | Node ID | Node ID 3134 ----------------|---------|--------- 3135 0 0 0 0 0 0 0 0 | not allowed <-. 3136 0 0 0 0 0 0 0 1 | 1 | 1 | 3137 0 0 0 0 0 0 1 0 | 2 | 2 | 3138 0 0 0 0 0 0 1 1 | 3 | 3 | 3139 . . . | | | 3140 0 1 0 1 0 1 0 1 | 55 | 85 | 3141 . . . | | + Don't use 0 or 255! 3142 1 0 1 0 1 0 1 0 | AA | 170 | 3143 . . . | | | 3144 1 1 1 1 1 1 0 1 | FD | 253 | 3145 1 1 1 1 1 1 1 0 | FE | 254 | 3146 1 1 1 1 1 1 1 1 | FF | 255 <-' 3147 3148 3149Tiara 3150===== 3151 3152(model unknown) 3153--------------- 3154 3155 - from Christoph Lameter <christoph@lameter.com> 3156 3157 3158Here is information about my card as far as I could figure it out:: 3159 3160 3161 ----------------------------------------------- tiara 3162 Tiara LanCard of Tiara Computer Systems. 3163 3164 +----------------------------------------------+ 3165 ! ! Transmitter Unit ! ! 3166 ! +------------------+ ------- 3167 ! MEM Coax Connector 3168 ! ROM 7654321 <- I/O ------- 3169 ! : : +--------+ ! 3170 ! : : ! 90C66LJ! +++ 3171 ! : : ! ! !D Switch to set 3172 ! : : ! ! !I the Nodenumber 3173 ! : : +--------+ !P 3174 ! !++ 3175 ! 234567 <- IRQ ! 3176 +------------!!!!!!!!!!!!!!!!!!!!!!!!--------+ 3177 !!!!!!!!!!!!!!!!!!!!!!!! 3178 3179- 0 = Jumper Installed 3180- 1 = Open 3181 3182Top Jumper line Bit 7 = ROM Enable 654=Memory location 321=I/O 3183 3184Settings for Memory Location (Top Jumper Line) 3185 3186=== ================ 3187456 Address selected 3188=== ================ 3189000 C0000 3190001 C4000 3191010 CC000 3192011 D0000 3193100 D4000 3194101 D8000 3195110 DC000 3196111 E0000 3197=== ================ 3198 3199Settings for I/O Address (Top Jumper Line) 3200 3201=== ==== 3202123 Port 3203=== ==== 3204000 260 3205001 290 3206010 2E0 3207011 2F0 3208100 300 3209101 350 3210110 380 3211111 3E0 3212=== ==== 3213 3214Settings for IRQ Selection (Lower Jumper Line) 3215 3216====== ===== 3217234567 3218====== ===== 3219011111 IRQ 2 3220101111 IRQ 3 3221110111 IRQ 4 3222111011 IRQ 5 3223111110 IRQ 7 3224====== ===== 3225 3226Other Cards 3227=========== 3228 3229I have no information on other models of ARCnet cards at the moment. Please 3230send any and all info to: 3231 3232 apenwarr@worldvisions.ca 3233 3234Thanks.