b53.rst (5282B)
1.. SPDX-License-Identifier: GPL-2.0 2 3========================================== 4Broadcom RoboSwitch Ethernet switch driver 5========================================== 6 7The Broadcom RoboSwitch Ethernet switch family is used in quite a range of 8xDSL router, cable modems and other multimedia devices. 9 10The actual implementation supports the devices BCM5325E, BCM5365, BCM539x, 11BCM53115 and BCM53125 as well as BCM63XX. 12 13Implementation details 14====================== 15 16The driver is located in ``drivers/net/dsa/b53/`` and is implemented as a 17DSA driver; see ``Documentation/networking/dsa/dsa.rst`` for details on the 18subsystem and what it provides. 19 20The switch is, if possible, configured to enable a Broadcom specific 4-bytes 21switch tag which gets inserted by the switch for every packet forwarded to the 22CPU interface, conversely, the CPU network interface should insert a similar 23tag for packets entering the CPU port. The tag format is described in 24``net/dsa/tag_brcm.c``. 25 26The configuration of the device depends on whether or not tagging is 27supported. 28 29The interface names and example network configuration are used according the 30configuration described in the :ref:`dsa-config-showcases`. 31 32Configuration with tagging support 33---------------------------------- 34 35The tagging based configuration is desired. It is not specific to the b53 36DSA driver and will work like all DSA drivers which supports tagging. 37 38See :ref:`dsa-tagged-configuration`. 39 40Configuration without tagging support 41------------------------------------- 42 43Older models (5325, 5365) support a different tag format that is not supported 44yet. 539x and 531x5 require managed mode and some special handling, which is 45also not yet supported. The tagging support is disabled in these cases and the 46switch need a different configuration. 47 48The configuration slightly differ from the :ref:`dsa-vlan-configuration`. 49 50The b53 tags the CPU port in all VLANs, since otherwise any PVID untagged 51VLAN programming would basically change the CPU port's default PVID and make 52it untagged, undesirable. 53 54In difference to the configuration described in :ref:`dsa-vlan-configuration` 55the default VLAN 1 has to be removed from the slave interface configuration in 56single port and gateway configuration, while there is no need to add an extra 57VLAN configuration in the bridge showcase. 58 59single port 60~~~~~~~~~~~ 61The configuration can only be set up via VLAN tagging and bridge setup. 62By default packages are tagged with vid 1: 63 64.. code-block:: sh 65 66 # tag traffic on CPU port 67 ip link add link eth0 name eth0.1 type vlan id 1 68 ip link add link eth0 name eth0.2 type vlan id 2 69 ip link add link eth0 name eth0.3 type vlan id 3 70 71 # The master interface needs to be brought up before the slave ports. 72 ip link set eth0 up 73 ip link set eth0.1 up 74 ip link set eth0.2 up 75 ip link set eth0.3 up 76 77 # bring up the slave interfaces 78 ip link set wan up 79 ip link set lan1 up 80 ip link set lan2 up 81 82 # create bridge 83 ip link add name br0 type bridge 84 85 # activate VLAN filtering 86 ip link set dev br0 type bridge vlan_filtering 1 87 88 # add ports to bridges 89 ip link set dev wan master br0 90 ip link set dev lan1 master br0 91 ip link set dev lan2 master br0 92 93 # tag traffic on ports 94 bridge vlan add dev lan1 vid 2 pvid untagged 95 bridge vlan del dev lan1 vid 1 96 bridge vlan add dev lan2 vid 3 pvid untagged 97 bridge vlan del dev lan2 vid 1 98 99 # configure the VLANs 100 ip addr add 192.0.2.1/30 dev eth0.1 101 ip addr add 192.0.2.5/30 dev eth0.2 102 ip addr add 192.0.2.9/30 dev eth0.3 103 104 # bring up the bridge devices 105 ip link set br0 up 106 107 108bridge 109~~~~~~ 110 111.. code-block:: sh 112 113 # tag traffic on CPU port 114 ip link add link eth0 name eth0.1 type vlan id 1 115 116 # The master interface needs to be brought up before the slave ports. 117 ip link set eth0 up 118 ip link set eth0.1 up 119 120 # bring up the slave interfaces 121 ip link set wan up 122 ip link set lan1 up 123 ip link set lan2 up 124 125 # create bridge 126 ip link add name br0 type bridge 127 128 # activate VLAN filtering 129 ip link set dev br0 type bridge vlan_filtering 1 130 131 # add ports to bridge 132 ip link set dev wan master br0 133 ip link set dev lan1 master br0 134 ip link set dev lan2 master br0 135 ip link set eth0.1 master br0 136 137 # configure the bridge 138 ip addr add 192.0.2.129/25 dev br0 139 140 # bring up the bridge 141 ip link set dev br0 up 142 143gateway 144~~~~~~~ 145 146.. code-block:: sh 147 148 # tag traffic on CPU port 149 ip link add link eth0 name eth0.1 type vlan id 1 150 ip link add link eth0 name eth0.2 type vlan id 2 151 152 # The master interface needs to be brought up before the slave ports. 153 ip link set eth0 up 154 ip link set eth0.1 up 155 ip link set eth0.2 up 156 157 # bring up the slave interfaces 158 ip link set wan up 159 ip link set lan1 up 160 ip link set lan2 up 161 162 # create bridge 163 ip link add name br0 type bridge 164 165 # activate VLAN filtering 166 ip link set dev br0 type bridge vlan_filtering 1 167 168 # add ports to bridges 169 ip link set dev wan master br0 170 ip link set eth0.1 master br0 171 ip link set dev lan1 master br0 172 ip link set dev lan2 master br0 173 174 # tag traffic on ports 175 bridge vlan add dev wan vid 2 pvid untagged 176 bridge vlan del dev wan vid 1 177 178 # configure the VLANs 179 ip addr add 192.0.2.1/30 dev eth0.2 180 ip addr add 192.0.2.129/25 dev br0 181 182 # bring up the bridge devices 183 ip link set br0 up