axc001.dtsi (3053B)
1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com) 4 */ 5 6/* 7 * Device tree for AXC001 770D/EM6/AS221 CPU card 8 * Note that this file only supports the 770D CPU 9 */ 10 11/include/ "skeleton.dtsi" 12 13/ { 14 compatible = "snps,arc"; 15 #address-cells = <2>; 16 #size-cells = <2>; 17 18 cpu_card { 19 compatible = "simple-bus"; 20 #address-cells = <1>; 21 #size-cells = <1>; 22 23 ranges = <0x00000000 0x0 0xf0000000 0x10000000>; 24 25 core_clk: core_clk { 26 #clock-cells = <0>; 27 compatible = "fixed-clock"; 28 clock-frequency = <750000000>; 29 }; 30 31 input_clk: input-clk { 32 #clock-cells = <0>; 33 compatible = "fixed-clock"; 34 clock-frequency = <33333333>; 35 }; 36 37 core_intc: arc700-intc@cpu { 38 compatible = "snps,arc700-intc"; 39 interrupt-controller; 40 #interrupt-cells = <1>; 41 }; 42 43 /* 44 * this GPIO block ORs all interrupts on CPU card (creg,..) 45 * to uplink only 1 IRQ to ARC core intc 46 */ 47 dw-apb-gpio@2000 { 48 compatible = "snps,dw-apb-gpio"; 49 reg = < 0x2000 0x80 >; 50 #address-cells = <1>; 51 #size-cells = <0>; 52 53 ictl_intc: gpio-controller@0 { 54 compatible = "snps,dw-apb-gpio-port"; 55 gpio-controller; 56 #gpio-cells = <2>; 57 snps,nr-gpios = <30>; 58 reg = <0>; 59 interrupt-controller; 60 #interrupt-cells = <2>; 61 interrupt-parent = <&core_intc>; 62 interrupts = <15>; 63 }; 64 }; 65 66 debug_uart: dw-apb-uart@5000 { 67 compatible = "snps,dw-apb-uart"; 68 reg = <0x5000 0x100>; 69 clock-frequency = <33333000>; 70 interrupt-parent = <&ictl_intc>; 71 interrupts = <19 4>; 72 baud = <115200>; 73 reg-shift = <2>; 74 reg-io-width = <4>; 75 }; 76 77 arcpct0: pct { 78 compatible = "snps,arc700-pct"; 79 }; 80 }; 81 82 /* 83 * This INTC is actually connected to DW APB GPIO 84 * which acts as a wire between MB INTC and CPU INTC. 85 * GPIO INTC is configured in platform init code 86 * and here we mimic direct connection from MB INTC to 87 * CPU INTC, thus we set "interrupts = <7>" instead of 88 * "interrupts = <12>" 89 * 90 * This intc actually resides on MB, but we move it here to 91 * avoid duplicating the MB dtsi file given that IRQ from 92 * this intc to cpu intc are different for axs101 and axs103 93 */ 94 mb_intc: interrupt-controller@e0012000 { 95 #interrupt-cells = <1>; 96 compatible = "snps,dw-apb-ictl"; 97 reg = < 0x0 0xe0012000 0x0 0x200 >; 98 interrupt-controller; 99 interrupt-parent = <&core_intc>; 100 interrupts = < 7 >; 101 }; 102 103 memory { 104 device_type = "memory"; 105 /* CONFIG_LINUX_RAM_BASE needs to match low mem start */ 106 reg = <0x0 0x80000000 0x0 0x1b000000>; /* (512 - 32) MiB */ 107 }; 108 109 reserved-memory { 110 #address-cells = <2>; 111 #size-cells = <2>; 112 ranges; 113 /* 114 * We just move frame buffer area to the very end of 115 * available DDR. And even though in case of ARC770 there's 116 * no strict requirement for a frame-buffer to be in any 117 * particular location it allows us to use the same 118 * base board's DT node for ARC PGU as for ARc HS38. 119 */ 120 frame_buffer: frame_buffer@9e000000 { 121 compatible = "shared-dma-pool"; 122 reg = <0x0 0x9e000000 0x0 0x2000000>; 123 no-map; 124 }; 125 }; 126};