animeo_ip.dts (3577B)
1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * animeo_ip.dts - Device Tree file for Somfy Animeo IP Boards 4 * 5 * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> 6 */ 7 8/dts-v1/; 9#include "at91sam9260.dtsi" 10 11/ { 12 model = "Somfy Animeo IP"; 13 compatible = "somfy,animeo-ip", "atmel,at91sam9260", "atmel,at91sam9"; 14 15 aliases { 16 serial0 = &usart1; 17 serial1 = &usart2; 18 serial2 = &usart0; 19 serial3 = &dbgu; 20 serial4 = &usart3; 21 serial5 = &uart0; 22 serial6 = &uart1; 23 }; 24 25 chosen { 26 stdout-path = &usart2; 27 }; 28 29 memory@20000000 { 30 reg = <0x20000000 0x4000000>; 31 }; 32 33 clocks { 34 slow_xtal { 35 clock-frequency = <32768>; 36 }; 37 38 main_xtal { 39 clock-frequency = <18432000>; 40 }; 41 }; 42 43 ahb { 44 apb { 45 tcb0: timer@fffa0000 { 46 timer@0 { 47 compatible = "atmel,tcb-timer"; 48 reg = <0>, <1>; 49 }; 50 51 timer@2 { 52 compatible = "atmel,tcb-timer"; 53 reg = <2>; 54 }; 55 }; 56 57 usart0: serial@fffb0000 { 58 pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts>; 59 linux,rs485-enabled-at-boot-time; 60 status = "okay"; 61 }; 62 63 usart1: serial@fffb4000 { 64 pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts>; 65 linux,rs485-enabled-at-boot-time; 66 status = "okay"; 67 }; 68 69 usart2: serial@fffb8000 { 70 pinctrl-0 = <&pinctrl_usart2>; 71 status = "okay"; 72 }; 73 74 macb0: ethernet@fffc4000 { 75 pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii>; 76 phy-mode = "mii"; 77 status = "okay"; 78 }; 79 80 mmc0: mmc@fffa8000 { 81 pinctrl-0 = <&pinctrl_mmc0_clk 82 &pinctrl_mmc0_slot1_cmd_dat0 83 &pinctrl_mmc0_slot1_dat1_3>; 84 pinctrl-names = "default"; 85 status = "okay"; 86 87 slot@1 { 88 reg = <1>; 89 bus-width = <4>; 90 }; 91 }; 92 93 watchdog@fffffd40 { 94 status = "okay"; 95 }; 96 }; 97 98 ebi: ebi@10000000 { 99 status = "okay"; 100 101 nand_controller: nand-controller { 102 status = "okay"; 103 pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>; 104 pinctrl-names = "default"; 105 106 nand@3 { 107 reg = <0x3 0x0 0x800000>; 108 rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>; 109 cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>; 110 nand-bus-width = <8>; 111 nand-ecc-mode = "soft"; 112 nand-on-flash-bbt; 113 label = "atmel_nand"; 114 115 partitions { 116 compatible = "fixed-partitions"; 117 #address-cells = <1>; 118 #size-cells = <1>; 119 120 barebox@0 { 121 label = "barebox"; 122 reg = <0x0 0x58000>; 123 }; 124 125 u_boot_env@58000 { 126 label = "u_boot_env"; 127 reg = <0x58000 0x8000>; 128 }; 129 130 ubi@60000 { 131 label = "ubi"; 132 reg = <0x60000 0x1FA0000>; 133 }; 134 }; 135 }; 136 }; 137 }; 138 139 usb0: ohci@500000 { 140 num-ports = <2>; 141 atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>; 142 status = "okay"; 143 }; 144 }; 145 146 leds { 147 compatible = "gpio-leds"; 148 149 power_green { 150 label = "power_green"; 151 gpios = <&pioC 17 GPIO_ACTIVE_HIGH>; 152 linux,default-trigger = "heartbeat"; 153 }; 154 155 power_red { 156 label = "power_red"; 157 gpios = <&pioA 2 GPIO_ACTIVE_HIGH>; 158 }; 159 160 tx_green { 161 label = "tx_green"; 162 gpios = <&pioC 19 GPIO_ACTIVE_HIGH>; 163 }; 164 165 tx_red { 166 label = "tx_red"; 167 gpios = <&pioC 18 GPIO_ACTIVE_HIGH>; 168 }; 169 }; 170 171 gpio_keys { 172 compatible = "gpio-keys"; 173 #address-cells = <1>; 174 #size-cells = <0>; 175 176 keyswitch_in { 177 label = "keyswitch_in"; 178 gpios = <&pioB 1 GPIO_ACTIVE_HIGH>; 179 linux,code = <28>; 180 wakeup-source; 181 }; 182 183 error_in { 184 label = "error_in"; 185 gpios = <&pioB 2 GPIO_ACTIVE_HIGH>; 186 linux,code = <29>; 187 wakeup-source; 188 }; 189 190 btn { 191 label = "btn"; 192 gpios = <&pioC 23 GPIO_ACTIVE_HIGH>; 193 linux,code = <31>; 194 wakeup-source; 195 }; 196 }; 197};