imx6qdl-dhcom-som.dtsi (20013B)
1// SPDX-License-Identifier: GPL-2.0+ 2/* 3 * Copyright (C) 2015-2021 DH electronics GmbH 4 * Copyright (C) 2018 Marek Vasut <marex@denx.de> 5 */ 6 7#include <dt-bindings/pwm/pwm.h> 8#include <dt-bindings/gpio/gpio.h> 9#include <dt-bindings/clock/imx6qdl-clock.h> 10#include <dt-bindings/input/input.h> 11 12/ { 13 aliases { 14 i2c0 = &i2c2; 15 i2c1 = &i2c1; 16 i2c2 = &i2c3; 17 mmc0 = &usdhc2; 18 mmc1 = &usdhc3; 19 mmc2 = &usdhc4; 20 mmc3 = &usdhc1; 21 rtc0 = &rtc_i2c; 22 rtc1 = &snvs_rtc; 23 serial0 = &uart1; 24 serial1 = &uart5; 25 serial2 = &uart4; 26 serial3 = &uart2; 27 serial4 = &uart3; 28 }; 29 30 memory@10000000 { /* Appropriate memory size will be filled by U-Boot */ 31 device_type = "memory"; 32 reg = <0x10000000 0x20000000>; 33 }; 34 35 reg_3p3v: regulator-3P3V { 36 compatible = "regulator-fixed"; 37 regulator-always-on; 38 regulator-min-microvolt = <3300000>; 39 regulator-max-microvolt = <3300000>; 40 regulator-name = "3P3V"; 41 }; 42 43 reg_eth_vio: regulator-eth-vio { 44 compatible = "regulator-fixed"; 45 gpio = <&gpio1 7 0>; 46 pinctrl-0 = <&pinctrl_enet_vio>; 47 pinctrl-names = "default"; 48 regulator-always-on; 49 regulator-boot-on; 50 regulator-min-microvolt = <3300000>; 51 regulator-max-microvolt = <3300000>; 52 regulator-name = "eth_vio"; 53 vin-supply = <&sw2_reg>; 54 }; 55 56 /* OE pin of the latch is low active */ 57 reg_latch_oe_on: regulator-latch-oe-on { 58 compatible = "regulator-fixed"; 59 gpio = <&gpio3 22 0>; 60 regulator-always-on; 61 regulator-name = "latch_oe_on"; 62 }; 63 64 reg_usb_h1_vbus: regulator-usb-h1-vbus { 65 compatible = "regulator-fixed"; 66 enable-active-high; 67 gpio = <&gpio3 31 0>; 68 regulator-min-microvolt = <5000000>; 69 regulator-max-microvolt = <5000000>; 70 regulator-name = "usb_h1_vbus"; 71 }; 72 73 reg_usb_otg_vbus: regulator-usb-otg-vbus { 74 compatible = "regulator-fixed"; 75 regulator-min-microvolt = <5000000>; 76 regulator-max-microvolt = <5000000>; 77 regulator-name = "usb_otg_vbus"; 78 }; 79}; 80 81&can1 { 82 pinctrl-0 = <&pinctrl_flexcan1>; 83 pinctrl-names = "default"; 84 status = "okay"; 85}; 86 87/* 88 * Special SoM hardware required which uses the pins from micro SD card. The 89 * pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2 90 * Tx and Rx are routed to the DHCOM UART1 rts/cts pins. So to enable can2 on 91 * the board device tree file, the micro SD card must be disabled and the uart1 92 * rts/cts must be disabled or output on other DHCOM pins. 93 */ 94&can2 { 95 pinctrl-0 = <&pinctrl_flexcan2>; 96 pinctrl-names = "default"; 97 status = "disabled"; 98}; 99 100&ecspi1 { 101 cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio4 11 GPIO_ACTIVE_LOW>; 102 pinctrl-0 = <&pinctrl_ecspi1>; 103 pinctrl-names = "default"; 104 status = "okay"; 105 106 flash@0 { /* S25FL116K */ 107 #address-cells = <1>; 108 #size-cells = <1>; 109 compatible = "jedec,spi-nor"; 110 m25p,fast-read; 111 reg = <0>; 112 spi-max-frequency = <50000000>; 113 }; 114}; 115 116&ecspi2 { 117 cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>; 118 pinctrl-0 = <&pinctrl_ecspi2>; 119 pinctrl-names = "default"; 120 status = "disabled"; 121}; 122 123&fec { 124 phy-mode = "rmii"; 125 phy-handle = <ðphy0>; 126 pinctrl-0 = <&pinctrl_enet_100M>; 127 pinctrl-names = "default"; 128 status = "okay"; 129 130 mdio { 131 #address-cells = <1>; 132 #size-cells = <0>; 133 134 ethphy0: ethernet-phy@0 { /* SMSC LAN8710Ai */ 135 compatible = "ethernet-phy-id0007.c0f0", 136 "ethernet-phy-ieee802.3-c22"; 137 interrupt-parent = <&gpio4>; 138 interrupts = <15 IRQ_TYPE_LEVEL_LOW>; 139 pinctrl-0 = <&pinctrl_ethphy0>; 140 pinctrl-names = "default"; 141 reg = <0>; 142 reset-assert-us = <500>; 143 reset-deassert-us = <500>; 144 reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; 145 smsc,disable-energy-detect; /* Make plugin detection reliable */ 146 }; 147 }; 148}; 149 150&gpio1 { 151 gpio-line-names = 152 "", "", "DHCOM-A", "", "DHCOM-B", "DHCOM-C", "", "", 153 "", "", "", "", "", "", "", "", 154 "DHCOM-R", "DHCOM-S", "DHCOM-Q", "DHCOM-T", "DHCOM-U", "", "", "", 155 "", "", "", "", "", "", "", ""; 156}; 157 158&gpio2 { 159 gpio-line-names = 160 "", "", "", "", "", "", "", "", 161 "", "", "", "", "", "", "", "", 162 "SOM-HW2", "", "", "SOM-HW0", "", "SOM-MEM1", "SOM-MEM0", "", 163 "", "", "", "", "", "", "", ""; 164}; 165 166&gpio3 { 167 gpio-line-names = 168 "", "", "", "", "", "", "", "", 169 "", "", "", "", "", "", "", "", 170 "", "", "", "", "", "", "", "", 171 "", "", "", "DHCOM-G", "", "", "", ""; 172}; 173 174&gpio4 { 175 gpio-line-names = 176 "", "", "", "", "", "DHCOM-E", "DHCOM-INT", "DHCOM-H", 177 "DHCOM-I", "DHCOM-L", "", "", "", "", "", "", 178 "", "", "", "", "DHCOM-F", "", "", "", 179 "", "", "", "", "", "", "", ""; 180}; 181 182&gpio5 { 183 gpio-line-names = 184 "", "", "", "", "", "", "", "", 185 "", "", "", "", "", "", "", "", 186 "", "", "DHCOM-V", "DHCOM-W", "", "DHCOM-O", "", "", 187 "", "", "", "", "", "", "", ""; 188}; 189 190&gpio6 { 191 gpio-line-names = 192 "", "", "", "DHCOM-D", "", "", "SOM-HW1", "", 193 "", "", "", "", "", "", "DHCOM-J", "DHCOM-K", 194 "", "", "", "", "", "", "", "", 195 "", "", "", "", "", "", "", ""; 196}; 197 198&gpio7 { 199 gpio-line-names = 200 "DHCOM-M", "DHCOM-N", "", "", "", "", "", "", 201 "", "", "", "", "", "DHCOM-P", "", "", 202 "", "", "", "", "", "", "", "", 203 "", "", "", "", "", "", "", ""; 204}; 205 206&i2c1 { 207 /* 208 * Info: According to erratum ERR007805 clock frequency limit is 375000. 209 * The erratum for i.MX6S/DL is here [1] and for i.MX6Q/D is here [2]. 210 * [1] https://www.nxp.com/docs/en/errata/IMX6SDLCE.pdf 211 * [2] https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf 212 */ 213 clock-frequency = <100000>; 214 pinctrl-0 = <&pinctrl_i2c1>; 215 pinctrl-1 = <&pinctrl_i2c1_gpio>; 216 pinctrl-names = "default", "gpio"; 217 scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 218 sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 219 status = "okay"; 220}; 221 222&i2c2 { 223 /* Info: Clock frequency limit is 375000 (for details see i2c1) */ 224 clock-frequency = <100000>; 225 pinctrl-0 = <&pinctrl_i2c2>; 226 pinctrl-1 = <&pinctrl_i2c2_gpio>; 227 pinctrl-names = "default", "gpio"; 228 scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 229 sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 230 status = "okay"; 231}; 232 233&i2c3 { 234 /* Info: Clock frequency limit is 375000 (for details see i2c1) */ 235 clock-frequency = <100000>; 236 pinctrl-0 = <&pinctrl_i2c3>; 237 pinctrl-1 = <&pinctrl_i2c3_gpio>; 238 pinctrl-names = "default", "gpio"; 239 scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 240 sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 241 status = "okay"; 242 243 ltc3676: pmic@3c { 244 compatible = "lltc,ltc3676"; 245 interrupt-parent = <&gpio5>; 246 interrupts = <2 IRQ_TYPE_EDGE_FALLING>; 247 pinctrl-0 = <&pinctrl_pmic>; 248 pinctrl-names = "default"; 249 reg = <0x3c>; 250 251 regulators { 252 sw1_reg: sw1 { 253 lltc,fb-voltage-divider = <100000 110000>; 254 regulator-always-on; 255 regulator-boot-on; 256 regulator-max-microvolt = <1527272>; 257 regulator-min-microvolt = <787500>; 258 regulator-ramp-delay = <7000>; 259 regulator-suspend-mem-microvolt = <1040000>; 260 }; 261 262 sw2_reg: sw2 { 263 lltc,fb-voltage-divider = <100000 28000>; 264 regulator-always-on; 265 regulator-boot-on; 266 regulator-max-microvolt = <3657142>; 267 regulator-min-microvolt = <1885714>; 268 regulator-ramp-delay = <7000>; 269 }; 270 271 sw3_reg: sw3 { 272 lltc,fb-voltage-divider = <100000 110000>; 273 regulator-always-on; 274 regulator-boot-on; 275 regulator-max-microvolt = <1527272>; 276 regulator-min-microvolt = <787500>; 277 regulator-ramp-delay = <7000>; 278 regulator-suspend-mem-microvolt = <980000>; 279 }; 280 281 sw4_reg: sw4 { 282 lltc,fb-voltage-divider = <100000 93100>; 283 regulator-always-on; 284 regulator-boot-on; 285 regulator-max-microvolt = <1659291>; 286 regulator-min-microvolt = <855571>; 287 regulator-ramp-delay = <7000>; 288 }; 289 290 ldo1_reg: ldo1 { 291 lltc,fb-voltage-divider = <102000 29400>; 292 regulator-always-on; 293 regulator-boot-on; 294 regulator-max-microvolt = <3240306>; 295 regulator-min-microvolt = <3240306>; 296 }; 297 298 ldo2_reg: ldo2 { 299 lltc,fb-voltage-divider = <100000 41200>; 300 regulator-always-on; 301 regulator-boot-on; 302 regulator-max-microvolt = <2484708>; 303 regulator-min-microvolt = <2484708>; 304 }; 305 }; 306 }; 307 308 touchscreen@49 { /* TSC2004 */ 309 compatible = "ti,tsc2004"; 310 interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>; 311 pinctrl-0 = <&pinctrl_tsc2004>; 312 pinctrl-names = "default"; 313 reg = <0x49>; 314 vio-supply = <®_3p3v>; 315 status = "disabled"; 316 }; 317 318 eeprom@50 { 319 compatible = "atmel,24c02"; 320 pagesize = <16>; 321 reg = <0x50>; 322 }; 323 324 rtc_i2c: rtc@56 { 325 compatible = "microcrystal,rv3029"; 326 interrupt-parent = <&gpio7>; 327 interrupts = <12 IRQ_TYPE_EDGE_FALLING>; 328 pinctrl-0 = <&pinctrl_rtc>; 329 pinctrl-names = "default"; 330 reg = <0x56>; 331 }; 332}; 333 334&pcie { 335 pinctrl-0 = <&pinctrl_pcie>; 336 pinctrl-names = "default"; 337}; 338 339&pwm1 { 340 pinctrl-0 = <&pinctrl_pwm1>; 341 pinctrl-names = "default"; 342}; 343 344®_arm { 345 vin-supply = <&sw3_reg>; 346}; 347 348®_pu { 349 vin-supply = <&sw1_reg>; 350}; 351 352®_soc { 353 vin-supply = <&sw1_reg>; 354}; 355 356®_vdd1p1 { 357 vin-supply = <&sw2_reg>; 358}; 359 360®_vdd2p5 { 361 vin-supply = <&sw2_reg>; 362}; 363 364&uart1 { /* DHCOM UART1 */ 365 dcd-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; 366 dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>; 367 dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>; 368 rng-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>; 369 pinctrl-0 = <&pinctrl_uart1>; 370 pinctrl-names = "default"; 371 uart-has-rtscts; 372 status = "okay"; 373}; 374 375&uart4 { /* DHCOM UART3 */ 376 pinctrl-0 = <&pinctrl_uart4>; 377 pinctrl-names = "default"; 378 status = "okay"; 379}; 380 381&uart5 { /* DHCOM UART2 */ 382 pinctrl-0 = <&pinctrl_uart5>; 383 pinctrl-names = "default"; 384 uart-has-rtscts; 385 status = "okay"; 386}; 387 388&usbh1 { 389 dr_mode = "host"; 390 pinctrl-0 = <&pinctrl_usbh1>; 391 pinctrl-names = "default"; 392 vbus-supply = <®_usb_h1_vbus>; 393 status = "okay"; 394}; 395 396&usbotg { 397 disable-over-current; 398 dr_mode = "otg"; 399 pinctrl-0 = <&pinctrl_usbotg>; 400 pinctrl-names = "default"; 401 vbus-supply = <®_usb_otg_vbus>; 402 status = "okay"; 403}; 404 405&usdhc2 { /* External SD card via DHCOM */ 406 cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>; 407 keep-power-in-suspend; 408 pinctrl-0 = <&pinctrl_usdhc2>; 409 pinctrl-names = "default"; 410 status = "disabled"; 411}; 412 413&usdhc3 { /* Micro SD card on module */ 414 cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>; 415 fsl,wp-controller; 416 keep-power-in-suspend; 417 pinctrl-0 = <&pinctrl_usdhc3>; 418 pinctrl-names = "default"; 419 status = "okay"; 420}; 421 422&usdhc4 { /* eMMC on module */ 423 bus-width = <8>; 424 keep-power-in-suspend; 425 no-1-8-v; 426 non-removable; 427 pinctrl-0 = <&pinctrl_usdhc4>; 428 pinctrl-names = "default"; 429 status = "okay"; 430}; 431 432&weim { 433 #address-cells = <2>; 434 #size-cells = <1>; 435 fsl,weim-cs-gpr = <&gpr>; 436 pinctrl-0 = <&pinctrl_weim &pinctrl_weim_cs0 &pinctrl_weim_cs1>; 437 pinctrl-names = "default"; 438 /* It is necessary to setup 2x 64MB otherwise setting gpr fails */ 439 ranges = <0 0 0x08000000 0x04000000>, /* CS0 */ 440 <1 0 0x0c000000 0x04000000>; /* CS1 */ 441 status = "disabled"; 442}; 443 444&iomuxc { 445 pinctrl-0 = < 446 &pinctrl_hog_base 447 &pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c 448 &pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f 449 &pinctrl_dhcom_g &pinctrl_dhcom_h &pinctrl_dhcom_i 450 &pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l 451 &pinctrl_dhcom_m &pinctrl_dhcom_n &pinctrl_dhcom_o 452 &pinctrl_dhcom_p &pinctrl_dhcom_q &pinctrl_dhcom_r 453 &pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u 454 &pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int 455 >; 456 pinctrl-names = "default"; 457 458 pinctrl_hog_base: hog-base-grp { 459 fsl,pins = < 460 /* GPIOs for memory coding */ 461 MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x120b0 462 MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x120b0 463 /* GPIOs for hardware coding */ 464 MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x120b0 465 MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x120b0 466 MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x120b0 467 >; 468 }; 469 470 /* DHCOM GPIOs */ 471 pinctrl_dhcom_a: dhcom-a-grp { 472 fsl,pins = <MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x400120b0>; 473 }; 474 475 pinctrl_dhcom_b: dhcom-b-grp { 476 fsl,pins = <MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x400120b0>; 477 }; 478 479 pinctrl_dhcom_c: dhcom-c-grp { 480 fsl,pins = <MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x400120b0>; 481 }; 482 483 pinctrl_dhcom_d: dhcom-d-grp { 484 fsl,pins = <MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x400120b0>; 485 }; 486 487 pinctrl_dhcom_e: dhcom-e-grp { 488 fsl,pins = <MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x400120b0>; 489 }; 490 491 pinctrl_dhcom_f: dhcom-f-grp { 492 fsl,pins = <MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x400120b0>; 493 }; 494 495 pinctrl_dhcom_g: dhcom-g-grp { 496 fsl,pins = <MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x400120b0>; 497 }; 498 499 pinctrl_dhcom_h: dhcom-h-grp { 500 fsl,pins = <MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x400120b0>; 501 }; 502 503 pinctrl_dhcom_i: dhcom-i-grp { 504 fsl,pins = <MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x400120b0>; 505 }; 506 507 pinctrl_dhcom_j: dhcom-j-grp { 508 fsl,pins = <MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x400120b0>; 509 }; 510 511 pinctrl_dhcom_k: dhcom-k-grp { 512 fsl,pins = <MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x400120b0>; 513 }; 514 515 pinctrl_dhcom_l: dhcom-l-grp { 516 fsl,pins = <MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x400120b0>; 517 }; 518 519 pinctrl_dhcom_m: dhcom-m-grp { 520 fsl,pins = <MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x400120b0>; 521 }; 522 523 pinctrl_dhcom_n: dhcom-n-grp { 524 fsl,pins = <MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x400120b0>; 525 }; 526 527 pinctrl_dhcom_o: dhcom-o-grp { 528 fsl,pins = <MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x400120b0>; 529 }; 530 531 pinctrl_dhcom_p: dhcom-p-grp { 532 fsl,pins = <MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x400120b0>; 533 }; 534 535 pinctrl_dhcom_q: dhcom-q-grp { 536 fsl,pins = <MX6QDL_PAD_SD1_CMD__GPIO1_IO18 0x400120b0>; 537 }; 538 539 pinctrl_dhcom_r: dhcom-r-grp { 540 fsl,pins = <MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x400120b0>; 541 }; 542 543 pinctrl_dhcom_s: dhcom-s-grp { 544 fsl,pins = <MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x400120b0>; 545 }; 546 547 pinctrl_dhcom_t: dhcom-t-grp { 548 fsl,pins = <MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x400120b0>; 549 }; 550 551 pinctrl_dhcom_u: dhcom-u-grp { 552 fsl,pins = <MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x400120b0>; 553 }; 554 555 pinctrl_dhcom_v: dhcom-v-grp { 556 fsl,pins = <MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x400120b0>; 557 }; 558 559 pinctrl_dhcom_w: dhcom-w-grp { 560 fsl,pins = <MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x400120b0>; 561 }; 562 563 pinctrl_dhcom_int: dhcom-int-grp { 564 fsl,pins = <MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x400120b0>; 565 }; 566 567 pinctrl_ecspi1: ecspi1-grp { 568 fsl,pins = < 569 MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 570 MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 571 MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 572 MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 573 MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0 574 >; 575 }; 576 577 pinctrl_ecspi2: ecspi2-grp { 578 fsl,pins = < 579 MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK 0x100b1 580 MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x100b1 581 MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x100b1 582 MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x1b0b0 583 >; 584 }; 585 586 pinctrl_enet_100M: enet-100M-grp { 587 fsl,pins = < 588 MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 589 MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 590 MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 591 MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 592 MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 593 MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 594 MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 595 MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 596 MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 597 MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 598 >; 599 }; 600 601 pinctrl_enet_vio: enet-vio-grp { 602 fsl,pins = < 603 MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x120b0 604 >; 605 }; 606 607 pinctrl_ethphy0: ethphy0-grp { 608 fsl,pins = < 609 MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0xb0 /* Reset */ 610 MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0xb1 /* Int */ 611 >; 612 }; 613 614 pinctrl_flexcan1: flexcan1-grp { 615 fsl,pins = < 616 MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0 617 MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0 618 >; 619 }; 620 621 pinctrl_flexcan2: flexcan2-grp { 622 fsl,pins = < 623 MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x1b0b0 624 MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x1b0b0 625 >; 626 }; 627 628 pinctrl_i2c1: i2c1-grp { 629 fsl,pins = < 630 MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 631 MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 632 >; 633 }; 634 635 pinctrl_i2c1_gpio: i2c1-gpio-grp { 636 fsl,pins = < 637 MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x4001b8b1 638 MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x4001b8b1 639 >; 640 }; 641 642 pinctrl_i2c2: i2c2-grp { 643 fsl,pins = < 644 MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 645 MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 646 >; 647 }; 648 649 pinctrl_i2c2_gpio: i2c2-gpio-grp { 650 fsl,pins = < 651 MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b8b1 652 MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b8b1 653 >; 654 }; 655 656 pinctrl_i2c3: i2c3-grp { 657 fsl,pins = < 658 MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 659 MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 660 >; 661 }; 662 663 pinctrl_i2c3_gpio: i2c3-gpio-grp { 664 fsl,pins = < 665 MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x4001b8b1 666 MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b8b1 667 >; 668 }; 669 670 pinctrl_pcie: pcie-grp { 671 fsl,pins = < 672 MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b1 /* Wake */ 673 >; 674 }; 675 676 pinctrl_pmic: pmic-grp { 677 fsl,pins = < 678 MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0 679 >; 680 }; 681 682 pinctrl_pwm1: pwm1-grp { 683 fsl,pins = < 684 MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 685 >; 686 }; 687 688 pinctrl_rtc: rtc-grp { 689 fsl,pins = < 690 MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x120b0 691 >; 692 }; 693 694 pinctrl_tsc2004: tsc2004-grp { 695 fsl,pins = < 696 MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x120b0 697 >; 698 }; 699 700 pinctrl_uart1: uart1-grp { 701 fsl,pins = < 702 MX6QDL_PAD_EIM_D19__UART1_CTS_B 0x4001b0b1 703 MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x1b0b1 704 MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x4001b0b1 705 MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x4001b0b1 706 MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x4001b0b1 707 MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x4001b0b1 708 MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 709 MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 710 >; 711 }; 712 713 pinctrl_uart4: uart4-grp { 714 fsl,pins = < 715 MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1 716 MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1 717 >; 718 }; 719 720 pinctrl_uart5: uart5-grp { 721 fsl,pins = < 722 MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1 723 MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1 724 MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B 0x1b0b1 725 MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x4001b0b1 726 >; 727 }; 728 729 pinctrl_usbh1: usbh1-grp { 730 fsl,pins = < 731 MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x120b0 732 MX6QDL_PAD_EIM_D30__USB_H1_OC 0x1b0b1 733 >; 734 }; 735 736 pinctrl_usbotg: usbotg-grp { 737 fsl,pins = < 738 MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 739 >; 740 }; 741 742 pinctrl_usdhc2: usdhc2-grp { 743 fsl,pins = < 744 MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x120b0 745 MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 746 MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 747 MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 748 MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 749 MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 750 MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 751 >; 752 }; 753 754 pinctrl_usdhc3: usdhc3-grp { 755 fsl,pins = < 756 MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 757 MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 758 MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 759 MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 760 MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 761 MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 762 MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x120b0 763 >; 764 }; 765 766 pinctrl_usdhc4: usdhc4-grp { 767 fsl,pins = < 768 MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 769 MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 770 MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 771 MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 772 MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 773 MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 774 MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 775 MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 776 MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 777 MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 778 >; 779 }; 780 781 pinctrl_weim: weim-grp { 782 fsl,pins = < 783 MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0a6 784 MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0a6 785 MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0a6 786 MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0a6 787 MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0a6 788 MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0a6 789 MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0a6 790 MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0a6 791 MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0a6 792 MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0a6 793 MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0a6 794 MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0a6 795 MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0a6 796 MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0a6 797 MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0a6 798 MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0a6 799 MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x130b0 800 MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb060 /* LE */ 801 MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0a6 802 MX6QDL_PAD_EIM_RW__EIM_RW 0xb0a6 /* WE */ 803 >; 804 }; 805 806 pinctrl_weim_cs0: weim-cs0-grp { 807 fsl,pins = < 808 MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1 809 >; 810 }; 811 812 pinctrl_weim_cs1: weim-cs1-grp { 813 fsl,pins = < 814 MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1 815 >; 816 }; 817};