intel-ixp42x-gateworks-gw2348.dts (4810B)
1// SPDX-License-Identifier: ISC 2/* 3 * Device Tree file for the Gateworks Avila GW2348 board. 4 * This machine is based on IXP425. 5 */ 6 7/dts-v1/; 8 9#include "intel-ixp42x.dtsi" 10#include <dt-bindings/input/input.h> 11 12/ { 13 model = "Gateworks Avila GW2348"; 14 compatible = "gateworks,gw2348", "intel,ixp42x"; 15 #address-cells = <1>; 16 #size-cells = <1>; 17 18 memory@0 { 19 device_type = "memory"; 20 reg = <0x00000000 0x4000000>; 21 }; 22 23 chosen { 24 bootargs = "console=ttyS0,115200n8"; 25 stdout-path = "uart0:115200n8"; 26 }; 27 28 aliases { 29 serial0 = &uart0; 30 }; 31 32 leds { 33 compatible = "gpio-leds"; 34 led-user { 35 label = "gw2348:green:user"; 36 gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; 37 default-state = "on"; 38 linux,default-trigger = "heartbeat"; 39 }; 40 }; 41 42 i2c { 43 compatible = "i2c-gpio"; 44 sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; 45 scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; 46 #address-cells = <1>; 47 #size-cells = <0>; 48 49 hwmon@28 { 50 compatible = "adi,ad7418"; 51 reg = <0x28>; 52 }; 53 rtc: ds1672@68 { 54 compatible = "dallas,ds1672"; 55 reg = <0x68>; 56 }; 57 eeprom@51 { 58 compatible = "atmel,24c08"; 59 reg = <0x51>; 60 pagesize = <16>; 61 size = <1024>; 62 read-only; 63 }; 64 }; 65 66 soc { 67 bus@c4000000 { 68 flash@0,0 { 69 compatible = "intel,ixp4xx-flash", "cfi-flash"; 70 bank-width = <2>; 71 /* Enable writes on the expansion bus */ 72 intel,ixp4xx-eb-write-enable = <1>; 73 /* 16 MB of Flash mapped in at CS0 */ 74 reg = <0 0x00000000 0x1000000>; 75 76 partitions { 77 compatible = "redboot-fis"; 78 /* Eraseblock at 0x0fe0000 */ 79 fis-index-block = <0x7f>; 80 }; 81 }; 82 ide@1,0 { 83 compatible = "intel,ixp4xx-compact-flash"; 84 /* 85 * Set up expansion bus config to a really slow timing. 86 * The CF driver will dynamically reconfigure these timings 87 * depending on selected PIO mode (0-4). 88 */ 89 intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase 90 intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase 91 intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase 92 intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase 93 intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase 94 intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type 95 intel,ixp4xx-eb-byte-access-on-halfword = <1>; 96 intel,ixp4xx-eb-mux-address-and-data = <0>; 97 intel,ixp4xx-eb-ahb-split-transfers = <0>; 98 intel,ixp4xx-eb-write-enable = <1>; 99 intel,ixp4xx-eb-byte-access = <1>; 100 /* First register set is CMD second is CTL (notice it uses CS2) */ 101 reg = <1 0x00000000 0x1000000>, <2 0x00000000 0x1000000>; 102 interrupt-parent = <&gpio0>; 103 interrupts = <12 IRQ_TYPE_EDGE_RISING>; 104 }; 105 /* 106 * FIXME: Latch LEDs or extra UARTs at CS4 107 */ 108 }; 109 110 pci@c0000000 { 111 status = "ok"; 112 113 /* 114 * Taken from Avila PCI boardfile. 115 * 116 * We have up to 4 slots (IDSEL) with 4 swizzled IRQs. 117 */ 118 #interrupt-cells = <1>; 119 interrupt-map-mask = <0xf800 0 0 7>; 120 interrupt-map = 121 /* IDSEL 1 */ 122 <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ 123 <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ 124 <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ 125 <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ 126 /* IDSEL 2 */ 127 <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ 128 <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ 129 <0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */ 130 <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */ 131 /* IDSEL 3 */ 132 <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ 133 <0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ 134 <0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */ 135 <0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */ 136 /* IDSEL 4 */ 137 <0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */ 138 <0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */ 139 <0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */ 140 <0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */ 141 }; 142 143 /* EthB */ 144 ethernet@c8009000 { 145 status = "ok"; 146 queue-rx = <&qmgr 3>; 147 queue-txready = <&qmgr 20>; 148 phy-mode = "rgmii"; 149 phy-handle = <&phy0>; 150 151 mdio { 152 #address-cells = <1>; 153 #size-cells = <0>; 154 155 phy0: ethernet-phy@0 { 156 reg = <0>; 157 }; 158 159 phy1: ethernet-phy@1 { 160 reg = <1>; 161 }; 162 }; 163 }; 164 165 /* EthC */ 166 ethernet@c800a000 { 167 status = "ok"; 168 queue-rx = <&qmgr 4>; 169 queue-txready = <&qmgr 21>; 170 phy-mode = "rgmii"; 171 phy-handle = <&phy1>; 172 }; 173 }; 174};