opp2420_data.c (5057B)
1// SPDX-License-Identifier: GPL-2.0 2/* 3 * opp2420_data.c - old-style "OPP" table for OMAP2420 4 * 5 * Copyright (C) 2005-2009 Texas Instruments, Inc. 6 * Copyright (C) 2004-2009 Nokia Corporation 7 * 8 * Richard Woodruff <r-woodruff2@ti.com> 9 * 10 * The OMAP2 processor can be run at several discrete 'PRCM configurations'. 11 * These configurations are characterized by voltage and speed for clocks. 12 * The device is only validated for certain combinations. One way to express 13 * these combinations is via the 'ratios' which the clocks operate with 14 * respect to each other. These ratio sets are for a given voltage/DPLL 15 * setting. All configurations can be described by a DPLL setting and a ratio. 16 * 17 * XXX Missing voltage data. 18 * XXX Missing 19.2MHz sys_clk rate sets (needed for N800/N810) 19 * 20 * THe format described in this file is deprecated. Once a reasonable 21 * OPP API exists, the data in this file should be converted to use it. 22 * 23 * This is technically part of the OMAP2xxx clock code. 24 * 25 * Considerable work is still needed to fully support dynamic frequency 26 * changes on OMAP2xxx-series chips. Readers interested in such a 27 * project are encouraged to review the Maemo Diablo RX-34 and RX-44 28 * kernel source at: 29 * http://repository.maemo.org/pool/diablo/free/k/kernel-source-diablo/ 30 */ 31 32#include <linux/kernel.h> 33 34#include "opp2xxx.h" 35#include "sdrc.h" 36#include "clock.h" 37 38/* 39 * Key dividers which make up a PRCM set. Ratios for a PRCM are mandated. 40 * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU, 41 * CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL, 42 * CM_CLKSEL2_PLL, CM_CLKSEL_MDM 43 * 44 * Filling in table based on H4 boards available. There are quite a 45 * few more rate combinations which could be defined. 46 * 47 * When multiple values are defined the start up will try and choose 48 * the fastest one. If a 'fast' value is defined, then automatically, 49 * the /2 one should be included as it can be used. Generally having 50 * more than one fast set does not make sense, as static timings need 51 * to be changed to change the set. The exception is the bypass 52 * setting which is available for low power bypass. 53 * 54 * Note: This table needs to be sorted, fastest to slowest. 55 **/ 56const struct prcm_config omap2420_rate_table[] = { 57 /* PRCM I - FAST */ 58 {S12M, S660M, S330M, RI_CM_CLKSEL_MPU_VAL, /* 330MHz ARM */ 59 RI_CM_CLKSEL_DSP_VAL, RI_CM_CLKSEL_GFX_VAL, 60 RI_CM_CLKSEL1_CORE_VAL, MI_CM_CLKSEL1_PLL_12_VAL, 61 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_165MHz, 62 RATE_IN_242X}, 63 64 /* PRCM II - FAST */ 65 {S12M, S600M, S300M, RII_CM_CLKSEL_MPU_VAL, /* 300MHz ARM */ 66 RII_CM_CLKSEL_DSP_VAL, RII_CM_CLKSEL_GFX_VAL, 67 RII_CM_CLKSEL1_CORE_VAL, MII_CM_CLKSEL1_PLL_12_VAL, 68 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_100MHz, 69 RATE_IN_242X}, 70 71 {S13M, S600M, S300M, RII_CM_CLKSEL_MPU_VAL, /* 300MHz ARM */ 72 RII_CM_CLKSEL_DSP_VAL, RII_CM_CLKSEL_GFX_VAL, 73 RII_CM_CLKSEL1_CORE_VAL, MII_CM_CLKSEL1_PLL_13_VAL, 74 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_100MHz, 75 RATE_IN_242X}, 76 77 /* PRCM III - FAST */ 78 {S12M, S532M, S266M, RIII_CM_CLKSEL_MPU_VAL, /* 266MHz ARM */ 79 RIII_CM_CLKSEL_DSP_VAL, RIII_CM_CLKSEL_GFX_VAL, 80 RIII_CM_CLKSEL1_CORE_VAL, MIII_CM_CLKSEL1_PLL_12_VAL, 81 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_133MHz, 82 RATE_IN_242X}, 83 84 {S13M, S532M, S266M, RIII_CM_CLKSEL_MPU_VAL, /* 266MHz ARM */ 85 RIII_CM_CLKSEL_DSP_VAL, RIII_CM_CLKSEL_GFX_VAL, 86 RIII_CM_CLKSEL1_CORE_VAL, MIII_CM_CLKSEL1_PLL_13_VAL, 87 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_133MHz, 88 RATE_IN_242X}, 89 90 /* PRCM II - SLOW */ 91 {S12M, S300M, S150M, RII_CM_CLKSEL_MPU_VAL, /* 150MHz ARM */ 92 RII_CM_CLKSEL_DSP_VAL, RII_CM_CLKSEL_GFX_VAL, 93 RII_CM_CLKSEL1_CORE_VAL, MII_CM_CLKSEL1_PLL_12_VAL, 94 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_100MHz, 95 RATE_IN_242X}, 96 97 {S13M, S300M, S150M, RII_CM_CLKSEL_MPU_VAL, /* 150MHz ARM */ 98 RII_CM_CLKSEL_DSP_VAL, RII_CM_CLKSEL_GFX_VAL, 99 RII_CM_CLKSEL1_CORE_VAL, MII_CM_CLKSEL1_PLL_13_VAL, 100 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_100MHz, 101 RATE_IN_242X}, 102 103 /* PRCM III - SLOW */ 104 {S12M, S266M, S133M, RIII_CM_CLKSEL_MPU_VAL, /* 133MHz ARM */ 105 RIII_CM_CLKSEL_DSP_VAL, RIII_CM_CLKSEL_GFX_VAL, 106 RIII_CM_CLKSEL1_CORE_VAL, MIII_CM_CLKSEL1_PLL_12_VAL, 107 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_133MHz, 108 RATE_IN_242X}, 109 110 {S13M, S266M, S133M, RIII_CM_CLKSEL_MPU_VAL, /* 133MHz ARM */ 111 RIII_CM_CLKSEL_DSP_VAL, RIII_CM_CLKSEL_GFX_VAL, 112 RIII_CM_CLKSEL1_CORE_VAL, MIII_CM_CLKSEL1_PLL_13_VAL, 113 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_133MHz, 114 RATE_IN_242X}, 115 116 /* PRCM-VII (boot-bypass) */ 117 {S12M, S12M, S12M, RVII_CM_CLKSEL_MPU_VAL, /* 12MHz ARM*/ 118 RVII_CM_CLKSEL_DSP_VAL, RVII_CM_CLKSEL_GFX_VAL, 119 RVII_CM_CLKSEL1_CORE_VAL, MVII_CM_CLKSEL1_PLL_12_VAL, 120 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_BYPASS, 121 RATE_IN_242X}, 122 123 /* PRCM-VII (boot-bypass) */ 124 {S13M, S13M, S13M, RVII_CM_CLKSEL_MPU_VAL, /* 13MHz ARM */ 125 RVII_CM_CLKSEL_DSP_VAL, RVII_CM_CLKSEL_GFX_VAL, 126 RVII_CM_CLKSEL1_CORE_VAL, MVII_CM_CLKSEL1_PLL_13_VAL, 127 MX_CLKSEL2_PLL_2x_VAL, 0, SDRC_RFR_CTRL_BYPASS, 128 RATE_IN_242X}, 129 130 { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, 131};