pcm990_baseboard.h (8142B)
1/* SPDX-License-Identifier: GPL-2.0-or-later */ 2/* 3 * arch/arm/mach-pxa/include/mach/pcm990_baseboard.h 4 * 5 * (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de> 6 * (c) 2007 Juergen Beisert <j.beisert@pengutronix.de> 7 */ 8 9#include "pcm027.h" 10#include "irqs.h" /* PXA_GPIO_TO_IRQ */ 11 12/* 13 * definitions relevant only when the PCM-990 14 * development base board is in use 15 */ 16 17/* CPLD's interrupt controller is connected to PCM-027 GPIO 9 */ 18#define PCM990_CTRL_INT_IRQ_GPIO 9 19#define PCM990_CTRL_INT_IRQ PXA_GPIO_TO_IRQ(PCM990_CTRL_INT_IRQ_GPIO) 20#define PCM990_CTRL_INT_IRQ_EDGE IRQ_TYPE_EDGE_RISING 21#define PCM990_CTRL_PHYS PXA_CS1_PHYS /* 16-Bit */ 22#define PCM990_CTRL_SIZE (1*1024*1024) 23 24#define PCM990_CTRL_PWR_IRQ_GPIO 14 25#define PCM990_CTRL_PWR_IRQ PXA_GPIO_TO_IRQ(PCM990_CTRL_PWR_IRQ_GPIO) 26#define PCM990_CTRL_PWR_IRQ_EDGE IRQ_TYPE_EDGE_RISING 27 28/* visible CPLD (U7) registers */ 29#define PCM990_CTRL_REG0 0x0000 /* RESET REGISTER */ 30#define PCM990_CTRL_SYSRES 0x0001 /* System RESET REGISTER */ 31#define PCM990_CTRL_RESOUT 0x0002 /* RESETOUT Enable REGISTER */ 32#define PCM990_CTRL_RESGPIO 0x0004 /* RESETGPIO Enable REGISTER */ 33 34#define PCM990_CTRL_REG1 0x0002 /* Power REGISTER */ 35#define PCM990_CTRL_5VOFF 0x0001 /* Disable 5V Regulators */ 36#define PCM990_CTRL_CANPWR 0x0004 /* Enable CANPWR ADUM */ 37#define PCM990_CTRL_PM_5V 0x0008 /* Read 5V OK */ 38 39#define PCM990_CTRL_REG2 0x0004 /* LED REGISTER */ 40#define PCM990_CTRL_LEDPWR 0x0001 /* POWER LED enable */ 41#define PCM990_CTRL_LEDBAS 0x0002 /* BASIS LED enable */ 42#define PCM990_CTRL_LEDUSR 0x0004 /* USER LED enable */ 43 44#define PCM990_CTRL_REG3 0x0006 /* LCD CTRL REGISTER 3 */ 45#define PCM990_CTRL_LCDPWR 0x0001 /* RW LCD Power on */ 46#define PCM990_CTRL_LCDON 0x0002 /* RW LCD Latch on */ 47#define PCM990_CTRL_LCDPOS1 0x0004 /* RW POS 1 */ 48#define PCM990_CTRL_LCDPOS2 0x0008 /* RW POS 2 */ 49 50#define PCM990_CTRL_REG4 0x0008 /* MMC1 CTRL REGISTER 4 */ 51#define PCM990_CTRL_MMC1PWR 0x0001 /* RW MMC1 Power on */ 52 53#define PCM990_CTRL_REG5 0x000A /* MMC2 CTRL REGISTER 5 */ 54#define PCM990_CTRL_MMC2PWR 0x0001 /* RW MMC2 Power on */ 55#define PCM990_CTRL_MMC2LED 0x0002 /* RW MMC2 LED */ 56#define PCM990_CTRL_MMC2DE 0x0004 /* R MMC2 Card detect */ 57#define PCM990_CTRL_MMC2WP 0x0008 /* R MMC2 Card write protect */ 58 59#define PCM990_CTRL_INTSETCLR 0x000C /* Interrupt Clear REGISTER */ 60#define PCM990_CTRL_INTC0 0x0001 /* Clear Reg BT Detect */ 61#define PCM990_CTRL_INTC1 0x0002 /* Clear Reg FR RI */ 62#define PCM990_CTRL_INTC2 0x0004 /* Clear Reg MMC1 Detect */ 63#define PCM990_CTRL_INTC3 0x0008 /* Clear Reg PM_5V off */ 64 65#define PCM990_CTRL_INTMSKENA 0x000E /* Interrupt Enable REGISTER */ 66#define PCM990_CTRL_ENAINT0 0x0001 /* Enable Int BT Detect */ 67#define PCM990_CTRL_ENAINT1 0x0002 /* Enable Int FR RI */ 68#define PCM990_CTRL_ENAINT2 0x0004 /* Enable Int MMC1 Detect */ 69#define PCM990_CTRL_ENAINT3 0x0008 /* Enable Int PM_5V off */ 70 71#define PCM990_CTRL_REG8 0x0014 /* Uart REGISTER */ 72#define PCM990_CTRL_FFSD 0x0001 /* BT Uart Enable */ 73#define PCM990_CTRL_BTSD 0x0002 /* FF Uart Enable */ 74#define PCM990_CTRL_FFRI 0x0004 /* FF Uart RI detect */ 75#define PCM990_CTRL_BTRX 0x0008 /* BT Uart Rx detect */ 76 77#define PCM990_CTRL_REG9 0x0010 /* AC97 Flash REGISTER */ 78#define PCM990_CTRL_FLWP 0x0001 /* pC Flash Write Protect */ 79#define PCM990_CTRL_FLDIS 0x0002 /* pC Flash Disable */ 80#define PCM990_CTRL_AC97ENA 0x0004 /* Enable AC97 Expansion */ 81 82#define PCM990_CTRL_REG10 0x0012 /* GPS-REGISTER */ 83#define PCM990_CTRL_GPSPWR 0x0004 /* GPS-Modul Power on */ 84#define PCM990_CTRL_GPSENA 0x0008 /* GPS-Modul Enable */ 85 86#define PCM990_CTRL_REG11 0x0014 /* Accu REGISTER */ 87#define PCM990_CTRL_ACENA 0x0001 /* Charge Enable */ 88#define PCM990_CTRL_ACSEL 0x0002 /* Charge Akku -> DC Enable */ 89#define PCM990_CTRL_ACPRES 0x0004 /* DC Present */ 90#define PCM990_CTRL_ACALARM 0x0008 /* Error Akku */ 91 92/* 93 * IDE 94 */ 95#define PCM990_IDE_IRQ_GPIO 13 96#define PCM990_IDE_IRQ PXA_GPIO_TO_IRQ(PCM990_IDE_IRQ_GPIO) 97#define PCM990_IDE_IRQ_EDGE IRQ_TYPE_EDGE_RISING 98#define PCM990_IDE_PLD_PHYS 0x20000000 /* 16 bit wide */ 99#define PCM990_IDE_PLD_BASE 0xee000000 100#define PCM990_IDE_PLD_SIZE (1*1024*1024) 101 102/* visible CPLD (U6) registers */ 103#define PCM990_IDE_PLD_REG0 0x1000 /* OFFSET IDE REGISTER 0 */ 104#define PCM990_IDE_PM5V 0x0004 /* R System VCC_5V */ 105#define PCM990_IDE_STBY 0x0008 /* R System StandBy */ 106 107#define PCM990_IDE_PLD_REG1 0x1002 /* OFFSET IDE REGISTER 1 */ 108#define PCM990_IDE_IDEMODE 0x0001 /* R TrueIDE Mode */ 109#define PCM990_IDE_DMAENA 0x0004 /* RW DMA Enable */ 110#define PCM990_IDE_DMA1_0 0x0008 /* RW 1=DREQ1 0=DREQ0 */ 111 112#define PCM990_IDE_PLD_REG2 0x1004 /* OFFSET IDE REGISTER 2 */ 113#define PCM990_IDE_RESENA 0x0001 /* RW IDE Reset Bit enable */ 114#define PCM990_IDE_RES 0x0002 /* RW IDE Reset Bit */ 115#define PCM990_IDE_RDY 0x0008 /* RDY */ 116 117#define PCM990_IDE_PLD_REG3 0x1006 /* OFFSET IDE REGISTER 3 */ 118#define PCM990_IDE_IDEOE 0x0001 /* RW Latch on Databus */ 119#define PCM990_IDE_IDEON 0x0002 /* RW Latch on Control Address */ 120#define PCM990_IDE_IDEIN 0x0004 /* RW Latch on Interrupt usw. */ 121 122#define PCM990_IDE_PLD_REG4 0x1008 /* OFFSET IDE REGISTER 4 */ 123#define PCM990_IDE_PWRENA 0x0001 /* RW IDE Power enable */ 124#define PCM990_IDE_5V 0x0002 /* R IDE Power 5V */ 125#define PCM990_IDE_PWG 0x0008 /* R IDE Power is on */ 126 127#define PCM990_IDE_PLD_P2V(x) ((x) - PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_BASE) 128#define PCM990_IDE_PLD_V2P(x) ((x) - PCM990_IDE_PLD_BASE + PCM990_IDE_PLD_PHYS) 129 130/* 131 * Compact Flash 132 */ 133#define PCM990_CF_IRQ_GPIO 11 134#define PCM990_CF_IRQ PXA_GPIO_TO_IRQ(PCM990_CF_IRQ_GPIO) 135#define PCM990_CF_IRQ_EDGE IRQ_TYPE_EDGE_RISING 136 137#define PCM990_CF_CD_GPIO 12 138#define PCM990_CF_CD PXA_GPIO_TO_IRQ(PCM990_CF_CD_GPIO) 139#define PCM990_CF_CD_EDGE IRQ_TYPE_EDGE_RISING 140 141#define PCM990_CF_PLD_PHYS 0x30000000 /* 16 bit wide */ 142 143/* visible CPLD (U6) registers */ 144#define PCM990_CF_PLD_REG0 0x1000 /* OFFSET CF REGISTER 0 */ 145#define PCM990_CF_REG0_LED 0x0001 /* RW LED on */ 146#define PCM990_CF_REG0_BLK 0x0002 /* RW LED flash when access */ 147#define PCM990_CF_REG0_PM5V 0x0004 /* R System VCC_5V enable */ 148#define PCM990_CF_REG0_STBY 0x0008 /* R System StandBy */ 149 150#define PCM990_CF_PLD_REG1 0x1002 /* OFFSET CF REGISTER 1 */ 151#define PCM990_CF_REG1_IDEMODE 0x0001 /* RW CF card run as TrueIDE */ 152#define PCM990_CF_REG1_CF0 0x0002 /* RW CF card at ADDR 0x28000000 */ 153 154#define PCM990_CF_PLD_REG2 0x1004 /* OFFSET CF REGISTER 2 */ 155#define PCM990_CF_REG2_RES 0x0002 /* RW CF RESET BIT */ 156#define PCM990_CF_REG2_RDYENA 0x0004 /* RW Enable CF_RDY */ 157#define PCM990_CF_REG2_RDY 0x0008 /* R CF_RDY auf PWAIT */ 158 159#define PCM990_CF_PLD_REG3 0x1006 /* OFFSET CF REGISTER 3 */ 160#define PCM990_CF_REG3_CFOE 0x0001 /* RW Latch on Databus */ 161#define PCM990_CF_REG3_CFON 0x0002 /* RW Latch on Control Address */ 162#define PCM990_CF_REG3_CFIN 0x0004 /* RW Latch on Interrupt usw. */ 163#define PCM990_CF_REG3_CFCD 0x0008 /* RW Latch on CD1/2 VS1/2 usw */ 164 165#define PCM990_CF_PLD_REG4 0x1008 /* OFFSET CF REGISTER 4 */ 166#define PCM990_CF_REG4_PWRENA 0x0001 /* RW CF Power on (CD1/2 = "00") */ 167#define PCM990_CF_REG4_5_3V 0x0002 /* RW 1 = 5V CF_VCC 0 = 3 V CF_VCC */ 168#define PCM990_CF_REG4_3B 0x0004 /* RW 3.0V Backup from VCC (5_3V=0) */ 169#define PCM990_CF_REG4_PWG 0x0008 /* R CF-Power is on */ 170 171#define PCM990_CF_PLD_REG5 0x100A /* OFFSET CF REGISTER 5 */ 172#define PCM990_CF_REG5_BVD1 0x0001 /* R CF /BVD1 */ 173#define PCM990_CF_REG5_BVD2 0x0002 /* R CF /BVD2 */ 174#define PCM990_CF_REG5_VS1 0x0004 /* R CF /VS1 */ 175#define PCM990_CF_REG5_VS2 0x0008 /* R CF /VS2 */ 176 177#define PCM990_CF_PLD_REG6 0x100C /* OFFSET CF REGISTER 6 */ 178#define PCM990_CF_REG6_CD1 0x0001 /* R CF Card_Detect1 */ 179#define PCM990_CF_REG6_CD2 0x0002 /* R CF Card_Detect2 */ 180 181/* 182 * Wolfson AC97 Touch 183 */ 184#define PCM990_AC97_IRQ_GPIO 10 185#define PCM990_AC97_IRQ PXA_GPIO_TO_IRQ(PCM990_AC97_IRQ_GPIO) 186#define PCM990_AC97_IRQ_EDGE IRQ_TYPE_EDGE_RISING 187 188/* 189 * MMC phyCORE 190 */ 191#define PCM990_MMC0_IRQ_GPIO 9 192#define PCM990_MMC0_IRQ PXA_GPIO_TO_IRQ(PCM990_MMC0_IRQ_GPIO) 193#define PCM990_MMC0_IRQ_EDGE IRQ_TYPE_EDGE_FALLING 194 195/* 196 * USB phyCore 197 */ 198#define PCM990_USB_OVERCURRENT (88 | GPIO_ALT_FN_1_IN) 199#define PCM990_USB_PWR_EN (89 | GPIO_ALT_FN_2_OUT)