regs-u2d.h (11067B)
1/* SPDX-License-Identifier: GPL-2.0 */ 2#ifndef __ASM_ARCH_PXA3xx_U2D_H 3#define __ASM_ARCH_PXA3xx_U2D_H 4 5/* 6 * USB2 device controller registers and bits definitions 7 */ 8#define U2DCR (0x0000) /* U2D Control Register */ 9#define U2DCR_NDC (1 << 31) /* NAK During Config */ 10#define U2DCR_HSTC (0x7 << 28) /* High Speed Timeout Calibration */ 11#define U2DCR_SPEOREN (1 << 27) /* Short Packet EOR INTR generation Enable */ 12#define U2DCR_FSTC (0x7 << 24) /* Full Speed Timeout Calibration */ 13#define U2DCR_UCLKOVR (1 << 22) /* UTM Clock Override */ 14#define U2DCR_ABP (1 << 21) /* Application Bus Power */ 15#define U2DCR_ADD (1 << 20) /* Application Device Disconnect */ 16#define U2DCR_CC (1 << 19) /* Configuration Change */ 17#define U2DCR_HS (1 << 18) /* High Speed USB Detection */ 18#define U2DCR_SMAC (1 << 17) /* Switch Endpoint Memory to Active Configuration */ 19#define U2DCR_DWRE (1 << 16) /* Device Remote Wake-up Feature */ 20#define U2DCR_ACN (0xf << 12) /* Active U2D Configuration Number */ 21#define U2DCR_AIN (0xf << 8) /* Active U2D Interface Number */ 22#define U2DCR_AAISN (0xf << 4) /* Active U2D Alternate Interface Setting Number */ 23#define U2DCR_EMCE (1 << 3) /* Endpoint Memory Configuration Error */ 24#define U2DCR_UDR (1 << 2) /* U2D Resume */ 25#define U2DCR_UDA (1 << 1) /* U2D Active */ 26#define U2DCR_UDE (1 << 0) /* U2D Enable */ 27 28#define U2DICR (0x0004) /* U2D Interrupt Control Register */ 29#define U2DISR (0x000C) /* U2D Interrupt Status Register */ 30#define U2DINT_CC (1 << 31) /* Interrupt - Configuration Change */ 31#define U2DINT_SOF (1 << 30) /* Interrupt - SOF */ 32#define U2DINT_USOF (1 << 29) /* Interrupt - micro SOF */ 33#define U2DINT_RU (1 << 28) /* Interrupt - Resume */ 34#define U2DINT_SU (1 << 27) /* Interrupt - Suspend */ 35#define U2DINT_RS (1 << 26) /* Interrupt - Reset */ 36#define U2DINT_DPE (1 << 25) /* Interrupt - Data Packet Error */ 37#define U2DINT_FIFOERR (0x4) /* Interrupt - endpoint FIFO error */ 38#define U2DINT_PACKETCMP (0x2) /* Interrupt - endpoint packet complete */ 39#define U2DINT_SPACKETCMP (0x1) /* Interrupt - endpoint short packet complete */ 40 41#define U2DFNR (0x0014) /* U2D Frame Number Register */ 42 43#define U2DINT(n, intr) (((intr) & 0x07) << (((n) & 0x07) * 3)) 44#define U2DICR2 (0x0008) /* U2D Interrupt Control Register 2 */ 45#define U2DISR2 (0x0010) /* U2D Interrupt Status Register 2 */ 46 47#define U2DOTGCR (0x0020) /* U2D OTG Control Register */ 48#define U2DOTGCR_OTGEN (1 << 31) /* On-The-Go Enable */ 49#define U2DOTGCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation Protocal Port Support */ 50#define U2DOTGCR_AHNP (1 << 29) /* A-device Host Negotiation Protocal Support */ 51#define U2DOTGCR_BHNP (1 << 28) /* B-device Host Negotiation Protocal Enable */ 52 53#ifdef CONFIG_CPU_PXA930 54#define U2DOTGCR_LPA (1 << 15) /* ULPI low power mode active */ 55#define U2DOTGCR_IESI (1 << 13) /* OTG interrupt Enable */ 56#define U2DOTGCR_ISSI (1 << 12) /* OTG interrupt status */ 57#endif 58 59#define U2DOTGCR_CKAF (1 << 5) /* Carkit Mode Alternate Function Select */ 60#define U2DOTGCR_UTMID (1 << 4) /* UTMI Interface Disable */ 61#define U2DOTGCR_ULAF (1 << 3) /* ULPI Mode Alternate Function Select */ 62#define U2DOTGCR_SMAF (1 << 2) /* Serial Mode Alternate Function Select */ 63#define U2DOTGCR_RTSM (1 << 1) /* Return to Synchronous Mode (ULPI Mode) */ 64#define U2DOTGCR_ULE (1 << 0) /* ULPI Wrapper Enable */ 65 66#define U2DOTGICR (0x0024) /* U2D OTG Interrupt Control Register */ 67#define U2DOTGISR (0x0028) /* U2D OTG Interrupt Status Register */ 68 69#define U2DOTGINT_SF (1 << 17) /* OTG Set Feature Command Received */ 70#define U2DOTGINT_SI (1 << 16) /* OTG Interrupt */ 71#define U2DOTGINT_RLS1 (1 << 14) /* RXCMD Linestate[1] Change Interrupt Rise */ 72#define U2DOTGINT_RLS0 (1 << 13) /* RXCMD Linestate[0] Change Interrupt Rise */ 73#define U2DOTGINT_RID (1 << 12) /* RXCMD OTG ID Change Interrupt Rise */ 74#define U2DOTGINT_RSE (1 << 11) /* RXCMD OTG Session End Interrupt Rise */ 75#define U2DOTGINT_RSV (1 << 10) /* RXCMD OTG Session Valid Interrupt Rise */ 76#define U2DOTGINT_RVV (1 << 9) /* RXCMD OTG Vbus Valid Interrupt Rise */ 77#define U2DOTGINT_RCK (1 << 8) /* RXCMD Carkit Interrupt Rise */ 78#define U2DOTGINT_FLS1 (1 << 6) /* RXCMD Linestate[1] Change Interrupt Fall */ 79#define U2DOTGINT_FLS0 (1 << 5) /* RXCMD Linestate[0] Change Interrupt Fall */ 80#define U2DOTGINT_FID (1 << 4) /* RXCMD OTG ID Change Interrupt Fall */ 81#define U2DOTGINT_FSE (1 << 3) /* RXCMD OTG Session End Interrupt Fall */ 82#define U2DOTGINT_FSV (1 << 2) /* RXCMD OTG Session Valid Interrupt Fall */ 83#define U2DOTGINT_FVV (1 << 1) /* RXCMD OTG Vbus Valid Interrupt Fall */ 84#define U2DOTGINT_FCK (1 << 0) /* RXCMD Carkit Interrupt Fall */ 85 86#define U2DOTGUSR (0x002C) /* U2D OTG ULPI Status Register */ 87#define U2DOTGUSR_LPA (1 << 31) /* ULPI Low Power Mode Active */ 88#define U2DOTGUSR_S6A (1 << 30) /* ULPI Serial Mode (6-pin) Active */ 89#define U2DOTGUSR_S3A (1 << 29) /* ULPI Serial Mode (3-pin) Active */ 90#define U2DOTGUSR_CKA (1 << 28) /* ULPI Car Kit Mode Active */ 91#define U2DOTGUSR_LS1 (1 << 6) /* RXCMD Linestate 1 Status */ 92#define U2DOTGUSR_LS0 (1 << 5) /* RXCMD Linestate 0 Status */ 93#define U2DOTGUSR_ID (1 << 4) /* OTG IDGnd Status */ 94#define U2DOTGUSR_SE (1 << 3) /* OTG Session End Status */ 95#define U2DOTGUSR_SV (1 << 2) /* OTG Session Valid Status */ 96#define U2DOTGUSR_VV (1 << 1) /* OTG Vbus Valid Status */ 97#define U2DOTGUSR_CK (1 << 0) /* Carkit Interrupt Status */ 98 99#define U2DOTGUCR (0x0030) /* U2D OTG ULPI Control Register */ 100#define U2DOTGUCR_RUN (1 << 25) /* RUN */ 101#define U2DOTGUCR_RNW (1 << 24) /* Read or Write operation */ 102#define U2DOTGUCR_ADDR (0x3f << 16) /* Address of the ULPI PHY register */ 103#define U2DOTGUCR_WDATA (0xff << 8) /* The data for a WRITE command */ 104#define U2DOTGUCR_RDATA (0xff << 0) /* The data for a READ command */ 105 106#define U2DP3CR (0x0034) /* U2D Port 3 Control Register */ 107#define U2DP3CR_P2SS (0x3 << 8) /* Host Port 2 Serial Mode Select */ 108#define U2DP3CR_P3SS (0x7 << 4) /* Host Port 3 Serial Mode Select */ 109#define U2DP3CR_VPVMBEN (0x1 << 2) /* Host Port 3 Vp/Vm Block Enable */ 110#define U2DP3CR_CFG (0x3 << 0) /* Host Port 3 Configuration */ 111 112#define U2DCSR0 (0x0100) /* U2D Control/Status Register - Endpoint 0 */ 113#define U2DCSR0_IPA (1 << 8) /* IN Packet Adjusted */ 114#define U2DCSR0_SA (1 << 7) /* SETUP Active */ 115#define U2DCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */ 116#define U2DCSR0_FST (1 << 5) /* Force Stall */ 117#define U2DCSR0_SST (1 << 4) /* Send Stall */ 118#define U2DCSR0_DME (1 << 3) /* DMA Enable */ 119#define U2DCSR0_FTF (1 << 2) /* Flush Transmit FIFO */ 120#define U2DCSR0_IPR (1 << 1) /* IN Packet Ready */ 121#define U2DCSR0_OPC (1 << 0) /* OUT Packet Complete */ 122 123#define U2DCSR(x) (0x0100 + ((x) << 2)) /* U2D Control/Status Register - Endpoint x */ 124#define U2DCSR_BF (1 << 10) /* Buffer Full, for OUT eps */ 125#define U2DCSR_BE (1 << 10) /* Buffer Empty, for IN eps */ 126#define U2DCSR_DPE (1 << 9) /* Data Packet Error, for ISO eps only */ 127#define U2DCSR_FEF (1 << 8) /* Flush Endpoint FIFO */ 128#define U2DCSR_SP (1 << 7) /* Short Packet Control/Status, for OUT eps only, readonly */ 129#define U2DCSR_BNE (1 << 6) /* Buffer Not Empty, for OUT eps */ 130#define U2DCSR_BNF (1 << 6) /* Buffer Not Full, for IN eps */ 131#define U2DCSR_FST (1 << 5) /* Force STALL, write 1 set */ 132#define U2DCSR_SST (1 << 4) /* Sent STALL, write 1 clear */ 133#define U2DCSR_DME (1 << 3) /* DMA Enable */ 134#define U2DCSR_TRN (1 << 2) /* Tx/Rx NAK, write 1 clear */ 135#define U2DCSR_PC (1 << 1) /* Packet Complete, write 1 clear */ 136#define U2DCSR_FS (1 << 0) /* FIFO needs Service */ 137 138#define U2DBCR0 (0x0200) /* U2D Byte Count Register - Endpoint 0 */ 139#define U2DBCR(x) (0x0200 + ((x) << 2)) /* U2D Byte Count Register - Endpoint x */ 140 141#define U2DDR0 (0x0300) /* U2D Data Register - Endpoint 0 */ 142 143#define U2DEPCR(x) (0x0400 + ((x) << 2)) /* U2D Configuration Register - Endpoint x */ 144#define U2DEPCR_EE (1 << 0) /* Endpoint Enable */ 145#define U2DEPCR_BS_MASK (0x3FE) /* Buffer Size, BS*8=FIFO size, max 8184B = 8KB */ 146 147#define U2DSCA (0x0500) /* U2D Setup Command Address */ 148#define U2DSCA_VALUE (0x0120) 149 150#define U2DEN0 (0x0504) /* U2D Endpoint Information Register - Endpoint 0 */ 151#define U2DEN(x) (0x0504 + ((x) << 2)) /* U2D Endpoint Information Register - Endpoint x */ 152 153/* U2DMA registers */ 154#define U2DMACSR0 (0x1000) /* U2DMA Control/Status Register - Channel 0 */ 155#define U2DMACSR(x) (0x1000 + ((x) << 2)) /* U2DMA Control/Status Register - Channel x */ 156#define U2DMACSR_RUN (1 << 31) /* Run Bit (read / write) */ 157#define U2DMACSR_STOPIRQEN (1 << 29) /* Stop Interrupt Enable (read / write) */ 158#define U2DMACSR_EORIRQEN (1 << 28) /* End of Receive Interrupt Enable (R/W) */ 159#define U2DMACSR_EORJMPEN (1 << 27) /* Jump to next descriptor on EOR */ 160#define U2DMACSR_EORSTOPEN (1 << 26) /* STOP on an EOR */ 161#define U2DMACSR_RASIRQEN (1 << 23) /* Request After Cnannel Stopped Interrupt Enable */ 162#define U2DMACSR_MASKRUN (1 << 22) /* Mask Run */ 163#define U2DMACSR_SCEMC (3 << 18) /* System Bus Split Completion Error Message Class */ 164#define U2DMACSR_SCEMI (0x1f << 13) /* System Bus Split Completion Error Message Index */ 165#define U2DMACSR_BUSERRTYPE (7 << 10) /* PX Bus Error Type */ 166#define U2DMACSR_EORINTR (1 << 9) /* End Of Receive */ 167#define U2DMACSR_REQPEND (1 << 8) /* Request Pending */ 168#define U2DMACSR_RASINTR (1 << 4) /* Request After Channel Stopped (read / write 1 clear) */ 169#define U2DMACSR_STOPINTR (1 << 3) /* Stop Interrupt (read only) */ 170#define U2DMACSR_ENDINTR (1 << 2) /* End Interrupt (read / write 1 clear) */ 171#define U2DMACSR_STARTINTR (1 << 1) /* Start Interrupt (read / write 1 clear) */ 172#define U2DMACSR_BUSERRINTR (1 << 0) /* Bus Error Interrupt (read / write 1 clear) */ 173 174#define U2DMACR (0x1080) /* U2DMA Control Register */ 175#define U2DMAINT (0x10F0) /* U2DMA Interrupt Register */ 176 177#define U2DMABR0 (0x1100) /* U2DMA Branch Register - Channel 0 */ 178#define U2DMABR(x) (0x1100 + (x) << 2) /* U2DMA Branch Register - Channel x */ 179 180#define U2DMADADR0 (0x1200) /* U2DMA Descriptor Address Register - Channel 0 */ 181#define U2DMADADR(x) (0x1200 + (x) * 0x10) /* U2DMA Descriptor Address Register - Channel x */ 182 183#define U2DMADADR_STOP (1U << 0) 184 185#define U2DMASADR0 (0x1204) /* U2DMA Source Address Register - Channel 0 */ 186#define U2DMASADR(x) (0x1204 + (x) * 0x10) /* U2DMA Source Address Register - Channel x */ 187#define U2DMATADR0 (0x1208) /* U2DMA Target Address Register - Channel 0 */ 188#define U2DMATADR(x) (0x1208 + (x) * 0x10) /* U2DMA Target Address Register - Channel x */ 189 190#define U2DMACMDR0 (0x120C) /* U2DMA Command Address Register - Channel 0 */ 191#define U2DMACMDR(x) (0x120C + (x) * 0x10) /* U2DMA Command Address Register - Channel x */ 192 193#define U2DMACMDR_XFRDIS (1 << 31) /* Transfer Direction */ 194#define U2DMACMDR_STARTIRQEN (1 << 22) /* Start Interrupt Enable */ 195#define U2DMACMDR_ENDIRQEN (1 << 21) /* End Interrupt Enable */ 196#define U2DMACMDR_PACKCOMP (1 << 13) /* Packet Complete */ 197#define U2DMACMDR_LEN (0x07ff) /* length mask (max = 2K - 1) */ 198 199#endif /* __ASM_ARCH_PXA3xx_U2D_H */