Kconfig.platform (4478B)
1# SPDX-License-Identifier: GPL-2.0-only 2menu "Platform options" 3 4comment "Memory settings" 5 6config NIOS2_MEM_BASE 7 hex "Memory base address" 8 default "0x00000000" 9 help 10 This is the physical address of the memory that the kernel will run 11 from. This address is used to link the kernel and setup initial memory 12 management. You should take the raw memory address without any MMU 13 or cache bits set. 14 Please not that this address is used directly so you have to manually 15 do address translation if it's connected to a bridge. 16 17comment "Device tree" 18 19config NIOS2_DTB_AT_PHYS_ADDR 20 bool "DTB at physical address" 21 help 22 When enabled you can select a physical address to load the dtb from. 23 Normally this address is passed by a bootloader such as u-boot but 24 using this you can use a devicetree without a bootloader. 25 This way you can store a devicetree in NOR flash or an onchip rom. 26 Please note that this address is used directly so you have to manually 27 do address translation if it's connected to a bridge. Also take into 28 account that when using an MMU you'd have to ad 0xC0000000 to your 29 address 30 31config NIOS2_DTB_PHYS_ADDR 32 hex "DTB Address" 33 depends on NIOS2_DTB_AT_PHYS_ADDR 34 default "0xC0000000" 35 help 36 Physical address of a dtb blob. 37 38config NIOS2_DTB_SOURCE_BOOL 39 bool "Compile and link device tree into kernel image" 40 depends on !COMPILE_TEST 41 help 42 This allows you to specify a dts (device tree source) file 43 which will be compiled and linked into the kernel image. 44 45config NIOS2_DTB_SOURCE 46 string "Device tree source file" 47 depends on NIOS2_DTB_SOURCE_BOOL 48 default "" 49 help 50 Absolute path to the device tree source (dts) file describing your 51 system. 52 53comment "Nios II instructions" 54 55config NIOS2_ARCH_REVISION 56 int "Select Nios II architecture revision" 57 range 1 2 58 default 1 59 help 60 Select between Nios II R1 and Nios II R2 . The architectures 61 are binary incompatible. Default is R1 . 62 63config NIOS2_HW_MUL_SUPPORT 64 bool "Enable MUL instruction" 65 help 66 Set to true if you configured the Nios II to include the MUL 67 instruction. This will enable the -mhw-mul compiler flag. 68 69config NIOS2_HW_MULX_SUPPORT 70 bool "Enable MULX instruction" 71 help 72 Set to true if you configured the Nios II to include the MULX 73 instruction. Enables the -mhw-mulx compiler flag. 74 75config NIOS2_HW_DIV_SUPPORT 76 bool "Enable DIV instruction" 77 help 78 Set to true if you configured the Nios II to include the DIV 79 instruction. Enables the -mhw-div compiler flag. 80 81config NIOS2_BMX_SUPPORT 82 bool "Enable BMX instructions" 83 depends on NIOS2_ARCH_REVISION = 2 84 help 85 Set to true if you configured the Nios II R2 to include 86 the BMX Bit Manipulation Extension instructions. Enables 87 the -mbmx compiler flag. 88 89config NIOS2_CDX_SUPPORT 90 bool "Enable CDX instructions" 91 depends on NIOS2_ARCH_REVISION = 2 92 help 93 Set to true if you configured the Nios II R2 to include 94 the CDX Bit Manipulation Extension instructions. Enables 95 the -mcdx compiler flag. 96 97config NIOS2_FPU_SUPPORT 98 bool "Custom floating point instr support" 99 help 100 Enables the -mcustom-fpu-cfg=60-1 compiler flag. 101 102config NIOS2_CI_SWAB_SUPPORT 103 bool "Byteswap custom instruction" 104 help 105 Use the byteswap (endian converter) Nios II custom instruction provided 106 by Altera and which can be enabled in QSYS builder. This accelerates 107 endian conversions in the kernel (e.g. ntohs). 108 109config NIOS2_CI_SWAB_NO 110 int "Byteswap custom instruction number" if NIOS2_CI_SWAB_SUPPORT 111 default 0 112 help 113 Number of the instruction as configured in QSYS Builder. 114 115comment "Cache settings" 116 117config CUSTOM_CACHE_SETTINGS 118 bool "Custom cache settings" 119 help 120 This option allows you to tweak the cache settings used during early 121 boot (where the information from device tree is not yet available). 122 There should be no reason to change these values. Linux will work 123 perfectly fine, even if the Nios II is configured with smaller caches. 124 125 Say N here unless you know what you are doing. 126 127config NIOS2_DCACHE_SIZE 128 hex "D-Cache size" if CUSTOM_CACHE_SETTINGS 129 range 0x200 0x10000 130 default "0x800" 131 help 132 Maximum possible data cache size. 133 134config NIOS2_DCACHE_LINE_SIZE 135 hex "D-Cache line size" if CUSTOM_CACHE_SETTINGS 136 range 0x10 0x20 137 default "0x20" 138 help 139 Minimum possible data cache line size. 140 141config NIOS2_ICACHE_SIZE 142 hex "I-Cache size" if CUSTOM_CACHE_SETTINGS 143 range 0x200 0x10000 144 default "0x1000" 145 help 146 Maximum possible instruction cache size. 147 148endmenu