idt77105.h (3840B)
1/* SPDX-License-Identifier: GPL-2.0 */ 2/* drivers/atm/idt77105.h - IDT77105 (PHY) declarations */ 3 4/* Written 1999 by Greg Banks, NEC Australia <gnb@linuxfan.com>. Based on suni.h */ 5 6 7#ifndef DRIVER_ATM_IDT77105_H 8#define DRIVER_ATM_IDT77105_H 9 10#include <linux/atmdev.h> 11#include <linux/atmioc.h> 12 13 14/* IDT77105 registers */ 15 16#define IDT77105_MCR 0x0 /* Master Control Register */ 17#define IDT77105_ISTAT 0x1 /* Interrupt Status */ 18#define IDT77105_DIAG 0x2 /* Diagnostic Control */ 19#define IDT77105_LEDHEC 0x3 /* LED Driver & HEC Status/Control */ 20#define IDT77105_CTRLO 0x4 /* Low Byte Counter Register */ 21#define IDT77105_CTRHI 0x5 /* High Byte Counter Register */ 22#define IDT77105_CTRSEL 0x6 /* Counter Register Read Select */ 23 24/* IDT77105 register values */ 25 26/* MCR */ 27#define IDT77105_MCR_UPLO 0x80 /* R/W, User Prog'le Output Latch */ 28#define IDT77105_MCR_DREC 0x40 /* R/W, Discard Receive Error Cells */ 29#define IDT77105_MCR_ECEIO 0x20 /* R/W, Enable Cell Error Interrupts 30 * Only */ 31#define IDT77105_MCR_TDPC 0x10 /* R/W, Transmit Data Parity Check */ 32#define IDT77105_MCR_DRIC 0x08 /* R/W, Discard Received Idle Cells */ 33#define IDT77105_MCR_HALTTX 0x04 /* R/W, Halt Tx */ 34#define IDT77105_MCR_UMODE 0x02 /* R/W, Utopia (cell/byte) Mode */ 35#define IDT77105_MCR_EIP 0x01 /* R/W, Enable Interrupt Pin */ 36 37/* ISTAT */ 38#define IDT77105_ISTAT_GOODSIG 0x40 /* R, Good Signal Bit */ 39#define IDT77105_ISTAT_HECERR 0x20 /* sticky, HEC Error*/ 40#define IDT77105_ISTAT_SCR 0x10 /* sticky, Short Cell Received */ 41#define IDT77105_ISTAT_TPE 0x08 /* sticky, Transmit Parity Error */ 42#define IDT77105_ISTAT_RSCC 0x04 /* sticky, Rx Signal Condition Change */ 43#define IDT77105_ISTAT_RSE 0x02 /* sticky, Rx Symbol Error */ 44#define IDT77105_ISTAT_RFO 0x01 /* sticky, Rx FIFO Overrun */ 45 46/* DIAG */ 47#define IDT77105_DIAG_FTD 0x80 /* R/W, Force TxClav deassert */ 48#define IDT77105_DIAG_ROS 0x40 /* R/W, RxClav operation select */ 49#define IDT77105_DIAG_MPCS 0x20 /* R/W, Multi-PHY config'n select */ 50#define IDT77105_DIAG_RFLUSH 0x10 /* R/W, clear receive FIFO */ 51#define IDT77105_DIAG_ITPE 0x08 /* R/W, Insert Tx payload error */ 52#define IDT77105_DIAG_ITHE 0x04 /* R/W, Insert Tx HEC error */ 53#define IDT77105_DIAG_UMODE 0x02 /* R/W, Utopia (cell/byte) Mode */ 54#define IDT77105_DIAG_LCMASK 0x03 /* R/W, Loopback Control */ 55 56#define IDT77105_DIAG_LC_NORMAL 0x00 /* Receive from network */ 57#define IDT77105_DIAG_LC_PHY_LOOPBACK 0x02 58#define IDT77105_DIAG_LC_LINE_LOOPBACK 0x03 59 60/* LEDHEC */ 61#define IDT77105_LEDHEC_DRHC 0x40 /* R/W, Disable Rx HEC check */ 62#define IDT77105_LEDHEC_DTHC 0x20 /* R/W, Disable Tx HEC calculation */ 63#define IDT77105_LEDHEC_RPWMASK 0x18 /* R/W, RxRef pulse width select */ 64#define IDT77105_LEDHEC_TFS 0x04 /* R, Tx FIFO Status (1=empty) */ 65#define IDT77105_LEDHEC_TLS 0x02 /* R, Tx LED Status (1=lit) */ 66#define IDT77105_LEDHEC_RLS 0x01 /* R, Rx LED Status (1=lit) */ 67 68#define IDT77105_LEDHEC_RPW_1 0x00 /* RxRef active for 1 RxClk cycle */ 69#define IDT77105_LEDHEC_RPW_2 0x08 /* RxRef active for 2 RxClk cycle */ 70#define IDT77105_LEDHEC_RPW_4 0x10 /* RxRef active for 4 RxClk cycle */ 71#define IDT77105_LEDHEC_RPW_8 0x18 /* RxRef active for 8 RxClk cycle */ 72 73/* CTRSEL */ 74#define IDT77105_CTRSEL_SEC 0x08 /* W, Symbol Error Counter */ 75#define IDT77105_CTRSEL_TCC 0x04 /* W, Tx Cell Counter */ 76#define IDT77105_CTRSEL_RCC 0x02 /* W, Rx Cell Counter */ 77#define IDT77105_CTRSEL_RHEC 0x01 /* W, Rx HEC Error Counter */ 78 79#ifdef __KERNEL__ 80int idt77105_init(struct atm_dev *dev); 81#endif 82 83/* 84 * Tunable parameters 85 */ 86 87/* Time between samples of the hardware cell counters. Should be <= 1 sec */ 88#define IDT77105_STATS_TIMER_PERIOD (HZ) 89/* Time between checks to see if the signal has been found again */ 90#define IDT77105_RESTART_TIMER_PERIOD (5 * HZ) 91 92#endif