Kconfig (4623B)
1# SPDX-License-Identifier: GPL-2.0-only 2menuconfig LEDS_TRIGGERS 3 bool "LED Trigger support" 4 depends on LEDS_CLASS 5 help 6 This option enables trigger support for the leds class. 7 These triggers allow kernel events to drive the LEDs and can 8 be configured via sysfs. If unsure, say Y. 9 10if LEDS_TRIGGERS 11 12config LEDS_TRIGGER_TIMER 13 tristate "LED Timer Trigger" 14 help 15 This allows LEDs to be controlled by a programmable timer 16 via sysfs. Some LED hardware can be programmed to start 17 blinking the LED without any further software interaction. 18 For more details read Documentation/leds/leds-class.rst. 19 20 If unsure, say Y. 21 22config LEDS_TRIGGER_ONESHOT 23 tristate "LED One-shot Trigger" 24 help 25 This allows LEDs to blink in one-shot pulses with parameters 26 controlled via sysfs. It's useful to notify the user on 27 sporadic events, when there are no clear begin and end trap points, 28 or on dense events, where this blinks the LED at constant rate if 29 rearmed continuously. 30 31 It also shows how to use the led_blink_set_oneshot() function. 32 33 If unsure, say Y. 34 35config LEDS_TRIGGER_DISK 36 bool "LED Disk Trigger" 37 depends on ATA 38 help 39 This allows LEDs to be controlled by disk activity. 40 If unsure, say Y. 41 42config LEDS_TRIGGER_MTD 43 bool "LED MTD (NAND/NOR) Trigger" 44 depends on MTD 45 help 46 This allows LEDs to be controlled by MTD activity. 47 If unsure, say N. 48 49config LEDS_TRIGGER_HEARTBEAT 50 tristate "LED Heartbeat Trigger" 51 help 52 This allows LEDs to be controlled by a CPU load average. 53 The flash frequency is a hyperbolic function of the 1-minute 54 load average. 55 If unsure, say Y. 56 57config LEDS_TRIGGER_BACKLIGHT 58 tristate "LED backlight Trigger" 59 help 60 This allows LEDs to be controlled as a backlight device: they 61 turn off and on when the display is blanked and unblanked. 62 63 If unsure, say N. 64 65config LEDS_TRIGGER_CPU 66 bool "LED CPU Trigger" 67 depends on !PREEMPT_RT 68 help 69 This allows LEDs to be controlled by active CPUs. This shows 70 the active CPUs across an array of LEDs so you can see which 71 CPUs are active on the system at any given moment. 72 73 If unsure, say N. 74 75config LEDS_TRIGGER_ACTIVITY 76 tristate "LED activity Trigger" 77 help 78 This allows LEDs to be controlled by an immediate CPU usage. 79 The flash frequency and duty cycle varies from faint flashes to 80 intense brightness depending on the instant CPU load. 81 If unsure, say N. 82 83config LEDS_TRIGGER_GPIO 84 tristate "LED GPIO Trigger" 85 depends on GPIOLIB || COMPILE_TEST 86 help 87 This allows LEDs to be controlled by gpio events. It's good 88 when using gpios as switches and triggering the needed LEDs 89 from there. One use case is n810's keypad LEDs that could 90 be triggered by this trigger when user slides up to show 91 keypad. 92 93 If unsure, say N. 94 95config LEDS_TRIGGER_DEFAULT_ON 96 tristate "LED Default ON Trigger" 97 help 98 This allows LEDs to be initialised in the ON state. 99 If unsure, say Y. 100 101comment "iptables trigger is under Netfilter config (LED target)" 102 depends on LEDS_TRIGGERS 103 104config LEDS_TRIGGER_TRANSIENT 105 tristate "LED Transient Trigger" 106 help 107 This allows one time activation of a transient state on 108 GPIO/PWM based hardware. 109 If unsure, say Y. 110 111config LEDS_TRIGGER_CAMERA 112 tristate "LED Camera Flash/Torch Trigger" 113 help 114 This allows LEDs to be controlled as a camera flash/torch device. 115 This enables direct flash/torch on/off by the driver, kernel space. 116 If unsure, say Y. 117 118config LEDS_TRIGGER_PANIC 119 bool "LED Panic Trigger" 120 help 121 This allows LEDs to be configured to blink on a kernel panic. 122 Enabling this option will allow to mark certain LEDs as panic indicators, 123 allowing to blink them on a kernel panic, even if they are set to 124 a different trigger. 125 If unsure, say Y. 126 127config LEDS_TRIGGER_NETDEV 128 tristate "LED Netdev Trigger" 129 depends on NET 130 help 131 This allows LEDs to be controlled by network device activity. 132 If unsure, say Y. 133 134config LEDS_TRIGGER_PATTERN 135 tristate "LED Pattern Trigger" 136 help 137 This allows LEDs to be controlled by a software or hardware pattern 138 which is a series of tuples, of brightness and duration (ms). 139 If unsure, say N 140 141config LEDS_TRIGGER_AUDIO 142 tristate "Audio Mute LED Trigger" 143 help 144 This allows LEDs to be controlled by audio drivers for following 145 the audio mute and mic-mute changes. 146 If unsure, say N 147 148config LEDS_TRIGGER_TTY 149 tristate "LED Trigger for TTY devices" 150 depends on TTY 151 help 152 This allows LEDs to be controlled by activity on ttys which includes 153 serial devices like /dev/ttyS0. 154 155 When build as a module this driver will be called ledtrig-tty. 156 157endif # LEDS_TRIGGERS