ene_ir.h (8056B)
1/* SPDX-License-Identifier: GPL-2.0-or-later */ 2/* 3 * driver for ENE KB3926 B/C/D/E/F CIR (also known as ENE0XXX) 4 * 5 * Copyright (C) 2010 Maxim Levitsky <maximlevitsky@gmail.com> 6 */ 7#include <linux/spinlock.h> 8 9 10/* hardware address */ 11#define ENE_STATUS 0 /* hardware status - unused */ 12#define ENE_ADDR_HI 1 /* hi byte of register address */ 13#define ENE_ADDR_LO 2 /* low byte of register address */ 14#define ENE_IO 3 /* read/write window */ 15#define ENE_IO_SIZE 4 16 17/* 8 bytes of samples, divided in 2 packets*/ 18#define ENE_FW_SAMPLE_BUFFER 0xF8F0 /* sample buffer */ 19#define ENE_FW_SAMPLE_SPACE 0x80 /* sample is space */ 20#define ENE_FW_PACKET_SIZE 4 21 22/* first firmware flag register */ 23#define ENE_FW1 0xF8F8 /* flagr */ 24#define ENE_FW1_ENABLE 0x01 /* enable fw processing */ 25#define ENE_FW1_TXIRQ 0x02 /* TX interrupt pending */ 26#define ENE_FW1_HAS_EXTRA_BUF 0x04 /* fw uses extra buffer*/ 27#define ENE_FW1_EXTRA_BUF_HND 0x08 /* extra buffer handshake bit*/ 28#define ENE_FW1_LED_ON 0x10 /* turn on a led */ 29 30#define ENE_FW1_WPATTERN 0x20 /* enable wake pattern */ 31#define ENE_FW1_WAKE 0x40 /* enable wake from S3 */ 32#define ENE_FW1_IRQ 0x80 /* enable interrupt */ 33 34/* second firmware flag register */ 35#define ENE_FW2 0xF8F9 /* flagw */ 36#define ENE_FW2_BUF_WPTR 0x01 /* which half of the buffer to read */ 37#define ENE_FW2_RXIRQ 0x04 /* RX IRQ pending*/ 38#define ENE_FW2_GP0A 0x08 /* Use GPIO0A for demodulated input */ 39#define ENE_FW2_EMMITER1_CONN 0x10 /* TX emmiter 1 connected */ 40#define ENE_FW2_EMMITER2_CONN 0x20 /* TX emmiter 2 connected */ 41 42#define ENE_FW2_FAN_INPUT 0x40 /* fan input used for demodulated data*/ 43#define ENE_FW2_LEARNING 0x80 /* hardware supports learning and TX */ 44 45/* firmware RX pointer for new style buffer */ 46#define ENE_FW_RX_POINTER 0xF8FA 47 48/* high parts of samples for fan input (8 samples)*/ 49#define ENE_FW_SMPL_BUF_FAN 0xF8FB 50#define ENE_FW_SMPL_BUF_FAN_PLS 0x8000 /* combined sample is pulse */ 51#define ENE_FW_SMPL_BUF_FAN_MSK 0x0FFF /* combined sample maximum value */ 52#define ENE_FW_SAMPLE_PERIOD_FAN 61 /* fan input has fixed sample period */ 53 54/* transmitter ports */ 55#define ENE_GPIOFS1 0xFC01 56#define ENE_GPIOFS1_GPIO0D 0x20 /* enable tx output on GPIO0D */ 57#define ENE_GPIOFS8 0xFC08 58#define ENE_GPIOFS8_GPIO41 0x02 /* enable tx output on GPIO40 */ 59 60/* IRQ registers block (for revision B) */ 61#define ENEB_IRQ 0xFD09 /* IRQ number */ 62#define ENEB_IRQ_UNK1 0xFD17 /* unknown setting = 1 */ 63#define ENEB_IRQ_STATUS 0xFD80 /* irq status */ 64#define ENEB_IRQ_STATUS_IR 0x20 /* IR irq */ 65 66/* fan as input settings */ 67#define ENE_FAN_AS_IN1 0xFE30 /* fan init reg 1 */ 68#define ENE_FAN_AS_IN1_EN 0xCD 69#define ENE_FAN_AS_IN2 0xFE31 /* fan init reg 2 */ 70#define ENE_FAN_AS_IN2_EN 0x03 71 72/* IRQ registers block (for revision C,D) */ 73#define ENE_IRQ 0xFE9B /* new irq settings register */ 74#define ENE_IRQ_MASK 0x0F /* irq number mask */ 75#define ENE_IRQ_UNK_EN 0x10 /* always enabled */ 76#define ENE_IRQ_STATUS 0x20 /* irq status and ACK */ 77 78/* CIR Config register #1 */ 79#define ENE_CIRCFG 0xFEC0 80#define ENE_CIRCFG_RX_EN 0x01 /* RX enable */ 81#define ENE_CIRCFG_RX_IRQ 0x02 /* Enable hardware interrupt */ 82#define ENE_CIRCFG_REV_POL 0x04 /* Input polarity reversed */ 83#define ENE_CIRCFG_CARR_DEMOD 0x08 /* Enable carrier demodulator */ 84 85#define ENE_CIRCFG_TX_EN 0x10 /* TX enable */ 86#define ENE_CIRCFG_TX_IRQ 0x20 /* Send interrupt on TX done */ 87#define ENE_CIRCFG_TX_POL_REV 0x40 /* TX polarity reversed */ 88#define ENE_CIRCFG_TX_CARR 0x80 /* send TX carrier or not */ 89 90/* CIR config register #2 */ 91#define ENE_CIRCFG2 0xFEC1 92#define ENE_CIRCFG2_RLC 0x00 93#define ENE_CIRCFG2_RC5 0x01 94#define ENE_CIRCFG2_RC6 0x02 95#define ENE_CIRCFG2_NEC 0x03 96#define ENE_CIRCFG2_CARR_DETECT 0x10 /* Enable carrier detection */ 97#define ENE_CIRCFG2_GPIO0A 0x20 /* Use GPIO0A instead of GPIO40 for input */ 98#define ENE_CIRCFG2_FAST_SAMPL1 0x40 /* Fast leading pulse detection for RC6 */ 99#define ENE_CIRCFG2_FAST_SAMPL2 0x80 /* Fast data detection for RC6 */ 100 101/* Knobs for protocol decoding - will document when/if will use them */ 102#define ENE_CIRPF 0xFEC2 103#define ENE_CIRHIGH 0xFEC3 104#define ENE_CIRBIT 0xFEC4 105#define ENE_CIRSTART 0xFEC5 106#define ENE_CIRSTART2 0xFEC6 107 108/* Actual register which contains RLC RX data - read by firmware */ 109#define ENE_CIRDAT_IN 0xFEC7 110 111 112/* RLC configuration - sample period (1us resolution) + idle mode */ 113#define ENE_CIRRLC_CFG 0xFEC8 114#define ENE_CIRRLC_CFG_OVERFLOW 0x80 /* interrupt on overflows if set */ 115#define ENE_DEFAULT_SAMPLE_PERIOD 50 116 117/* Two byte RLC TX buffer */ 118#define ENE_CIRRLC_OUT0 0xFEC9 119#define ENE_CIRRLC_OUT1 0xFECA 120#define ENE_CIRRLC_OUT_PULSE 0x80 /* Transmitted sample is pulse */ 121#define ENE_CIRRLC_OUT_MASK 0x7F 122 123 124/* Carrier detect setting 125 * Low nibble - number of carrier pulses to average 126 * High nibble - number of initial carrier pulses to discard 127 */ 128#define ENE_CIRCAR_PULS 0xFECB 129 130/* detected RX carrier period (resolution: 500 ns) */ 131#define ENE_CIRCAR_PRD 0xFECC 132#define ENE_CIRCAR_PRD_VALID 0x80 /* data valid content valid */ 133 134/* detected RX carrier pulse width (resolution: 500 ns) */ 135#define ENE_CIRCAR_HPRD 0xFECD 136 137/* TX period (resolution: 500 ns, minimum 2)*/ 138#define ENE_CIRMOD_PRD 0xFECE 139#define ENE_CIRMOD_PRD_POL 0x80 /* TX carrier polarity*/ 140 141#define ENE_CIRMOD_PRD_MAX 0x7F /* 15.87 kHz */ 142#define ENE_CIRMOD_PRD_MIN 0x02 /* 1 Mhz */ 143 144/* TX pulse width (resolution: 500 ns)*/ 145#define ENE_CIRMOD_HPRD 0xFECF 146 147/* Hardware versions */ 148#define ENE_ECHV 0xFF00 /* hardware revision */ 149#define ENE_PLLFRH 0xFF16 150#define ENE_PLLFRL 0xFF17 151#define ENE_DEFAULT_PLL_FREQ 1000 152 153#define ENE_ECSTS 0xFF1D 154#define ENE_ECSTS_RSRVD 0x04 155 156#define ENE_ECVER_MAJOR 0xFF1E /* chip version */ 157#define ENE_ECVER_MINOR 0xFF1F 158#define ENE_HW_VER_OLD 0xFD00 159 160/******************************************************************************/ 161 162#define ENE_DRIVER_NAME "ene_ir" 163 164#define ENE_IRQ_RX 1 165#define ENE_IRQ_TX 2 166 167#define ENE_HW_B 1 /* 3926B */ 168#define ENE_HW_C 2 /* 3926C */ 169#define ENE_HW_D 3 /* 3926D or later */ 170 171#define __dbg(level, format, ...) \ 172do { \ 173 if (debug >= level) \ 174 pr_info(format "\n", ## __VA_ARGS__); \ 175} while (0) 176 177#define dbg(format, ...) __dbg(1, format, ## __VA_ARGS__) 178#define dbg_verbose(format, ...) __dbg(2, format, ## __VA_ARGS__) 179#define dbg_regs(format, ...) __dbg(3, format, ## __VA_ARGS__) 180 181struct ene_device { 182 struct pnp_dev *pnp_dev; 183 struct rc_dev *rdev; 184 185 /* hw IO settings */ 186 long hw_io; 187 int irq; 188 spinlock_t hw_lock; 189 190 /* HW features */ 191 int hw_revision; /* hardware revision */ 192 bool hw_use_gpio_0a; /* gpio0a is demodulated input*/ 193 bool hw_extra_buffer; /* hardware has 'extra buffer' */ 194 bool hw_fan_input; /* fan input is IR data source */ 195 bool hw_learning_and_tx_capable; /* learning & tx capable */ 196 int pll_freq; 197 int buffer_len; 198 199 /* Extra RX buffer location */ 200 int extra_buf1_address; 201 int extra_buf1_len; 202 int extra_buf2_address; 203 int extra_buf2_len; 204 205 /* HW state*/ 206 int r_pointer; /* pointer to next sample to read */ 207 int w_pointer; /* pointer to next sample hw will write */ 208 bool rx_fan_input_inuse; /* is fan input in use for rx*/ 209 int tx_reg; /* current reg used for TX */ 210 u8 saved_conf1; /* saved FEC0 reg */ 211 unsigned int tx_sample; /* current sample for TX */ 212 bool tx_sample_pulse; /* current sample is pulse */ 213 214 /* TX buffer */ 215 unsigned *tx_buffer; /* input samples buffer*/ 216 int tx_pos; /* position in that buffer */ 217 int tx_len; /* current len of tx buffer */ 218 int tx_done; /* done transmitting */ 219 /* one more sample pending*/ 220 struct completion tx_complete; /* TX completion */ 221 struct timer_list tx_sim_timer; 222 223 /* TX settings */ 224 int tx_period; 225 int tx_duty_cycle; 226 int transmitter_mask; 227 228 /* RX settings */ 229 bool learning_mode_enabled; /* learning input enabled */ 230 bool carrier_detect_enabled; /* carrier detect enabled */ 231 int rx_period_adjust; 232 bool rx_enabled; 233}; 234 235static int ene_irq_status(struct ene_device *dev); 236static void ene_rx_read_hw_pointer(struct ene_device *dev);