Kconfig (8426B)
1# SPDX-License-Identifier: GPL-2.0-only 2# 3# Memory devices 4# 5 6menuconfig MEMORY 7 bool "Memory Controller drivers" 8 help 9 This option allows to enable specific memory controller drivers, 10 useful mostly on embedded systems. These could be controllers 11 for DRAM (SDR, DDR), ROM, SRAM and others. The drivers features 12 vary from memory tuning and frequency scaling to enabling 13 access to attached peripherals through memory bus. 14 15if MEMORY 16 17config DDR 18 bool 19 help 20 Data from JEDEC specs for DDR SDRAM memories, 21 particularly the AC timing parameters and addressing 22 information. This data is useful for drivers handling 23 DDR SDRAM controllers. 24 25config ARM_PL172_MPMC 26 tristate "ARM PL172 MPMC driver" 27 depends on ARM_AMBA && OF 28 help 29 This selects the ARM PrimeCell PL172 MultiPort Memory Controller. 30 If you have an embedded system with an AMBA bus and a PL172 31 controller, say Y or M here. 32 33config ATMEL_SDRAMC 34 bool "Atmel (Multi-port DDR-)SDRAM Controller" 35 default y if ARCH_AT91 36 depends on ARCH_AT91 || COMPILE_TEST 37 depends on OF 38 help 39 This driver is for Atmel SDRAM Controller or Atmel Multi-port 40 DDR-SDRAM Controller available on Atmel AT91SAM9 and SAMA5 SoCs. 41 Starting with the at91sam9g45, this controller supports SDR, DDR and 42 LP-DDR memories. 43 44config ATMEL_EBI 45 bool "Atmel EBI driver" 46 default y if ARCH_AT91 47 depends on ARCH_AT91 || COMPILE_TEST 48 depends on OF 49 select MFD_SYSCON 50 select MFD_ATMEL_SMC 51 help 52 Driver for Atmel EBI controller. 53 Used to configure the EBI (external bus interface) when the device- 54 tree is used. This bus supports NANDs, external ethernet controller, 55 SRAMs, ATA devices, etc. 56 57config BRCMSTB_DPFE 58 tristate "Broadcom STB DPFE driver" 59 default ARCH_BRCMSTB 60 depends on ARCH_BRCMSTB || COMPILE_TEST 61 help 62 This driver provides access to the DPFE interface of Broadcom 63 STB SoCs. The firmware running on the DCPU inside the DDR PHY can 64 provide current information about the system's RAM, for instance 65 the DRAM refresh rate. This can be used as an indirect indicator 66 for the DRAM's temperature. Slower refresh rate means cooler RAM, 67 higher refresh rate means hotter RAM. 68 69config BT1_L2_CTL 70 bool "Baikal-T1 CM2 L2-RAM Cache Control Block" 71 depends on MIPS_BAIKAL_T1 || COMPILE_TEST 72 select MFD_SYSCON 73 help 74 Baikal-T1 CPU is based on the MIPS P5600 Warrior IP-core. The CPU 75 resides Coherency Manager v2 with embedded 1MB L2-cache. It's 76 possible to tune the L2 cache performance up by setting the data, 77 tags and way-select latencies of RAM access. This driver provides a 78 dt properties-based and sysfs interface for it. 79 80config TI_AEMIF 81 tristate "Texas Instruments AEMIF driver" 82 depends on ARCH_DAVINCI || ARCH_KEYSTONE || COMPILE_TEST 83 depends on OF 84 help 85 This driver is for the AEMIF module available in Texas Instruments 86 SoCs. AEMIF stands for Asynchronous External Memory Interface and 87 is intended to provide a glue-less interface to a variety of 88 asynchronuous memory devices like ASRAM, NOR and NAND memory. A total 89 of 256M bytes of any of these memories can be accessed at a given 90 time via four chip selects with 64M byte access per chip select. 91 92config TI_EMIF 93 tristate "Texas Instruments EMIF driver" 94 depends on ARCH_OMAP2PLUS || COMPILE_TEST 95 select DDR 96 help 97 This driver is for the EMIF module available in Texas Instruments 98 SoCs. EMIF is an SDRAM controller that, based on its revision, 99 supports one or more of DDR2, DDR3, and LPDDR2 SDRAM protocols. 100 This driver takes care of only LPDDR2 memories presently. The 101 functions of the driver includes re-configuring AC timing 102 parameters and other settings during frequency, voltage and 103 temperature changes 104 105config OMAP_GPMC 106 tristate "Texas Instruments OMAP SoC GPMC driver" 107 depends on OF_ADDRESS 108 depends on ARCH_OMAP2PLUS || ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST 109 select GPIOLIB 110 help 111 This driver is for the General Purpose Memory Controller (GPMC) 112 present on Texas Instruments SoCs (e.g. OMAP2+). GPMC allows 113 interfacing to a variety of asynchronous as well as synchronous 114 memory drives like NOR, NAND, OneNAND, SRAM. 115 116config OMAP_GPMC_DEBUG 117 bool "Enable GPMC debug output and skip reset of GPMC during init" 118 depends on OMAP_GPMC 119 help 120 Enables verbose debugging mostly to decode the bootloader provided 121 timings. To preserve the bootloader provided timings, the reset 122 of GPMC is skipped during init. Enable this during development to 123 configure devices connected to the GPMC bus. 124 125 NOTE: In addition to matching the register setup with the bootloader 126 you also need to match the GPMC FCLK frequency used by the 127 bootloader or else the GPMC timings won't be identical with the 128 bootloader timings. 129 130config TI_EMIF_SRAM 131 tristate "Texas Instruments EMIF SRAM driver" 132 depends on SOC_AM33XX || SOC_AM43XX || (ARM && CPU_V7 && COMPILE_TEST) 133 depends on SRAM 134 help 135 This driver is for the EMIF module available on Texas Instruments 136 AM33XX and AM43XX SoCs and is required for PM. Certain parts of 137 the EMIF PM code must run from on-chip SRAM late in the suspend 138 sequence so this driver provides several relocatable PM functions 139 for the SoC PM code to use. 140 141config FPGA_DFL_EMIF 142 tristate "FPGA DFL EMIF Driver" 143 depends on FPGA_DFL && HAS_IOMEM 144 help 145 This driver is for the EMIF private feature implemented under 146 FPGA Device Feature List (DFL) framework. It is used to expose 147 memory interface status information as well as memory clearing 148 control. 149 150config MVEBU_DEVBUS 151 bool "Marvell EBU Device Bus Controller" 152 default y if PLAT_ORION 153 depends on PLAT_ORION || COMPILE_TEST 154 depends on OF 155 help 156 This driver is for the Device Bus controller available in some 157 Marvell EBU SoCs such as Discovery (mv78xx0), Orion (88f5xxx) and 158 Armada 370 and Armada XP. This controller allows to handle flash 159 devices such as NOR, NAND, SRAM, and FPGA. 160 161config FSL_CORENET_CF 162 tristate "Freescale CoreNet Error Reporting" 163 depends on FSL_SOC_BOOKE || COMPILE_TEST 164 help 165 Say Y for reporting of errors from the Freescale CoreNet 166 Coherency Fabric. Errors reported include accesses to 167 physical addresses that mapped by no local access window 168 (LAW) or an invalid LAW, as well as bad cache state that 169 represents a coherency violation. 170 171config FSL_IFC 172 bool "Freescale IFC driver" if COMPILE_TEST 173 depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A || COMPILE_TEST 174 depends on HAS_IOMEM 175 176config JZ4780_NEMC 177 bool "Ingenic JZ4780 SoC NEMC driver" 178 depends on MIPS || COMPILE_TEST 179 depends on HAS_IOMEM && OF 180 help 181 This driver is for the NAND/External Memory Controller (NEMC) in 182 the Ingenic JZ4780. This controller is used to handle external 183 memory devices such as NAND and SRAM. 184 185config MTK_SMI 186 tristate "MediaTek SoC Memory Controller driver" if COMPILE_TEST 187 depends on ARCH_MEDIATEK || COMPILE_TEST 188 help 189 This driver is for the Memory Controller module in MediaTek SoCs, 190 mainly help enable/disable iommu and control the power domain and 191 clocks for each local arbiter. 192 193config DA8XX_DDRCTL 194 bool "Texas Instruments da8xx DDR2/mDDR driver" 195 depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST 196 help 197 This driver is for the DDR2/mDDR Memory Controller present on 198 Texas Instruments da8xx SoCs. It's used to tweak various memory 199 controller configuration options. 200 201config PL353_SMC 202 tristate "ARM PL35X Static Memory Controller(SMC) driver" 203 default y if ARM 204 depends on ARM || COMPILE_TEST 205 depends on ARM_AMBA 206 help 207 This driver is for the ARM PL351/PL353 Static Memory 208 Controller(SMC) module. 209 210config RENESAS_RPCIF 211 tristate "Renesas RPC-IF driver" 212 depends on ARCH_RENESAS || COMPILE_TEST 213 select REGMAP_MMIO 214 select RESET_CONTROLLER 215 help 216 This supports Renesas R-Car Gen3 or RZ/G2 RPC-IF which provides 217 either SPI host or HyperFlash. You'll have to select individual 218 components under the corresponding menu. 219 220config STM32_FMC2_EBI 221 tristate "Support for FMC2 External Bus Interface on STM32MP SoCs" 222 depends on MACH_STM32MP157 || COMPILE_TEST 223 select MFD_SYSCON 224 help 225 Select this option to enable the STM32 FMC2 External Bus Interface 226 controller. This driver configures the transactions with external 227 devices (like SRAM, ethernet adapters, FPGAs, LCD displays, ...) on 228 SOCs containing the FMC2 External Bus Interface. 229 230source "drivers/memory/samsung/Kconfig" 231source "drivers/memory/tegra/Kconfig" 232 233endif