r592.h (6210B)
1/* SPDX-License-Identifier: GPL-2.0-only */ 2/* 3 * Copyright (C) 2010 - Maxim Levitsky 4 * driver for Ricoh memstick readers 5 */ 6 7#ifndef R592_H 8 9#include <linux/memstick.h> 10#include <linux/spinlock.h> 11#include <linux/interrupt.h> 12#include <linux/workqueue.h> 13#include <linux/kfifo.h> 14#include <linux/ctype.h> 15 16/* write to this reg (number,len) triggers TPC execution */ 17#define R592_TPC_EXEC 0x00 18#define R592_TPC_EXEC_LEN_SHIFT 16 /* Bits 16..25 are TPC len */ 19#define R592_TPC_EXEC_BIG_FIFO (1 << 26) /* If bit 26 is set, large fifo is used (reg 48) */ 20#define R592_TPC_EXEC_TPC_SHIFT 28 /* Bits 28..31 are the TPC number */ 21 22 23/* Window for small TPC fifo (big endian)*/ 24/* reads and writes always are done in 8 byte chunks */ 25/* Not used in driver, because large fifo does better job */ 26#define R592_SFIFO 0x08 27 28 29/* Status register (ms int, small fifo, IO)*/ 30#define R592_STATUS 0x10 31 /* Parallel INT bits */ 32#define R592_STATUS_P_CMDNACK (1 << 16) /* INT reg: NACK (parallel mode) */ 33#define R592_STATUS_P_BREQ (1 << 17) /* INT reg: card ready (parallel mode)*/ 34#define R592_STATUS_P_INTERR (1 << 18) /* INT reg: int error (parallel mode)*/ 35#define R592_STATUS_P_CED (1 << 19) /* INT reg: command done (parallel mode) */ 36 37 /* Fifo status */ 38#define R592_STATUS_SFIFO_FULL (1 << 20) /* Small Fifo almost full (last chunk is written) */ 39#define R592_STATUS_SFIFO_EMPTY (1 << 21) /* Small Fifo empty */ 40 41 /* Error detection via CRC */ 42#define R592_STATUS_SEND_ERR (1 << 24) /* Send failed */ 43#define R592_STATUS_RECV_ERR (1 << 25) /* Receive failed */ 44 45 /* Card state */ 46#define R592_STATUS_RDY (1 << 28) /* RDY signal received */ 47#define R592_STATUS_CED (1 << 29) /* INT: Command done (serial mode)*/ 48#define R592_STATUS_SFIFO_INPUT (1 << 30) /* Small fifo received data*/ 49 50#define R592_SFIFO_SIZE 32 /* total size of small fifo is 32 bytes */ 51#define R592_SFIFO_PACKET 8 /* packet size of small fifo */ 52 53/* IO control */ 54#define R592_IO 0x18 55#define R592_IO_16 (1 << 16) /* Set by default, can be cleared */ 56#define R592_IO_18 (1 << 18) /* Set by default, can be cleared */ 57#define R592_IO_SERIAL1 (1 << 20) /* Set by default, can be cleared, (cleared on parallel) */ 58#define R592_IO_22 (1 << 22) /* Set by default, can be cleared */ 59#define R592_IO_DIRECTION (1 << 24) /* TPC direction (1 write 0 read) */ 60#define R592_IO_26 (1 << 26) /* Set by default, can be cleared */ 61#define R592_IO_SERIAL2 (1 << 30) /* Set by default, can be cleared (cleared on parallel), serial doesn't work if unset */ 62#define R592_IO_RESET (1 << 31) /* Reset, sets defaults*/ 63 64 65/* Turns hardware on/off */ 66#define R592_POWER 0x20 /* bits 0-7 writeable */ 67#define R592_POWER_0 (1 << 0) /* set on start, cleared on stop - must be set*/ 68#define R592_POWER_1 (1 << 1) /* set on start, cleared on stop - must be set*/ 69#define R592_POWER_3 (1 << 3) /* must be clear */ 70#define R592_POWER_20 (1 << 5) /* set before switch to parallel */ 71 72/* IO mode*/ 73#define R592_IO_MODE 0x24 74#define R592_IO_MODE_SERIAL 1 75#define R592_IO_MODE_PARALLEL 3 76 77 78/* IRQ,card detection,large fifo (first word irq status, second enable) */ 79/* IRQs are ACKed by clearing the bits */ 80#define R592_REG_MSC 0x28 81#define R592_REG_MSC_PRSNT (1 << 1) /* card present (only status)*/ 82#define R592_REG_MSC_IRQ_INSERT (1 << 8) /* detect insert / card insered */ 83#define R592_REG_MSC_IRQ_REMOVE (1 << 9) /* detect removal / card removed */ 84#define R592_REG_MSC_FIFO_EMPTY (1 << 10) /* fifo is empty */ 85#define R592_REG_MSC_FIFO_DMA_DONE (1 << 11) /* dma enable / dma done */ 86 87#define R592_REG_MSC_FIFO_USER_ORN (1 << 12) /* set if software reads empty fifo (if R592_REG_MSC_FIFO_EMPTY is set) */ 88#define R592_REG_MSC_FIFO_MISMATH (1 << 13) /* set if amount of data in fifo doesn't match amount in TPC */ 89#define R592_REG_MSC_FIFO_DMA_ERR (1 << 14) /* IO failure */ 90#define R592_REG_MSC_LED (1 << 15) /* clear to turn led off (only status)*/ 91 92#define DMA_IRQ_ACK_MASK \ 93 (R592_REG_MSC_FIFO_DMA_DONE | R592_REG_MSC_FIFO_DMA_ERR) 94 95#define DMA_IRQ_EN_MASK (DMA_IRQ_ACK_MASK << 16) 96 97#define IRQ_ALL_ACK_MASK 0x00007F00 98#define IRQ_ALL_EN_MASK (IRQ_ALL_ACK_MASK << 16) 99 100/* DMA address for large FIFO read/writes*/ 101#define R592_FIFO_DMA 0x2C 102 103/* PIO access to large FIFO (512 bytes) (big endian)*/ 104#define R592_FIFO_PIO 0x30 105#define R592_LFIFO_SIZE 512 /* large fifo size */ 106 107 108/* large FIFO DMA settings */ 109#define R592_FIFO_DMA_SETTINGS 0x34 110#define R592_FIFO_DMA_SETTINGS_EN (1 << 0) /* DMA enabled */ 111#define R592_FIFO_DMA_SETTINGS_DIR (1 << 1) /* Dma direction (1 read, 0 write) */ 112#define R592_FIFO_DMA_SETTINGS_CAP (1 << 24) /* Dma is aviable */ 113 114/* Maybe just an delay */ 115/* Bits 17..19 are just number */ 116/* bit 16 is set, then bit 20 is waited */ 117/* time to wait is about 50 spins * 2 ^ (bits 17..19) */ 118/* seems to be possible just to ignore */ 119/* Probably debug register */ 120#define R592_REG38 0x38 121#define R592_REG38_CHANGE (1 << 16) /* Start bit */ 122#define R592_REG38_DONE (1 << 20) /* HW set this after the delay */ 123#define R592_REG38_SHIFT 17 124 125/* Debug register, written (0xABCDEF00) when error happens - not used*/ 126#define R592_REG_3C 0x3C 127 128struct r592_device { 129 struct pci_dev *pci_dev; 130 struct memstick_host *host; /* host backpointer */ 131 struct memstick_request *req; /* current request */ 132 133 /* Registers, IRQ */ 134 void __iomem *mmio; 135 int irq; 136 spinlock_t irq_lock; 137 spinlock_t io_thread_lock; 138 struct timer_list detect_timer; 139 140 struct task_struct *io_thread; 141 bool parallel_mode; 142 143 DECLARE_KFIFO(pio_fifo, u8, sizeof(u32)); 144 145 /* DMA area */ 146 int dma_capable; 147 int dma_error; 148 struct completion dma_done; 149 void *dummy_dma_page; 150 dma_addr_t dummy_dma_page_physical_address; 151 152}; 153 154#define DRV_NAME "r592" 155 156 157#define message(format, ...) \ 158 printk(KERN_INFO DRV_NAME ": " format "\n", ## __VA_ARGS__) 159 160#define __dbg(level, format, ...) \ 161 do { \ 162 if (debug >= level) \ 163 printk(KERN_DEBUG DRV_NAME \ 164 ": " format "\n", ## __VA_ARGS__); \ 165 } while (0) 166 167 168#define dbg(format, ...) __dbg(1, format, ## __VA_ARGS__) 169#define dbg_verbose(format, ...) __dbg(2, format, ## __VA_ARGS__) 170#define dbg_reg(format, ...) __dbg(3, format, ## __VA_ARGS__) 171 172#endif