hw-txe-regs.h (8580B)
1/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */ 2/* 3 * Copyright (c) 2013-2014, Intel Corporation. All rights reserved. 4 * Intel Management Engine Interface (Intel MEI) Linux driver 5 */ 6#ifndef _MEI_HW_TXE_REGS_H_ 7#define _MEI_HW_TXE_REGS_H_ 8 9#include "hw.h" 10 11#define SEC_ALIVENESS_TIMER_TIMEOUT (5 * MSEC_PER_SEC) 12#define SEC_ALIVENESS_WAIT_TIMEOUT (1 * MSEC_PER_SEC) 13#define SEC_RESET_WAIT_TIMEOUT (1 * MSEC_PER_SEC) 14#define SEC_READY_WAIT_TIMEOUT (5 * MSEC_PER_SEC) 15#define START_MESSAGE_RESPONSE_WAIT_TIMEOUT (5 * MSEC_PER_SEC) 16#define RESET_CANCEL_WAIT_TIMEOUT (1 * MSEC_PER_SEC) 17 18enum { 19 SEC_BAR, 20 BRIDGE_BAR, 21 22 NUM_OF_MEM_BARS 23}; 24 25/* SeC FW Status Register 26 * 27 * FW uses this register in order to report its status to host. 28 * This register resides in PCI-E config space. 29 */ 30#define PCI_CFG_TXE_FW_STS0 0x40 31# define PCI_CFG_TXE_FW_STS0_WRK_ST_MSK 0x0000000F 32# define PCI_CFG_TXE_FW_STS0_OP_ST_MSK 0x000001C0 33# define PCI_CFG_TXE_FW_STS0_FW_INIT_CMPLT 0x00000200 34# define PCI_CFG_TXE_FW_STS0_ERR_CODE_MSK 0x0000F000 35# define PCI_CFG_TXE_FW_STS0_OP_MODE_MSK 0x000F0000 36# define PCI_CFG_TXE_FW_STS0_RST_CNT_MSK 0x00F00000 37#define PCI_CFG_TXE_FW_STS1 0x48 38 39#define IPC_BASE_ADDR 0x80400 /* SeC IPC Base Address */ 40 41/* IPC Input Doorbell Register */ 42#define SEC_IPC_INPUT_DOORBELL_REG (0x0000 + IPC_BASE_ADDR) 43 44/* IPC Input Status Register 45 * This register indicates whether or not processing of 46 * the most recent command has been completed by the SEC 47 * New commands and payloads should not be written by the Host 48 * until this indicates that the previous command has been processed. 49 */ 50#define SEC_IPC_INPUT_STATUS_REG (0x0008 + IPC_BASE_ADDR) 51# define SEC_IPC_INPUT_STATUS_RDY BIT(0) 52 53/* IPC Host Interrupt Status Register */ 54#define SEC_IPC_HOST_INT_STATUS_REG (0x0010 + IPC_BASE_ADDR) 55#define SEC_IPC_HOST_INT_STATUS_OUT_DB BIT(0) 56#define SEC_IPC_HOST_INT_STATUS_IN_RDY BIT(1) 57#define SEC_IPC_HOST_INT_STATUS_HDCP_M0_RCVD BIT(5) 58#define SEC_IPC_HOST_INT_STATUS_ILL_MEM_ACCESS BIT(17) 59#define SEC_IPC_HOST_INT_STATUS_AES_HKEY_ERR BIT(18) 60#define SEC_IPC_HOST_INT_STATUS_DES_HKEY_ERR BIT(19) 61#define SEC_IPC_HOST_INT_STATUS_TMRMTB_OVERFLOW BIT(21) 62 63/* Convenient mask for pending interrupts */ 64#define SEC_IPC_HOST_INT_STATUS_PENDING \ 65 (SEC_IPC_HOST_INT_STATUS_OUT_DB| \ 66 SEC_IPC_HOST_INT_STATUS_IN_RDY) 67 68/* IPC Host Interrupt Mask Register */ 69#define SEC_IPC_HOST_INT_MASK_REG (0x0014 + IPC_BASE_ADDR) 70 71# define SEC_IPC_HOST_INT_MASK_OUT_DB BIT(0) /* Output Doorbell Int Mask */ 72# define SEC_IPC_HOST_INT_MASK_IN_RDY BIT(1) /* Input Ready Int Mask */ 73 74/* IPC Input Payload RAM */ 75#define SEC_IPC_INPUT_PAYLOAD_REG (0x0100 + IPC_BASE_ADDR) 76/* IPC Shared Payload RAM */ 77#define IPC_SHARED_PAYLOAD_REG (0x0200 + IPC_BASE_ADDR) 78 79/* SeC Address Translation Table Entry 2 - Ctrl 80 * 81 * This register resides also in SeC's PCI-E Memory space. 82 */ 83#define SATT2_CTRL_REG 0x1040 84# define SATT2_CTRL_VALID_MSK BIT(0) 85# define SATT2_CTRL_BR_BASE_ADDR_REG_SHIFT 8 86# define SATT2_CTRL_BRIDGE_HOST_EN_MSK BIT(12) 87 88/* SATT Table Entry 2 SAP Base Address Register */ 89#define SATT2_SAP_BA_REG 0x1044 90/* SATT Table Entry 2 SAP Size Register. */ 91#define SATT2_SAP_SIZE_REG 0x1048 92 /* SATT Table Entry 2 SAP Bridge Address - LSB Register */ 93#define SATT2_BRG_BA_LSB_REG 0x104C 94 95/* Host High-level Interrupt Status Register */ 96#define HHISR_REG 0x2020 97/* Host High-level Interrupt Enable Register 98 * 99 * Resides in PCI memory space. This is the top hierarchy for 100 * interrupts from SeC to host, aggregating both interrupts that 101 * arrive through HICR registers as well as interrupts 102 * that arrive via IPC. 103 */ 104#define HHIER_REG 0x2024 105#define IPC_HHIER_SEC BIT(0) 106#define IPC_HHIER_BRIDGE BIT(1) 107#define IPC_HHIER_MSK (IPC_HHIER_SEC | IPC_HHIER_BRIDGE) 108 109/* Host High-level Interrupt Mask Register. 110 * 111 * Resides in PCI memory space. 112 * This is the top hierarchy for masking interrupts from SeC to host. 113 */ 114#define HHIMR_REG 0x2028 115#define IPC_HHIMR_SEC BIT(0) 116#define IPC_HHIMR_BRIDGE BIT(1) 117 118/* Host High-level IRQ Status Register */ 119#define HHIRQSR_REG 0x202C 120 121/* Host Interrupt Cause Register 0 - SeC IPC Readiness 122 * 123 * This register is both an ICR to Host from PCI Memory Space 124 * and it is also exposed in the SeC memory space. 125 * This register is used by SeC's IPC driver in order 126 * to synchronize with host about IPC interface state. 127 */ 128#define HICR_SEC_IPC_READINESS_REG 0x2040 129#define HICR_SEC_IPC_READINESS_HOST_RDY BIT(0) 130#define HICR_SEC_IPC_READINESS_SEC_RDY BIT(1) 131#define HICR_SEC_IPC_READINESS_SYS_RDY \ 132 (HICR_SEC_IPC_READINESS_HOST_RDY | \ 133 HICR_SEC_IPC_READINESS_SEC_RDY) 134#define HICR_SEC_IPC_READINESS_RDY_CLR BIT(2) 135 136/* Host Interrupt Cause Register 1 - Aliveness Response */ 137/* This register is both an ICR to Host from PCI Memory Space 138 * and it is also exposed in the SeC memory space. 139 * The register may be used by SeC to ACK a host request for aliveness. 140 */ 141#define HICR_HOST_ALIVENESS_RESP_REG 0x2044 142#define HICR_HOST_ALIVENESS_RESP_ACK BIT(0) 143 144/* Host Interrupt Cause Register 2 - SeC IPC Output Doorbell */ 145#define HICR_SEC_IPC_OUTPUT_DOORBELL_REG 0x2048 146 147/* Host Interrupt Status Register. 148 * 149 * Resides in PCI memory space. 150 * This is the main register involved in generating interrupts 151 * from SeC to host via HICRs. 152 * The interrupt generation rules are as follows: 153 * An interrupt will be generated whenever for any i, 154 * there is a transition from a state where at least one of 155 * the following conditions did not hold, to a state where 156 * ALL the following conditions hold: 157 * A) HISR.INT[i]_STS == 1. 158 * B) HIER.INT[i]_EN == 1. 159 */ 160#define HISR_REG 0x2060 161#define HISR_INT_0_STS BIT(0) 162#define HISR_INT_1_STS BIT(1) 163#define HISR_INT_2_STS BIT(2) 164#define HISR_INT_3_STS BIT(3) 165#define HISR_INT_4_STS BIT(4) 166#define HISR_INT_5_STS BIT(5) 167#define HISR_INT_6_STS BIT(6) 168#define HISR_INT_7_STS BIT(7) 169#define HISR_INT_STS_MSK \ 170 (HISR_INT_0_STS | HISR_INT_1_STS | HISR_INT_2_STS) 171 172/* Host Interrupt Enable Register. Resides in PCI memory space. */ 173#define HIER_REG 0x2064 174#define HIER_INT_0_EN BIT(0) 175#define HIER_INT_1_EN BIT(1) 176#define HIER_INT_2_EN BIT(2) 177#define HIER_INT_3_EN BIT(3) 178#define HIER_INT_4_EN BIT(4) 179#define HIER_INT_5_EN BIT(5) 180#define HIER_INT_6_EN BIT(6) 181#define HIER_INT_7_EN BIT(7) 182 183#define HIER_INT_EN_MSK \ 184 (HIER_INT_0_EN | HIER_INT_1_EN | HIER_INT_2_EN) 185 186 187/* SEC Memory Space IPC output payload. 188 * 189 * This register is part of the output payload which SEC provides to host. 190 */ 191#define BRIDGE_IPC_OUTPUT_PAYLOAD_REG 0x20C0 192 193/* SeC Interrupt Cause Register - Host Aliveness Request 194 * This register is both an ICR to SeC and it is also exposed 195 * in the host-visible PCI memory space. 196 * The register is used by host to request SeC aliveness. 197 */ 198#define SICR_HOST_ALIVENESS_REQ_REG 0x214C 199#define SICR_HOST_ALIVENESS_REQ_REQUESTED BIT(0) 200 201 202/* SeC Interrupt Cause Register - Host IPC Readiness 203 * 204 * This register is both an ICR to SeC and it is also exposed 205 * in the host-visible PCI memory space. 206 * This register is used by the host's SeC driver uses in order 207 * to synchronize with SeC about IPC interface state. 208 */ 209#define SICR_HOST_IPC_READINESS_REQ_REG 0x2150 210 211 212#define SICR_HOST_IPC_READINESS_HOST_RDY BIT(0) 213#define SICR_HOST_IPC_READINESS_SEC_RDY BIT(1) 214#define SICR_HOST_IPC_READINESS_SYS_RDY \ 215 (SICR_HOST_IPC_READINESS_HOST_RDY | \ 216 SICR_HOST_IPC_READINESS_SEC_RDY) 217#define SICR_HOST_IPC_READINESS_RDY_CLR BIT(2) 218 219/* SeC Interrupt Cause Register - SeC IPC Output Status 220 * 221 * This register indicates whether or not processing of the most recent 222 * command has been completed by the Host. 223 * New commands and payloads should not be written by SeC until this 224 * register indicates that the previous command has been processed. 225 */ 226#define SICR_SEC_IPC_OUTPUT_STATUS_REG 0x2154 227# define SEC_IPC_OUTPUT_STATUS_RDY BIT(0) 228 229 230 231/* MEI IPC Message payload size 64 bytes */ 232#define PAYLOAD_SIZE 64 233 234/* MAX size for SATT range 32MB */ 235#define SATT_RANGE_MAX (32 << 20) 236 237 238#endif /* _MEI_HW_TXE_REGS_H_ */ 239