sdhci-xenon.h (2905B)
1/* SPDX-License-Identifier: GPL-2.0-only */ 2/* 3 * Copyright (C) 2016 Marvell, All Rights Reserved. 4 * 5 * Author: Hu Ziji <huziji@marvell.com> 6 * Date: 2016-8-24 7 */ 8#ifndef SDHCI_XENON_H_ 9#define SDHCI_XENON_H_ 10 11/* Register Offset of Xenon SDHC self-defined register */ 12#define XENON_SYS_CFG_INFO 0x0104 13#define XENON_SLOT_TYPE_SDIO_SHIFT 24 14#define XENON_NR_SUPPORTED_SLOT_MASK 0x7 15 16#define XENON_SYS_OP_CTRL 0x0108 17#define XENON_AUTO_CLKGATE_DISABLE_MASK BIT(20) 18#define XENON_SDCLK_IDLEOFF_ENABLE_SHIFT 8 19#define XENON_SLOT_ENABLE_SHIFT 0 20 21#define XENON_SYS_EXT_OP_CTRL 0x010C 22#define XENON_MASK_CMD_CONFLICT_ERR BIT(8) 23 24#define XENON_SLOT_OP_STATUS_CTRL 0x0128 25#define XENON_TUN_CONSECUTIVE_TIMES_SHIFT 16 26#define XENON_TUN_CONSECUTIVE_TIMES_MASK 0x7 27#define XENON_TUN_CONSECUTIVE_TIMES 0x4 28#define XENON_TUNING_STEP_SHIFT 12 29#define XENON_TUNING_STEP_MASK 0xF 30#define XENON_TUNING_STEP_DIVIDER BIT(6) 31 32#define XENON_SLOT_EMMC_CTRL 0x0130 33#define XENON_ENABLE_RESP_STROBE BIT(25) 34#define XENON_ENABLE_DATA_STROBE BIT(24) 35 36#define XENON_SLOT_RETUNING_REQ_CTRL 0x0144 37/* retuning compatible */ 38#define XENON_RETUNING_COMPATIBLE 0x1 39 40#define XENON_SLOT_EXT_PRESENT_STATE 0x014C 41#define XENON_DLL_LOCK_STATE 0x1 42 43#define XENON_SLOT_DLL_CUR_DLY_VAL 0x0150 44 45/* Tuning Parameter */ 46#define XENON_TMR_RETUN_NO_PRESENT 0xF 47#define XENON_DEF_TUNING_COUNT 0x9 48 49#define XENON_DEFAULT_SDCLK_FREQ 400000 50#define XENON_LOWEST_SDCLK_FREQ 100000 51 52/* Xenon specific Mode Select value */ 53#define XENON_CTRL_HS200 0x5 54#define XENON_CTRL_HS400 0x6 55 56enum xenon_variant { 57 XENON_A3700, 58 XENON_AP806, 59 XENON_AP807, 60 XENON_CP110 61}; 62 63struct xenon_priv { 64 unsigned char tuning_count; 65 /* idx of SDHC */ 66 u8 sdhc_id; 67 68 /* 69 * eMMC/SD/SDIO require different register settings. 70 * Xenon driver has to recognize card type 71 * before mmc_host->card is not available. 72 * This field records the card type during init. 73 * It is updated in xenon_init_card(). 74 * 75 * It is only valid during initialization after it is updated. 76 * Do not access this variable in normal transfers after 77 * initialization completes. 78 */ 79 unsigned int init_card_type; 80 81 /* 82 * The bus_width, timing, and clock fields in below 83 * record the current ios setting of Xenon SDHC. 84 * Driver will adjust PHY setting if any change to 85 * ios affects PHY timing. 86 */ 87 unsigned char bus_width; 88 unsigned char timing; 89 unsigned int clock; 90 struct clk *axi_clk; 91 92 int phy_type; 93 /* 94 * Contains board-specific PHY parameters 95 * passed from device tree. 96 */ 97 void *phy_params; 98 struct xenon_emmc_phy_regs *emmc_phy_regs; 99 bool restore_needed; 100 enum xenon_variant hw_version; 101}; 102 103int xenon_phy_adj(struct sdhci_host *host, struct mmc_ios *ios); 104int xenon_phy_parse_params(struct device *dev, 105 struct sdhci_host *host); 106void xenon_soc_pad_ctrl(struct sdhci_host *host, 107 unsigned char signal_voltage); 108#endif