Kconfig (3231B)
1# SPDX-License-Identifier: GPL-2.0-only 2# 3# Freescale device configuration 4# 5 6config NET_VENDOR_FREESCALE 7 bool "Freescale devices" 8 default y 9 depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ 10 M523x || M527x || M5272 || M528x || M520x || M532x || \ 11 ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \ 12 ARCH_LAYERSCAPE || COMPILE_TEST 13 help 14 If you have a network (Ethernet) card belonging to this class, say Y. 15 16 Note that the answer to this question doesn't directly affect the 17 kernel: saying N will just cause the configurator to skip all 18 the questions about Freescale devices. If you say Y, you will be 19 asked for your specific card in the following questions. 20 21if NET_VENDOR_FREESCALE 22 23config FEC 24 tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)" 25 depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ 26 ARCH_MXC || SOC_IMX28 || COMPILE_TEST) 27 default ARCH_MXC || SOC_IMX28 if ARM 28 depends on PTP_1588_CLOCK_OPTIONAL 29 select CRC32 30 select PHYLIB 31 imply NET_SELFTESTS 32 help 33 Say Y here if you want to use the built-in 10/100 Fast ethernet 34 controller on some Motorola ColdFire and Freescale i.MX processors. 35 36config FEC_MPC52xx 37 tristate "FEC MPC52xx driver" 38 depends on PPC_MPC52xx && PPC_BESTCOMM 39 select CRC32 40 select PHYLIB 41 select PPC_BESTCOMM_FEC 42 help 43 This option enables support for the MPC5200's on-chip 44 Fast Ethernet Controller 45 If compiled as module, it will be called fec_mpc52xx. 46 47config FEC_MPC52xx_MDIO 48 bool "FEC MPC52xx MDIO bus driver" 49 depends on FEC_MPC52xx 50 default y 51 help 52 The MPC5200's FEC can connect to the Ethernet either with 53 an external MII PHY chip or 10 Mbps 7-wire interface 54 (Motorola? industry standard). 55 If your board uses an external PHY connected to FEC, enable this. 56 If not sure, enable. 57 If compiled as module, it will be called fec_mpc52xx_phy. 58 59source "drivers/net/ethernet/freescale/fs_enet/Kconfig" 60source "drivers/net/ethernet/freescale/fman/Kconfig" 61 62config FSL_PQ_MDIO 63 tristate "Freescale PQ MDIO" 64 select PHYLIB 65 help 66 This driver supports the MDIO bus used by the gianfar and UCC drivers. 67 68config FSL_XGMAC_MDIO 69 tristate "Freescale XGMAC MDIO" 70 select PHYLIB 71 depends on OF 72 select OF_MDIO 73 help 74 This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and 75 on the FMan mEMAC (which supports both Clauses 22 and 45) 76 77config UCC_GETH 78 tristate "Freescale QE Gigabit Ethernet" 79 depends on QUICC_ENGINE && PPC32 80 select FSL_PQ_MDIO 81 select PHYLIB 82 select FIXED_PHY 83 help 84 This driver supports the Gigabit Ethernet mode of the QUICC Engine, 85 which is available on some Freescale SOCs. 86 87config UGETH_TX_ON_DEMAND 88 bool "Transmit on Demand support" 89 depends on UCC_GETH 90 91config GIANFAR 92 tristate "Gianfar Ethernet" 93 depends on HAS_DMA 94 select FSL_PQ_MDIO 95 select PHYLIB 96 select FIXED_PHY 97 select CRC32 98 help 99 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, 100 and MPC86xx family of chips, the eTSEC on LS1021A and the FEC 101 on the 8540. 102 103source "drivers/net/ethernet/freescale/dpaa/Kconfig" 104source "drivers/net/ethernet/freescale/dpaa2/Kconfig" 105source "drivers/net/ethernet/freescale/enetc/Kconfig" 106 107endif # NET_VENDOR_FREESCALE