smsc95xx.h (14687B)
1/* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /*************************************************************************** 3 * 4 * Copyright (C) 2007-2008 SMSC 5 * 6 *****************************************************************************/ 7 8#ifndef _SMSC95XX_H 9#define _SMSC95XX_H 10 11/* Tx command words */ 12#define TX_CMD_A_DATA_OFFSET_ (0x001F0000) /* Data Start Offset */ 13#define TX_CMD_A_FIRST_SEG_ (0x00002000) /* First Segment */ 14#define TX_CMD_A_LAST_SEG_ (0x00001000) /* Last Segment */ 15#define TX_CMD_A_BUF_SIZE_ (0x000007FF) /* Buffer Size */ 16 17#define TX_CMD_B_CSUM_ENABLE (0x00004000) /* TX Checksum Enable */ 18#define TX_CMD_B_ADD_CRC_DIS_ (0x00002000) /* Add CRC Disable */ 19#define TX_CMD_B_DIS_PADDING_ (0x00001000) /* Disable Frame Padding */ 20#define TX_CMD_B_FRAME_LENGTH_ (0x000007FF) /* Frame Length (bytes) */ 21 22/* Rx status word */ 23#define RX_STS_FF_ (0x40000000) /* Filter Fail */ 24#define RX_STS_FL_ (0x3FFF0000) /* Frame Length */ 25#define RX_STS_ES_ (0x00008000) /* Error Summary */ 26#define RX_STS_BF_ (0x00002000) /* Broadcast Frame */ 27#define RX_STS_LE_ (0x00001000) /* Length Error */ 28#define RX_STS_RF_ (0x00000800) /* Runt Frame */ 29#define RX_STS_MF_ (0x00000400) /* Multicast Frame */ 30#define RX_STS_TL_ (0x00000080) /* Frame too long */ 31#define RX_STS_CS_ (0x00000040) /* Collision Seen */ 32#define RX_STS_FT_ (0x00000020) /* Frame Type */ 33#define RX_STS_RW_ (0x00000010) /* Receive Watchdog */ 34#define RX_STS_ME_ (0x00000008) /* MII Error */ 35#define RX_STS_DB_ (0x00000004) /* Dribbling */ 36#define RX_STS_CRC_ (0x00000002) /* CRC Error */ 37 38/* SCSRs - System Control and Status Registers */ 39/* Device ID and Revision Register */ 40#define ID_REV (0x00) 41#define ID_REV_CHIP_ID_MASK_ (0xFFFF0000) 42#define ID_REV_CHIP_REV_MASK_ (0x0000FFFF) 43#define ID_REV_CHIP_ID_9500_ (0x9500) 44#define ID_REV_CHIP_ID_9500A_ (0x9E00) 45#define ID_REV_CHIP_ID_9512_ (0xEC00) 46#define ID_REV_CHIP_ID_9530_ (0x9530) 47#define ID_REV_CHIP_ID_89530_ (0x9E08) 48#define ID_REV_CHIP_ID_9730_ (0x9730) 49 50/* Interrupt Status Register */ 51#define INT_STS (0x08) 52#define INT_STS_MAC_RTO_ (0x00040000) /* MAC Reset Time Out */ 53#define INT_STS_TX_STOP_ (0x00020000) /* TX Stopped */ 54#define INT_STS_RX_STOP_ (0x00010000) /* RX Stopped */ 55#define INT_STS_PHY_INT_ (0x00008000) /* PHY Interrupt */ 56#define INT_STS_TXE_ (0x00004000) /* Transmitter Error */ 57#define INT_STS_TDFU_ (0x00002000) /* TX Data FIFO Underrun */ 58#define INT_STS_TDFO_ (0x00001000) /* TX Data FIFO Overrun */ 59#define INT_STS_RXDF_ (0x00000800) /* RX Dropped Frame */ 60#define INT_STS_GPIOS_ (0x000007FF) /* GPIOs Interrupts */ 61#define INT_STS_CLEAR_ALL_ (0xFFFFFFFF) 62 63/* Receive Configuration Register */ 64#define RX_CFG (0x0C) 65#define RX_FIFO_FLUSH_ (0x00000001) /* Receive FIFO Flush */ 66 67/* Transmit Configuration Register */ 68#define TX_CFG (0x10) 69#define TX_CFG_ON_ (0x00000004) /* Transmitter Enable */ 70#define TX_CFG_STOP_ (0x00000002) /* Stop Transmitter */ 71#define TX_CFG_FIFO_FLUSH_ (0x00000001) /* Transmit FIFO Flush */ 72 73/* Hardware Configuration Register */ 74#define HW_CFG (0x14) 75#define HW_CFG_BIR_ (0x00001000) /* Bulk In Empty Response */ 76#define HW_CFG_LEDB_ (0x00000800) /* Activity LED 80ms Bypass */ 77#define HW_CFG_RXDOFF_ (0x00000600) /* RX Data Offset */ 78#define HW_CFG_SBP_ (0x00000100) /* Stall Bulk Out Pipe Dis. */ 79#define HW_CFG_IME_ (0x00000080) /* Internal MII Visi. Enable */ 80#define HW_CFG_DRP_ (0x00000040) /* Discard Errored RX Frame */ 81#define HW_CFG_MEF_ (0x00000020) /* Mult. ETH Frames/USB pkt */ 82#define HW_CFG_ETC_ (0x00000010) /* EEPROM Timeout Control */ 83#define HW_CFG_LRST_ (0x00000008) /* Soft Lite Reset */ 84#define HW_CFG_PSEL_ (0x00000004) /* External PHY Select */ 85#define HW_CFG_BCE_ (0x00000002) /* Burst Cap Enable */ 86#define HW_CFG_SRST_ (0x00000001) /* Soft Reset */ 87 88/* Receive FIFO Information Register */ 89#define RX_FIFO_INF (0x18) 90#define RX_FIFO_INF_USED_ (0x0000FFFF) /* RX Data FIFO Used Space */ 91 92/* Transmit FIFO Information Register */ 93#define TX_FIFO_INF (0x1C) 94#define TX_FIFO_INF_FREE_ (0x0000FFFF) /* TX Data FIFO Free Space */ 95 96/* Power Management Control Register */ 97#define PM_CTRL (0x20) 98#define PM_CTL_RES_CLR_WKP_STS (0x00000200) /* Resume Clears Wakeup STS */ 99#define PM_CTL_RES_CLR_WKP_EN (0x00000100) /* Resume Clears Wkp Enables */ 100#define PM_CTL_DEV_RDY_ (0x00000080) /* Device Ready */ 101#define PM_CTL_SUS_MODE_ (0x00000060) /* Suspend Mode */ 102#define PM_CTL_SUS_MODE_0 (0x00000000) 103#define PM_CTL_SUS_MODE_1 (0x00000020) 104#define PM_CTL_SUS_MODE_2 (0x00000040) 105#define PM_CTL_SUS_MODE_3 (0x00000060) 106#define PM_CTL_PHY_RST_ (0x00000010) /* PHY Reset */ 107#define PM_CTL_WOL_EN_ (0x00000008) /* Wake On Lan Enable */ 108#define PM_CTL_ED_EN_ (0x00000004) /* Energy Detect Enable */ 109#define PM_CTL_WUPS_ (0x00000003) /* Wake Up Status */ 110#define PM_CTL_WUPS_NO_ (0x00000000) /* No Wake Up Event Detected */ 111#define PM_CTL_WUPS_ED_ (0x00000001) /* Energy Detect */ 112#define PM_CTL_WUPS_WOL_ (0x00000002) /* Wake On Lan */ 113#define PM_CTL_WUPS_MULTI_ (0x00000003) /* Multiple Events Occurred */ 114 115/* LED General Purpose IO Configuration Register */ 116#define LED_GPIO_CFG (0x24) 117#define LED_GPIO_CFG_SPD_LED (0x01000000) /* GPIOz as Speed LED */ 118#define LED_GPIO_CFG_LNK_LED (0x00100000) /* GPIOy as Link LED */ 119#define LED_GPIO_CFG_FDX_LED (0x00010000) /* GPIOx as Full Duplex LED */ 120 121/* General Purpose IO Configuration Register */ 122#define GPIO_CFG (0x28) 123 124/* Automatic Flow Control Configuration Register */ 125#define AFC_CFG (0x2C) 126#define AFC_CFG_HI_ (0x00FF0000) /* Auto Flow Ctrl High Level */ 127#define AFC_CFG_LO_ (0x0000FF00) /* Auto Flow Ctrl Low Level */ 128#define AFC_CFG_BACK_DUR_ (0x000000F0) /* Back Pressure Duration */ 129#define AFC_CFG_FC_MULT_ (0x00000008) /* Flow Ctrl on Mcast Frame */ 130#define AFC_CFG_FC_BRD_ (0x00000004) /* Flow Ctrl on Bcast Frame */ 131#define AFC_CFG_FC_ADD_ (0x00000002) /* Flow Ctrl on Addr. Decode */ 132#define AFC_CFG_FC_ANY_ (0x00000001) /* Flow Ctrl on Any Frame */ 133/* Hi watermark = 15.5Kb (~10 mtu pkts) */ 134/* low watermark = 3k (~2 mtu pkts) */ 135/* backpressure duration = ~ 350us */ 136/* Apply FC on any frame. */ 137#define AFC_CFG_DEFAULT (0x00F830A1) 138 139/* EEPROM Command Register */ 140#define E2P_CMD (0x30) 141#define E2P_CMD_BUSY_ (0x80000000) /* E2P Controller Busy */ 142#define E2P_CMD_MASK_ (0x70000000) /* Command Mask (see below) */ 143#define E2P_CMD_READ_ (0x00000000) /* Read Location */ 144#define E2P_CMD_EWDS_ (0x10000000) /* Erase/Write Disable */ 145#define E2P_CMD_EWEN_ (0x20000000) /* Erase/Write Enable */ 146#define E2P_CMD_WRITE_ (0x30000000) /* Write Location */ 147#define E2P_CMD_WRAL_ (0x40000000) /* Write All */ 148#define E2P_CMD_ERASE_ (0x50000000) /* Erase Location */ 149#define E2P_CMD_ERAL_ (0x60000000) /* Erase All */ 150#define E2P_CMD_RELOAD_ (0x70000000) /* Data Reload */ 151#define E2P_CMD_TIMEOUT_ (0x00000400) /* Set if no resp within 30ms */ 152#define E2P_CMD_LOADED_ (0x00000200) /* Valid EEPROM found */ 153#define E2P_CMD_ADDR_ (0x000001FF) /* Byte aligned address */ 154 155#define MAX_EEPROM_SIZE (512) 156 157/* EEPROM Data Register */ 158#define E2P_DATA (0x34) 159#define E2P_DATA_MASK_ (0x000000FF) /* EEPROM Data Mask */ 160 161/* Burst Cap Register */ 162#define BURST_CAP (0x38) 163#define BURST_CAP_MASK_ (0x000000FF) /* Max burst sent by the UTX */ 164 165/* Configuration Straps Status Register */ 166#define STRAP_STATUS (0x3C) 167#define STRAP_STATUS_PWR_SEL_ (0x00000020) /* Device self-powered */ 168#define STRAP_STATUS_AMDIX_EN_ (0x00000010) /* Auto-MDIX Enabled */ 169#define STRAP_STATUS_PORT_SWAP_ (0x00000008) /* USBD+/USBD- Swapped */ 170#define STRAP_STATUS_EEP_SIZE_ (0x00000004) /* EEPROM Size */ 171#define STRAP_STATUS_RMT_WKP_ (0x00000002) /* Remote Wkp supported */ 172#define STRAP_STATUS_EEP_DISABLE_ (0x00000001) /* EEPROM Disabled */ 173 174/* Data Port Select Register */ 175#define DP_SEL (0x40) 176 177/* Data Port Command Register */ 178#define DP_CMD (0x44) 179 180/* Data Port Address Register */ 181#define DP_ADDR (0x48) 182 183/* Data Port Data 0 Register */ 184#define DP_DATA0 (0x4C) 185 186/* Data Port Data 1 Register */ 187#define DP_DATA1 (0x50) 188 189/* General Purpose IO Wake Enable and Polarity Register */ 190#define GPIO_WAKE (0x64) 191 192/* Interrupt Endpoint Control Register */ 193#define INT_EP_CTL (0x68) 194#define INT_EP_CTL_INTEP_ (0x80000000) /* Always TX Interrupt PKT */ 195#define INT_EP_CTL_MAC_RTO_ (0x00080000) /* MAC Reset Time Out */ 196#define INT_EP_CTL_RX_FIFO_ (0x00040000) /* RX FIFO Has Frame */ 197#define INT_EP_CTL_TX_STOP_ (0x00020000) /* TX Stopped */ 198#define INT_EP_CTL_RX_STOP_ (0x00010000) /* RX Stopped */ 199#define INT_EP_CTL_PHY_INT_ (0x00008000) /* PHY Interrupt */ 200#define INT_EP_CTL_TXE_ (0x00004000) /* TX Error */ 201#define INT_EP_CTL_TDFU_ (0x00002000) /* TX Data FIFO Underrun */ 202#define INT_EP_CTL_TDFO_ (0x00001000) /* TX Data FIFO Overrun */ 203#define INT_EP_CTL_RXDF_ (0x00000800) /* RX Dropped Frame */ 204#define INT_EP_CTL_GPIOS_ (0x000007FF) /* GPIOs Interrupt Enable */ 205 206/* Bulk In Delay Register (units of 16.667ns, until ~1092µs) */ 207#define BULK_IN_DLY (0x6C) 208 209/* MAC CSRs - MAC Control and Status Registers */ 210/* MAC Control Register */ 211#define MAC_CR (0x100) 212#define MAC_CR_RXALL_ (0x80000000) /* Receive All Mode */ 213#define MAC_CR_RCVOWN_ (0x00800000) /* Disable Receive Own */ 214#define MAC_CR_LOOPBK_ (0x00200000) /* Loopback Operation Mode */ 215#define MAC_CR_FDPX_ (0x00100000) /* Full Duplex Mode */ 216#define MAC_CR_MCPAS_ (0x00080000) /* Pass All Multicast */ 217#define MAC_CR_PRMS_ (0x00040000) /* Promiscuous Mode */ 218#define MAC_CR_INVFILT_ (0x00020000) /* Inverse Filtering */ 219#define MAC_CR_PASSBAD_ (0x00010000) /* Pass Bad Frames */ 220#define MAC_CR_HFILT_ (0x00008000) /* Hash Only Filtering Mode */ 221#define MAC_CR_HPFILT_ (0x00002000) /* Hash/Perfect Filt. Mode */ 222#define MAC_CR_LCOLL_ (0x00001000) /* Late Collision Control */ 223#define MAC_CR_BCAST_ (0x00000800) /* Disable Broadcast Frames */ 224#define MAC_CR_DISRTY_ (0x00000400) /* Disable Retry */ 225#define MAC_CR_PADSTR_ (0x00000100) /* Automatic Pad Stripping */ 226#define MAC_CR_BOLMT_MASK (0x000000C0) /* BackOff Limit */ 227#define MAC_CR_DFCHK_ (0x00000020) /* Deferral Check */ 228#define MAC_CR_TXEN_ (0x00000008) /* Transmitter Enable */ 229#define MAC_CR_RXEN_ (0x00000004) /* Receiver Enable */ 230 231/* MAC Address High Register */ 232#define ADDRH (0x104) 233 234/* MAC Address Low Register */ 235#define ADDRL (0x108) 236 237/* Multicast Hash Table High Register */ 238#define HASHH (0x10C) 239 240/* Multicast Hash Table Low Register */ 241#define HASHL (0x110) 242 243/* MII Access Register */ 244#define MII_ADDR (0x114) 245#define MII_WRITE_ (0x02) 246#define MII_BUSY_ (0x01) 247#define MII_READ_ (0x00) /* ~of MII Write bit */ 248 249/* MII Data Register */ 250#define MII_DATA (0x118) 251 252/* Flow Control Register */ 253#define FLOW (0x11C) 254#define FLOW_FCPT_ (0xFFFF0000) /* Pause Time */ 255#define FLOW_FCPASS_ (0x00000004) /* Pass Control Frames */ 256#define FLOW_FCEN_ (0x00000002) /* Flow Control Enable */ 257#define FLOW_FCBSY_ (0x00000001) /* Flow Control Busy */ 258 259/* VLAN1 Tag Register */ 260#define VLAN1 (0x120) 261 262/* VLAN2 Tag Register */ 263#define VLAN2 (0x124) 264 265/* Wake Up Frame Filter Register */ 266#define WUFF (0x128) 267#define LAN9500_WUFF_NUM (4) 268#define LAN9500A_WUFF_NUM (8) 269 270/* Wake Up Control and Status Register */ 271#define WUCSR (0x12C) 272#define WUCSR_WFF_PTR_RST_ (0x80000000) /* WFrame Filter Pointer Rst */ 273#define WUCSR_GUE_ (0x00000200) /* Global Unicast Enable */ 274#define WUCSR_WUFR_ (0x00000040) /* Wakeup Frame Received */ 275#define WUCSR_MPR_ (0x00000020) /* Magic Packet Received */ 276#define WUCSR_WAKE_EN_ (0x00000004) /* Wakeup Frame Enable */ 277#define WUCSR_MPEN_ (0x00000002) /* Magic Packet Enable */ 278 279/* Checksum Offload Engine Control Register */ 280#define COE_CR (0x130) 281#define Tx_COE_EN_ (0x00010000) /* TX Csum Offload Enable */ 282#define Rx_COE_MODE_ (0x00000002) /* RX Csum Offload Mode */ 283#define Rx_COE_EN_ (0x00000001) /* RX Csum Offload Enable */ 284 285/* Vendor-specific PHY Definitions (via MII access) */ 286/* EDPD NLP / crossover time configuration (LAN9500A only) */ 287#define PHY_EDPD_CONFIG (16) 288#define PHY_EDPD_CONFIG_TX_NLP_EN_ ((u16)0x8000) 289#define PHY_EDPD_CONFIG_TX_NLP_1000_ ((u16)0x0000) 290#define PHY_EDPD_CONFIG_TX_NLP_768_ ((u16)0x2000) 291#define PHY_EDPD_CONFIG_TX_NLP_512_ ((u16)0x4000) 292#define PHY_EDPD_CONFIG_TX_NLP_256_ ((u16)0x6000) 293#define PHY_EDPD_CONFIG_RX_1_NLP_ ((u16)0x1000) 294#define PHY_EDPD_CONFIG_RX_NLP_64_ ((u16)0x0000) 295#define PHY_EDPD_CONFIG_RX_NLP_256_ ((u16)0x0400) 296#define PHY_EDPD_CONFIG_RX_NLP_512_ ((u16)0x0800) 297#define PHY_EDPD_CONFIG_RX_NLP_1000_ ((u16)0x0C00) 298#define PHY_EDPD_CONFIG_EXT_CROSSOVER_ ((u16)0x0001) 299#define PHY_EDPD_CONFIG_DEFAULT (PHY_EDPD_CONFIG_TX_NLP_EN_ | \ 300 PHY_EDPD_CONFIG_TX_NLP_768_ | \ 301 PHY_EDPD_CONFIG_RX_1_NLP_) 302 303/* Mode Control/Status Register */ 304#define PHY_MODE_CTRL_STS (17) 305#define MODE_CTRL_STS_EDPWRDOWN_ ((u16)0x2000) 306#define MODE_CTRL_STS_ENERGYON_ ((u16)0x0002) 307 308/* Control/Status Indication Register */ 309#define SPECIAL_CTRL_STS (27) 310#define SPECIAL_CTRL_STS_OVRRD_AMDIX_ ((u16)0x8000) 311#define SPECIAL_CTRL_STS_AMDIX_ENABLE_ ((u16)0x4000) 312#define SPECIAL_CTRL_STS_AMDIX_STATE_ ((u16)0x2000) 313 314/* Interrupt Source Register */ 315#define PHY_INT_SRC (29) 316#define PHY_INT_SRC_ENERGY_ON_ ((u16)0x0080) 317#define PHY_INT_SRC_ANEG_COMP_ ((u16)0x0040) 318#define PHY_INT_SRC_REMOTE_FAULT_ ((u16)0x0020) 319#define PHY_INT_SRC_LINK_DOWN_ ((u16)0x0010) 320 321/* Interrupt Mask Register */ 322#define PHY_INT_MASK (30) 323#define PHY_INT_MASK_ENERGY_ON_ ((u16)0x0080) 324#define PHY_INT_MASK_ANEG_COMP_ ((u16)0x0040) 325#define PHY_INT_MASK_REMOTE_FAULT_ ((u16)0x0020) 326#define PHY_INT_MASK_LINK_DOWN_ ((u16)0x0010) 327#define PHY_INT_MASK_DEFAULT_ (PHY_INT_MASK_ANEG_COMP_ | \ 328 PHY_INT_MASK_LINK_DOWN_) 329/* PHY Special Control/Status Register */ 330#define PHY_SPECIAL (31) 331#define PHY_SPECIAL_SPD_ ((u16)0x001C) 332#define PHY_SPECIAL_SPD_10HALF_ ((u16)0x0004) 333#define PHY_SPECIAL_SPD_10FULL_ ((u16)0x0014) 334#define PHY_SPECIAL_SPD_100HALF_ ((u16)0x0008) 335#define PHY_SPECIAL_SPD_100FULL_ ((u16)0x0018) 336 337/* USB Vendor Requests */ 338#define USB_VENDOR_REQUEST_WRITE_REGISTER 0xA0 339#define USB_VENDOR_REQUEST_READ_REGISTER 0xA1 340#define USB_VENDOR_REQUEST_GET_STATS 0xA2 341 342/* Interrupt Endpoint status word bitfields */ 343#define INT_ENP_MAC_RTO_ ((u32)BIT(18)) /* MAC Reset Time Out */ 344#define INT_ENP_TX_STOP_ ((u32)BIT(17)) /* TX Stopped */ 345#define INT_ENP_RX_STOP_ ((u32)BIT(16)) /* RX Stopped */ 346#define INT_ENP_PHY_INT_ ((u32)BIT(15)) /* PHY Interrupt */ 347#define INT_ENP_TXE_ ((u32)BIT(14)) /* TX Error */ 348#define INT_ENP_TDFU_ ((u32)BIT(13)) /* TX FIFO Underrun */ 349#define INT_ENP_TDFO_ ((u32)BIT(12)) /* TX FIFO Overrun */ 350#define INT_ENP_RXDF_ ((u32)BIT(11)) /* RX Dropped Frame */ 351 352#endif /* _SMSC95XX_H */