pwrseq.h (12917B)
1/* SPDX-License-Identifier: GPL-2.0 */ 2/* Copyright(c) 2009-2013 Realtek Corporation.*/ 3 4#ifndef __RTL8723E_PWRSEQ_H__ 5#define __RTL8723E_PWRSEQ_H__ 6 7#include "../pwrseqcmd.h" 8/* Check document WM-20110607-Paul-RTL8188EE_Power_Architecture-R02.vsd 9 * There are 6 HW Power States: 10 * 0: POFF--Power Off 11 * 1: PDN--Power Down 12 * 2: CARDEMU--Card Emulation 13 * 3: ACT--Active Mode 14 * 4: LPS--Low Power State 15 * 5: SUS--Suspend 16 * 17 * The transision from different states are defined below 18 * TRANS_CARDEMU_TO_ACT 19 * TRANS_ACT_TO_CARDEMU 20 * TRANS_CARDEMU_TO_SUS 21 * TRANS_SUS_TO_CARDEMU 22 * TRANS_CARDEMU_TO_PDN 23 * TRANS_ACT_TO_LPS 24 * TRANS_LPS_TO_ACT 25 * 26 * TRANS_END 27 * PWR SEQ Version: rtl8188ee_PwrSeq_V09.h 28 */ 29 30#define RTL8188EE_TRANS_CARDEMU_TO_ACT_STEPS 10 31#define RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS 10 32#define RTL8188EE_TRANS_CARDEMU_TO_SUS_STEPS 10 33#define RTL8188EE_TRANS_SUS_TO_CARDEMU_STEPS 10 34#define RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS 10 35#define RTL8188EE_TRANS_PDN_TO_CARDEMU_STEPS 10 36#define RTL8188EE_TRANS_ACT_TO_LPS_STEPS 15 37#define RTL8188EE_TRANS_LPS_TO_ACT_STEPS 15 38#define RTL8188EE_TRANS_END_STEPS 1 39 40/* The following macros have the following format: 41 * { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value 42 * comments }, 43 */ 44#define RTL8188EE_TRANS_CARDEMU_TO_ACT \ 45 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 46 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1) \ 47 /* wait till 0x04[17] = 1 power ready*/}, \ 48 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 49 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0)|BIT(1), 0 \ 50 /* 0x02[1:0] = 0 reset BB*/}, \ 51 {0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 52 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7) \ 53 /*0x24[23] = 2b'01 schmit trigger */}, \ 54 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 55 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0 \ 56 /* 0x04[15] = 0 disable HWPDN (control by DRV)*/}, \ 57 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 58 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4)|BIT(3), 0 \ 59 /*0x04[12:11] = 2b'00 disable WL suspend*/}, \ 60 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 61 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0) \ 62 /*0x04[8] = 1 polling until return 0*/}, \ 63 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 64 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0 \ 65 /*wait till 0x04[8] = 0*/}, \ 66 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 67 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \ 68 /*LDO normal mode*/}, \ 69 {0x0074, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 70 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \ 71 /*SDIO Driving*/}, 72 73#define RTL8188EE_TRANS_ACT_TO_CARDEMU \ 74 {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 75 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 76 /*0x1F[7:0] = 0 turn off RF*/}, \ 77 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 78 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \ 79 /*LDO Sleep mode*/}, \ 80 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 81 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1) \ 82 /*0x04[9] = 1 turn off MAC by HW state machine*/}, \ 83 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 84 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0 \ 85 /*wait till 0x04[9] = 0 polling until return 0 to disable*/}, 86 87#define RTL8188EE_TRANS_CARDEMU_TO_SUS \ 88 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 89 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ 90 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3) \ 91 /*0x04[12:11] = 2b'01enable WL suspend*/}, \ 92 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ 93 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)|BIT(4) \ 94 /*0x04[12:11] = 2b'11enable WL suspend for PCIe*/}, \ 95 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 96 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ 97 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, BIT(7) \ 98 /* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */},\ 99 {0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 100 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ 101 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \ 102 /*Clear SIC_EN register 0x40[12] = 1'b0 */}, \ 103 {0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 104 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ 105 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \ 106 /*Set USB suspend enable local register 0xfe10[4]=1 */}, \ 107 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 108 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0) \ 109 /*Set SDIO suspend local register*/}, \ 110 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 111 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0 \ 112 /*wait power state to suspend*/}, 113 114#define RTL8188EE_TRANS_SUS_TO_CARDEMU \ 115 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 116 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0 \ 117 /*Set SDIO suspend local register*/}, \ 118 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 119 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1) \ 120 /*wait power state to suspend*/}, \ 121 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 122 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), 0 \ 123 /*0x04[12:11] = 2b'00 disable WL suspend*/}, 124 125#define RTL8188EE_TRANS_CARDEMU_TO_CARDDIS \ 126 {0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 127 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7) \ 128 /*0x24[23] = 2b'01 schmit trigger */}, \ 129 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 130 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ 131 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3) \ 132 /*0x04[12:11] = 2b'01 enable WL suspend*/}, \ 133 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 134 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ 135 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 136 /* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */},\ 137 {0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 138 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ 139 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \ 140 /*Clear SIC_EN register 0x40[12] = 1'b0 */}, \ 141 {0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \ 142 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \ 143 /*Set USB suspend enable local register 0xfe10[4]=1 */}, \ 144 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 145 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0) \ 146 /*Set SDIO suspend local register*/}, \ 147 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 148 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0 \ 149 /*wait power state to suspend*/}, 150 151#define RTL8188EE_TRANS_CARDDIS_TO_CARDEMU \ 152 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 153 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0 \ 154 /*Set SDIO suspend local register*/}, \ 155 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 156 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1) \ 157 /*wait power state to suspend*/}, \ 158 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 159 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0 \ 160 /*0x04[12:11] = 2b'00 disable WL suspend*/}, 161 162#define RTL8188EE_TRANS_CARDEMU_TO_PDN \ 163 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 164 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0/* 0x04[16] = 0*/}, \ 165 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 166 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7) \ 167 /* 0x04[15] = 1*/}, 168 169#define RTL8188EE_TRANS_PDN_TO_CARDEMU \ 170 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 171 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0/* 0x04[15] = 0*/}, 172 173#define RTL8188EE_TRANS_ACT_TO_LPS \ 174 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 175 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x7F \ 176 /*Tx Pause*/}, \ 177 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 178 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 179 /*Should be zero if no packet is transmitting*/}, \ 180 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 181 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 182 /*Should be zero if no packet is transmitting*/}, \ 183 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 184 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 185 /*Should be zero if no packet is transmitting*/}, \ 186 {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 187 PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ 188 /*Should be zero if no packet is transmitting*/}, \ 189 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 190 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0 \ 191 /*CCK and OFDM are disabled,and clock are gated*/}, \ 192 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 193 PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US \ 194 /*Delay 1us*/}, \ 195 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 196 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F \ 197 /*Reset MAC TRX*/}, \ 198 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 199 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0 \ 200 /*check if removed later*/}, \ 201 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 202 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5) \ 203 /*Respond TxOK to scheduler*/}, 204 205 206#define RTL8188EE_TRANS_LPS_TO_ACT \ 207 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ 208 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84 \ 209 /*SDIO RPWM*/}, \ 210 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \ 211 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \ 212 /*USB RPWM*/}, \ 213 {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ 214 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \ 215 /*PCIe RPWM*/}, \ 216 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 217 PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS \ 218 /*Delay*/}, \ 219 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 220 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \ 221 /*. 0x08[4] = 0 switch TSF to 40M*/}, \ 222 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 223 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(7), 0 \ 224 /*Polling 0x109[7]=0 TSF in 40M*/}, \ 225 {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 226 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6)|BIT(7), 0 \ 227 /*. 0x29[7:6] = 2b'00 enable BB clock*/}, \ 228 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 229 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1) \ 230 /*. 0x101[1] = 1*/}, \ 231 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 232 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF \ 233 /*. 0x100[7:0] = 0xFF enable WMAC TRX*/}, \ 234 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 235 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1)|BIT(0), BIT(1)|BIT(0) \ 236 /*. 0x02[1:0] = 2b'11 enable BB macro*/}, \ 237 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ 238 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ 239 /*. 0x522 = 0*/}, 240 241#define RTL8188EE_TRANS_END \ 242 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 243 0, PWR_CMD_END, 0, 0} 244 245extern struct wlan_pwr_cfg rtl8188ee_power_on_flow 246 [RTL8188EE_TRANS_CARDEMU_TO_ACT_STEPS + 247 RTL8188EE_TRANS_END_STEPS]; 248extern struct wlan_pwr_cfg rtl8188ee_radio_off_flow 249 [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + 250 RTL8188EE_TRANS_END_STEPS]; 251extern struct wlan_pwr_cfg rtl8188ee_card_disable_flow 252 [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + 253 RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS + 254 RTL8188EE_TRANS_END_STEPS]; 255extern struct wlan_pwr_cfg rtl8188ee_card_enable_flow 256 [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + 257 RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS + 258 RTL8188EE_TRANS_END_STEPS]; 259extern struct wlan_pwr_cfg rtl8188ee_suspend_flow 260 [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + 261 RTL8188EE_TRANS_CARDEMU_TO_SUS_STEPS + 262 RTL8188EE_TRANS_END_STEPS]; 263extern struct wlan_pwr_cfg rtl8188ee_resume_flow 264 [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + 265 RTL8188EE_TRANS_CARDEMU_TO_SUS_STEPS + 266 RTL8188EE_TRANS_END_STEPS]; 267extern struct wlan_pwr_cfg rtl8188ee_hwpdn_flow 268 [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + 269 RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS + 270 RTL8188EE_TRANS_END_STEPS]; 271extern struct wlan_pwr_cfg rtl8188ee_enter_lps_flow 272 [RTL8188EE_TRANS_ACT_TO_LPS_STEPS + 273 RTL8188EE_TRANS_END_STEPS]; 274extern struct wlan_pwr_cfg rtl8188ee_leave_lps_flow 275 [RTL8188EE_TRANS_LPS_TO_ACT_STEPS + 276 RTL8188EE_TRANS_END_STEPS]; 277 278/* RTL8723 Power Configuration CMDs for PCIe interface */ 279#define RTL8188EE_NIC_PWR_ON_FLOW rtl8188ee_power_on_flow 280#define RTL8188EE_NIC_RF_OFF_FLOW rtl8188ee_radio_off_flow 281#define RTL8188EE_NIC_DISABLE_FLOW rtl8188ee_card_disable_flow 282#define RTL8188EE_NIC_ENABLE_FLOW rtl8188ee_card_enable_flow 283#define RTL8188EE_NIC_SUSPEND_FLOW rtl8188ee_suspend_flow 284#define RTL8188EE_NIC_RESUME_FLOW rtl8188ee_resume_flow 285#define RTL8188EE_NIC_PDN_FLOW rtl8188ee_hwpdn_flow 286#define RTL8188EE_NIC_LPS_ENTER_FLOW rtl8188ee_enter_lps_flow 287#define RTL8188EE_NIC_LPS_LEAVE_FLOW rtl8188ee_leave_lps_flow 288 289#endif