pwrseq.h (12352B)
1/* SPDX-License-Identifier: GPL-2.0 */ 2/* Copyright(c) 2009-2012 Realtek Corporation.*/ 3 4#ifndef __RTL8723E_PWRSEQ_H__ 5#define __RTL8723E_PWRSEQ_H__ 6 7#include "../pwrseqcmd.h" 8/* 9 * Check document WM-20110607-Paul-RTL8723A_Power_Architecture-R02.vsd 10 * There are 6 HW Power States: 11 * 0: POFF--Power Off 12 * 1: PDN--Power Down 13 * 2: CARDEMU--Card Emulation 14 * 3: ACT--Active Mode 15 * 4: LPS--Low Power State 16 * 5: SUS--Suspend 17 * 18 * The transision from different states are defined below 19 * TRANS_CARDEMU_TO_ACT 20 * TRANS_ACT_TO_CARDEMU 21 * TRANS_CARDEMU_TO_SUS 22 * TRANS_SUS_TO_CARDEMU 23 * TRANS_CARDEMU_TO_PDN 24 * TRANS_ACT_TO_LPS 25 * TRANS_LPS_TO_ACT 26 * 27 * TRANS_END 28 */ 29 30#define RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS 10 31#define RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS 10 32#define RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS 10 33#define RTL8723A_TRANS_SUS_TO_CARDEMU_STEPS 10 34#define RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS 10 35#define RTL8723A_TRANS_PDN_TO_CARDEMU_STEPS 10 36#define RTL8723A_TRANS_ACT_TO_LPS_STEPS 15 37#define RTL8723A_TRANS_LPS_TO_ACT_STEPS 15 38#define RTL8723A_TRANS_END_STEPS 1 39 40/* format */ 41/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }*/ 42 43#define RTL8723A_TRANS_CARDEMU_TO_ACT \ 44 /* disable SW LPS 0x04[10]=0*/ \ 45 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 46 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), 0},\ 47 /* wait till 0x04[17] = 1 power ready*/ \ 48 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 49 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},\ 50 /* release WLON reset 0x04[16]=1*/ \ 51 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 52 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},\ 53 /* disable HWPDN 0x04[15]=0*/ \ 54 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 55 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},\ 56 /* disable WL suspend*/ \ 57 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 58 PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0},\ 59 /* polling until return 0*/ \ 60 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 61 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},\ 62 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 63 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0}, 64 65/* format */ 66/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 67 68#define RTL8723A_TRANS_ACT_TO_CARDEMU \ 69 /*0x1F[7:0] = 0 turn off RF*/ \ 70 {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 71 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, \ 72 {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 73 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},\ 74 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 75 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \ 76 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 77 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, 78 79/* format */ 80/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/ 81#define RTL8723A_TRANS_CARDEMU_TO_SUS \ 82 /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ 83 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 84 PWR_BASEADDR_MAC, PWR_CMD_WRITE, \ 85 BIT(4)|BIT(3), (BIT(4)|BIT(3))},\ 86/*0x04[12:11] = 2b'01 enable WL suspend*/ \ 87 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK| \ 88 PWR_INTF_SDIO_MSK,\ 89 PWR_BASEADDR_MAC, \ 90 PWR_CMD_WRITE, \ 91 BIT(3)|BIT(4), BIT(3)}, \ 92/*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ 93 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 94 PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, \ 95 PWR_CMD_WRITE, BIT(3)|BIT(4), \ 96 BIT(3)|BIT(4)}, \ 97/*Set SDIO suspend local register*/ \ 98 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 99 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 100 PWR_CMD_WRITE, BIT(0), BIT(0)}, \ 101/*wait power state to suspend*/ \ 102 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 103 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 104 PWR_CMD_POLLING, BIT(1), 0}, 105 106/* format */ 107/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 108 109#define RTL8723A_TRANS_SUS_TO_CARDEMU \ 110 /*Set SDIO suspend local register*/ \ 111 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 112 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0},\ 113 /*wait power state to suspend*/ \ 114 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 115 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)},\ 116 /*0x04[12:11] = 2b'00 disable WL suspend*/ \ 117 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 118 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, 119 120/* format */ 121/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 122 123#define RTL8723A_TRANS_CARDEMU_TO_CARDDIS \ 124 /*0x04[12:11] = 2b'01 enable WL suspend*/ \ 125 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 126 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ 127 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, \ 128/*0x04[10] = 1, enable SW LPS*/ \ 129 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 130 PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC,\ 131 PWR_CMD_WRITE, BIT(2), BIT(2)}, \ 132/*Set SDIO suspend local register*/ \ 133 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 134 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 135 PWR_CMD_WRITE, BIT(0), BIT(0)}, \ 136 /*wait power state to suspend*/ \ 137 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 138 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 139 PWR_CMD_POLLING, BIT(1), 0}, 140 141/* format */ 142/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 143 144#define RTL8723A_TRANS_CARDDIS_TO_CARDEMU\ 145/*Set SDIO suspend local register*/ \ 146 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 147 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 148 PWR_CMD_WRITE, BIT(0), 0}, \ 149 /*wait power state to suspend*/ \ 150 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 151 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 152 PWR_CMD_POLLING, BIT(1), BIT(1)},\ 153 /*0x04[12:11] = 2b'00 disable WL suspend*/ \ 154 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 155 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 156 PWR_CMD_WRITE, BIT(3)|BIT(4), 0},\ 157/*PCIe DMA start*/ \ 158 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 159 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 160 PWR_CMD_WRITE, 0xFF, 0}, 161 162/* format */ 163/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 164#define RTL8723A_TRANS_CARDEMU_TO_PDN \ 165 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 166 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 167 PWR_CMD_WRITE, BIT(0), 0},/* 0x04[16] = 0*/\ 168 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 169 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 170 PWR_CMD_WRITE, BIT(7), BIT(7)},/* 0x04[15] = 1*/ 171 172/* format */ 173/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 174#define RTL8723A_TRANS_PDN_TO_CARDEMU \ 175 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 176 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 177 PWR_CMD_WRITE, BIT(7), 0},/* 0x04[15] = 0*/ 178 179/* format */ 180/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 181 182#define RTL8723A_TRANS_ACT_TO_LPS \ 183 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 184 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 185 PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \ 186 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 187 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 188 PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/ \ 189 /*Should be zero if no packet is transmitting*/ \ 190 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 191 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 192 PWR_CMD_POLLING, 0xFF, 0},\ 193 /*Should be zero if no packet is transmitting*/ \ 194 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 195 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 196 PWR_CMD_POLLING, 0xFF, 0},\ 197 /*Should be zero if no packet is transmitting*/ \ 198 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 199 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 200 PWR_CMD_POLLING, 0xFF, 0},\ 201 /*Should be zero if no packet is transmitting*/ \ 202 {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 203 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 204 PWR_CMD_POLLING, 0xFF, 0},\ 205 /*CCK and OFDM are disabled,and clock are gated*/ \ 206 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 207 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 208 PWR_CMD_WRITE, BIT(0), 0},\ 209 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 210 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 211 PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/\ 212 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 213 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 214 PWR_CMD_WRITE, BIT(1), 0},/*Whole BB is reset*/ \ 215 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 216 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 217 PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \ 218 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 219 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 220 PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/ \ 221 /*Respond TxOK to scheduler*/ \ 222 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 223 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 224 PWR_CMD_WRITE, BIT(5), BIT(5)},\ 225 226#define RTL8723A_TRANS_LPS_TO_ACT\ 227/* format */ \ 228/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ \ 229 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 230 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 231 PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\ 232 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 233 PWR_INTF_USB_MSK, PWR_BASEADDR_MAC,\ 234 PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\ 235 {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 236 PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC,\ 237 PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\ 238 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 239 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 240 PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\ 241 /*. 0x08[4] = 0 switch TSF to 40M*/\ 242 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 243 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 244 PWR_CMD_WRITE, BIT(4), 0}, \ 245 /*Polling 0x109[7]=0 TSF in 40M*/\ 246 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 247 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 248 PWR_CMD_POLLING, BIT(7), 0}, \ 249 /*. 0x29[7:6] = 2b'00 enable BB clock*/\ 250 {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 251 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 252 PWR_CMD_WRITE, BIT(6)|BIT(7), 0},\ 253 /*. 0x101[1] = 1*/\ 254 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 255 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 256 PWR_CMD_WRITE, BIT(1), BIT(1)},\ 257 /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\ 258 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 259 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 260 PWR_CMD_WRITE, 0xFF, 0xFF},\ 261 /*. 0x02[1:0] = 2b'11 enable BB macro*/\ 262 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 263 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 264 PWR_CMD_WRITE, BIT(1)|BIT(0), BIT(1)|BIT(0)},\ 265 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 266 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 267 PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ 268 269/* format */ 270/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 271 272#define RTL8723A_TRANS_END \ 273 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 274 0, PWR_CMD_END, 0, 0} 275 276extern struct wlan_pwr_cfg rtl8723A_power_on_flow 277 [RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS + 278 RTL8723A_TRANS_END_STEPS]; 279extern struct wlan_pwr_cfg rtl8723A_radio_off_flow 280 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 281 RTL8723A_TRANS_END_STEPS]; 282extern struct wlan_pwr_cfg rtl8723A_card_disable_flow 283 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 284 RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS + 285 RTL8723A_TRANS_END_STEPS]; 286extern struct wlan_pwr_cfg rtl8723A_card_enable_flow 287 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 288 RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS + 289 RTL8723A_TRANS_END_STEPS]; 290extern struct wlan_pwr_cfg rtl8723A_suspend_flow 291 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 292 RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS + 293 RTL8723A_TRANS_END_STEPS]; 294extern struct wlan_pwr_cfg rtl8723A_resume_flow 295 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 296 RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS + 297 RTL8723A_TRANS_END_STEPS]; 298extern struct wlan_pwr_cfg rtl8723A_hwpdn_flow 299 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 300 RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS + 301 RTL8723A_TRANS_END_STEPS]; 302extern struct wlan_pwr_cfg rtl8723A_enter_lps_flow 303 [RTL8723A_TRANS_ACT_TO_LPS_STEPS + RTL8723A_TRANS_END_STEPS]; 304extern struct wlan_pwr_cfg rtl8723A_leave_lps_flow 305 [RTL8723A_TRANS_LPS_TO_ACT_STEPS + RTL8723A_TRANS_END_STEPS]; 306 307/* RTL8723 Power Configuration CMDs for PCIe interface */ 308#define RTL8723_NIC_PWR_ON_FLOW rtl8723A_power_on_flow 309#define RTL8723_NIC_RF_OFF_FLOW rtl8723A_radio_off_flow 310#define RTL8723_NIC_DISABLE_FLOW rtl8723A_card_disable_flow 311#define RTL8723_NIC_ENABLE_FLOW rtl8723A_card_enable_flow 312#define RTL8723_NIC_SUSPEND_FLOW rtl8723A_suspend_flow 313#define RTL8723_NIC_RESUME_FLOW rtl8723A_resume_flow 314#define RTL8723_NIC_PDN_FLOW rtl8723A_hwpdn_flow 315#define RTL8723_NIC_LPS_ENTER_FLOW rtl8723A_enter_lps_flow 316#define RTL8723_NIC_LPS_LEAVE_FLOW rtl8723A_leave_lps_flow 317 318#endif