mv_94xx.h (10232B)
1/* SPDX-License-Identifier: GPL-2.0-only */ 2/* 3 * Marvell 88SE94xx hardware specific head file 4 * 5 * Copyright 2007 Red Hat, Inc. 6 * Copyright 2008 Marvell. <kewei@marvell.com> 7 * Copyright 2009-2011 Marvell. <yuxiangl@marvell.com> 8*/ 9 10#ifndef _MVS94XX_REG_H_ 11#define _MVS94XX_REG_H_ 12 13#include <linux/types.h> 14 15#define MAX_LINK_RATE SAS_LINK_RATE_6_0_GBPS 16 17enum VANIR_REVISION_ID { 18 VANIR_A0_REV = 0xA0, 19 VANIR_B0_REV = 0x01, 20 VANIR_C0_REV = 0x02, 21 VANIR_C1_REV = 0x03, 22 VANIR_C2_REV = 0xC2, 23}; 24 25enum host_registers { 26 MVS_HST_CHIP_CONFIG = 0x10104, /* chip configuration */ 27}; 28 29enum hw_registers { 30 MVS_GBL_CTL = 0x04, /* global control */ 31 MVS_GBL_INT_STAT = 0x00, /* global irq status */ 32 MVS_GBL_PI = 0x0C, /* ports implemented bitmask */ 33 34 MVS_PHY_CTL = 0x40, /* SOC PHY Control */ 35 MVS_PORTS_IMP = 0x9C, /* SOC Port Implemented */ 36 37 MVS_GBL_PORT_TYPE = 0xa0, /* port type */ 38 39 MVS_CTL = 0x100, /* SAS/SATA port configuration */ 40 MVS_PCS = 0x104, /* SAS/SATA port control/status */ 41 MVS_CMD_LIST_LO = 0x108, /* cmd list addr */ 42 MVS_CMD_LIST_HI = 0x10C, 43 MVS_RX_FIS_LO = 0x110, /* RX FIS list addr */ 44 MVS_RX_FIS_HI = 0x114, 45 MVS_STP_REG_SET_0 = 0x118, /* STP/SATA Register Set Enable */ 46 MVS_STP_REG_SET_1 = 0x11C, 47 MVS_TX_CFG = 0x120, /* TX configuration */ 48 MVS_TX_LO = 0x124, /* TX (delivery) ring addr */ 49 MVS_TX_HI = 0x128, 50 51 MVS_TX_PROD_IDX = 0x12C, /* TX producer pointer */ 52 MVS_TX_CONS_IDX = 0x130, /* TX consumer pointer (RO) */ 53 MVS_RX_CFG = 0x134, /* RX configuration */ 54 MVS_RX_LO = 0x138, /* RX (completion) ring addr */ 55 MVS_RX_HI = 0x13C, 56 MVS_RX_CONS_IDX = 0x140, /* RX consumer pointer (RO) */ 57 58 MVS_INT_COAL = 0x148, /* Int coalescing config */ 59 MVS_INT_COAL_TMOUT = 0x14C, /* Int coalescing timeout */ 60 MVS_INT_STAT = 0x150, /* Central int status */ 61 MVS_INT_MASK = 0x154, /* Central int enable */ 62 MVS_INT_STAT_SRS_0 = 0x158, /* SATA register set status */ 63 MVS_INT_MASK_SRS_0 = 0x15C, 64 MVS_INT_STAT_SRS_1 = 0x160, 65 MVS_INT_MASK_SRS_1 = 0x164, 66 MVS_NON_NCQ_ERR_0 = 0x168, /* SRS Non-specific NCQ Error */ 67 MVS_NON_NCQ_ERR_1 = 0x16C, 68 MVS_CMD_ADDR = 0x170, /* Command register port (addr) */ 69 MVS_CMD_DATA = 0x174, /* Command register port (data) */ 70 MVS_MEM_PARITY_ERR = 0x178, /* Memory parity error */ 71 72 /* ports 1-3 follow after this */ 73 MVS_P0_INT_STAT = 0x180, /* port0 interrupt status */ 74 MVS_P0_INT_MASK = 0x184, /* port0 interrupt mask */ 75 /* ports 5-7 follow after this */ 76 MVS_P4_INT_STAT = 0x1A0, /* Port4 interrupt status */ 77 MVS_P4_INT_MASK = 0x1A4, /* Port4 interrupt enable mask */ 78 79 /* ports 1-3 follow after this */ 80 MVS_P0_SER_CTLSTAT = 0x1D0, /* port0 serial control/status */ 81 /* ports 5-7 follow after this */ 82 MVS_P4_SER_CTLSTAT = 0x1E0, /* port4 serial control/status */ 83 84 /* ports 1-3 follow after this */ 85 MVS_P0_CFG_ADDR = 0x200, /* port0 phy register address */ 86 MVS_P0_CFG_DATA = 0x204, /* port0 phy register data */ 87 /* ports 5-7 follow after this */ 88 MVS_P4_CFG_ADDR = 0x220, /* Port4 config address */ 89 MVS_P4_CFG_DATA = 0x224, /* Port4 config data */ 90 91 /* phys 1-3 follow after this */ 92 MVS_P0_VSR_ADDR = 0x250, /* phy0 VSR address */ 93 MVS_P0_VSR_DATA = 0x254, /* phy0 VSR data */ 94 /* phys 1-3 follow after this */ 95 /* multiplexing */ 96 MVS_P4_VSR_ADDR = 0x250, /* phy4 VSR address */ 97 MVS_P4_VSR_DATA = 0x254, /* phy4 VSR data */ 98 MVS_PA_VSR_ADDR = 0x290, /* All port VSR addr */ 99 MVS_PA_VSR_PORT = 0x294, /* All port VSR data */ 100 MVS_COMMAND_ACTIVE = 0x300, 101}; 102 103enum pci_cfg_registers { 104 PCR_PHY_CTL = 0x40, 105 PCR_PHY_CTL2 = 0x90, 106 PCR_DEV_CTRL = 0x78, 107 PCR_LINK_STAT = 0x82, 108}; 109 110/* SAS/SATA Vendor Specific Port Registers */ 111enum sas_sata_vsp_regs { 112 VSR_PHY_STAT = 0x00 * 4, /* Phy Interrupt Status */ 113 VSR_PHY_MODE1 = 0x01 * 4, /* phy Interrupt Enable */ 114 VSR_PHY_MODE2 = 0x02 * 4, /* Phy Configuration */ 115 VSR_PHY_MODE3 = 0x03 * 4, /* Phy Status */ 116 VSR_PHY_MODE4 = 0x04 * 4, /* Phy Counter 0 */ 117 VSR_PHY_MODE5 = 0x05 * 4, /* Phy Counter 1 */ 118 VSR_PHY_MODE6 = 0x06 * 4, /* Event Counter Control */ 119 VSR_PHY_MODE7 = 0x07 * 4, /* Event Counter Select */ 120 VSR_PHY_MODE8 = 0x08 * 4, /* Event Counter 0 */ 121 VSR_PHY_MODE9 = 0x09 * 4, /* Event Counter 1 */ 122 VSR_PHY_MODE10 = 0x0A * 4, /* Event Counter 2 */ 123 VSR_PHY_MODE11 = 0x0B * 4, /* Event Counter 3 */ 124 VSR_PHY_ACT_LED = 0x0C * 4, /* Activity LED control */ 125 126 VSR_PHY_FFE_CONTROL = 0x10C, 127 VSR_PHY_DFE_UPDATE_CRTL = 0x110, 128 VSR_REF_CLOCK_CRTL = 0x1A0, 129}; 130 131enum chip_register_bits { 132 PHY_MIN_SPP_PHYS_LINK_RATE_MASK = (0x7 << 8), 133 PHY_MAX_SPP_PHYS_LINK_RATE_MASK = (0x7 << 12), 134 PHY_NEG_SPP_PHYS_LINK_RATE_MASK_OFFSET = (16), 135 PHY_NEG_SPP_PHYS_LINK_RATE_MASK = 136 (0x3 << PHY_NEG_SPP_PHYS_LINK_RATE_MASK_OFFSET), 137}; 138 139enum pci_interrupt_cause { 140 /* MAIN_IRQ_CAUSE (R10200) Bits*/ 141 MVS_IRQ_COM_IN_I2O_IOP0 = (1 << 0), 142 MVS_IRQ_COM_IN_I2O_IOP1 = (1 << 1), 143 MVS_IRQ_COM_IN_I2O_IOP2 = (1 << 2), 144 MVS_IRQ_COM_IN_I2O_IOP3 = (1 << 3), 145 MVS_IRQ_COM_OUT_I2O_HOS0 = (1 << 4), 146 MVS_IRQ_COM_OUT_I2O_HOS1 = (1 << 5), 147 MVS_IRQ_COM_OUT_I2O_HOS2 = (1 << 6), 148 MVS_IRQ_COM_OUT_I2O_HOS3 = (1 << 7), 149 MVS_IRQ_PCIF_TO_CPU_DRBL0 = (1 << 8), 150 MVS_IRQ_PCIF_TO_CPU_DRBL1 = (1 << 9), 151 MVS_IRQ_PCIF_TO_CPU_DRBL2 = (1 << 10), 152 MVS_IRQ_PCIF_TO_CPU_DRBL3 = (1 << 11), 153 MVS_IRQ_PCIF_DRBL0 = (1 << 12), 154 MVS_IRQ_PCIF_DRBL1 = (1 << 13), 155 MVS_IRQ_PCIF_DRBL2 = (1 << 14), 156 MVS_IRQ_PCIF_DRBL3 = (1 << 15), 157 MVS_IRQ_XOR_A = (1 << 16), 158 MVS_IRQ_XOR_B = (1 << 17), 159 MVS_IRQ_SAS_A = (1 << 18), 160 MVS_IRQ_SAS_B = (1 << 19), 161 MVS_IRQ_CPU_CNTRL = (1 << 20), 162 MVS_IRQ_GPIO = (1 << 21), 163 MVS_IRQ_UART = (1 << 22), 164 MVS_IRQ_SPI = (1 << 23), 165 MVS_IRQ_I2C = (1 << 24), 166 MVS_IRQ_SGPIO = (1 << 25), 167 MVS_IRQ_COM_ERR = (1 << 29), 168 MVS_IRQ_I2O_ERR = (1 << 30), 169 MVS_IRQ_PCIE_ERR = (1 << 31), 170}; 171 172union reg_phy_cfg { 173 u32 v; 174 struct { 175 u32 phy_reset:1; 176 u32 sas_support:1; 177 u32 sata_support:1; 178 u32 sata_host_mode:1; 179 /* 180 * bit 2: 6Gbps support 181 * bit 1: 3Gbps support 182 * bit 0: 1.5Gbps support 183 */ 184 u32 speed_support:3; 185 u32 snw_3_support:1; 186 u32 tx_lnk_parity:1; 187 /* 188 * bit 5: G1 (1.5Gbps) Without SSC 189 * bit 4: G1 (1.5Gbps) with SSC 190 * bit 3: G2 (3.0Gbps) Without SSC 191 * bit 2: G2 (3.0Gbps) with SSC 192 * bit 1: G3 (6.0Gbps) without SSC 193 * bit 0: G3 (6.0Gbps) with SSC 194 */ 195 u32 tx_spt_phs_lnk_rate:6; 196 /* 8h: 1.5Gbps 9h: 3Gbps Ah: 6Gbps */ 197 u32 tx_lgcl_lnk_rate:4; 198 u32 tx_ssc_type:1; 199 u32 sata_spin_up_spt:1; 200 u32 sata_spin_up_en:1; 201 u32 bypass_oob:1; 202 u32 disable_phy:1; 203 u32 rsvd:8; 204 } u; 205}; 206 207#define MAX_SG_ENTRY 255 208 209struct mvs_prd_imt { 210#ifndef __BIG_ENDIAN 211 __le32 len:22; 212 u8 _r_a:2; 213 u8 misc_ctl:4; 214 u8 inter_sel:4; 215#else 216 u32 inter_sel:4; 217 u32 misc_ctl:4; 218 u32 _r_a:2; 219 u32 len:22; 220#endif 221}; 222 223struct mvs_prd { 224 /* 64-bit buffer address */ 225 __le64 addr; 226 /* 22-bit length */ 227 __le32 im_len; 228} __attribute__ ((packed)); 229 230enum sgpio_registers { 231 MVS_SGPIO_HOST_OFFSET = 0x100, /* offset between hosts */ 232 233 MVS_SGPIO_CFG0 = 0xc200, 234 MVS_SGPIO_CFG0_ENABLE = (1 << 0), /* enable pins */ 235 MVS_SGPIO_CFG0_BLINKB = (1 << 1), /* blink generators */ 236 MVS_SGPIO_CFG0_BLINKA = (1 << 2), 237 MVS_SGPIO_CFG0_INVSCLK = (1 << 3), /* invert signal? */ 238 MVS_SGPIO_CFG0_INVSLOAD = (1 << 4), 239 MVS_SGPIO_CFG0_INVSDOUT = (1 << 5), 240 MVS_SGPIO_CFG0_SLOAD_FALLEDGE = (1 << 6), /* rise/fall edge? */ 241 MVS_SGPIO_CFG0_SDOUT_FALLEDGE = (1 << 7), 242 MVS_SGPIO_CFG0_SDIN_RISEEDGE = (1 << 8), 243 MVS_SGPIO_CFG0_MAN_BITLEN_SHIFT = 18, /* bits/frame manual mode */ 244 MVS_SGPIO_CFG0_AUT_BITLEN_SHIFT = 24, /* bits/frame auto mode */ 245 246 MVS_SGPIO_CFG1 = 0xc204, /* blink timing register */ 247 MVS_SGPIO_CFG1_LOWA_SHIFT = 0, /* A off time */ 248 MVS_SGPIO_CFG1_HIA_SHIFT = 4, /* A on time */ 249 MVS_SGPIO_CFG1_LOWB_SHIFT = 8, /* B off time */ 250 MVS_SGPIO_CFG1_HIB_SHIFT = 12, /* B on time */ 251 MVS_SGPIO_CFG1_MAXACTON_SHIFT = 16, /* max activity on time */ 252 253 /* force activity off time */ 254 MVS_SGPIO_CFG1_FORCEACTOFF_SHIFT = 20, 255 /* stretch activity on time */ 256 MVS_SGPIO_CFG1_STRCHACTON_SHIFT = 24, 257 /* stretch activiity off time */ 258 MVS_SGPIO_CFG1_STRCHACTOFF_SHIFT = 28, 259 260 261 MVS_SGPIO_CFG2 = 0xc208, /* clock speed register */ 262 MVS_SGPIO_CFG2_CLK_SHIFT = 0, 263 MVS_SGPIO_CFG2_BLINK_SHIFT = 20, 264 265 MVS_SGPIO_CTRL = 0xc20c, /* SDOUT/SDIN mode control */ 266 MVS_SGPIO_CTRL_SDOUT_AUTO = 2, 267 MVS_SGPIO_CTRL_SDOUT_SHIFT = 2, 268 269 MVS_SGPIO_DSRC = 0xc220, /* map ODn bits to drives */ 270 271 MVS_SGPIO_DCTRL = 0xc238, 272 MVS_SGPIO_DCTRL_ERR_SHIFT = 0, 273 MVS_SGPIO_DCTRL_LOC_SHIFT = 3, 274 MVS_SGPIO_DCTRL_ACT_SHIFT = 5, 275}; 276 277enum sgpio_led_status { 278 LED_OFF = 0, 279 LED_ON = 1, 280 LED_BLINKA = 2, 281 LED_BLINKA_INV = 3, 282 LED_BLINKA_SOF = 4, 283 LED_BLINKA_EOF = 5, 284 LED_BLINKB = 6, 285 LED_BLINKB_INV = 7, 286}; 287 288#define DEFAULT_SGPIO_BITS ((LED_BLINKA_SOF << \ 289 MVS_SGPIO_DCTRL_ACT_SHIFT) << (8 * 3) | \ 290 (LED_BLINKA_SOF << \ 291 MVS_SGPIO_DCTRL_ACT_SHIFT) << (8 * 2) | \ 292 (LED_BLINKA_SOF << \ 293 MVS_SGPIO_DCTRL_ACT_SHIFT) << (8 * 1) | \ 294 (LED_BLINKA_SOF << \ 295 MVS_SGPIO_DCTRL_ACT_SHIFT) << (8 * 0)) 296 297/* 298 * these registers are accessed through port vendor 299 * specific address/data registers 300 */ 301enum sas_sata_phy_regs { 302 GENERATION_1_SETTING = 0x118, 303 GENERATION_1_2_SETTING = 0x11C, 304 GENERATION_2_3_SETTING = 0x120, 305 GENERATION_3_4_SETTING = 0x124, 306}; 307 308#define SPI_CTRL_REG_94XX 0xc800 309#define SPI_ADDR_REG_94XX 0xc804 310#define SPI_WR_DATA_REG_94XX 0xc808 311#define SPI_RD_DATA_REG_94XX 0xc80c 312#define SPI_CTRL_READ_94XX (1U << 2) 313#define SPI_ADDR_VLD_94XX (1U << 1) 314#define SPI_CTRL_SpiStart_94XX (1U << 0) 315 316static inline int 317mv_ffc64(u64 v) 318{ 319 u64 x = ~v; 320 return x ? __ffs64(x) : -1; 321} 322 323#define r_reg_set_enable(i) \ 324 (((i) > 31) ? mr32(MVS_STP_REG_SET_1) : \ 325 mr32(MVS_STP_REG_SET_0)) 326 327#define w_reg_set_enable(i, tmp) \ 328 (((i) > 31) ? mw32(MVS_STP_REG_SET_1, tmp) : \ 329 mw32(MVS_STP_REG_SET_0, tmp)) 330 331extern const struct mvs_dispatch mvs_94xx_dispatch; 332#endif 333