pm8001_defs.h (4342B)
1/* 2 * PMC-Sierra 8001/8081/8088/8089 SAS/SATA based host adapters driver 3 * 4 * Copyright (c) 2008-2009 USI Co., Ltd. 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions, and the following disclaimer, 12 * without modification. 13 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 14 * substantially similar to the "NO WARRANTY" disclaimer below 15 * ("Disclaimer") and any redistribution must be conditioned upon 16 * including a substantially similar Disclaimer requirement for further 17 * binary redistribution. 18 * 3. Neither the names of the above-listed copyright holders nor the names 19 * of any contributors may be used to endorse or promote products derived 20 * from this software without specific prior written permission. 21 * 22 * Alternatively, this software may be distributed under the terms of the 23 * GNU General Public License ("GPL") version 2 as published by the Free 24 * Software Foundation. 25 * 26 * NO WARRANTY 27 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 28 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 29 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 30 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 31 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 32 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 33 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 34 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 35 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 36 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 37 * POSSIBILITY OF SUCH DAMAGES. 38 * 39 */ 40 41#ifndef _PM8001_DEFS_H_ 42#define _PM8001_DEFS_H_ 43 44enum chip_flavors { 45 chip_8001, 46 chip_8008, 47 chip_8009, 48 chip_8018, 49 chip_8019, 50 chip_8074, 51 chip_8076, 52 chip_8077, 53 chip_8006, 54 chip_8070, 55 chip_8072 56}; 57 58enum phy_speed { 59 PHY_SPEED_15 = 0x01, 60 PHY_SPEED_30 = 0x02, 61 PHY_SPEED_60 = 0x04, 62 PHY_SPEED_120 = 0x08, 63}; 64 65enum data_direction { 66 DATA_DIR_NONE = 0x0, /* NO TRANSFER */ 67 DATA_DIR_IN = 0x01, /* INBOUND */ 68 DATA_DIR_OUT = 0x02, /* OUTBOUND */ 69 DATA_DIR_BYRECIPIENT = 0x04, /* UNSPECIFIED */ 70}; 71 72enum port_type { 73 PORT_TYPE_SAS = (1L << 1), 74 PORT_TYPE_SATA = (1L << 0), 75}; 76 77/* driver compile-time configuration */ 78#define PM8001_MAX_CCB 1024 /* max ccbs supported */ 79#define PM8001_MPI_QUEUE 1024 /* maximum mpi queue entries */ 80#define PM8001_MAX_INB_NUM 64 81#define PM8001_MAX_OUTB_NUM 64 82#define PM8001_CAN_QUEUE 508 /* SCSI Queue depth */ 83 84/* Inbound/Outbound queue size */ 85#define IOMB_SIZE_SPC 64 86#define IOMB_SIZE_SPCV 128 87 88/* unchangeable hardware details */ 89#define PM8001_MAX_PHYS 16 /* max. possible phys */ 90#define PM8001_MAX_PORTS 16 /* max. possible ports */ 91#define PM8001_MAX_DEVICES 2048 /* max supported device */ 92#define PM8001_MAX_MSIX_VEC 64 /* max msi-x int for spcv/ve */ 93#define PM8001_RESERVE_SLOT 8 94 95#define CONFIG_SCSI_PM8001_MAX_DMA_SG 528 96#define PM8001_MAX_DMA_SG CONFIG_SCSI_PM8001_MAX_DMA_SG 97 98enum memory_region_num { 99 AAP1 = 0x0, /* application acceleration processor */ 100 IOP, /* IO processor */ 101 NVMD, /* NVM device */ 102 FW_FLASH, /* memory for fw flash update */ 103 FORENSIC_MEM, /* memory for fw forensic data */ 104 USI_MAX_MEMCNT_BASE 105}; 106#define PM8001_EVENT_LOG_SIZE (128 * 1024) 107 108/** 109 * maximum DMA memory regions(number of IBQ + number of IBQ CI 110 * + number of OBQ + number of OBQ PI) 111 */ 112#define USI_MAX_MEMCNT (USI_MAX_MEMCNT_BASE + ((2 * PM8001_MAX_INB_NUM) \ 113 + (2 * PM8001_MAX_OUTB_NUM))) 114/*error code*/ 115enum mpi_err { 116 MPI_IO_STATUS_SUCCESS = 0x0, 117 MPI_IO_STATUS_BUSY = 0x01, 118 MPI_IO_STATUS_FAIL = 0x02, 119}; 120 121/** 122 * Phy Control constants 123 */ 124enum phy_control_type { 125 PHY_LINK_RESET = 0x01, 126 PHY_HARD_RESET = 0x02, 127 PHY_NOTIFY_ENABLE_SPINUP = 0x10, 128}; 129 130enum pm8001_hba_info_flags { 131 PM8001F_INIT_TIME = (1U << 0), 132 PM8001F_RUN_TIME = (1U << 1), 133}; 134 135/** 136 * Phy Status 137 */ 138#define PHY_LINK_DISABLE 0x00 139#define PHY_LINK_DOWN 0x01 140#define PHY_STATE_LINK_UP_SPCV 0x2 141#define PHY_STATE_LINK_UP_SPC 0x1 142 143#endif