sym_defs.h (26469B)
1/* SPDX-License-Identifier: GPL-2.0-or-later */ 2/* 3 * Device driver for the SYMBIOS/LSILOGIC 53C8XX and 53C1010 family 4 * of PCI-SCSI IO processors. 5 * 6 * Copyright (C) 1999-2001 Gerard Roudier <groudier@free.fr> 7 * 8 * This driver is derived from the Linux sym53c8xx driver. 9 * Copyright (C) 1998-2000 Gerard Roudier 10 * 11 * The sym53c8xx driver is derived from the ncr53c8xx driver that had been 12 * a port of the FreeBSD ncr driver to Linux-1.2.13. 13 * 14 * The original ncr driver has been written for 386bsd and FreeBSD by 15 * Wolfgang Stanglmeier <wolf@cologne.de> 16 * Stefan Esser <se@mi.Uni-Koeln.de> 17 * Copyright (C) 1994 Wolfgang Stanglmeier 18 * 19 * Other major contributions: 20 * 21 * NVRAM detection and reading. 22 * Copyright (C) 1997 Richard Waltham <dormouse@farsrobt.demon.co.uk> 23 * 24 *----------------------------------------------------------------------------- 25 */ 26 27#ifndef SYM_DEFS_H 28#define SYM_DEFS_H 29 30#define SYM_VERSION "2.2.3" 31#define SYM_DRIVER_NAME "sym-" SYM_VERSION 32 33/* 34 * SYM53C8XX device features descriptor. 35 */ 36struct sym_chip { 37 u_short device_id; 38 u_short revision_id; 39 char *name; 40 u_char burst_max; /* log-base-2 of max burst */ 41 u_char offset_max; 42 u_char nr_divisor; 43 u_char lp_probe_bit; 44 u_int features; 45#define FE_LED0 (1<<0) 46#define FE_WIDE (1<<1) /* Wide data transfers */ 47#define FE_ULTRA (1<<2) /* Ultra speed 20Mtrans/sec */ 48#define FE_ULTRA2 (1<<3) /* Ultra 2 - 40 Mtrans/sec */ 49#define FE_DBLR (1<<4) /* Clock doubler present */ 50#define FE_QUAD (1<<5) /* Clock quadrupler present */ 51#define FE_ERL (1<<6) /* Enable read line */ 52#define FE_CLSE (1<<7) /* Cache line size enable */ 53#define FE_WRIE (1<<8) /* Write & Invalidate enable */ 54#define FE_ERMP (1<<9) /* Enable read multiple */ 55#define FE_BOF (1<<10) /* Burst opcode fetch */ 56#define FE_DFS (1<<11) /* DMA fifo size */ 57#define FE_PFEN (1<<12) /* Prefetch enable */ 58#define FE_LDSTR (1<<13) /* Load/Store supported */ 59#define FE_RAM (1<<14) /* On chip RAM present */ 60#define FE_VARCLK (1<<15) /* Clock frequency may vary */ 61#define FE_RAM8K (1<<16) /* On chip RAM sized 8Kb */ 62#define FE_64BIT (1<<17) /* 64-bit PCI BUS interface */ 63#define FE_IO256 (1<<18) /* Requires full 256 bytes in PCI space */ 64#define FE_NOPM (1<<19) /* Scripts handles phase mismatch */ 65#define FE_LEDC (1<<20) /* Hardware control of LED */ 66#define FE_ULTRA3 (1<<21) /* Ultra 3 - 80 Mtrans/sec DT */ 67#define FE_66MHZ (1<<22) /* 66MHz PCI support */ 68#define FE_CRC (1<<23) /* CRC support */ 69#define FE_DIFF (1<<24) /* SCSI HVD support */ 70#define FE_DFBC (1<<25) /* Have DFBC register */ 71#define FE_LCKFRQ (1<<26) /* Have LCKFRQ */ 72#define FE_C10 (1<<27) /* Various C10 core (mis)features */ 73#define FE_U3EN (1<<28) /* U3EN bit usable */ 74#define FE_DAC (1<<29) /* Support PCI DAC (64 bit addressing) */ 75#define FE_ISTAT1 (1<<30) /* Have ISTAT1, MBOX0, MBOX1 registers */ 76 77#define FE_CACHE_SET (FE_ERL|FE_CLSE|FE_WRIE|FE_ERMP) 78#define FE_CACHE0_SET (FE_CACHE_SET & ~FE_ERL) 79}; 80 81/* 82 * SYM53C8XX IO register data structure. 83 */ 84struct sym_reg { 85/*00*/ u8 nc_scntl0; /* full arb., ena parity, par->ATN */ 86 87/*01*/ u8 nc_scntl1; /* no reset */ 88 #define ISCON 0x10 /* connected to scsi */ 89 #define CRST 0x08 /* force reset */ 90 #define IARB 0x02 /* immediate arbitration */ 91 92/*02*/ u8 nc_scntl2; /* no disconnect expected */ 93 #define SDU 0x80 /* cmd: disconnect will raise error */ 94 #define CHM 0x40 /* sta: chained mode */ 95 #define WSS 0x08 /* sta: wide scsi send [W]*/ 96 #define WSR 0x01 /* sta: wide scsi received [W]*/ 97 98/*03*/ u8 nc_scntl3; /* cnf system clock dependent */ 99 #define EWS 0x08 /* cmd: enable wide scsi [W]*/ 100 #define ULTRA 0x80 /* cmd: ULTRA enable */ 101 /* bits 0-2, 7 rsvd for C1010 */ 102 103/*04*/ u8 nc_scid; /* cnf host adapter scsi address */ 104 #define RRE 0x40 /* r/w:e enable response to resel. */ 105 #define SRE 0x20 /* r/w:e enable response to select */ 106 107/*05*/ u8 nc_sxfer; /* ### Sync speed and count */ 108 /* bits 6-7 rsvd for C1010 */ 109 110/*06*/ u8 nc_sdid; /* ### Destination-ID */ 111 112/*07*/ u8 nc_gpreg; /* ??? IO-Pins */ 113 114/*08*/ u8 nc_sfbr; /* ### First byte received */ 115 116/*09*/ u8 nc_socl; 117 #define CREQ 0x80 /* r/w: SCSI-REQ */ 118 #define CACK 0x40 /* r/w: SCSI-ACK */ 119 #define CBSY 0x20 /* r/w: SCSI-BSY */ 120 #define CSEL 0x10 /* r/w: SCSI-SEL */ 121 #define CATN 0x08 /* r/w: SCSI-ATN */ 122 #define CMSG 0x04 /* r/w: SCSI-MSG */ 123 #define CC_D 0x02 /* r/w: SCSI-C_D */ 124 #define CI_O 0x01 /* r/w: SCSI-I_O */ 125 126/*0a*/ u8 nc_ssid; 127 128/*0b*/ u8 nc_sbcl; 129 130/*0c*/ u8 nc_dstat; 131 #define DFE 0x80 /* sta: dma fifo empty */ 132 #define MDPE 0x40 /* int: master data parity error */ 133 #define BF 0x20 /* int: script: bus fault */ 134 #define ABRT 0x10 /* int: script: command aborted */ 135 #define SSI 0x08 /* int: script: single step */ 136 #define SIR 0x04 /* int: script: interrupt instruct. */ 137 #define IID 0x01 /* int: script: illegal instruct. */ 138 139/*0d*/ u8 nc_sstat0; 140 #define ILF 0x80 /* sta: data in SIDL register lsb */ 141 #define ORF 0x40 /* sta: data in SODR register lsb */ 142 #define OLF 0x20 /* sta: data in SODL register lsb */ 143 #define AIP 0x10 /* sta: arbitration in progress */ 144 #define LOA 0x08 /* sta: arbitration lost */ 145 #define WOA 0x04 /* sta: arbitration won */ 146 #define IRST 0x02 /* sta: scsi reset signal */ 147 #define SDP 0x01 /* sta: scsi parity signal */ 148 149/*0e*/ u8 nc_sstat1; 150 #define FF3210 0xf0 /* sta: bytes in the scsi fifo */ 151 152/*0f*/ u8 nc_sstat2; 153 #define ILF1 0x80 /* sta: data in SIDL register msb[W]*/ 154 #define ORF1 0x40 /* sta: data in SODR register msb[W]*/ 155 #define OLF1 0x20 /* sta: data in SODL register msb[W]*/ 156 #define DM 0x04 /* sta: DIFFSENS mismatch (895/6 only) */ 157 #define LDSC 0x02 /* sta: disconnect & reconnect */ 158 159/*10*/ u8 nc_dsa; /* --> Base page */ 160/*11*/ u8 nc_dsa1; 161/*12*/ u8 nc_dsa2; 162/*13*/ u8 nc_dsa3; 163 164/*14*/ u8 nc_istat; /* --> Main Command and status */ 165 #define CABRT 0x80 /* cmd: abort current operation */ 166 #define SRST 0x40 /* mod: reset chip */ 167 #define SIGP 0x20 /* r/w: message from host to script */ 168 #define SEM 0x10 /* r/w: message between host + script */ 169 #define CON 0x08 /* sta: connected to scsi */ 170 #define INTF 0x04 /* sta: int on the fly (reset by wr)*/ 171 #define SIP 0x02 /* sta: scsi-interrupt */ 172 #define DIP 0x01 /* sta: host/script interrupt */ 173 174/*15*/ u8 nc_istat1; /* 896 only */ 175 #define FLSH 0x04 /* sta: chip is flushing */ 176 #define SCRUN 0x02 /* sta: scripts are running */ 177 #define SIRQD 0x01 /* r/w: disable INT pin */ 178 179/*16*/ u8 nc_mbox0; /* 896 only */ 180/*17*/ u8 nc_mbox1; /* 896 only */ 181 182/*18*/ u8 nc_ctest0; 183/*19*/ u8 nc_ctest1; 184 185/*1a*/ u8 nc_ctest2; 186 #define CSIGP 0x40 187 /* bits 0-2,7 rsvd for C1010 */ 188 189/*1b*/ u8 nc_ctest3; 190 #define FLF 0x08 /* cmd: flush dma fifo */ 191 #define CLF 0x04 /* cmd: clear dma fifo */ 192 #define FM 0x02 /* mod: fetch pin mode */ 193 #define WRIE 0x01 /* mod: write and invalidate enable */ 194 /* bits 4-7 rsvd for C1010 */ 195 196/*1c*/ u32 nc_temp; /* ### Temporary stack */ 197 198/*20*/ u8 nc_dfifo; 199/*21*/ u8 nc_ctest4; 200 #define BDIS 0x80 /* mod: burst disable */ 201 #define MPEE 0x08 /* mod: master parity error enable */ 202 203/*22*/ u8 nc_ctest5; 204 #define DFS 0x20 /* mod: dma fifo size */ 205 /* bits 0-1, 3-7 rsvd for C1010 */ 206 207/*23*/ u8 nc_ctest6; 208 209/*24*/ u32 nc_dbc; /* ### Byte count and command */ 210/*28*/ u32 nc_dnad; /* ### Next command register */ 211/*2c*/ u32 nc_dsp; /* --> Script Pointer */ 212/*30*/ u32 nc_dsps; /* --> Script pointer save/opcode#2 */ 213 214/*34*/ u8 nc_scratcha; /* Temporary register a */ 215/*35*/ u8 nc_scratcha1; 216/*36*/ u8 nc_scratcha2; 217/*37*/ u8 nc_scratcha3; 218 219/*38*/ u8 nc_dmode; 220 #define BL_2 0x80 /* mod: burst length shift value +2 */ 221 #define BL_1 0x40 /* mod: burst length shift value +1 */ 222 #define ERL 0x08 /* mod: enable read line */ 223 #define ERMP 0x04 /* mod: enable read multiple */ 224 #define BOF 0x02 /* mod: burst op code fetch */ 225 226/*39*/ u8 nc_dien; 227/*3a*/ u8 nc_sbr; 228 229/*3b*/ u8 nc_dcntl; /* --> Script execution control */ 230 #define CLSE 0x80 /* mod: cache line size enable */ 231 #define PFF 0x40 /* cmd: pre-fetch flush */ 232 #define PFEN 0x20 /* mod: pre-fetch enable */ 233 #define SSM 0x10 /* mod: single step mode */ 234 #define IRQM 0x08 /* mod: irq mode (1 = totem pole !) */ 235 #define STD 0x04 /* cmd: start dma mode */ 236 #define IRQD 0x02 /* mod: irq disable */ 237 #define NOCOM 0x01 /* cmd: protect sfbr while reselect */ 238 /* bits 0-1 rsvd for C1010 */ 239 240/*3c*/ u32 nc_adder; 241 242/*40*/ u16 nc_sien; /* -->: interrupt enable */ 243/*42*/ u16 nc_sist; /* <--: interrupt status */ 244 #define SBMC 0x1000/* sta: SCSI Bus Mode Change (895/6 only) */ 245 #define STO 0x0400/* sta: timeout (select) */ 246 #define GEN 0x0200/* sta: timeout (general) */ 247 #define HTH 0x0100/* sta: timeout (handshake) */ 248 #define MA 0x80 /* sta: phase mismatch */ 249 #define CMP 0x40 /* sta: arbitration complete */ 250 #define SEL 0x20 /* sta: selected by another device */ 251 #define RSL 0x10 /* sta: reselected by another device*/ 252 #define SGE 0x08 /* sta: gross error (over/underflow)*/ 253 #define UDC 0x04 /* sta: unexpected disconnect */ 254 #define RST 0x02 /* sta: scsi bus reset detected */ 255 #define PAR 0x01 /* sta: scsi parity error */ 256 257/*44*/ u8 nc_slpar; 258/*45*/ u8 nc_swide; 259/*46*/ u8 nc_macntl; 260/*47*/ u8 nc_gpcntl; 261/*48*/ u8 nc_stime0; /* cmd: timeout for select&handshake*/ 262/*49*/ u8 nc_stime1; /* cmd: timeout user defined */ 263/*4a*/ u16 nc_respid; /* sta: Reselect-IDs */ 264 265/*4c*/ u8 nc_stest0; 266 267/*4d*/ u8 nc_stest1; 268 #define SCLK 0x80 /* Use the PCI clock as SCSI clock */ 269 #define DBLEN 0x08 /* clock doubler running */ 270 #define DBLSEL 0x04 /* clock doubler selected */ 271 272 273/*4e*/ u8 nc_stest2; 274 #define ROF 0x40 /* reset scsi offset (after gross error!) */ 275 #define EXT 0x02 /* extended filtering */ 276 277/*4f*/ u8 nc_stest3; 278 #define TE 0x80 /* c: tolerAnt enable */ 279 #define HSC 0x20 /* c: Halt SCSI Clock */ 280 #define CSF 0x02 /* c: clear scsi fifo */ 281 282/*50*/ u16 nc_sidl; /* Lowlevel: latched from scsi data */ 283/*52*/ u8 nc_stest4; 284 #define SMODE 0xc0 /* SCSI bus mode (895/6 only) */ 285 #define SMODE_HVD 0x40 /* High Voltage Differential */ 286 #define SMODE_SE 0x80 /* Single Ended */ 287 #define SMODE_LVD 0xc0 /* Low Voltage Differential */ 288 #define LCKFRQ 0x20 /* Frequency Lock (895/6 only) */ 289 /* bits 0-5 rsvd for C1010 */ 290 291/*53*/ u8 nc_53_; 292/*54*/ u16 nc_sodl; /* Lowlevel: data out to scsi data */ 293/*56*/ u8 nc_ccntl0; /* Chip Control 0 (896) */ 294 #define ENPMJ 0x80 /* Enable Phase Mismatch Jump */ 295 #define PMJCTL 0x40 /* Phase Mismatch Jump Control */ 296 #define ENNDJ 0x20 /* Enable Non Data PM Jump */ 297 #define DISFC 0x10 /* Disable Auto FIFO Clear */ 298 #define DILS 0x02 /* Disable Internal Load/Store */ 299 #define DPR 0x01 /* Disable Pipe Req */ 300 301/*57*/ u8 nc_ccntl1; /* Chip Control 1 (896) */ 302 #define ZMOD 0x80 /* High Impedance Mode */ 303 #define DDAC 0x08 /* Disable Dual Address Cycle */ 304 #define XTIMOD 0x04 /* 64-bit Table Ind. Indexing Mode */ 305 #define EXTIBMV 0x02 /* Enable 64-bit Table Ind. BMOV */ 306 #define EXDBMV 0x01 /* Enable 64-bit Direct BMOV */ 307 308/*58*/ u16 nc_sbdl; /* Lowlevel: data from scsi data */ 309/*5a*/ u16 nc_5a_; 310 311/*5c*/ u8 nc_scr0; /* Working register B */ 312/*5d*/ u8 nc_scr1; 313/*5e*/ u8 nc_scr2; 314/*5f*/ u8 nc_scr3; 315 316/*60*/ u8 nc_scrx[64]; /* Working register C-R */ 317/*a0*/ u32 nc_mmrs; /* Memory Move Read Selector */ 318/*a4*/ u32 nc_mmws; /* Memory Move Write Selector */ 319/*a8*/ u32 nc_sfs; /* Script Fetch Selector */ 320/*ac*/ u32 nc_drs; /* DSA Relative Selector */ 321/*b0*/ u32 nc_sbms; /* Static Block Move Selector */ 322/*b4*/ u32 nc_dbms; /* Dynamic Block Move Selector */ 323/*b8*/ u32 nc_dnad64; /* DMA Next Address 64 */ 324/*bc*/ u16 nc_scntl4; /* C1010 only */ 325 #define U3EN 0x80 /* Enable Ultra 3 */ 326 #define AIPCKEN 0x40 /* AIP checking enable */ 327 /* Also enable AIP generation on C10-33*/ 328 #define XCLKH_DT 0x08 /* Extra clock of data hold on DT edge */ 329 #define XCLKH_ST 0x04 /* Extra clock of data hold on ST edge */ 330 #define XCLKS_DT 0x02 /* Extra clock of data set on DT edge */ 331 #define XCLKS_ST 0x01 /* Extra clock of data set on ST edge */ 332/*be*/ u8 nc_aipcntl0; /* AIP Control 0 C1010 only */ 333/*bf*/ u8 nc_aipcntl1; /* AIP Control 1 C1010 only */ 334 #define DISAIP 0x08 /* Disable AIP generation C10-66 only */ 335/*c0*/ u32 nc_pmjad1; /* Phase Mismatch Jump Address 1 */ 336/*c4*/ u32 nc_pmjad2; /* Phase Mismatch Jump Address 2 */ 337/*c8*/ u8 nc_rbc; /* Remaining Byte Count */ 338/*c9*/ u8 nc_rbc1; 339/*ca*/ u8 nc_rbc2; 340/*cb*/ u8 nc_rbc3; 341 342/*cc*/ u8 nc_ua; /* Updated Address */ 343/*cd*/ u8 nc_ua1; 344/*ce*/ u8 nc_ua2; 345/*cf*/ u8 nc_ua3; 346/*d0*/ u32 nc_esa; /* Entry Storage Address */ 347/*d4*/ u8 nc_ia; /* Instruction Address */ 348/*d5*/ u8 nc_ia1; 349/*d6*/ u8 nc_ia2; 350/*d7*/ u8 nc_ia3; 351/*d8*/ u32 nc_sbc; /* SCSI Byte Count (3 bytes only) */ 352/*dc*/ u32 nc_csbc; /* Cumulative SCSI Byte Count */ 353 /* Following for C1010 only */ 354/*e0*/ u16 nc_crcpad; /* CRC Value */ 355/*e2*/ u8 nc_crccntl0; /* CRC control register */ 356 #define SNDCRC 0x10 /* Send CRC Request */ 357/*e3*/ u8 nc_crccntl1; /* CRC control register */ 358/*e4*/ u32 nc_crcdata; /* CRC data register */ 359/*e8*/ u32 nc_e8_; 360/*ec*/ u32 nc_ec_; 361/*f0*/ u16 nc_dfbc; /* DMA FIFO byte count */ 362}; 363 364/*----------------------------------------------------------- 365 * 366 * Utility macros for the script. 367 * 368 *----------------------------------------------------------- 369 */ 370 371#define REGJ(p,r) (offsetof(struct sym_reg, p ## r)) 372#define REG(r) REGJ (nc_, r) 373 374/*----------------------------------------------------------- 375 * 376 * SCSI phases 377 * 378 *----------------------------------------------------------- 379 */ 380 381#define SCR_DATA_OUT 0x00000000 382#define SCR_DATA_IN 0x01000000 383#define SCR_COMMAND 0x02000000 384#define SCR_STATUS 0x03000000 385#define SCR_DT_DATA_OUT 0x04000000 386#define SCR_DT_DATA_IN 0x05000000 387#define SCR_MSG_OUT 0x06000000 388#define SCR_MSG_IN 0x07000000 389/* DT phases are illegal for non Ultra3 mode */ 390#define SCR_ILG_OUT 0x04000000 391#define SCR_ILG_IN 0x05000000 392 393/*----------------------------------------------------------- 394 * 395 * Data transfer via SCSI. 396 * 397 *----------------------------------------------------------- 398 * 399 * MOVE_ABS (LEN) 400 * <<start address>> 401 * 402 * MOVE_IND (LEN) 403 * <<dnad_offset>> 404 * 405 * MOVE_TBL 406 * <<dnad_offset>> 407 * 408 *----------------------------------------------------------- 409 */ 410 411#define OPC_MOVE 0x08000000 412 413#define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l)) 414/* #define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l)) */ 415#define SCR_MOVE_TBL (0x10000000 | OPC_MOVE) 416 417#define SCR_CHMOV_ABS(l) ((0x00000000) | (l)) 418/* #define SCR_CHMOV_IND(l) ((0x20000000) | (l)) */ 419#define SCR_CHMOV_TBL (0x10000000) 420 421#ifdef SYM_CONF_TARGET_ROLE_SUPPORT 422/* We steal the `indirect addressing' flag for target mode MOVE in scripts */ 423 424#define OPC_TCHMOVE 0x08000000 425 426#define SCR_TCHMOVE_ABS(l) ((0x20000000 | OPC_TCHMOVE) | (l)) 427#define SCR_TCHMOVE_TBL (0x30000000 | OPC_TCHMOVE) 428 429#define SCR_TMOV_ABS(l) ((0x20000000) | (l)) 430#define SCR_TMOV_TBL (0x30000000) 431#endif 432 433struct sym_tblmove { 434 u32 size; 435 u32 addr; 436}; 437 438/*----------------------------------------------------------- 439 * 440 * Selection 441 * 442 *----------------------------------------------------------- 443 * 444 * SEL_ABS | SCR_ID (0..15) [ | REL_JMP] 445 * <<alternate_address>> 446 * 447 * SEL_TBL | << dnad_offset>> [ | REL_JMP] 448 * <<alternate_address>> 449 * 450 *----------------------------------------------------------- 451 */ 452 453#define SCR_SEL_ABS 0x40000000 454#define SCR_SEL_ABS_ATN 0x41000000 455#define SCR_SEL_TBL 0x42000000 456#define SCR_SEL_TBL_ATN 0x43000000 457 458#ifdef SYM_CONF_TARGET_ROLE_SUPPORT 459#define SCR_RESEL_ABS 0x40000000 460#define SCR_RESEL_ABS_ATN 0x41000000 461#define SCR_RESEL_TBL 0x42000000 462#define SCR_RESEL_TBL_ATN 0x43000000 463#endif 464 465struct sym_tblsel { 466 u_char sel_scntl4; /* C1010 only */ 467 u_char sel_sxfer; 468 u_char sel_id; 469 u_char sel_scntl3; 470}; 471 472#define SCR_JMP_REL 0x04000000 473#define SCR_ID(id) (((u32)(id)) << 16) 474 475/*----------------------------------------------------------- 476 * 477 * Waiting for Disconnect or Reselect 478 * 479 *----------------------------------------------------------- 480 * 481 * WAIT_DISC 482 * dummy: <<alternate_address>> 483 * 484 * WAIT_RESEL 485 * <<alternate_address>> 486 * 487 *----------------------------------------------------------- 488 */ 489 490#define SCR_WAIT_DISC 0x48000000 491#define SCR_WAIT_RESEL 0x50000000 492 493#ifdef SYM_CONF_TARGET_ROLE_SUPPORT 494#define SCR_DISCONNECT 0x48000000 495#endif 496 497/*----------------------------------------------------------- 498 * 499 * Bit Set / Reset 500 * 501 *----------------------------------------------------------- 502 * 503 * SET (flags {|.. }) 504 * 505 * CLR (flags {|.. }) 506 * 507 *----------------------------------------------------------- 508 */ 509 510#define SCR_SET(f) (0x58000000 | (f)) 511#define SCR_CLR(f) (0x60000000 | (f)) 512 513#define SCR_CARRY 0x00000400 514#define SCR_TRG 0x00000200 515#define SCR_ACK 0x00000040 516#define SCR_ATN 0x00000008 517 518 519/*----------------------------------------------------------- 520 * 521 * Memory to memory move 522 * 523 *----------------------------------------------------------- 524 * 525 * COPY (bytecount) 526 * << source_address >> 527 * << destination_address >> 528 * 529 * SCR_COPY sets the NO FLUSH option by default. 530 * SCR_COPY_F does not set this option. 531 * 532 * For chips which do not support this option, 533 * sym_fw_bind_script() will remove this bit. 534 * 535 *----------------------------------------------------------- 536 */ 537 538#define SCR_NO_FLUSH 0x01000000 539 540#define SCR_COPY(n) (0xc0000000 | SCR_NO_FLUSH | (n)) 541#define SCR_COPY_F(n) (0xc0000000 | (n)) 542 543/*----------------------------------------------------------- 544 * 545 * Register move and binary operations 546 * 547 *----------------------------------------------------------- 548 * 549 * SFBR_REG (reg, op, data) reg = SFBR op data 550 * << 0 >> 551 * 552 * REG_SFBR (reg, op, data) SFBR = reg op data 553 * << 0 >> 554 * 555 * REG_REG (reg, op, data) reg = reg op data 556 * << 0 >> 557 * 558 *----------------------------------------------------------- 559 * 560 * On 825A, 875, 895 and 896 chips the content 561 * of SFBR register can be used as data (SCR_SFBR_DATA). 562 * The 896 has additionnal IO registers starting at 563 * offset 0x80. Bit 7 of register offset is stored in 564 * bit 7 of the SCRIPTS instruction first DWORD. 565 * 566 *----------------------------------------------------------- 567 */ 568 569#define SCR_REG_OFS(ofs) ((((ofs) & 0x7f) << 16ul) + ((ofs) & 0x80)) 570 571#define SCR_SFBR_REG(reg,op,data) \ 572 (0x68000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) 573 574#define SCR_REG_SFBR(reg,op,data) \ 575 (0x70000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) 576 577#define SCR_REG_REG(reg,op,data) \ 578 (0x78000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) 579 580 581#define SCR_LOAD 0x00000000 582#define SCR_SHL 0x01000000 583#define SCR_OR 0x02000000 584#define SCR_XOR 0x03000000 585#define SCR_AND 0x04000000 586#define SCR_SHR 0x05000000 587#define SCR_ADD 0x06000000 588#define SCR_ADDC 0x07000000 589 590#define SCR_SFBR_DATA (0x00800000>>8ul) /* Use SFBR as data */ 591 592/*----------------------------------------------------------- 593 * 594 * FROM_REG (reg) SFBR = reg 595 * << 0 >> 596 * 597 * TO_REG (reg) reg = SFBR 598 * << 0 >> 599 * 600 * LOAD_REG (reg, data) reg = <data> 601 * << 0 >> 602 * 603 * LOAD_SFBR(data) SFBR = <data> 604 * << 0 >> 605 * 606 *----------------------------------------------------------- 607 */ 608 609#define SCR_FROM_REG(reg) \ 610 SCR_REG_SFBR(reg,SCR_OR,0) 611 612#define SCR_TO_REG(reg) \ 613 SCR_SFBR_REG(reg,SCR_OR,0) 614 615#define SCR_LOAD_REG(reg,data) \ 616 SCR_REG_REG(reg,SCR_LOAD,data) 617 618#define SCR_LOAD_SFBR(data) \ 619 (SCR_REG_SFBR (gpreg, SCR_LOAD, data)) 620 621/*----------------------------------------------------------- 622 * 623 * LOAD from memory to register. 624 * STORE from register to memory. 625 * 626 * Only supported by 810A, 860, 825A, 875, 895 and 896. 627 * 628 *----------------------------------------------------------- 629 * 630 * LOAD_ABS (LEN) 631 * <<start address>> 632 * 633 * LOAD_REL (LEN) (DSA relative) 634 * <<dsa_offset>> 635 * 636 *----------------------------------------------------------- 637 */ 638 639#define SCR_REG_OFS2(ofs) (((ofs) & 0xff) << 16ul) 640#define SCR_NO_FLUSH2 0x02000000 641#define SCR_DSA_REL2 0x10000000 642 643#define SCR_LOAD_R(reg, how, n) \ 644 (0xe1000000 | how | (SCR_REG_OFS2(REG(reg))) | (n)) 645 646#define SCR_STORE_R(reg, how, n) \ 647 (0xe0000000 | how | (SCR_REG_OFS2(REG(reg))) | (n)) 648 649#define SCR_LOAD_ABS(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2, n) 650#define SCR_LOAD_REL(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2, n) 651#define SCR_LOAD_ABS_F(reg, n) SCR_LOAD_R(reg, 0, n) 652#define SCR_LOAD_REL_F(reg, n) SCR_LOAD_R(reg, SCR_DSA_REL2, n) 653 654#define SCR_STORE_ABS(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2, n) 655#define SCR_STORE_REL(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2,n) 656#define SCR_STORE_ABS_F(reg, n) SCR_STORE_R(reg, 0, n) 657#define SCR_STORE_REL_F(reg, n) SCR_STORE_R(reg, SCR_DSA_REL2, n) 658 659 660/*----------------------------------------------------------- 661 * 662 * Waiting for Disconnect or Reselect 663 * 664 *----------------------------------------------------------- 665 * 666 * JUMP [ | IFTRUE/IFFALSE ( ... ) ] 667 * <<address>> 668 * 669 * JUMPR [ | IFTRUE/IFFALSE ( ... ) ] 670 * <<distance>> 671 * 672 * CALL [ | IFTRUE/IFFALSE ( ... ) ] 673 * <<address>> 674 * 675 * CALLR [ | IFTRUE/IFFALSE ( ... ) ] 676 * <<distance>> 677 * 678 * RETURN [ | IFTRUE/IFFALSE ( ... ) ] 679 * <<dummy>> 680 * 681 * INT [ | IFTRUE/IFFALSE ( ... ) ] 682 * <<ident>> 683 * 684 * INT_FLY [ | IFTRUE/IFFALSE ( ... ) ] 685 * <<ident>> 686 * 687 * Conditions: 688 * WHEN (phase) 689 * IF (phase) 690 * CARRYSET 691 * DATA (data, mask) 692 * 693 *----------------------------------------------------------- 694 */ 695 696#define SCR_NO_OP 0x80000000 697#define SCR_JUMP 0x80080000 698#define SCR_JUMP64 0x80480000 699#define SCR_JUMPR 0x80880000 700#define SCR_CALL 0x88080000 701#define SCR_CALLR 0x88880000 702#define SCR_RETURN 0x90080000 703#define SCR_INT 0x98080000 704#define SCR_INT_FLY 0x98180000 705 706#define IFFALSE(arg) (0x00080000 | (arg)) 707#define IFTRUE(arg) (0x00000000 | (arg)) 708 709#define WHEN(phase) (0x00030000 | (phase)) 710#define IF(phase) (0x00020000 | (phase)) 711 712#define DATA(D) (0x00040000 | ((D) & 0xff)) 713#define MASK(D,M) (0x00040000 | (((M ^ 0xff) & 0xff) << 8ul)|((D) & 0xff)) 714 715#define CARRYSET (0x00200000) 716 717/*----------------------------------------------------------- 718 * 719 * SCSI constants. 720 * 721 *----------------------------------------------------------- 722 */ 723 724/* 725 * Messages 726 */ 727 728#define M_COMPLETE COMMAND_COMPLETE 729#define M_EXTENDED EXTENDED_MESSAGE 730#define M_SAVE_DP SAVE_POINTERS 731#define M_RESTORE_DP RESTORE_POINTERS 732#define M_DISCONNECT DISCONNECT 733#define M_ID_ERROR INITIATOR_ERROR 734#define M_ABORT ABORT_TASK_SET 735#define M_REJECT MESSAGE_REJECT 736#define M_NOOP NOP 737#define M_PARITY MSG_PARITY_ERROR 738#define M_LCOMPLETE LINKED_CMD_COMPLETE 739#define M_FCOMPLETE LINKED_FLG_CMD_COMPLETE 740#define M_RESET TARGET_RESET 741#define M_ABORT_TAG ABORT_TASK 742#define M_CLEAR_QUEUE CLEAR_TASK_SET 743#define M_INIT_REC INITIATE_RECOVERY 744#define M_REL_REC RELEASE_RECOVERY 745#define M_TERMINATE (0x11) 746#define M_SIMPLE_TAG SIMPLE_QUEUE_TAG 747#define M_HEAD_TAG HEAD_OF_QUEUE_TAG 748#define M_ORDERED_TAG ORDERED_QUEUE_TAG 749#define M_IGN_RESIDUE IGNORE_WIDE_RESIDUE 750 751#define M_X_MODIFY_DP EXTENDED_MODIFY_DATA_POINTER 752#define M_X_SYNC_REQ EXTENDED_SDTR 753#define M_X_WIDE_REQ EXTENDED_WDTR 754#define M_X_PPR_REQ EXTENDED_PPR 755 756/* 757 * PPR protocol options 758 */ 759#define PPR_OPT_IU (0x01) 760#define PPR_OPT_DT (0x02) 761#define PPR_OPT_QAS (0x04) 762#define PPR_OPT_MASK (0x07) 763 764/* 765 * Status 766 */ 767 768#define S_GOOD SAM_STAT_GOOD 769#define S_CHECK_COND SAM_STAT_CHECK_CONDITION 770#define S_COND_MET SAM_STAT_CONDITION_MET 771#define S_BUSY SAM_STAT_BUSY 772#define S_INT SAM_STAT_INTERMEDIATE 773#define S_INT_COND_MET SAM_STAT_INTERMEDIATE_CONDITION_MET 774#define S_CONFLICT SAM_STAT_RESERVATION_CONFLICT 775#define S_TERMINATED SAM_STAT_COMMAND_TERMINATED 776#define S_QUEUE_FULL SAM_STAT_TASK_SET_FULL 777#define S_ILLEGAL (0xff) 778 779#endif /* defined SYM_DEFS_H */