sunzilog.h (9584B)
1/* SPDX-License-Identifier: GPL-2.0 */ 2#ifndef _SUNZILOG_H 3#define _SUNZILOG_H 4 5struct zilog_channel { 6 volatile unsigned char control; 7 volatile unsigned char __pad1; 8 volatile unsigned char data; 9 volatile unsigned char __pad2; 10}; 11 12struct zilog_layout { 13 struct zilog_channel channelB; 14 struct zilog_channel channelA; 15}; 16 17#define NUM_ZSREGS 17 18#define R7p 16 /* Written as R7 with P15 bit 0 set */ 19 20/* Conversion routines to/from brg time constants from/to bits 21 * per second. 22 */ 23#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2)) 24#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2) 25 26/* The Zilog register set */ 27 28#define FLAG 0x7e 29 30/* Write Register 0 */ 31#define R0 0 /* Register selects */ 32#define R1 1 33#define R2 2 34#define R3 3 35#define R4 4 36#define R5 5 37#define R6 6 38#define R7 7 39#define R8 8 40#define R9 9 41#define R10 10 42#define R11 11 43#define R12 12 44#define R13 13 45#define R14 14 46#define R15 15 47 48#define NULLCODE 0 /* Null Code */ 49#define POINT_HIGH 0x8 /* Select upper half of registers */ 50#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */ 51#define SEND_ABORT 0x18 /* HDLC Abort */ 52#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */ 53#define RES_Tx_P 0x28 /* Reset TxINT Pending */ 54#define ERR_RES 0x30 /* Error Reset */ 55#define RES_H_IUS 0x38 /* Reset highest IUS */ 56 57#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */ 58#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */ 59#define RES_EOM_L 0xC0 /* Reset EOM latch */ 60 61/* Write Register 1 */ 62 63#define EXT_INT_ENAB 0x1 /* Ext Int Enable */ 64#define TxINT_ENAB 0x2 /* Tx Int Enable */ 65#define PAR_SPEC 0x4 /* Parity is special condition */ 66 67#define RxINT_DISAB 0 /* Rx Int Disable */ 68#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */ 69#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */ 70#define INT_ERR_Rx 0x18 /* Int on error only */ 71#define RxINT_MASK 0x18 72 73#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */ 74#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */ 75#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */ 76 77/* Write Register #2 (Interrupt Vector) */ 78 79/* Write Register 3 */ 80 81#define RxENAB 0x1 /* Rx Enable */ 82#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */ 83#define ADD_SM 0x4 /* Address Search Mode (SDLC) */ 84#define RxCRC_ENAB 0x8 /* Rx CRC Enable */ 85#define ENT_HM 0x10 /* Enter Hunt Mode */ 86#define AUTO_ENAB 0x20 /* Auto Enables */ 87#define Rx5 0x0 /* Rx 5 Bits/Character */ 88#define Rx7 0x40 /* Rx 7 Bits/Character */ 89#define Rx6 0x80 /* Rx 6 Bits/Character */ 90#define Rx8 0xc0 /* Rx 8 Bits/Character */ 91#define RxN_MASK 0xc0 92 93/* Write Register 4 */ 94 95#define PAR_ENAB 0x1 /* Parity Enable */ 96#define PAR_EVEN 0x2 /* Parity Even/Odd* */ 97 98#define SYNC_ENAB 0 /* Sync Modes Enable */ 99#define SB1 0x4 /* 1 stop bit/char */ 100#define SB15 0x8 /* 1.5 stop bits/char */ 101#define SB2 0xc /* 2 stop bits/char */ 102 103#define MONSYNC 0 /* 8 Bit Sync character */ 104#define BISYNC 0x10 /* 16 bit sync character */ 105#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */ 106#define EXTSYNC 0x30 /* External Sync Mode */ 107 108#define X1CLK 0x0 /* x1 clock mode */ 109#define X16CLK 0x40 /* x16 clock mode */ 110#define X32CLK 0x80 /* x32 clock mode */ 111#define X64CLK 0xC0 /* x64 clock mode */ 112#define XCLK_MASK 0xC0 113 114/* Write Register 5 */ 115 116#define TxCRC_ENAB 0x1 /* Tx CRC Enable */ 117#define RTS 0x2 /* RTS */ 118#define SDLC_CRC 0x4 /* SDLC/CRC-16 */ 119#define TxENAB 0x8 /* Tx Enable */ 120#define SND_BRK 0x10 /* Send Break */ 121#define Tx5 0x0 /* Tx 5 bits (or less)/character */ 122#define Tx7 0x20 /* Tx 7 bits/character */ 123#define Tx6 0x40 /* Tx 6 bits/character */ 124#define Tx8 0x60 /* Tx 8 bits/character */ 125#define TxN_MASK 0x60 126#define DTR 0x80 /* DTR */ 127 128/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */ 129 130/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */ 131 132/* Write Register 7' (ESCC Only) */ 133#define AUTO_TxFLAG 1 /* Automatic Tx SDLC Flag */ 134#define AUTO_EOM_RST 2 /* Automatic EOM Reset */ 135#define AUTOnRTS 4 /* Automatic /RTS pin deactivation */ 136#define RxFIFO_LVL 8 /* Receive FIFO interrupt level */ 137#define nDTRnREQ 0x10 /* /DTR/REQ timing */ 138#define TxFIFO_LVL 0x20 /* Transmit FIFO interrupt level */ 139#define EXT_RD_EN 0x40 /* Extended read register enable */ 140 141/* Write Register 8 (transmit buffer) */ 142 143/* Write Register 9 (Master interrupt control) */ 144#define VIS 1 /* Vector Includes Status */ 145#define NV 2 /* No Vector */ 146#define DLC 4 /* Disable Lower Chain */ 147#define MIE 8 /* Master Interrupt Enable */ 148#define STATHI 0x10 /* Status high */ 149#define SWIACK 0x20 /* Software Interrupt Ack (not on NMOS) */ 150#define NORESET 0 /* No reset on write to R9 */ 151#define CHRB 0x40 /* Reset channel B */ 152#define CHRA 0x80 /* Reset channel A */ 153#define FHWRES 0xc0 /* Force hardware reset */ 154 155/* Write Register 10 (misc control bits) */ 156#define BIT6 1 /* 6 bit/8bit sync */ 157#define LOOPMODE 2 /* SDLC Loop mode */ 158#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */ 159#define MARKIDLE 8 /* Mark/flag on idle */ 160#define GAOP 0x10 /* Go active on poll */ 161#define NRZ 0 /* NRZ mode */ 162#define NRZI 0x20 /* NRZI mode */ 163#define FM1 0x40 /* FM1 (transition = 1) */ 164#define FM0 0x60 /* FM0 (transition = 0) */ 165#define CRCPS 0x80 /* CRC Preset I/O */ 166 167/* Write Register 11 (Clock Mode control) */ 168#define TRxCXT 0 /* TRxC = Xtal output */ 169#define TRxCTC 1 /* TRxC = Transmit clock */ 170#define TRxCBR 2 /* TRxC = BR Generator Output */ 171#define TRxCDP 3 /* TRxC = DPLL output */ 172#define TRxCOI 4 /* TRxC O/I */ 173#define TCRTxCP 0 /* Transmit clock = RTxC pin */ 174#define TCTRxCP 8 /* Transmit clock = TRxC pin */ 175#define TCBR 0x10 /* Transmit clock = BR Generator output */ 176#define TCDPLL 0x18 /* Transmit clock = DPLL output */ 177#define RCRTxCP 0 /* Receive clock = RTxC pin */ 178#define RCTRxCP 0x20 /* Receive clock = TRxC pin */ 179#define RCBR 0x40 /* Receive clock = BR Generator output */ 180#define RCDPLL 0x60 /* Receive clock = DPLL output */ 181#define RTxCX 0x80 /* RTxC Xtal/No Xtal */ 182 183/* Write Register 12 (lower byte of baud rate generator time constant) */ 184 185/* Write Register 13 (upper byte of baud rate generator time constant) */ 186 187/* Write Register 14 (Misc control bits) */ 188#define BRENAB 1 /* Baud rate generator enable */ 189#define BRSRC 2 /* Baud rate generator source */ 190#define DTRREQ 4 /* DTR/Request function */ 191#define AUTOECHO 8 /* Auto Echo */ 192#define LOOPBAK 0x10 /* Local loopback */ 193#define SEARCH 0x20 /* Enter search mode */ 194#define RMC 0x40 /* Reset missing clock */ 195#define DISDPLL 0x60 /* Disable DPLL */ 196#define SSBR 0x80 /* Set DPLL source = BR generator */ 197#define SSRTxC 0xa0 /* Set DPLL source = RTxC */ 198#define SFMM 0xc0 /* Set FM mode */ 199#define SNRZI 0xe0 /* Set NRZI mode */ 200 201/* Write Register 15 (external/status interrupt control) */ 202#define WR7pEN 1 /* WR7' Enable (ESCC only) */ 203#define ZCIE 2 /* Zero count IE */ 204#define FIFOEN 4 /* FIFO Enable (ESCC only) */ 205#define DCDIE 8 /* DCD IE */ 206#define SYNCIE 0x10 /* Sync/hunt IE */ 207#define CTSIE 0x20 /* CTS IE */ 208#define TxUIE 0x40 /* Tx Underrun/EOM IE */ 209#define BRKIE 0x80 /* Break/Abort IE */ 210 211 212/* Read Register 0 */ 213#define Rx_CH_AV 0x1 /* Rx Character Available */ 214#define ZCOUNT 0x2 /* Zero count */ 215#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */ 216#define DCD 0x8 /* DCD */ 217#define SYNC 0x10 /* Sync/hunt */ 218#define CTS 0x20 /* CTS */ 219#define TxEOM 0x40 /* Tx underrun */ 220#define BRK_ABRT 0x80 /* Break/Abort */ 221 222/* Read Register 1 */ 223#define ALL_SNT 0x1 /* All sent */ 224/* Residue Data for 8 Rx bits/char programmed */ 225#define RES3 0x8 /* 0/3 */ 226#define RES4 0x4 /* 0/4 */ 227#define RES5 0xc /* 0/5 */ 228#define RES6 0x2 /* 0/6 */ 229#define RES7 0xa /* 0/7 */ 230#define RES8 0x6 /* 0/8 */ 231#define RES18 0xe /* 1/8 */ 232#define RES28 0x0 /* 2/8 */ 233/* Special Rx Condition Interrupts */ 234#define PAR_ERR 0x10 /* Parity error */ 235#define Rx_OVR 0x20 /* Rx Overrun Error */ 236#define CRC_ERR 0x40 /* CRC/Framing Error */ 237#define END_FR 0x80 /* End of Frame (SDLC) */ 238 239/* Read Register 2 (channel b only) - Interrupt vector */ 240#define CHB_Tx_EMPTY 0x00 241#define CHB_EXT_STAT 0x02 242#define CHB_Rx_AVAIL 0x04 243#define CHB_SPECIAL 0x06 244#define CHA_Tx_EMPTY 0x08 245#define CHA_EXT_STAT 0x0a 246#define CHA_Rx_AVAIL 0x0c 247#define CHA_SPECIAL 0x0e 248#define STATUS_MASK 0x0e 249 250/* Read Register 3 (interrupt pending register) ch a only */ 251#define CHBEXT 0x1 /* Channel B Ext/Stat IP */ 252#define CHBTxIP 0x2 /* Channel B Tx IP */ 253#define CHBRxIP 0x4 /* Channel B Rx IP */ 254#define CHAEXT 0x8 /* Channel A Ext/Stat IP */ 255#define CHATxIP 0x10 /* Channel A Tx IP */ 256#define CHARxIP 0x20 /* Channel A Rx IP */ 257 258/* Read Register 6 (LSB frame byte count [Not on NMOS]) */ 259 260/* Read Register 7 (MSB frame byte count and FIFO status [Not on NMOS]) */ 261 262/* Read Register 8 (receive data register) */ 263 264/* Read Register 10 (misc status bits) */ 265#define ONLOOP 2 /* On loop */ 266#define LOOPSEND 0x10 /* Loop sending */ 267#define CLK2MIS 0x40 /* Two clocks missing */ 268#define CLK1MIS 0x80 /* One clock missing */ 269 270/* Read Register 12 (lower byte of baud rate generator constant) */ 271 272/* Read Register 13 (upper byte of baud rate generator constant) */ 273 274/* Read Register 15 (value of WR 15) */ 275 276/* Misc macros */ 277#define ZS_CLEARERR(channel) do { sbus_writeb(ERR_RES, &channel->control); \ 278 udelay(5); } while(0) 279 280#define ZS_CLEARSTAT(channel) do { sbus_writeb(RES_EXT_INT, &channel->control); \ 281 udelay(5); } while(0) 282 283#define ZS_CLEARFIFO(channel) do { sbus_readb(&channel->data); \ 284 udelay(2); \ 285 sbus_readb(&channel->data); \ 286 udelay(2); \ 287 sbus_readb(&channel->data); \ 288 udelay(2); } while(0) 289 290#endif /* _SUNZILOG_H */