mv_udc.h (9500B)
1// SPDX-License-Identifier: GPL-2.0+ 2/* 3 * Copyright (C) 2011 Marvell International Ltd. All rights reserved. 4 */ 5 6#ifndef __MV_UDC_H 7#define __MV_UDC_H 8 9#define VUSBHS_MAX_PORTS 8 10 11#define DQH_ALIGNMENT 2048 12#define DTD_ALIGNMENT 64 13#define DMA_BOUNDARY 4096 14 15#define EP_DIR_IN 1 16#define EP_DIR_OUT 0 17 18#define DMA_ADDR_INVALID (~(dma_addr_t)0) 19 20#define EP0_MAX_PKT_SIZE 64 21/* ep0 transfer state */ 22#define WAIT_FOR_SETUP 0 23#define DATA_STATE_XMIT 1 24#define DATA_STATE_NEED_ZLP 2 25#define WAIT_FOR_OUT_STATUS 3 26#define DATA_STATE_RECV 4 27 28#define CAPLENGTH_MASK (0xff) 29#define DCCPARAMS_DEN_MASK (0x1f) 30 31#define HCSPARAMS_PPC (0x10) 32 33/* Frame Index Register Bit Masks */ 34#define USB_FRINDEX_MASKS 0x3fff 35 36/* Command Register Bit Masks */ 37#define USBCMD_RUN_STOP (0x00000001) 38#define USBCMD_CTRL_RESET (0x00000002) 39#define USBCMD_SETUP_TRIPWIRE_SET (0x00002000) 40#define USBCMD_SETUP_TRIPWIRE_CLEAR (~USBCMD_SETUP_TRIPWIRE_SET) 41 42#define USBCMD_ATDTW_TRIPWIRE_SET (0x00004000) 43#define USBCMD_ATDTW_TRIPWIRE_CLEAR (~USBCMD_ATDTW_TRIPWIRE_SET) 44 45/* bit 15,3,2 are for frame list size */ 46#define USBCMD_FRAME_SIZE_1024 (0x00000000) /* 000 */ 47#define USBCMD_FRAME_SIZE_512 (0x00000004) /* 001 */ 48#define USBCMD_FRAME_SIZE_256 (0x00000008) /* 010 */ 49#define USBCMD_FRAME_SIZE_128 (0x0000000C) /* 011 */ 50#define USBCMD_FRAME_SIZE_64 (0x00008000) /* 100 */ 51#define USBCMD_FRAME_SIZE_32 (0x00008004) /* 101 */ 52#define USBCMD_FRAME_SIZE_16 (0x00008008) /* 110 */ 53#define USBCMD_FRAME_SIZE_8 (0x0000800C) /* 111 */ 54 55#define EPCTRL_TX_ALL_MASK (0xFFFF0000) 56#define EPCTRL_RX_ALL_MASK (0x0000FFFF) 57 58#define EPCTRL_TX_DATA_TOGGLE_RST (0x00400000) 59#define EPCTRL_TX_EP_STALL (0x00010000) 60#define EPCTRL_RX_EP_STALL (0x00000001) 61#define EPCTRL_RX_DATA_TOGGLE_RST (0x00000040) 62#define EPCTRL_RX_ENABLE (0x00000080) 63#define EPCTRL_TX_ENABLE (0x00800000) 64#define EPCTRL_CONTROL (0x00000000) 65#define EPCTRL_ISOCHRONOUS (0x00040000) 66#define EPCTRL_BULK (0x00080000) 67#define EPCTRL_INT (0x000C0000) 68#define EPCTRL_TX_TYPE (0x000C0000) 69#define EPCTRL_RX_TYPE (0x0000000C) 70#define EPCTRL_DATA_TOGGLE_INHIBIT (0x00000020) 71#define EPCTRL_TX_EP_TYPE_SHIFT (18) 72#define EPCTRL_RX_EP_TYPE_SHIFT (2) 73 74#define EPCOMPLETE_MAX_ENDPOINTS (16) 75 76/* endpoint list address bit masks */ 77#define USB_EP_LIST_ADDRESS_MASK 0xfffff800 78 79#define PORTSCX_W1C_BITS 0x2a 80#define PORTSCX_PORT_RESET 0x00000100 81#define PORTSCX_PORT_POWER 0x00001000 82#define PORTSCX_FORCE_FULL_SPEED_CONNECT 0x01000000 83#define PORTSCX_PAR_XCVR_SELECT 0xC0000000 84#define PORTSCX_PORT_FORCE_RESUME 0x00000040 85#define PORTSCX_PORT_SUSPEND 0x00000080 86#define PORTSCX_PORT_SPEED_FULL 0x00000000 87#define PORTSCX_PORT_SPEED_LOW 0x04000000 88#define PORTSCX_PORT_SPEED_HIGH 0x08000000 89#define PORTSCX_PORT_SPEED_MASK 0x0C000000 90 91/* USB MODE Register Bit Masks */ 92#define USBMODE_CTRL_MODE_IDLE 0x00000000 93#define USBMODE_CTRL_MODE_DEVICE 0x00000002 94#define USBMODE_CTRL_MODE_HOST 0x00000003 95#define USBMODE_CTRL_MODE_RSV 0x00000001 96#define USBMODE_SETUP_LOCK_OFF 0x00000008 97#define USBMODE_STREAM_DISABLE 0x00000010 98 99/* USB STS Register Bit Masks */ 100#define USBSTS_INT 0x00000001 101#define USBSTS_ERR 0x00000002 102#define USBSTS_PORT_CHANGE 0x00000004 103#define USBSTS_FRM_LST_ROLL 0x00000008 104#define USBSTS_SYS_ERR 0x00000010 105#define USBSTS_IAA 0x00000020 106#define USBSTS_RESET 0x00000040 107#define USBSTS_SOF 0x00000080 108#define USBSTS_SUSPEND 0x00000100 109#define USBSTS_HC_HALTED 0x00001000 110#define USBSTS_RCL 0x00002000 111#define USBSTS_PERIODIC_SCHEDULE 0x00004000 112#define USBSTS_ASYNC_SCHEDULE 0x00008000 113 114 115/* Interrupt Enable Register Bit Masks */ 116#define USBINTR_INT_EN (0x00000001) 117#define USBINTR_ERR_INT_EN (0x00000002) 118#define USBINTR_PORT_CHANGE_DETECT_EN (0x00000004) 119 120#define USBINTR_ASYNC_ADV_AAE (0x00000020) 121#define USBINTR_ASYNC_ADV_AAE_ENABLE (0x00000020) 122#define USBINTR_ASYNC_ADV_AAE_DISABLE (0xFFFFFFDF) 123 124#define USBINTR_RESET_EN (0x00000040) 125#define USBINTR_SOF_UFRAME_EN (0x00000080) 126#define USBINTR_DEVICE_SUSPEND (0x00000100) 127 128#define USB_DEVICE_ADDRESS_MASK (0xfe000000) 129#define USB_DEVICE_ADDRESS_BIT_SHIFT (25) 130 131struct mv_cap_regs { 132 u32 caplength_hciversion; 133 u32 hcsparams; /* HC structural parameters */ 134 u32 hccparams; /* HC Capability Parameters*/ 135 u32 reserved[5]; 136 u32 dciversion; /* DC version number and reserved 16 bits */ 137 u32 dccparams; /* DC Capability Parameters */ 138}; 139 140struct mv_op_regs { 141 u32 usbcmd; /* Command register */ 142 u32 usbsts; /* Status register */ 143 u32 usbintr; /* Interrupt enable */ 144 u32 frindex; /* Frame index */ 145 u32 reserved1[1]; 146 u32 deviceaddr; /* Device Address */ 147 u32 eplistaddr; /* Endpoint List Address */ 148 u32 ttctrl; /* HOST TT status and control */ 149 u32 burstsize; /* Programmable Burst Size */ 150 u32 txfilltuning; /* Host Transmit Pre-Buffer Packet Tuning */ 151 u32 reserved[4]; 152 u32 epnak; /* Endpoint NAK */ 153 u32 epnaken; /* Endpoint NAK Enable */ 154 u32 configflag; /* Configured Flag register */ 155 u32 portsc[VUSBHS_MAX_PORTS]; /* Port Status/Control x, x = 1..8 */ 156 u32 otgsc; 157 u32 usbmode; /* USB Host/Device mode */ 158 u32 epsetupstat; /* Endpoint Setup Status */ 159 u32 epprime; /* Endpoint Initialize */ 160 u32 epflush; /* Endpoint De-initialize */ 161 u32 epstatus; /* Endpoint Status */ 162 u32 epcomplete; /* Endpoint Interrupt On Complete */ 163 u32 epctrlx[16]; /* Endpoint Control, where x = 0.. 15 */ 164 u32 mcr; /* Mux Control */ 165 u32 isr; /* Interrupt Status */ 166 u32 ier; /* Interrupt Enable */ 167}; 168 169struct mv_udc { 170 struct usb_gadget gadget; 171 struct usb_gadget_driver *driver; 172 spinlock_t lock; 173 struct completion *done; 174 struct platform_device *dev; 175 int irq; 176 177 struct mv_cap_regs __iomem *cap_regs; 178 struct mv_op_regs __iomem *op_regs; 179 void __iomem *phy_regs; 180 unsigned int max_eps; 181 struct mv_dqh *ep_dqh; 182 size_t ep_dqh_size; 183 dma_addr_t ep_dqh_dma; 184 185 struct dma_pool *dtd_pool; 186 struct mv_ep *eps; 187 188 struct mv_dtd *dtd_head; 189 struct mv_dtd *dtd_tail; 190 unsigned int dtd_entries; 191 192 struct mv_req *status_req; 193 struct usb_ctrlrequest local_setup_buff; 194 195 unsigned int resume_state; /* USB state to resume */ 196 unsigned int usb_state; /* USB current state */ 197 unsigned int ep0_state; /* Endpoint zero state */ 198 unsigned int ep0_dir; 199 200 unsigned int dev_addr; 201 unsigned int test_mode; 202 203 int errors; 204 unsigned softconnect:1, 205 vbus_active:1, 206 remote_wakeup:1, 207 softconnected:1, 208 force_fs:1, 209 clock_gating:1, 210 active:1, 211 stopped:1; /* stop bit is setted */ 212 213 struct work_struct vbus_work; 214 struct workqueue_struct *qwork; 215 216 struct usb_phy *transceiver; 217 218 struct mv_usb_platform_data *pdata; 219 220 /* some SOC has mutiple clock sources for USB*/ 221 struct clk *clk; 222}; 223 224/* endpoint data structure */ 225struct mv_ep { 226 struct usb_ep ep; 227 struct mv_udc *udc; 228 struct list_head queue; 229 struct mv_dqh *dqh; 230 u32 direction; 231 char name[14]; 232 unsigned stopped:1, 233 wedge:1, 234 ep_type:2, 235 ep_num:8; 236}; 237 238/* request data structure */ 239struct mv_req { 240 struct usb_request req; 241 struct mv_dtd *dtd, *head, *tail; 242 struct mv_ep *ep; 243 struct list_head queue; 244 unsigned int test_mode; 245 unsigned dtd_count; 246 unsigned mapped:1; 247}; 248 249#define EP_QUEUE_HEAD_MULT_POS 30 250#define EP_QUEUE_HEAD_ZLT_SEL 0x20000000 251#define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16 252#define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff) 253#define EP_QUEUE_HEAD_IOS 0x00008000 254#define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001 255#define EP_QUEUE_HEAD_IOC 0x00008000 256#define EP_QUEUE_HEAD_MULTO 0x00000C00 257#define EP_QUEUE_HEAD_STATUS_HALT 0x00000040 258#define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080 259#define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF 260#define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0 261#define EP_QUEUE_FRINDEX_MASK 0x000007FF 262#define EP_MAX_LENGTH_TRANSFER 0x4000 263 264struct mv_dqh { 265 /* Bits 16..26 Bit 15 is Interrupt On Setup */ 266 u32 max_packet_length; 267 u32 curr_dtd_ptr; /* Current dTD Pointer */ 268 u32 next_dtd_ptr; /* Next dTD Pointer */ 269 /* Total bytes (16..30), IOC (15), INT (8), STS (0-7) */ 270 u32 size_ioc_int_sts; 271 u32 buff_ptr0; /* Buffer pointer Page 0 (12-31) */ 272 u32 buff_ptr1; /* Buffer pointer Page 1 (12-31) */ 273 u32 buff_ptr2; /* Buffer pointer Page 2 (12-31) */ 274 u32 buff_ptr3; /* Buffer pointer Page 3 (12-31) */ 275 u32 buff_ptr4; /* Buffer pointer Page 4 (12-31) */ 276 u32 reserved1; 277 /* 8 bytes of setup data that follows the Setup PID */ 278 u8 setup_buffer[8]; 279 u32 reserved2[4]; 280}; 281 282 283#define DTD_NEXT_TERMINATE (0x00000001) 284#define DTD_IOC (0x00008000) 285#define DTD_STATUS_ACTIVE (0x00000080) 286#define DTD_STATUS_HALTED (0x00000040) 287#define DTD_STATUS_DATA_BUFF_ERR (0x00000020) 288#define DTD_STATUS_TRANSACTION_ERR (0x00000008) 289#define DTD_RESERVED_FIELDS (0x00007F00) 290#define DTD_ERROR_MASK (0x68) 291#define DTD_ADDR_MASK (0xFFFFFFE0) 292#define DTD_PACKET_SIZE 0x7FFF0000 293#define DTD_LENGTH_BIT_POS (16) 294 295struct mv_dtd { 296 u32 dtd_next; 297 u32 size_ioc_sts; 298 u32 buff_ptr0; /* Buffer pointer Page 0 */ 299 u32 buff_ptr1; /* Buffer pointer Page 1 */ 300 u32 buff_ptr2; /* Buffer pointer Page 2 */ 301 u32 buff_ptr3; /* Buffer pointer Page 3 */ 302 u32 buff_ptr4; /* Buffer pointer Page 4 */ 303 u32 scratch_ptr; 304 /* 32 bytes */ 305 dma_addr_t td_dma; /* dma address for this td */ 306 struct mv_dtd *next_dtd_virt; 307}; 308 309#endif