omap.h (3163B)
1/* SPDX-License-Identifier: GPL-2.0 */ 2/* 3 * This header provides constants for OMAP pinctrl bindings. 4 * 5 * Copyright (C) 2009 Nokia 6 * Copyright (C) 2009-2010 Texas Instruments 7 */ 8 9#ifndef _DT_BINDINGS_PINCTRL_OMAP_H 10#define _DT_BINDINGS_PINCTRL_OMAP_H 11 12/* 34xx mux mode options for each pin. See TRM for options */ 13#define MUX_MODE0 0 14#define MUX_MODE1 1 15#define MUX_MODE2 2 16#define MUX_MODE3 3 17#define MUX_MODE4 4 18#define MUX_MODE5 5 19#define MUX_MODE6 6 20#define MUX_MODE7 7 21 22/* 24xx/34xx mux bit defines */ 23#define PULL_ENA (1 << 3) 24#define PULL_UP (1 << 4) 25#define ALTELECTRICALSEL (1 << 5) 26 27/* omap3/4/5 specific mux bit defines */ 28#define INPUT_EN (1 << 8) 29#define OFF_EN (1 << 9) 30#define OFFOUT_EN (1 << 10) 31#define OFFOUT_VAL (1 << 11) 32#define OFF_PULL_EN (1 << 12) 33#define OFF_PULL_UP (1 << 13) 34#define WAKEUP_EN (1 << 14) 35#define WAKEUP_EVENT (1 << 15) 36 37/* Active pin states */ 38#define PIN_OUTPUT 0 39#define PIN_OUTPUT_PULLUP (PIN_OUTPUT | PULL_ENA | PULL_UP) 40#define PIN_OUTPUT_PULLDOWN (PIN_OUTPUT | PULL_ENA) 41#define PIN_INPUT INPUT_EN 42#define PIN_INPUT_PULLUP (PULL_ENA | INPUT_EN | PULL_UP) 43#define PIN_INPUT_PULLDOWN (PULL_ENA | INPUT_EN) 44 45/* Off mode states */ 46#define PIN_OFF_NONE 0 47#define PIN_OFF_OUTPUT_HIGH (OFF_EN | OFFOUT_EN | OFFOUT_VAL) 48#define PIN_OFF_OUTPUT_LOW (OFF_EN | OFFOUT_EN) 49#define PIN_OFF_INPUT_PULLUP (OFF_EN | OFFOUT_EN | OFF_PULL_EN | OFF_PULL_UP) 50#define PIN_OFF_INPUT_PULLDOWN (OFF_EN | OFFOUT_EN | OFF_PULL_EN) 51#define PIN_OFF_WAKEUPENABLE WAKEUP_EN 52 53/* 54 * Macros to allow using the absolute physical address instead of the 55 * padconf registers instead of the offset from padconf base. 56 */ 57#define OMAP_IOPAD_OFFSET(pa, offset) (((pa) & 0xffff) - (offset)) 58 59#define OMAP2420_CORE_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0030) (val) 60#define OMAP2430_CORE_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x2030) (val) 61#define OMAP3_CORE1_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x2030) (val) 62#define OMAP3430_CORE2_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x25d8) (val) 63#define OMAP3630_CORE2_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x25a0) (val) 64#define OMAP3_WKUP_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x2a00) (val) 65#define DM814X_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) 66#define DM816X_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) 67#define AM33XX_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val) (0) 68#define AM33XX_PADCONF(pa, conf, mux) OMAP_IOPAD_OFFSET((pa), 0x0800) (conf) (mux) 69 70/* 71 * Macros to allow using the offset from the padconf physical address 72 * instead of the offset from padconf base. 73 */ 74#define OMAP_PADCONF_OFFSET(offset, base_offset) ((offset) - (base_offset)) 75 76#define OMAP4_IOPAD(offset, val) OMAP_PADCONF_OFFSET((offset), 0x0040) (val) 77#define OMAP5_IOPAD(offset, val) OMAP_PADCONF_OFFSET((offset), 0x0040) (val) 78 79/* 80 * Define some commonly used pins configured by the boards. 81 * Note that some boards use alternative pins, so check 82 * the schematics before using these. 83 */ 84#define OMAP3_UART1_RX 0x152 85#define OMAP3_UART2_RX 0x14a 86#define OMAP3_UART3_RX 0x16e 87#define OMAP4_UART2_RX 0xdc 88#define OMAP4_UART3_RX 0x104 89#define OMAP4_UART4_RX 0x11c 90 91#endif 92