lis3lv02d.h (5125B)
1/* SPDX-License-Identifier: GPL-2.0 */ 2#ifndef __LIS3LV02D_H_ 3#define __LIS3LV02D_H_ 4 5/** 6 * struct lis3lv02d_platform_data - lis3 chip family platform data 7 * @click_flags: Click detection unit configuration 8 * @click_thresh_x: Click detection unit x axis threshold 9 * @click_thresh_y: Click detection unit y axis threshold 10 * @click_thresh_z: Click detection unit z axis threshold 11 * @click_time_limit: Click detection unit time parameter 12 * @click_latency: Click detection unit latency parameter 13 * @click_window: Click detection unit window parameter 14 * @irq_cfg: On chip irq source and type configuration (click / 15 * data available / wake up, open drain, polarity) 16 * @irq_flags1: Additional irq triggering flags for irq channel 0 17 * @irq_flags2: Additional irq triggering flags for irq channel 1 18 * @duration1: Wake up unit 1 duration parameter 19 * @duration2: Wake up unit 2 duration parameter 20 * @wakeup_flags: Wake up unit 1 flags 21 * @wakeup_thresh: Wake up unit 1 threshold value 22 * @wakeup_flags2: Wake up unit 2 flags 23 * @wakeup_thresh2: Wake up unit 2 threshold value 24 * @hipass_ctrl: High pass filter control (enable / disable, cut off 25 * frequency) 26 * @axis_x: Sensor orientation remapping for x-axis 27 * @axis_y: Sensor orientation remapping for y-axis 28 * @axis_z: Sensor orientation remapping for z-axis 29 * @driver_features: Enable bits for different features. Disabled by default 30 * @default_rate: Default sampling rate. 0 means reset default 31 * @setup_resources: Interrupt line setup call back function 32 * @release_resources: Interrupt line release call back function 33 * @st_min_limits[3]: Selftest acceptance minimum values 34 * @st_max_limits[3]: Selftest acceptance maximum values 35 * @irq2: Irq line 2 number 36 * 37 * Platform data is used to setup the sensor chip. Meaning of the different 38 * chip features can be found from the data sheet. It is publicly available 39 * at www.st.com web pages. Currently the platform data is used 40 * only for the 8 bit device. The 8 bit device has two wake up / free fall 41 * detection units and click detection unit. There are plenty of ways to 42 * configure the chip which makes is quite hard to explain deeper meaning of 43 * the fields here. Behaviour of the detection blocks varies heavily depending 44 * on the configuration. For example, interrupt detection block can use high 45 * pass filtered data which makes it react to the changes in the acceleration. 46 * Irq_flags can be used to enable interrupt detection on the both edges. 47 * With proper chip configuration this produces interrupt when some trigger 48 * starts and when it goes away. 49 */ 50 51struct lis3lv02d_platform_data { 52 /* please note: the 'click' feature is only supported for 53 * LIS[32]02DL variants of the chip and will be ignored for 54 * others */ 55#define LIS3_CLICK_SINGLE_X (1 << 0) 56#define LIS3_CLICK_DOUBLE_X (1 << 1) 57#define LIS3_CLICK_SINGLE_Y (1 << 2) 58#define LIS3_CLICK_DOUBLE_Y (1 << 3) 59#define LIS3_CLICK_SINGLE_Z (1 << 4) 60#define LIS3_CLICK_DOUBLE_Z (1 << 5) 61 unsigned char click_flags; 62 unsigned char click_thresh_x; 63 unsigned char click_thresh_y; 64 unsigned char click_thresh_z; 65 unsigned char click_time_limit; 66 unsigned char click_latency; 67 unsigned char click_window; 68 69#define LIS3_IRQ1_DISABLE (0 << 0) 70#define LIS3_IRQ1_FF_WU_1 (1 << 0) 71#define LIS3_IRQ1_FF_WU_2 (2 << 0) 72#define LIS3_IRQ1_FF_WU_12 (3 << 0) 73#define LIS3_IRQ1_DATA_READY (4 << 0) 74#define LIS3_IRQ1_CLICK (7 << 0) 75#define LIS3_IRQ1_MASK (7 << 0) 76#define LIS3_IRQ2_DISABLE (0 << 3) 77#define LIS3_IRQ2_FF_WU_1 (1 << 3) 78#define LIS3_IRQ2_FF_WU_2 (2 << 3) 79#define LIS3_IRQ2_FF_WU_12 (3 << 3) 80#define LIS3_IRQ2_DATA_READY (4 << 3) 81#define LIS3_IRQ2_CLICK (7 << 3) 82#define LIS3_IRQ2_MASK (7 << 3) 83#define LIS3_IRQ_OPEN_DRAIN (1 << 6) 84#define LIS3_IRQ_ACTIVE_LOW (1 << 7) 85 unsigned char irq_cfg; 86 unsigned char irq_flags1; /* Additional irq edge / level flags */ 87 unsigned char irq_flags2; /* Additional irq edge / level flags */ 88 unsigned char duration1; 89 unsigned char duration2; 90#define LIS3_WAKEUP_X_LO (1 << 0) 91#define LIS3_WAKEUP_X_HI (1 << 1) 92#define LIS3_WAKEUP_Y_LO (1 << 2) 93#define LIS3_WAKEUP_Y_HI (1 << 3) 94#define LIS3_WAKEUP_Z_LO (1 << 4) 95#define LIS3_WAKEUP_Z_HI (1 << 5) 96 unsigned char wakeup_flags; 97 unsigned char wakeup_thresh; 98 unsigned char wakeup_flags2; 99 unsigned char wakeup_thresh2; 100#define LIS3_HIPASS_CUTFF_8HZ 0 101#define LIS3_HIPASS_CUTFF_4HZ 1 102#define LIS3_HIPASS_CUTFF_2HZ 2 103#define LIS3_HIPASS_CUTFF_1HZ 3 104#define LIS3_HIPASS1_DISABLE (1 << 2) 105#define LIS3_HIPASS2_DISABLE (1 << 3) 106 unsigned char hipass_ctrl; 107#define LIS3_NO_MAP 0 108#define LIS3_DEV_X 1 109#define LIS3_DEV_Y 2 110#define LIS3_DEV_Z 3 111#define LIS3_INV_DEV_X -1 112#define LIS3_INV_DEV_Y -2 113#define LIS3_INV_DEV_Z -3 114 s8 axis_x; 115 s8 axis_y; 116 s8 axis_z; 117#define LIS3_USE_BLOCK_READ 0x02 118 u16 driver_features; 119 int default_rate; 120 int (*setup_resources)(void); 121 int (*release_resources)(void); 122 /* Limits for selftest are specified in chip data sheet */ 123 s16 st_min_limits[3]; /* min pass limit x, y, z */ 124 s16 st_max_limits[3]; /* max pass limit x, y, z */ 125 int irq2; 126}; 127 128#endif /* __LIS3LV02D_H_ */