max8997.h (5513B)
1/* SPDX-License-Identifier: GPL-2.0+ */ 2/* 3 * max8997.h - Driver for the Maxim 8997/8966 4 * 5 * Copyright (C) 2009-2010 Samsung Electrnoics 6 * MyungJoo Ham <myungjoo.ham@samsung.com> 7 * 8 * This driver is based on max8998.h 9 * 10 * MAX8997 has PMIC, MUIC, HAPTIC, RTC, FLASH, and Fuel Gauge devices. 11 * Except Fuel Gauge, every device shares the same I2C bus and included in 12 * this mfd driver. Although the fuel gauge is included in the chip, it is 13 * excluded from the driver because a) it has a different I2C bus from 14 * others and b) it can be enabled simply by using MAX17042 driver. 15 */ 16 17#ifndef __LINUX_MFD_MAX8997_H 18#define __LINUX_MFD_MAX8997_H 19 20#include <linux/regulator/consumer.h> 21 22/* MAX8997/8966 regulator IDs */ 23enum max8997_regulators { 24 MAX8997_LDO1 = 0, 25 MAX8997_LDO2, 26 MAX8997_LDO3, 27 MAX8997_LDO4, 28 MAX8997_LDO5, 29 MAX8997_LDO6, 30 MAX8997_LDO7, 31 MAX8997_LDO8, 32 MAX8997_LDO9, 33 MAX8997_LDO10, 34 MAX8997_LDO11, 35 MAX8997_LDO12, 36 MAX8997_LDO13, 37 MAX8997_LDO14, 38 MAX8997_LDO15, 39 MAX8997_LDO16, 40 MAX8997_LDO17, 41 MAX8997_LDO18, 42 MAX8997_LDO21, 43 MAX8997_BUCK1, 44 MAX8997_BUCK2, 45 MAX8997_BUCK3, 46 MAX8997_BUCK4, 47 MAX8997_BUCK5, 48 MAX8997_BUCK6, 49 MAX8997_BUCK7, 50 MAX8997_EN32KHZ_AP, 51 MAX8997_EN32KHZ_CP, 52 MAX8997_ENVICHG, 53 MAX8997_ESAFEOUT1, 54 MAX8997_ESAFEOUT2, 55 MAX8997_CHARGER_CV, /* control MBCCV of MBCCTRL3 */ 56 MAX8997_CHARGER, /* charger current, MBCCTRL4 */ 57 MAX8997_CHARGER_TOPOFF, /* MBCCTRL5 */ 58 59 MAX8997_REG_MAX, 60}; 61 62struct max8997_regulator_data { 63 int id; 64 struct regulator_init_data *initdata; 65 struct device_node *reg_node; 66}; 67 68struct max8997_muic_reg_data { 69 u8 addr; 70 u8 data; 71}; 72 73/** 74 * struct max8997_muic_platform_data 75 * @init_data: array of max8997_muic_reg_data 76 * used for initializing registers of MAX8997 MUIC device 77 * @num_init_data: array size of init_data 78 */ 79struct max8997_muic_platform_data { 80 struct max8997_muic_reg_data *init_data; 81 int num_init_data; 82 83 /* Check cable state after certain delay */ 84 int detcable_delay_ms; 85 86 /* 87 * Default usb/uart path whether UART/USB or AUX_UART/AUX_USB 88 * h/w path of COMP2/COMN1 on CONTROL1 register. 89 */ 90 int path_usb; 91 int path_uart; 92}; 93 94enum max8997_haptic_motor_type { 95 MAX8997_HAPTIC_ERM, 96 MAX8997_HAPTIC_LRA, 97}; 98 99enum max8997_haptic_pulse_mode { 100 MAX8997_EXTERNAL_MODE, 101 MAX8997_INTERNAL_MODE, 102}; 103 104enum max8997_haptic_pwm_divisor { 105 MAX8997_PWM_DIVISOR_32, 106 MAX8997_PWM_DIVISOR_64, 107 MAX8997_PWM_DIVISOR_128, 108 MAX8997_PWM_DIVISOR_256, 109}; 110 111/** 112 * max8997_haptic_platform_data 113 * @pwm_channel_id: channel number of PWM device 114 * valid for MAX8997_EXTERNAL_MODE 115 * @pwm_period: period in nano second for PWM device 116 * valid for MAX8997_EXTERNAL_MODE 117 * @type: motor type 118 * @mode: pulse mode 119 * MAX8997_EXTERNAL_MODE: external PWM device is used to control motor 120 * MAX8997_INTERNAL_MODE: internal pulse generator is used to control motor 121 * @pwm_divisor: divisor for external PWM device 122 * @internal_mode_pattern: internal mode pattern for internal mode 123 * [0 - 3]: valid pattern number 124 * @pattern_cycle: the number of cycles of the waveform 125 * for the internal mode pattern 126 * [0 - 15]: available cycles 127 * @pattern_signal_period: period of the waveform for the internal mode pattern 128 * [0 - 255]: available period 129 */ 130struct max8997_haptic_platform_data { 131 unsigned int pwm_channel_id; 132 unsigned int pwm_period; 133 134 enum max8997_haptic_motor_type type; 135 enum max8997_haptic_pulse_mode mode; 136 enum max8997_haptic_pwm_divisor pwm_divisor; 137 138 unsigned int internal_mode_pattern; 139 unsigned int pattern_cycle; 140 unsigned int pattern_signal_period; 141}; 142 143enum max8997_led_mode { 144 MAX8997_NONE, 145 MAX8997_FLASH_MODE, 146 MAX8997_MOVIE_MODE, 147 MAX8997_FLASH_PIN_CONTROL_MODE, 148 MAX8997_MOVIE_PIN_CONTROL_MODE, 149}; 150 151/** 152 * struct max8997_led_platform_data 153 * The number of LED devices for MAX8997 is two 154 * @mode: LED mode for each LED device 155 * @brightness: initial brightness for each LED device 156 * range: 157 * [0 - 31]: MAX8997_FLASH_MODE and MAX8997_FLASH_PIN_CONTROL_MODE 158 * [0 - 15]: MAX8997_MOVIE_MODE and MAX8997_MOVIE_PIN_CONTROL_MODE 159 */ 160struct max8997_led_platform_data { 161 enum max8997_led_mode mode[2]; 162 u8 brightness[2]; 163}; 164 165struct max8997_platform_data { 166 /* IRQ */ 167 int ono; 168 169 /* ---- PMIC ---- */ 170 struct max8997_regulator_data *regulators; 171 int num_regulators; 172 173 /* 174 * SET1~3 DVS GPIOs control Buck1, 2, and 5 simultaneously. Therefore, 175 * With buckx_gpiodvs enabled, the buckx cannot be controlled 176 * independently. To control buckx (of 1, 2, and 5) independently, 177 * disable buckx_gpiodvs and control with BUCKxDVS1 register. 178 * 179 * When buckx_gpiodvs and bucky_gpiodvs are both enabled, set_voltage 180 * on buckx will change the voltage of bucky at the same time. 181 * 182 */ 183 bool ignore_gpiodvs_side_effect; 184 int buck125_gpios[3]; /* GPIO of [0]SET1, [1]SET2, [2]SET3 */ 185 int buck125_default_idx; /* Default value of SET1, 2, 3 */ 186 unsigned int buck1_voltage[8]; /* buckx_voltage in uV */ 187 bool buck1_gpiodvs; 188 unsigned int buck2_voltage[8]; 189 bool buck2_gpiodvs; 190 unsigned int buck5_voltage[8]; 191 bool buck5_gpiodvs; 192 193 /* ---- Charger control ---- */ 194 /* eoc stands for 'end of charge' */ 195 int eoc_mA; /* 50 ~ 200mA by 10mA step */ 196 /* charge Full Timeout */ 197 int timeout; /* 0 (no timeout), 5, 6, 7 hours */ 198 199 /* ---- MUIC ---- */ 200 struct max8997_muic_platform_data *muic_pdata; 201 202 /* ---- HAPTIC ---- */ 203 struct max8997_haptic_platform_data *haptic_pdata; 204 205 /* RTC: Not implemented */ 206 /* ---- LED ---- */ 207 struct max8997_led_platform_data *led_pdata; 208}; 209 210#endif /* __LINUX_MFD_MAX8997_H */