sdio.h (6127B)
1/* SPDX-License-Identifier: GPL-2.0-or-later */ 2/* 3 * include/linux/mmc/sdio.h 4 * 5 * Copyright 2006-2007 Pierre Ossman 6 */ 7 8#ifndef LINUX_MMC_SDIO_H 9#define LINUX_MMC_SDIO_H 10 11/* SDIO commands type argument response */ 12#define SD_IO_SEND_OP_COND 5 /* bcr [23:0] OCR R4 */ 13#define SD_IO_RW_DIRECT 52 /* ac [31:0] See below R5 */ 14#define SD_IO_RW_EXTENDED 53 /* adtc [31:0] See below R5 */ 15 16/* 17 * SD_IO_RW_DIRECT argument format: 18 * 19 * [31] R/W flag 20 * [30:28] Function number 21 * [27] RAW flag 22 * [25:9] Register address 23 * [7:0] Data 24 */ 25 26/* 27 * SD_IO_RW_EXTENDED argument format: 28 * 29 * [31] R/W flag 30 * [30:28] Function number 31 * [27] Block mode 32 * [26] Increment address 33 * [25:9] Register address 34 * [8:0] Byte/block count 35 */ 36 37#define R4_18V_PRESENT (1<<24) 38#define R4_MEMORY_PRESENT (1 << 27) 39 40/* 41 SDIO status in R5 42 Type 43 e : error bit 44 s : status bit 45 r : detected and set for the actual command response 46 x : detected and set during command execution. the host must poll 47 the card by sending status command in order to read these bits. 48 Clear condition 49 a : according to the card state 50 b : always related to the previous command. Reception of 51 a valid command will clear it (with a delay of one command) 52 c : clear by read 53 */ 54 55#define R5_COM_CRC_ERROR (1 << 15) /* er, b */ 56#define R5_ILLEGAL_COMMAND (1 << 14) /* er, b */ 57#define R5_ERROR (1 << 11) /* erx, c */ 58#define R5_FUNCTION_NUMBER (1 << 9) /* er, c */ 59#define R5_OUT_OF_RANGE (1 << 8) /* er, c */ 60#define R5_STATUS(x) (x & 0xCB00) 61#define R5_IO_CURRENT_STATE(x) ((x & 0x3000) >> 12) /* s, b */ 62 63/* 64 * Card Common Control Registers (CCCR) 65 */ 66 67#define SDIO_CCCR_CCCR 0x00 68 69#define SDIO_CCCR_REV_1_00 0 /* CCCR/FBR Version 1.00 */ 70#define SDIO_CCCR_REV_1_10 1 /* CCCR/FBR Version 1.10 */ 71#define SDIO_CCCR_REV_1_20 2 /* CCCR/FBR Version 1.20 */ 72#define SDIO_CCCR_REV_3_00 3 /* CCCR/FBR Version 3.00 */ 73 74#define SDIO_SDIO_REV_1_00 0 /* SDIO Spec Version 1.00 */ 75#define SDIO_SDIO_REV_1_10 1 /* SDIO Spec Version 1.10 */ 76#define SDIO_SDIO_REV_1_20 2 /* SDIO Spec Version 1.20 */ 77#define SDIO_SDIO_REV_2_00 3 /* SDIO Spec Version 2.00 */ 78#define SDIO_SDIO_REV_3_00 4 /* SDIO Spec Version 3.00 */ 79 80#define SDIO_CCCR_SD 0x01 81 82#define SDIO_SD_REV_1_01 0 /* SD Physical Spec Version 1.01 */ 83#define SDIO_SD_REV_1_10 1 /* SD Physical Spec Version 1.10 */ 84#define SDIO_SD_REV_2_00 2 /* SD Physical Spec Version 2.00 */ 85#define SDIO_SD_REV_3_00 3 /* SD Physical Spec Version 3.00 */ 86 87#define SDIO_CCCR_IOEx 0x02 88#define SDIO_CCCR_IORx 0x03 89 90#define SDIO_CCCR_IENx 0x04 /* Function/Master Interrupt Enable */ 91#define SDIO_CCCR_INTx 0x05 /* Function Interrupt Pending */ 92 93#define SDIO_CCCR_ABORT 0x06 /* function abort/card reset */ 94 95#define SDIO_CCCR_IF 0x07 /* bus interface controls */ 96 97#define SDIO_BUS_WIDTH_MASK 0x03 /* data bus width setting */ 98#define SDIO_BUS_WIDTH_1BIT 0x00 99#define SDIO_BUS_WIDTH_RESERVED 0x01 100#define SDIO_BUS_WIDTH_4BIT 0x02 101#define SDIO_BUS_ECSI 0x20 /* Enable continuous SPI interrupt */ 102#define SDIO_BUS_SCSI 0x40 /* Support continuous SPI interrupt */ 103 104#define SDIO_BUS_ASYNC_INT 0x20 105 106#define SDIO_BUS_CD_DISABLE 0x80 /* disable pull-up on DAT3 (pin 1) */ 107 108#define SDIO_CCCR_CAPS 0x08 109 110#define SDIO_CCCR_CAP_SDC 0x01 /* can do CMD52 while data transfer */ 111#define SDIO_CCCR_CAP_SMB 0x02 /* can do multi-block xfers (CMD53) */ 112#define SDIO_CCCR_CAP_SRW 0x04 /* supports read-wait protocol */ 113#define SDIO_CCCR_CAP_SBS 0x08 /* supports suspend/resume */ 114#define SDIO_CCCR_CAP_S4MI 0x10 /* interrupt during 4-bit CMD53 */ 115#define SDIO_CCCR_CAP_E4MI 0x20 /* enable ints during 4-bit CMD53 */ 116#define SDIO_CCCR_CAP_LSC 0x40 /* low speed card */ 117#define SDIO_CCCR_CAP_4BLS 0x80 /* 4 bit low speed card */ 118 119#define SDIO_CCCR_CIS 0x09 /* common CIS pointer (3 bytes) */ 120 121/* Following 4 regs are valid only if SBS is set */ 122#define SDIO_CCCR_SUSPEND 0x0c 123#define SDIO_CCCR_SELx 0x0d 124#define SDIO_CCCR_EXECx 0x0e 125#define SDIO_CCCR_READYx 0x0f 126 127#define SDIO_CCCR_BLKSIZE 0x10 128 129#define SDIO_CCCR_POWER 0x12 130 131#define SDIO_POWER_SMPC 0x01 /* Supports Master Power Control */ 132#define SDIO_POWER_EMPC 0x02 /* Enable Master Power Control */ 133 134#define SDIO_CCCR_SPEED 0x13 135 136#define SDIO_SPEED_SHS 0x01 /* Supports High-Speed mode */ 137#define SDIO_SPEED_BSS_SHIFT 1 138#define SDIO_SPEED_BSS_MASK (7<<SDIO_SPEED_BSS_SHIFT) 139#define SDIO_SPEED_SDR12 (0<<SDIO_SPEED_BSS_SHIFT) 140#define SDIO_SPEED_SDR25 (1<<SDIO_SPEED_BSS_SHIFT) 141#define SDIO_SPEED_SDR50 (2<<SDIO_SPEED_BSS_SHIFT) 142#define SDIO_SPEED_SDR104 (3<<SDIO_SPEED_BSS_SHIFT) 143#define SDIO_SPEED_DDR50 (4<<SDIO_SPEED_BSS_SHIFT) 144#define SDIO_SPEED_EHS SDIO_SPEED_SDR25 /* Enable High-Speed */ 145 146#define SDIO_CCCR_UHS 0x14 147#define SDIO_UHS_SDR50 0x01 148#define SDIO_UHS_SDR104 0x02 149#define SDIO_UHS_DDR50 0x04 150 151#define SDIO_CCCR_DRIVE_STRENGTH 0x15 152#define SDIO_SDTx_MASK 0x07 153#define SDIO_DRIVE_SDTA (1<<0) 154#define SDIO_DRIVE_SDTC (1<<1) 155#define SDIO_DRIVE_SDTD (1<<2) 156#define SDIO_DRIVE_DTSx_MASK 0x03 157#define SDIO_DRIVE_DTSx_SHIFT 4 158#define SDIO_DTSx_SET_TYPE_B (0 << SDIO_DRIVE_DTSx_SHIFT) 159#define SDIO_DTSx_SET_TYPE_A (1 << SDIO_DRIVE_DTSx_SHIFT) 160#define SDIO_DTSx_SET_TYPE_C (2 << SDIO_DRIVE_DTSx_SHIFT) 161#define SDIO_DTSx_SET_TYPE_D (3 << SDIO_DRIVE_DTSx_SHIFT) 162/* 163 * Function Basic Registers (FBR) 164 */ 165 166#define SDIO_FBR_BASE(f) ((f) * 0x100) /* base of function f's FBRs */ 167 168#define SDIO_FBR_STD_IF 0x00 169 170#define SDIO_FBR_SUPPORTS_CSA 0x40 /* supports Code Storage Area */ 171#define SDIO_FBR_ENABLE_CSA 0x80 /* enable Code Storage Area */ 172 173#define SDIO_FBR_STD_IF_EXT 0x01 174 175#define SDIO_FBR_POWER 0x02 176 177#define SDIO_FBR_POWER_SPS 0x01 /* Supports Power Selection */ 178#define SDIO_FBR_POWER_EPS 0x02 /* Enable (low) Power Selection */ 179 180#define SDIO_FBR_CIS 0x09 /* CIS pointer (3 bytes) */ 181 182 183#define SDIO_FBR_CSA 0x0C /* CSA pointer (3 bytes) */ 184 185#define SDIO_FBR_CSA_DATA 0x0F 186 187#define SDIO_FBR_BLKSIZE 0x10 /* block size (2 bytes) */ 188 189#endif /* LINUX_MMC_SDIO_H */