rio_regs.h (19524B)
1/* SPDX-License-Identifier: GPL-2.0-or-later */ 2/* 3 * RapidIO register definitions 4 * 5 * Copyright 2005 MontaVista Software, Inc. 6 * Matt Porter <mporter@kernel.crashing.org> 7 */ 8 9#ifndef LINUX_RIO_REGS_H 10#define LINUX_RIO_REGS_H 11 12/* 13 * In RapidIO, each device has a 16MB configuration space that is 14 * accessed via maintenance transactions. Portions of configuration 15 * space are standardized and/or reserved. 16 */ 17#define RIO_MAINT_SPACE_SZ 0x1000000 /* 16MB of RapidIO mainenance space */ 18 19#define RIO_DEV_ID_CAR 0x00 /* [I] Device Identity CAR */ 20#define RIO_DEV_INFO_CAR 0x04 /* [I] Device Information CAR */ 21#define RIO_ASM_ID_CAR 0x08 /* [I] Assembly Identity CAR */ 22#define RIO_ASM_ID_MASK 0xffff0000 /* [I] Asm ID Mask */ 23#define RIO_ASM_VEN_ID_MASK 0x0000ffff /* [I] Asm Vend Mask */ 24 25#define RIO_ASM_INFO_CAR 0x0c /* [I] Assembly Information CAR */ 26#define RIO_ASM_REV_MASK 0xffff0000 /* [I] Asm Rev Mask */ 27#define RIO_EXT_FTR_PTR_MASK 0x0000ffff /* [I] EF_PTR Mask */ 28 29#define RIO_PEF_CAR 0x10 /* [I] Processing Element Features CAR */ 30#define RIO_PEF_BRIDGE 0x80000000 /* [I] Bridge */ 31#define RIO_PEF_MEMORY 0x40000000 /* [I] MMIO */ 32#define RIO_PEF_PROCESSOR 0x20000000 /* [I] Processor */ 33#define RIO_PEF_SWITCH 0x10000000 /* [I] Switch */ 34#define RIO_PEF_MULTIPORT 0x08000000 /* [VI, 2.1] Multiport */ 35#define RIO_PEF_INB_MBOX 0x00f00000 /* [II, <= 1.2] Mailboxes */ 36#define RIO_PEF_INB_MBOX0 0x00800000 /* [II, <= 1.2] Mailbox 0 */ 37#define RIO_PEF_INB_MBOX1 0x00400000 /* [II, <= 1.2] Mailbox 1 */ 38#define RIO_PEF_INB_MBOX2 0x00200000 /* [II, <= 1.2] Mailbox 2 */ 39#define RIO_PEF_INB_MBOX3 0x00100000 /* [II, <= 1.2] Mailbox 3 */ 40#define RIO_PEF_INB_DOORBELL 0x00080000 /* [II, <= 1.2] Doorbells */ 41#define RIO_PEF_DEV32 0x00001000 /* [III] PE supports Common TRansport Dev32 */ 42#define RIO_PEF_EXT_RT 0x00000200 /* [III, 1.3] Extended route table support */ 43#define RIO_PEF_STD_RT 0x00000100 /* [III, 1.3] Standard route table support */ 44#define RIO_PEF_CTLS 0x00000010 /* [III] Common Transport Large System (< rev.3) */ 45#define RIO_PEF_DEV16 0x00000010 /* [III] PE Supports Common Transport Dev16 (rev.3) */ 46#define RIO_PEF_EXT_FEATURES 0x00000008 /* [I] EFT_PTR valid */ 47#define RIO_PEF_ADDR_66 0x00000004 /* [I] 66 bits */ 48#define RIO_PEF_ADDR_50 0x00000002 /* [I] 50 bits */ 49#define RIO_PEF_ADDR_34 0x00000001 /* [I] 34 bits */ 50 51#define RIO_SWP_INFO_CAR 0x14 /* [I] Switch Port Information CAR */ 52#define RIO_SWP_INFO_PORT_TOTAL_MASK 0x0000ff00 /* [I] Total number of ports */ 53#define RIO_SWP_INFO_PORT_NUM_MASK 0x000000ff /* [I] Maintenance transaction port number */ 54#define RIO_GET_TOTAL_PORTS(x) ((x & RIO_SWP_INFO_PORT_TOTAL_MASK) >> 8) 55#define RIO_GET_PORT_NUM(x) (x & RIO_SWP_INFO_PORT_NUM_MASK) 56 57#define RIO_SRC_OPS_CAR 0x18 /* [I] Source Operations CAR */ 58#define RIO_SRC_OPS_READ 0x00008000 /* [I] Read op */ 59#define RIO_SRC_OPS_WRITE 0x00004000 /* [I] Write op */ 60#define RIO_SRC_OPS_STREAM_WRITE 0x00002000 /* [I] Str-write op */ 61#define RIO_SRC_OPS_WRITE_RESPONSE 0x00001000 /* [I] Write/resp op */ 62#define RIO_SRC_OPS_DATA_MSG 0x00000800 /* [II] Data msg op */ 63#define RIO_SRC_OPS_DOORBELL 0x00000400 /* [II] Doorbell op */ 64#define RIO_SRC_OPS_ATOMIC_TST_SWP 0x00000100 /* [I] Atomic TAS op */ 65#define RIO_SRC_OPS_ATOMIC_INC 0x00000080 /* [I] Atomic inc op */ 66#define RIO_SRC_OPS_ATOMIC_DEC 0x00000040 /* [I] Atomic dec op */ 67#define RIO_SRC_OPS_ATOMIC_SET 0x00000020 /* [I] Atomic set op */ 68#define RIO_SRC_OPS_ATOMIC_CLR 0x00000010 /* [I] Atomic clr op */ 69#define RIO_SRC_OPS_PORT_WRITE 0x00000004 /* [I] Port-write op */ 70 71#define RIO_DST_OPS_CAR 0x1c /* Destination Operations CAR */ 72#define RIO_DST_OPS_READ 0x00008000 /* [I] Read op */ 73#define RIO_DST_OPS_WRITE 0x00004000 /* [I] Write op */ 74#define RIO_DST_OPS_STREAM_WRITE 0x00002000 /* [I] Str-write op */ 75#define RIO_DST_OPS_WRITE_RESPONSE 0x00001000 /* [I] Write/resp op */ 76#define RIO_DST_OPS_DATA_MSG 0x00000800 /* [II] Data msg op */ 77#define RIO_DST_OPS_DOORBELL 0x00000400 /* [II] Doorbell op */ 78#define RIO_DST_OPS_ATOMIC_TST_SWP 0x00000100 /* [I] Atomic TAS op */ 79#define RIO_DST_OPS_ATOMIC_INC 0x00000080 /* [I] Atomic inc op */ 80#define RIO_DST_OPS_ATOMIC_DEC 0x00000040 /* [I] Atomic dec op */ 81#define RIO_DST_OPS_ATOMIC_SET 0x00000020 /* [I] Atomic set op */ 82#define RIO_DST_OPS_ATOMIC_CLR 0x00000010 /* [I] Atomic clr op */ 83#define RIO_DST_OPS_PORT_WRITE 0x00000004 /* [I] Port-write op */ 84 85#define RIO_OPS_READ 0x00008000 /* [I] Read op */ 86#define RIO_OPS_WRITE 0x00004000 /* [I] Write op */ 87#define RIO_OPS_STREAM_WRITE 0x00002000 /* [I] Str-write op */ 88#define RIO_OPS_WRITE_RESPONSE 0x00001000 /* [I] Write/resp op */ 89#define RIO_OPS_DATA_MSG 0x00000800 /* [II] Data msg op */ 90#define RIO_OPS_DOORBELL 0x00000400 /* [II] Doorbell op */ 91#define RIO_OPS_ATOMIC_TST_SWP 0x00000100 /* [I] Atomic TAS op */ 92#define RIO_OPS_ATOMIC_INC 0x00000080 /* [I] Atomic inc op */ 93#define RIO_OPS_ATOMIC_DEC 0x00000040 /* [I] Atomic dec op */ 94#define RIO_OPS_ATOMIC_SET 0x00000020 /* [I] Atomic set op */ 95#define RIO_OPS_ATOMIC_CLR 0x00000010 /* [I] Atomic clr op */ 96#define RIO_OPS_PORT_WRITE 0x00000004 /* [I] Port-write op */ 97 98 /* 0x20-0x30 *//* Reserved */ 99 100#define RIO_SWITCH_RT_LIMIT 0x34 /* [III, 1.3] Switch Route Table Destination ID Limit CAR */ 101#define RIO_RT_MAX_DESTID 0x0000ffff 102 103#define RIO_MBOX_CSR 0x40 /* [II, <= 1.2] Mailbox CSR */ 104#define RIO_MBOX0_AVAIL 0x80000000 /* [II] Mbox 0 avail */ 105#define RIO_MBOX0_FULL 0x40000000 /* [II] Mbox 0 full */ 106#define RIO_MBOX0_EMPTY 0x20000000 /* [II] Mbox 0 empty */ 107#define RIO_MBOX0_BUSY 0x10000000 /* [II] Mbox 0 busy */ 108#define RIO_MBOX0_FAIL 0x08000000 /* [II] Mbox 0 fail */ 109#define RIO_MBOX0_ERROR 0x04000000 /* [II] Mbox 0 error */ 110#define RIO_MBOX1_AVAIL 0x00800000 /* [II] Mbox 1 avail */ 111#define RIO_MBOX1_FULL 0x00200000 /* [II] Mbox 1 full */ 112#define RIO_MBOX1_EMPTY 0x00200000 /* [II] Mbox 1 empty */ 113#define RIO_MBOX1_BUSY 0x00100000 /* [II] Mbox 1 busy */ 114#define RIO_MBOX1_FAIL 0x00080000 /* [II] Mbox 1 fail */ 115#define RIO_MBOX1_ERROR 0x00040000 /* [II] Mbox 1 error */ 116#define RIO_MBOX2_AVAIL 0x00008000 /* [II] Mbox 2 avail */ 117#define RIO_MBOX2_FULL 0x00004000 /* [II] Mbox 2 full */ 118#define RIO_MBOX2_EMPTY 0x00002000 /* [II] Mbox 2 empty */ 119#define RIO_MBOX2_BUSY 0x00001000 /* [II] Mbox 2 busy */ 120#define RIO_MBOX2_FAIL 0x00000800 /* [II] Mbox 2 fail */ 121#define RIO_MBOX2_ERROR 0x00000400 /* [II] Mbox 2 error */ 122#define RIO_MBOX3_AVAIL 0x00000080 /* [II] Mbox 3 avail */ 123#define RIO_MBOX3_FULL 0x00000040 /* [II] Mbox 3 full */ 124#define RIO_MBOX3_EMPTY 0x00000020 /* [II] Mbox 3 empty */ 125#define RIO_MBOX3_BUSY 0x00000010 /* [II] Mbox 3 busy */ 126#define RIO_MBOX3_FAIL 0x00000008 /* [II] Mbox 3 fail */ 127#define RIO_MBOX3_ERROR 0x00000004 /* [II] Mbox 3 error */ 128 129#define RIO_WRITE_PORT_CSR 0x44 /* [I, <= 1.2] Write Port CSR */ 130#define RIO_DOORBELL_CSR 0x44 /* [II, <= 1.2] Doorbell CSR */ 131#define RIO_DOORBELL_AVAIL 0x80000000 /* [II] Doorbell avail */ 132#define RIO_DOORBELL_FULL 0x40000000 /* [II] Doorbell full */ 133#define RIO_DOORBELL_EMPTY 0x20000000 /* [II] Doorbell empty */ 134#define RIO_DOORBELL_BUSY 0x10000000 /* [II] Doorbell busy */ 135#define RIO_DOORBELL_FAILED 0x08000000 /* [II] Doorbell failed */ 136#define RIO_DOORBELL_ERROR 0x04000000 /* [II] Doorbell error */ 137#define RIO_WRITE_PORT_AVAILABLE 0x00000080 /* [I] Write Port Available */ 138#define RIO_WRITE_PORT_FULL 0x00000040 /* [I] Write Port Full */ 139#define RIO_WRITE_PORT_EMPTY 0x00000020 /* [I] Write Port Empty */ 140#define RIO_WRITE_PORT_BUSY 0x00000010 /* [I] Write Port Busy */ 141#define RIO_WRITE_PORT_FAILED 0x00000008 /* [I] Write Port Failed */ 142#define RIO_WRITE_PORT_ERROR 0x00000004 /* [I] Write Port Error */ 143 144 /* 0x48 *//* Reserved */ 145 146#define RIO_PELL_CTRL_CSR 0x4c /* [I] PE Logical Layer Control CSR */ 147#define RIO_PELL_ADDR_66 0x00000004 /* [I] 66-bit addr */ 148#define RIO_PELL_ADDR_50 0x00000002 /* [I] 50-bit addr */ 149#define RIO_PELL_ADDR_34 0x00000001 /* [I] 34-bit addr */ 150 151 /* 0x50-0x54 *//* Reserved */ 152 153#define RIO_LCSH_BA 0x58 /* [I] LCS High Base Address */ 154#define RIO_LCSL_BA 0x5c /* [I] LCS Base Address */ 155 156#define RIO_DID_CSR 0x60 /* [III] Base Device ID CSR */ 157 158 /* 0x64 *//* Reserved */ 159 160#define RIO_HOST_DID_LOCK_CSR 0x68 /* [III] Host Base Device ID Lock CSR */ 161#define RIO_COMPONENT_TAG_CSR 0x6c /* [III] Component Tag CSR */ 162 163#define RIO_STD_RTE_CONF_DESTID_SEL_CSR 0x70 164#define RIO_STD_RTE_CONF_EXTCFGEN 0x80000000 165#define RIO_STD_RTE_CONF_PORT_SEL_CSR 0x74 166#define RIO_STD_RTE_DEFAULT_PORT 0x78 167 168 /* 0x7c-0xf8 *//* Reserved */ 169 /* 0x100-0xfff8 *//* [I] Extended Features Space */ 170 /* 0x10000-0xfffff8 *//* [I] Implementation-defined Space */ 171 172/* 173 * Extended Features Space is a configuration space area where 174 * functionality is mapped into extended feature blocks via a 175 * singly linked list of extended feature pointers (EFT_PTR). 176 * 177 * Each extended feature block can be identified/located in 178 * Extended Features Space by walking the extended feature 179 * list starting with the Extended Feature Pointer located 180 * in the Assembly Information CAR. 181 * 182 * Extended Feature Blocks (EFBs) are identified with an assigned 183 * EFB ID. Extended feature block offsets in the definitions are 184 * relative to the offset of the EFB within the Extended Features 185 * Space. 186 */ 187 188/* Helper macros to parse the Extended Feature Block header */ 189#define RIO_EFB_PTR_MASK 0xffff0000 190#define RIO_EFB_ID_MASK 0x0000ffff 191#define RIO_GET_BLOCK_PTR(x) ((x & RIO_EFB_PTR_MASK) >> 16) 192#define RIO_GET_BLOCK_ID(x) (x & RIO_EFB_ID_MASK) 193 194/* Extended Feature Block IDs */ 195#define RIO_EFB_SER_EP_M1_ID 0x0001 /* [VI] LP-Serial EP Devices, Map I */ 196#define RIO_EFB_SER_EP_SW_M1_ID 0x0002 /* [VI] LP-Serial EP w SW Recovery Devices, Map I */ 197#define RIO_EFB_SER_EPF_M1_ID 0x0003 /* [VI] LP-Serial EP Free Devices, Map I */ 198#define RIO_EFB_SER_EP_ID 0x0004 /* [VI] LP-Serial EP Devices, RIO 1.2 */ 199#define RIO_EFB_SER_EP_REC_ID 0x0005 /* [VI] LP-Serial EP w SW Recovery Devices, RIO 1.2 */ 200#define RIO_EFB_SER_EP_FREE_ID 0x0006 /* [VI] LP-Serial EP Free Devices, RIO 1.2 */ 201#define RIO_EFB_ERR_MGMNT 0x0007 /* [VIII] Error Management Extensions */ 202#define RIO_EFB_SER_EPF_SW_M1_ID 0x0009 /* [VI] LP-Serial EP Free w SW Recovery Devices, Map I */ 203#define RIO_EFB_SW_ROUTING_TBL 0x000E /* [III] Switch Routing Table Block */ 204#define RIO_EFB_SER_EP_M2_ID 0x0011 /* [VI] LP-Serial EP Devices, Map II */ 205#define RIO_EFB_SER_EP_SW_M2_ID 0x0012 /* [VI] LP-Serial EP w SW Recovery Devices, Map II */ 206#define RIO_EFB_SER_EPF_M2_ID 0x0013 /* [VI] LP-Serial EP Free Devices, Map II */ 207#define RIO_EFB_ERR_MGMNT_HS 0x0017 /* [VIII] Error Management Extensions, Hot-Swap only */ 208#define RIO_EFB_SER_EPF_SW_M2_ID 0x0019 /* [VI] LP-Serial EP Free w SW Recovery Devices, Map II */ 209 210/* 211 * Physical LP-Serial Registers Definitions 212 * Parameters in register macros: 213 * n - port number, m - Register Map Type (1 or 2) 214 */ 215#define RIO_PORT_MNT_HEADER 0x0000 216#define RIO_PORT_REQ_CTL_CSR 0x0020 217#define RIO_PORT_RSP_CTL_CSR 0x0024 218#define RIO_PORT_LINKTO_CTL_CSR 0x0020 219#define RIO_PORT_RSPTO_CTL_CSR 0x0024 220#define RIO_PORT_GEN_CTL_CSR 0x003c 221#define RIO_PORT_GEN_HOST 0x80000000 222#define RIO_PORT_GEN_MASTER 0x40000000 223#define RIO_PORT_GEN_DISCOVERED 0x20000000 224#define RIO_PORT_N_MNT_REQ_CSR(n, m) (0x40 + (n) * (0x20 * (m))) 225#define RIO_MNT_REQ_CMD_RD 0x03 /* Reset-device command */ 226#define RIO_MNT_REQ_CMD_IS 0x04 /* Input-status command */ 227#define RIO_PORT_N_MNT_RSP_CSR(n, m) (0x44 + (n) * (0x20 * (m))) 228#define RIO_PORT_N_MNT_RSP_RVAL 0x80000000 /* Response Valid */ 229#define RIO_PORT_N_MNT_RSP_ASTAT 0x000007e0 /* ackID Status */ 230#define RIO_PORT_N_MNT_RSP_LSTAT 0x0000001f /* Link Status */ 231#define RIO_PORT_N_ACK_STS_CSR(n) (0x48 + (n) * 0x20) /* Only in RM-I */ 232#define RIO_PORT_N_ACK_CLEAR 0x80000000 233#define RIO_PORT_N_ACK_INBOUND 0x3f000000 234#define RIO_PORT_N_ACK_OUTSTAND 0x00003f00 235#define RIO_PORT_N_ACK_OUTBOUND 0x0000003f 236#define RIO_PORT_N_CTL2_CSR(n, m) (0x54 + (n) * (0x20 * (m))) 237#define RIO_PORT_N_CTL2_SEL_BAUD 0xf0000000 238#define RIO_PORT_N_ERR_STS_CSR(n, m) (0x58 + (n) * (0x20 * (m))) 239#define RIO_PORT_N_ERR_STS_OUT_ES 0x00010000 /* Output Error-stopped */ 240#define RIO_PORT_N_ERR_STS_INP_ES 0x00000100 /* Input Error-stopped */ 241#define RIO_PORT_N_ERR_STS_PW_PEND 0x00000010 /* Port-Write Pending */ 242#define RIO_PORT_N_ERR_STS_PORT_UA 0x00000008 /* Port Unavailable */ 243#define RIO_PORT_N_ERR_STS_PORT_ERR 0x00000004 244#define RIO_PORT_N_ERR_STS_PORT_OK 0x00000002 245#define RIO_PORT_N_ERR_STS_PORT_UNINIT 0x00000001 246#define RIO_PORT_N_CTL_CSR(n, m) (0x5c + (n) * (0x20 * (m))) 247#define RIO_PORT_N_CTL_PWIDTH 0xc0000000 248#define RIO_PORT_N_CTL_PWIDTH_1 0x00000000 249#define RIO_PORT_N_CTL_PWIDTH_4 0x40000000 250#define RIO_PORT_N_CTL_IPW 0x38000000 /* Initialized Port Width */ 251#define RIO_PORT_N_CTL_P_TYP_SER 0x00000001 252#define RIO_PORT_N_CTL_LOCKOUT 0x00000002 253#define RIO_PORT_N_CTL_EN_RX 0x00200000 254#define RIO_PORT_N_CTL_EN_TX 0x00400000 255#define RIO_PORT_N_OB_ACK_CSR(n) (0x60 + (n) * 0x40) /* Only in RM-II */ 256#define RIO_PORT_N_OB_ACK_CLEAR 0x80000000 257#define RIO_PORT_N_OB_ACK_OUTSTD 0x00fff000 258#define RIO_PORT_N_OB_ACK_OUTBND 0x00000fff 259#define RIO_PORT_N_IB_ACK_CSR(n) (0x64 + (n) * 0x40) /* Only in RM-II */ 260#define RIO_PORT_N_IB_ACK_INBND 0x00000fff 261 262/* 263 * Device-based helper macros for serial port register access. 264 * d - pointer to rapidio device object, n - port number 265 */ 266 267#define RIO_DEV_PORT_N_MNT_REQ_CSR(d, n) \ 268 (d->phys_efptr + RIO_PORT_N_MNT_REQ_CSR(n, d->phys_rmap)) 269 270#define RIO_DEV_PORT_N_MNT_RSP_CSR(d, n) \ 271 (d->phys_efptr + RIO_PORT_N_MNT_RSP_CSR(n, d->phys_rmap)) 272 273#define RIO_DEV_PORT_N_ACK_STS_CSR(d, n) \ 274 (d->phys_efptr + RIO_PORT_N_ACK_STS_CSR(n)) 275 276#define RIO_DEV_PORT_N_CTL2_CSR(d, n) \ 277 (d->phys_efptr + RIO_PORT_N_CTL2_CSR(n, d->phys_rmap)) 278 279#define RIO_DEV_PORT_N_ERR_STS_CSR(d, n) \ 280 (d->phys_efptr + RIO_PORT_N_ERR_STS_CSR(n, d->phys_rmap)) 281 282#define RIO_DEV_PORT_N_CTL_CSR(d, n) \ 283 (d->phys_efptr + RIO_PORT_N_CTL_CSR(n, d->phys_rmap)) 284 285#define RIO_DEV_PORT_N_OB_ACK_CSR(d, n) \ 286 (d->phys_efptr + RIO_PORT_N_OB_ACK_CSR(n)) 287 288#define RIO_DEV_PORT_N_IB_ACK_CSR(d, n) \ 289 (d->phys_efptr + RIO_PORT_N_IB_ACK_CSR(n)) 290 291/* 292 * Error Management Extensions (RapidIO 1.3+, Part 8) 293 * 294 * Extended Features Block ID=0x0007 295 */ 296 297/* General EM Registers (Common for all Ports) */ 298 299#define RIO_EM_EFB_HEADER 0x000 /* Error Management Extensions Block Header */ 300#define RIO_EM_EMHS_CAR 0x004 /* EM Functionality CAR */ 301#define RIO_EM_LTL_ERR_DETECT 0x008 /* Logical/Transport Layer Error Detect CSR */ 302#define RIO_EM_LTL_ERR_EN 0x00c /* Logical/Transport Layer Error Enable CSR */ 303#define REM_LTL_ERR_ILLTRAN 0x08000000 /* Illegal Transaction decode */ 304#define REM_LTL_ERR_UNSOLR 0x00800000 /* Unsolicited Response */ 305#define REM_LTL_ERR_UNSUPTR 0x00400000 /* Unsupported Transaction */ 306#define REM_LTL_ERR_IMPSPEC 0x000000ff /* Implementation Specific */ 307#define RIO_EM_LTL_HIADDR_CAP 0x010 /* Logical/Transport Layer High Address Capture CSR */ 308#define RIO_EM_LTL_ADDR_CAP 0x014 /* Logical/Transport Layer Address Capture CSR */ 309#define RIO_EM_LTL_DEVID_CAP 0x018 /* Logical/Transport Layer Device ID Capture CSR */ 310#define RIO_EM_LTL_CTRL_CAP 0x01c /* Logical/Transport Layer Control Capture CSR */ 311#define RIO_EM_LTL_DID32_CAP 0x020 /* Logical/Transport Layer Dev32 DestID Capture CSR */ 312#define RIO_EM_LTL_SID32_CAP 0x024 /* Logical/Transport Layer Dev32 source ID Capture CSR */ 313#define RIO_EM_PW_TGT_DEVID 0x028 /* Port-write Target deviceID CSR */ 314#define RIO_EM_PW_TGT_DEVID_D16M 0xff000000 /* Port-write Target DID16 MSB */ 315#define RIO_EM_PW_TGT_DEVID_D8 0x00ff0000 /* Port-write Target DID16 LSB or DID8 */ 316#define RIO_EM_PW_TGT_DEVID_DEV16 0x00008000 /* Port-write Target DID16 LSB or DID8 */ 317#define RIO_EM_PW_TGT_DEVID_DEV32 0x00004000 /* Port-write Target DID16 LSB or DID8 */ 318#define RIO_EM_PKT_TTL 0x02c /* Packet Time-to-live CSR */ 319#define RIO_EM_PKT_TTL_VAL 0xffff0000 /* Packet Time-to-live value */ 320#define RIO_EM_PW_TGT32_DEVID 0x030 /* Port-write Dev32 Target deviceID CSR */ 321#define RIO_EM_PW_TX_CTRL 0x034 /* Port-write Transmission Control CSR */ 322#define RIO_EM_PW_TX_CTRL_PW_DIS 0x00000001 /* Port-write Transmission Disable bit */ 323 324/* Per-Port EM Registers */ 325 326#define RIO_EM_PN_ERR_DETECT(x) (0x040 + x*0x40) /* Port N Error Detect CSR */ 327#define REM_PED_IMPL_SPEC 0x80000000 328#define REM_PED_LINK_OK2U 0x40000000 /* Link OK to Uninit transition */ 329#define REM_PED_LINK_UPDA 0x20000000 /* Link Uninit Packet Discard Active */ 330#define REM_PED_LINK_U2OK 0x10000000 /* Link Uninit to OK transition */ 331#define REM_PED_LINK_TO 0x00000001 332 333#define RIO_EM_PN_ERRRATE_EN(x) (0x044 + x*0x40) /* Port N Error Rate Enable CSR */ 334#define RIO_EM_PN_ERRRATE_EN_OK2U 0x40000000 /* Enable notification for OK2U */ 335#define RIO_EM_PN_ERRRATE_EN_UPDA 0x20000000 /* Enable notification for UPDA */ 336#define RIO_EM_PN_ERRRATE_EN_U2OK 0x10000000 /* Enable notification for U2OK */ 337 338#define RIO_EM_PN_ATTRIB_CAP(x) (0x048 + x*0x40) /* Port N Attributes Capture CSR */ 339#define RIO_EM_PN_PKT_CAP_0(x) (0x04c + x*0x40) /* Port N Packet/Control Symbol Capture 0 CSR */ 340#define RIO_EM_PN_PKT_CAP_1(x) (0x050 + x*0x40) /* Port N Packet Capture 1 CSR */ 341#define RIO_EM_PN_PKT_CAP_2(x) (0x054 + x*0x40) /* Port N Packet Capture 2 CSR */ 342#define RIO_EM_PN_PKT_CAP_3(x) (0x058 + x*0x40) /* Port N Packet Capture 3 CSR */ 343#define RIO_EM_PN_ERRRATE(x) (0x068 + x*0x40) /* Port N Error Rate CSR */ 344#define RIO_EM_PN_ERRRATE_TR(x) (0x06c + x*0x40) /* Port N Error Rate Threshold CSR */ 345#define RIO_EM_PN_LINK_UDT(x) (0x070 + x*0x40) /* Port N Link Uninit Discard Timer CSR */ 346#define RIO_EM_PN_LINK_UDT_TO 0xffffff00 /* Link Uninit Timeout value */ 347 348/* 349 * Switch Routing Table Register Block ID=0x000E (RapidIO 3.0+, part 3) 350 * Register offsets are defined from beginning of the block. 351 */ 352 353/* Broadcast Routing Table Control CSR */ 354#define RIO_BC_RT_CTL_CSR 0x020 355#define RIO_RT_CTL_THREE_LVL 0x80000000 356#define RIO_RT_CTL_DEV32_RT_CTRL 0x40000000 357#define RIO_RT_CTL_MC_MASK_SZ 0x03000000 /* 3.0+ Part 11: Multicast */ 358 359/* Broadcast Level 0 Info CSR */ 360#define RIO_BC_RT_LVL0_INFO_CSR 0x030 361#define RIO_RT_L0I_NUM_GR 0xff000000 362#define RIO_RT_L0I_GR_PTR 0x00fffc00 363 364/* Broadcast Level 1 Info CSR */ 365#define RIO_BC_RT_LVL1_INFO_CSR 0x034 366#define RIO_RT_L1I_NUM_GR 0xff000000 367#define RIO_RT_L1I_GR_PTR 0x00fffc00 368 369/* Broadcast Level 2 Info CSR */ 370#define RIO_BC_RT_LVL2_INFO_CSR 0x038 371#define RIO_RT_L2I_NUM_GR 0xff000000 372#define RIO_RT_L2I_GR_PTR 0x00fffc00 373 374/* Per-Port Routing Table registers. 375 * Register fields defined in the broadcast section above are 376 * applicable to the corresponding registers below. 377 */ 378#define RIO_SPx_RT_CTL_CSR(x) (0x040 + (0x20 * x)) 379#define RIO_SPx_RT_LVL0_INFO_CSR(x) (0x50 + (0x20 * x)) 380#define RIO_SPx_RT_LVL1_INFO_CSR(x) (0x54 + (0x20 * x)) 381#define RIO_SPx_RT_LVL2_INFO_CSR(x) (0x58 + (0x20 * x)) 382 383/* Register Formats for Routing Table Group entry. 384 * Register offsets are calculated using GR_PTR field in the corresponding 385 * table Level_N and group/entry numbers (see RapidIO 3.0+ Part 3). 386 */ 387#define RIO_RT_Ln_ENTRY_IMPL_DEF 0xf0000000 388#define RIO_RT_Ln_ENTRY_RTE_VAL 0x000003ff 389#define RIO_RT_ENTRY_DROP_PKT 0x300 390 391#endif /* LINUX_RIO_REGS_H */