sama7-ddr.h (4018B)
1/* SPDX-License-Identifier: GPL-2.0-only */ 2/* 3 * Microchip SAMA7 UDDR Controller and DDR3 PHY Controller registers offsets 4 * and bit definitions. 5 * 6 * Copyright (C) [2020] Microchip Technology Inc. and its subsidiaries 7 * 8 * Author: Claudu Beznea <claudiu.beznea@microchip.com> 9 */ 10 11#ifndef __SAMA7_DDR_H__ 12#define __SAMA7_DDR_H__ 13 14/* DDR3PHY */ 15#define DDR3PHY_PIR (0x04) /* DDR3PHY PHY Initialization Register */ 16#define DDR3PHY_PIR_DLLBYP (1 << 17) /* DLL Bypass */ 17#define DDR3PHY_PIR_ITMSRST (1 << 4) /* Interface Timing Module Soft Reset */ 18#define DDR3PHY_PIR_DLLLOCK (1 << 2) /* DLL Lock */ 19#define DDR3PHY_PIR_DLLSRST (1 << 1) /* DLL Soft Rest */ 20#define DDR3PHY_PIR_INIT (1 << 0) /* Initialization Trigger */ 21 22#define DDR3PHY_PGCR (0x08) /* DDR3PHY PHY General Configuration Register */ 23#define DDR3PHY_PGCR_CKDV1 (1 << 13) /* CK# Disable Value */ 24#define DDR3PHY_PGCR_CKDV0 (1 << 12) /* CK Disable Value */ 25 26#define DDR3PHY_PGSR (0x0C) /* DDR3PHY PHY General Status Register */ 27#define DDR3PHY_PGSR_IDONE (1 << 0) /* Initialization Done */ 28 29#define DDR3PHY_ACIOCR (0x24) /* DDR3PHY AC I/O Configuration Register */ 30#define DDR3PHY_ACIOCR_CSPDD_CS0 (1 << 18) /* CS#[0] Power Down Driver */ 31#define DDR3PHY_ACIOCR_CKPDD_CK0 (1 << 8) /* CK[0] Power Down Driver */ 32#define DDR3PHY_ACIORC_ACPDD (1 << 3) /* AC Power Down Driver */ 33 34#define DDR3PHY_DXCCR (0x28) /* DDR3PHY DATX8 Common Configuration Register */ 35#define DDR3PHY_DXCCR_DXPDR (1 << 3) /* Data Power Down Receiver */ 36 37#define DDR3PHY_DSGCR (0x2C) /* DDR3PHY DDR System General Configuration Register */ 38#define DDR3PHY_DSGCR_ODTPDD_ODT0 (1 << 20) /* ODT[0] Power Down Driver */ 39 40#define DDR3PHY_ZQ0SR0 (0x188) /* ZQ status register 0 */ 41 42/* UDDRC */ 43#define UDDRC_STAT (0x04) /* UDDRC Operating Mode Status Register */ 44#define UDDRC_STAT_SELFREF_TYPE_DIS (0x0 << 4) /* SDRAM is not in Self-refresh */ 45#define UDDRC_STAT_SELFREF_TYPE_PHY (0x1 << 4) /* SDRAM is in Self-refresh, which was caused by PHY Master Request */ 46#define UDDRC_STAT_SELFREF_TYPE_SW (0x2 << 4) /* SDRAM is in Self-refresh, which was not caused solely under Automatic Self-refresh control */ 47#define UDDRC_STAT_SELFREF_TYPE_AUTO (0x3 << 4) /* SDRAM is in Self-refresh, which was caused by Automatic Self-refresh only */ 48#define UDDRC_STAT_SELFREF_TYPE_MSK (0x3 << 4) /* Self-refresh type mask */ 49#define UDDRC_STAT_OPMODE_INIT (0x0 << 0) /* Init */ 50#define UDDRC_STAT_OPMODE_NORMAL (0x1 << 0) /* Normal */ 51#define UDDRC_STAT_OPMODE_PWRDOWN (0x2 << 0) /* Power-down */ 52#define UDDRC_STAT_OPMODE_SELF_REFRESH (0x3 << 0) /* Self-refresh */ 53#define UDDRC_STAT_OPMODE_MSK (0x7 << 0) /* Operating mode mask */ 54 55#define UDDRC_PWRCTL (0x30) /* UDDRC Low Power Control Register */ 56#define UDDRC_PWRCTL_SELFREF_EN (1 << 0) /* Automatic self-refresh */ 57#define UDDRC_PWRCTL_SELFREF_SW (1 << 5) /* Software self-refresh */ 58 59#define UDDRC_DFIMISC (0x1B0) /* UDDRC DFI Miscellaneous Control Register */ 60#define UDDRC_DFIMISC_DFI_INIT_COMPLETE_EN (1 << 0) /* PHY initialization complete enable signal */ 61 62#define UDDRC_SWCTRL (0x320) /* UDDRC Software Register Programming Control Enable */ 63#define UDDRC_SWCTRL_SW_DONE (1 << 0) /* Enable quasi-dynamic register programming outside reset */ 64 65#define UDDRC_SWSTAT (0x324) /* UDDRC Software Register Programming Control Status */ 66#define UDDRC_SWSTAT_SW_DONE_ACK (1 << 0) /* Register programming done */ 67 68#define UDDRC_PSTAT (0x3FC) /* UDDRC Port Status Register */ 69#define UDDRC_PSTAT_ALL_PORTS (0x1F001F) /* Read + writes outstanding transactions on all ports */ 70 71#define UDDRC_PCTRL_0 (0x490) /* UDDRC Port 0 Control Register */ 72#define UDDRC_PCTRL_1 (0x540) /* UDDRC Port 1 Control Register */ 73#define UDDRC_PCTRL_2 (0x5F0) /* UDDRC Port 2 Control Register */ 74#define UDDRC_PCTRL_3 (0x6A0) /* UDDRC Port 3 Control Register */ 75#define UDDRC_PCTRL_4 (0x750) /* UDDRC Port 4 Control Register */ 76 77#endif /* __SAMA7_DDR_H__ */