shpc.c (25801B)
1#include "qemu/osdep.h" 2#include "qapi/error.h" 3#include "qemu/host-utils.h" 4#include "qemu/range.h" 5#include "qemu/error-report.h" 6#include "hw/pci/shpc.h" 7#include "migration/qemu-file-types.h" 8#include "hw/pci/pci.h" 9#include "hw/pci/pci_bus.h" 10#include "hw/pci/msi.h" 11 12/* TODO: model power only and disabled slot states. */ 13/* TODO: handle SERR and wakeups */ 14/* TODO: consider enabling 66MHz support */ 15 16/* TODO: remove fully only on state DISABLED and LED off. 17 * track state to properly record this. */ 18 19/* SHPC Working Register Set */ 20#define SHPC_BASE_OFFSET 0x00 /* 4 bytes */ 21#define SHPC_SLOTS_33 0x04 /* 4 bytes. Also encodes PCI-X slots. */ 22#define SHPC_SLOTS_66 0x08 /* 4 bytes. */ 23#define SHPC_NSLOTS 0x0C /* 1 byte */ 24#define SHPC_FIRST_DEV 0x0D /* 1 byte */ 25#define SHPC_PHYS_SLOT 0x0E /* 2 byte */ 26#define SHPC_PHYS_NUM_MAX 0x7ff 27#define SHPC_PHYS_NUM_UP 0x2000 28#define SHPC_PHYS_MRL 0x4000 29#define SHPC_PHYS_BUTTON 0x8000 30#define SHPC_SEC_BUS 0x10 /* 2 bytes */ 31#define SHPC_SEC_BUS_33 0x0 32#define SHPC_SEC_BUS_66 0x1 /* Unused */ 33#define SHPC_SEC_BUS_MASK 0x7 34#define SHPC_MSI_CTL 0x12 /* 1 byte */ 35#define SHPC_PROG_IFC 0x13 /* 1 byte */ 36#define SHPC_PROG_IFC_1_0 0x1 37#define SHPC_CMD_CODE 0x14 /* 1 byte */ 38#define SHPC_CMD_TRGT 0x15 /* 1 byte */ 39#define SHPC_CMD_TRGT_MIN 0x1 40#define SHPC_CMD_TRGT_MAX 0x1f 41#define SHPC_CMD_STATUS 0x16 /* 2 bytes */ 42#define SHPC_CMD_STATUS_BUSY 0x1 43#define SHPC_CMD_STATUS_MRL_OPEN 0x2 44#define SHPC_CMD_STATUS_INVALID_CMD 0x4 45#define SHPC_CMD_STATUS_INVALID_MODE 0x8 46#define SHPC_INT_LOCATOR 0x18 /* 4 bytes */ 47#define SHPC_INT_COMMAND 0x1 48#define SHPC_SERR_LOCATOR 0x1C /* 4 bytes */ 49#define SHPC_SERR_INT 0x20 /* 4 bytes */ 50#define SHPC_INT_DIS 0x1 51#define SHPC_SERR_DIS 0x2 52#define SHPC_CMD_INT_DIS 0x4 53#define SHPC_ARB_SERR_DIS 0x8 54#define SHPC_CMD_DETECTED 0x10000 55#define SHPC_ARB_DETECTED 0x20000 56 /* 4 bytes * slot # (start from 0) */ 57#define SHPC_SLOT_REG(s) (0x24 + (s) * 4) 58 /* 2 bytes */ 59#define SHPC_SLOT_STATUS(s) (0x0 + SHPC_SLOT_REG(s)) 60 61/* Same slot state masks are used for command and status registers */ 62#define SHPC_SLOT_STATE_MASK 0x03 63#define SHPC_SLOT_STATE_SHIFT \ 64 ctz32(SHPC_SLOT_STATE_MASK) 65 66#define SHPC_STATE_NO 0x0 67#define SHPC_STATE_PWRONLY 0x1 68#define SHPC_STATE_ENABLED 0x2 69#define SHPC_STATE_DISABLED 0x3 70 71#define SHPC_SLOT_PWR_LED_MASK 0xC 72#define SHPC_SLOT_PWR_LED_SHIFT \ 73 ctz32(SHPC_SLOT_PWR_LED_MASK) 74#define SHPC_SLOT_ATTN_LED_MASK 0x30 75#define SHPC_SLOT_ATTN_LED_SHIFT \ 76 ctz32(SHPC_SLOT_ATTN_LED_MASK) 77 78#define SHPC_LED_NO 0x0 79#define SHPC_LED_ON 0x1 80#define SHPC_LED_BLINK 0x2 81#define SHPC_LED_OFF 0x3 82 83#define SHPC_SLOT_STATUS_PWR_FAULT 0x40 84#define SHPC_SLOT_STATUS_BUTTON 0x80 85#define SHPC_SLOT_STATUS_MRL_OPEN 0x100 86#define SHPC_SLOT_STATUS_66 0x200 87#define SHPC_SLOT_STATUS_PRSNT_MASK 0xC00 88#define SHPC_SLOT_STATUS_PRSNT_EMPTY 0x3 89#define SHPC_SLOT_STATUS_PRSNT_25W 0x1 90#define SHPC_SLOT_STATUS_PRSNT_15W 0x2 91#define SHPC_SLOT_STATUS_PRSNT_7_5W 0x0 92 93#define SHPC_SLOT_STATUS_PRSNT_PCIX 0x3000 94 95 96 /* 1 byte */ 97#define SHPC_SLOT_EVENT_LATCH(s) (0x2 + SHPC_SLOT_REG(s)) 98 /* 1 byte */ 99#define SHPC_SLOT_EVENT_SERR_INT_DIS(d, s) (0x3 + SHPC_SLOT_REG(s)) 100#define SHPC_SLOT_EVENT_PRESENCE 0x01 101#define SHPC_SLOT_EVENT_ISOLATED_FAULT 0x02 102#define SHPC_SLOT_EVENT_BUTTON 0x04 103#define SHPC_SLOT_EVENT_MRL 0x08 104#define SHPC_SLOT_EVENT_CONNECTED_FAULT 0x10 105/* Bits below are used for Serr/Int disable only */ 106#define SHPC_SLOT_EVENT_MRL_SERR_DIS 0x20 107#define SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS 0x40 108 109#define SHPC_MIN_SLOTS 1 110#define SHPC_MAX_SLOTS 31 111#define SHPC_SIZEOF(d) SHPC_SLOT_REG((d)->shpc->nslots) 112 113/* SHPC Slot identifiers */ 114 115/* Hotplug supported at 31 slots out of the total 32. We reserve slot 0, 116 and give the rest of them physical *and* pci numbers starting from 1, so 117 they match logical numbers. Note: this means that multiple slots must have 118 different chassis number values, to make chassis+physical slot unique. 119 TODO: make this configurable? */ 120#define SHPC_IDX_TO_LOGICAL(slot) ((slot) + 1) 121#define SHPC_LOGICAL_TO_IDX(target) ((target) - 1) 122#define SHPC_IDX_TO_PCI(slot) ((slot) + 1) 123#define SHPC_PCI_TO_IDX(pci_slot) ((pci_slot) - 1) 124#define SHPC_IDX_TO_PHYSICAL(slot) ((slot) + 1) 125 126static uint16_t shpc_get_status(SHPCDevice *shpc, int slot, uint16_t msk) 127{ 128 uint8_t *status = shpc->config + SHPC_SLOT_STATUS(slot); 129 return (pci_get_word(status) & msk) >> ctz32(msk); 130} 131 132static void shpc_set_status(SHPCDevice *shpc, 133 int slot, uint8_t value, uint16_t msk) 134{ 135 uint8_t *status = shpc->config + SHPC_SLOT_STATUS(slot); 136 pci_word_test_and_clear_mask(status, msk); 137 pci_word_test_and_set_mask(status, value << ctz32(msk)); 138} 139 140static void shpc_interrupt_update(PCIDevice *d) 141{ 142 SHPCDevice *shpc = d->shpc; 143 int slot; 144 int level = 0; 145 uint32_t serr_int; 146 uint32_t int_locator = 0; 147 148 /* Update interrupt locator register */ 149 for (slot = 0; slot < shpc->nslots; ++slot) { 150 uint8_t event = shpc->config[SHPC_SLOT_EVENT_LATCH(slot)]; 151 uint8_t disable = shpc->config[SHPC_SLOT_EVENT_SERR_INT_DIS(d, slot)]; 152 uint32_t mask = 1U << SHPC_IDX_TO_LOGICAL(slot); 153 if (event & ~disable) { 154 int_locator |= mask; 155 } 156 } 157 serr_int = pci_get_long(shpc->config + SHPC_SERR_INT); 158 if ((serr_int & SHPC_CMD_DETECTED) && !(serr_int & SHPC_CMD_INT_DIS)) { 159 int_locator |= SHPC_INT_COMMAND; 160 } 161 pci_set_long(shpc->config + SHPC_INT_LOCATOR, int_locator); 162 level = (!(serr_int & SHPC_INT_DIS) && int_locator) ? 1 : 0; 163 if (msi_enabled(d) && shpc->msi_requested != level) 164 msi_notify(d, 0); 165 else 166 pci_set_irq(d, level); 167 shpc->msi_requested = level; 168} 169 170static void shpc_set_sec_bus_speed(SHPCDevice *shpc, uint8_t speed) 171{ 172 switch (speed) { 173 case SHPC_SEC_BUS_33: 174 shpc->config[SHPC_SEC_BUS] &= ~SHPC_SEC_BUS_MASK; 175 shpc->config[SHPC_SEC_BUS] |= speed; 176 break; 177 default: 178 pci_word_test_and_set_mask(shpc->config + SHPC_CMD_STATUS, 179 SHPC_CMD_STATUS_INVALID_MODE); 180 } 181} 182 183void shpc_reset(PCIDevice *d) 184{ 185 SHPCDevice *shpc = d->shpc; 186 int nslots = shpc->nslots; 187 int i; 188 memset(shpc->config, 0, SHPC_SIZEOF(d)); 189 pci_set_byte(shpc->config + SHPC_NSLOTS, nslots); 190 pci_set_long(shpc->config + SHPC_SLOTS_33, nslots); 191 pci_set_long(shpc->config + SHPC_SLOTS_66, 0); 192 pci_set_byte(shpc->config + SHPC_FIRST_DEV, SHPC_IDX_TO_PCI(0)); 193 pci_set_word(shpc->config + SHPC_PHYS_SLOT, 194 SHPC_IDX_TO_PHYSICAL(0) | 195 SHPC_PHYS_NUM_UP | 196 SHPC_PHYS_MRL | 197 SHPC_PHYS_BUTTON); 198 pci_set_long(shpc->config + SHPC_SERR_INT, SHPC_INT_DIS | 199 SHPC_SERR_DIS | 200 SHPC_CMD_INT_DIS | 201 SHPC_ARB_SERR_DIS); 202 pci_set_byte(shpc->config + SHPC_PROG_IFC, SHPC_PROG_IFC_1_0); 203 pci_set_word(shpc->config + SHPC_SEC_BUS, SHPC_SEC_BUS_33); 204 for (i = 0; i < shpc->nslots; ++i) { 205 pci_set_byte(shpc->config + SHPC_SLOT_EVENT_SERR_INT_DIS(d, i), 206 SHPC_SLOT_EVENT_PRESENCE | 207 SHPC_SLOT_EVENT_ISOLATED_FAULT | 208 SHPC_SLOT_EVENT_BUTTON | 209 SHPC_SLOT_EVENT_MRL | 210 SHPC_SLOT_EVENT_CONNECTED_FAULT | 211 SHPC_SLOT_EVENT_MRL_SERR_DIS | 212 SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS); 213 if (shpc->sec_bus->devices[PCI_DEVFN(SHPC_IDX_TO_PCI(i), 0)]) { 214 shpc_set_status(shpc, i, SHPC_STATE_ENABLED, SHPC_SLOT_STATE_MASK); 215 shpc_set_status(shpc, i, 0, SHPC_SLOT_STATUS_MRL_OPEN); 216 shpc_set_status(shpc, i, SHPC_SLOT_STATUS_PRSNT_7_5W, 217 SHPC_SLOT_STATUS_PRSNT_MASK); 218 shpc_set_status(shpc, i, SHPC_LED_ON, SHPC_SLOT_PWR_LED_MASK); 219 } else { 220 shpc_set_status(shpc, i, SHPC_STATE_DISABLED, SHPC_SLOT_STATE_MASK); 221 shpc_set_status(shpc, i, 1, SHPC_SLOT_STATUS_MRL_OPEN); 222 shpc_set_status(shpc, i, SHPC_SLOT_STATUS_PRSNT_EMPTY, 223 SHPC_SLOT_STATUS_PRSNT_MASK); 224 shpc_set_status(shpc, i, SHPC_LED_OFF, SHPC_SLOT_PWR_LED_MASK); 225 } 226 shpc_set_status(shpc, i, 0, SHPC_SLOT_STATUS_66); 227 } 228 shpc_set_sec_bus_speed(shpc, SHPC_SEC_BUS_33); 229 shpc->msi_requested = 0; 230 shpc_interrupt_update(d); 231} 232 233static void shpc_invalid_command(SHPCDevice *shpc) 234{ 235 pci_word_test_and_set_mask(shpc->config + SHPC_CMD_STATUS, 236 SHPC_CMD_STATUS_INVALID_CMD); 237} 238 239static void shpc_free_devices_in_slot(SHPCDevice *shpc, int slot) 240{ 241 HotplugHandler *hotplug_ctrl; 242 int devfn; 243 int pci_slot = SHPC_IDX_TO_PCI(slot); 244 for (devfn = PCI_DEVFN(pci_slot, 0); 245 devfn <= PCI_DEVFN(pci_slot, PCI_FUNC_MAX - 1); 246 ++devfn) { 247 PCIDevice *affected_dev = shpc->sec_bus->devices[devfn]; 248 if (affected_dev) { 249 hotplug_ctrl = qdev_get_hotplug_handler(DEVICE(affected_dev)); 250 hotplug_handler_unplug(hotplug_ctrl, DEVICE(affected_dev), 251 &error_abort); 252 object_unparent(OBJECT(affected_dev)); 253 } 254 } 255} 256 257static void shpc_slot_command(SHPCDevice *shpc, uint8_t target, 258 uint8_t state, uint8_t power, uint8_t attn) 259{ 260 uint8_t current_state; 261 int slot = SHPC_LOGICAL_TO_IDX(target); 262 if (target < SHPC_CMD_TRGT_MIN || slot >= shpc->nslots) { 263 shpc_invalid_command(shpc); 264 return; 265 } 266 current_state = shpc_get_status(shpc, slot, SHPC_SLOT_STATE_MASK); 267 if (current_state == SHPC_STATE_ENABLED && state == SHPC_STATE_PWRONLY) { 268 shpc_invalid_command(shpc); 269 return; 270 } 271 272 switch (power) { 273 case SHPC_LED_NO: 274 break; 275 default: 276 /* TODO: send event to monitor */ 277 shpc_set_status(shpc, slot, power, SHPC_SLOT_PWR_LED_MASK); 278 } 279 switch (attn) { 280 case SHPC_LED_NO: 281 break; 282 default: 283 /* TODO: send event to monitor */ 284 shpc_set_status(shpc, slot, attn, SHPC_SLOT_ATTN_LED_MASK); 285 } 286 287 if ((current_state == SHPC_STATE_DISABLED && state == SHPC_STATE_PWRONLY) || 288 (current_state == SHPC_STATE_DISABLED && state == SHPC_STATE_ENABLED)) { 289 shpc_set_status(shpc, slot, state, SHPC_SLOT_STATE_MASK); 290 } else if ((current_state == SHPC_STATE_ENABLED || 291 current_state == SHPC_STATE_PWRONLY) && 292 state == SHPC_STATE_DISABLED) { 293 shpc_set_status(shpc, slot, state, SHPC_SLOT_STATE_MASK); 294 power = shpc_get_status(shpc, slot, SHPC_SLOT_PWR_LED_MASK); 295 /* TODO: track what monitor requested. */ 296 /* Look at LED to figure out whether it's ok to remove the device. */ 297 if (power == SHPC_LED_OFF) { 298 shpc_free_devices_in_slot(shpc, slot); 299 shpc_set_status(shpc, slot, 1, SHPC_SLOT_STATUS_MRL_OPEN); 300 shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_EMPTY, 301 SHPC_SLOT_STATUS_PRSNT_MASK); 302 shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |= 303 SHPC_SLOT_EVENT_MRL | 304 SHPC_SLOT_EVENT_PRESENCE; 305 } 306 } 307} 308 309static void shpc_command(SHPCDevice *shpc) 310{ 311 uint8_t code = pci_get_byte(shpc->config + SHPC_CMD_CODE); 312 uint8_t speed; 313 uint8_t target; 314 uint8_t attn; 315 uint8_t power; 316 uint8_t state; 317 int i; 318 319 /* Clear status from the previous command. */ 320 pci_word_test_and_clear_mask(shpc->config + SHPC_CMD_STATUS, 321 SHPC_CMD_STATUS_BUSY | 322 SHPC_CMD_STATUS_MRL_OPEN | 323 SHPC_CMD_STATUS_INVALID_CMD | 324 SHPC_CMD_STATUS_INVALID_MODE); 325 switch (code) { 326 case 0x00 ... 0x3f: 327 target = shpc->config[SHPC_CMD_TRGT] & SHPC_CMD_TRGT_MAX; 328 state = (code & SHPC_SLOT_STATE_MASK) >> SHPC_SLOT_STATE_SHIFT; 329 power = (code & SHPC_SLOT_PWR_LED_MASK) >> SHPC_SLOT_PWR_LED_SHIFT; 330 attn = (code & SHPC_SLOT_ATTN_LED_MASK) >> SHPC_SLOT_ATTN_LED_SHIFT; 331 shpc_slot_command(shpc, target, state, power, attn); 332 break; 333 case 0x40 ... 0x47: 334 speed = code & SHPC_SEC_BUS_MASK; 335 shpc_set_sec_bus_speed(shpc, speed); 336 break; 337 case 0x48: 338 /* Power only all slots */ 339 /* first verify no slots are enabled */ 340 for (i = 0; i < shpc->nslots; ++i) { 341 state = shpc_get_status(shpc, i, SHPC_SLOT_STATE_MASK); 342 if (state == SHPC_STATE_ENABLED) { 343 shpc_invalid_command(shpc); 344 goto done; 345 } 346 } 347 for (i = 0; i < shpc->nslots; ++i) { 348 if (!(shpc_get_status(shpc, i, SHPC_SLOT_STATUS_MRL_OPEN))) { 349 shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN, 350 SHPC_STATE_PWRONLY, SHPC_LED_ON, SHPC_LED_NO); 351 } else { 352 shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN, 353 SHPC_STATE_NO, SHPC_LED_OFF, SHPC_LED_NO); 354 } 355 } 356 break; 357 case 0x49: 358 /* Enable all slots */ 359 /* TODO: Spec says this shall fail if some are already enabled. 360 * This doesn't make sense - why not? a spec bug? */ 361 for (i = 0; i < shpc->nslots; ++i) { 362 state = shpc_get_status(shpc, i, SHPC_SLOT_STATE_MASK); 363 if (state == SHPC_STATE_ENABLED) { 364 shpc_invalid_command(shpc); 365 goto done; 366 } 367 } 368 for (i = 0; i < shpc->nslots; ++i) { 369 if (!(shpc_get_status(shpc, i, SHPC_SLOT_STATUS_MRL_OPEN))) { 370 shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN, 371 SHPC_STATE_ENABLED, SHPC_LED_ON, SHPC_LED_NO); 372 } else { 373 shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN, 374 SHPC_STATE_NO, SHPC_LED_OFF, SHPC_LED_NO); 375 } 376 } 377 break; 378 default: 379 shpc_invalid_command(shpc); 380 break; 381 } 382done: 383 pci_long_test_and_set_mask(shpc->config + SHPC_SERR_INT, SHPC_CMD_DETECTED); 384} 385 386static void shpc_write(PCIDevice *d, unsigned addr, uint64_t val, int l) 387{ 388 SHPCDevice *shpc = d->shpc; 389 int i; 390 if (addr >= SHPC_SIZEOF(d)) { 391 return; 392 } 393 l = MIN(l, SHPC_SIZEOF(d) - addr); 394 395 /* TODO: code duplicated from pci.c */ 396 for (i = 0; i < l; val >>= 8, ++i) { 397 unsigned a = addr + i; 398 uint8_t wmask = shpc->wmask[a]; 399 uint8_t w1cmask = shpc->w1cmask[a]; 400 assert(!(wmask & w1cmask)); 401 shpc->config[a] = (shpc->config[a] & ~wmask) | (val & wmask); 402 shpc->config[a] &= ~(val & w1cmask); /* W1C: Write 1 to Clear */ 403 } 404 if (ranges_overlap(addr, l, SHPC_CMD_CODE, 2)) { 405 shpc_command(shpc); 406 } 407 shpc_interrupt_update(d); 408} 409 410static uint64_t shpc_read(PCIDevice *d, unsigned addr, int l) 411{ 412 uint64_t val = 0x0; 413 if (addr >= SHPC_SIZEOF(d)) { 414 return val; 415 } 416 l = MIN(l, SHPC_SIZEOF(d) - addr); 417 memcpy(&val, d->shpc->config + addr, l); 418 return val; 419} 420 421/* SHPC Bridge Capability */ 422#define SHPC_CAP_LENGTH 0x08 423#define SHPC_CAP_DWORD_SELECT 0x2 /* 1 byte */ 424#define SHPC_CAP_CxP 0x3 /* 1 byte: CSP, CIP */ 425#define SHPC_CAP_DWORD_DATA 0x4 /* 4 bytes */ 426#define SHPC_CAP_CSP_MASK 0x4 427#define SHPC_CAP_CIP_MASK 0x8 428 429static uint8_t shpc_cap_dword(PCIDevice *d) 430{ 431 return pci_get_byte(d->config + d->shpc->cap + SHPC_CAP_DWORD_SELECT); 432} 433 434/* Update dword data capability register */ 435static void shpc_cap_update_dword(PCIDevice *d) 436{ 437 unsigned data; 438 data = shpc_read(d, shpc_cap_dword(d) * 4, 4); 439 pci_set_long(d->config + d->shpc->cap + SHPC_CAP_DWORD_DATA, data); 440} 441 442/* Add SHPC capability to the config space for the device. */ 443static int shpc_cap_add_config(PCIDevice *d, Error **errp) 444{ 445 uint8_t *config; 446 int config_offset; 447 config_offset = pci_add_capability(d, PCI_CAP_ID_SHPC, 448 0, SHPC_CAP_LENGTH, 449 errp); 450 if (config_offset < 0) { 451 return config_offset; 452 } 453 config = d->config + config_offset; 454 455 pci_set_byte(config + SHPC_CAP_DWORD_SELECT, 0); 456 pci_set_byte(config + SHPC_CAP_CxP, 0); 457 pci_set_long(config + SHPC_CAP_DWORD_DATA, 0); 458 d->shpc->cap = config_offset; 459 /* Make dword select and data writeable. */ 460 pci_set_byte(d->wmask + config_offset + SHPC_CAP_DWORD_SELECT, 0xff); 461 pci_set_long(d->wmask + config_offset + SHPC_CAP_DWORD_DATA, 0xffffffff); 462 return 0; 463} 464 465static uint64_t shpc_mmio_read(void *opaque, hwaddr addr, 466 unsigned size) 467{ 468 return shpc_read(opaque, addr, size); 469} 470 471static void shpc_mmio_write(void *opaque, hwaddr addr, 472 uint64_t val, unsigned size) 473{ 474 shpc_write(opaque, addr, val, size); 475} 476 477static const MemoryRegionOps shpc_mmio_ops = { 478 .read = shpc_mmio_read, 479 .write = shpc_mmio_write, 480 .endianness = DEVICE_LITTLE_ENDIAN, 481 .valid = { 482 /* SHPC ECN requires dword accesses, but the original 1.0 spec doesn't. 483 * It's easier to suppport all sizes than worry about it. */ 484 .min_access_size = 1, 485 .max_access_size = 4, 486 }, 487}; 488static void shpc_device_plug_common(PCIDevice *affected_dev, int *slot, 489 SHPCDevice *shpc, Error **errp) 490{ 491 int pci_slot = PCI_SLOT(affected_dev->devfn); 492 *slot = SHPC_PCI_TO_IDX(pci_slot); 493 494 if (pci_slot < SHPC_IDX_TO_PCI(0) || *slot >= shpc->nslots) { 495 error_setg(errp, "Unsupported PCI slot %d for standard hotplug " 496 "controller. Valid slots are between %d and %d.", 497 pci_slot, SHPC_IDX_TO_PCI(0), 498 SHPC_IDX_TO_PCI(shpc->nslots) - 1); 499 return; 500 } 501} 502 503void shpc_device_plug_cb(HotplugHandler *hotplug_dev, DeviceState *dev, 504 Error **errp) 505{ 506 Error *local_err = NULL; 507 PCIDevice *pci_hotplug_dev = PCI_DEVICE(hotplug_dev); 508 SHPCDevice *shpc = pci_hotplug_dev->shpc; 509 int slot; 510 511 shpc_device_plug_common(PCI_DEVICE(dev), &slot, shpc, &local_err); 512 if (local_err) { 513 error_propagate(errp, local_err); 514 return; 515 } 516 517 /* Don't send event when device is enabled during qemu machine creation: 518 * it is present on boot, no hotplug event is necessary. We do send an 519 * event when the device is disabled later. */ 520 if (!dev->hotplugged) { 521 shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_MRL_OPEN); 522 shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_7_5W, 523 SHPC_SLOT_STATUS_PRSNT_MASK); 524 return; 525 } 526 527 /* This could be a cancellation of the previous removal. 528 * We check MRL state to figure out. */ 529 if (shpc_get_status(shpc, slot, SHPC_SLOT_STATUS_MRL_OPEN)) { 530 shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_MRL_OPEN); 531 shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_7_5W, 532 SHPC_SLOT_STATUS_PRSNT_MASK); 533 shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |= 534 SHPC_SLOT_EVENT_BUTTON | 535 SHPC_SLOT_EVENT_MRL | 536 SHPC_SLOT_EVENT_PRESENCE; 537 } else { 538 /* Press attention button to cancel removal */ 539 shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |= 540 SHPC_SLOT_EVENT_BUTTON; 541 } 542 shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_66); 543 shpc_interrupt_update(pci_hotplug_dev); 544} 545 546void shpc_device_unplug_cb(HotplugHandler *hotplug_dev, DeviceState *dev, 547 Error **errp) 548{ 549 qdev_unrealize(dev); 550} 551 552void shpc_device_unplug_request_cb(HotplugHandler *hotplug_dev, 553 DeviceState *dev, Error **errp) 554{ 555 Error *local_err = NULL; 556 PCIDevice *pci_hotplug_dev = PCI_DEVICE(hotplug_dev); 557 SHPCDevice *shpc = pci_hotplug_dev->shpc; 558 uint8_t state; 559 uint8_t led; 560 int slot; 561 562 shpc_device_plug_common(PCI_DEVICE(dev), &slot, shpc, &local_err); 563 if (local_err) { 564 error_propagate(errp, local_err); 565 return; 566 } 567 568 state = shpc_get_status(shpc, slot, SHPC_SLOT_STATE_MASK); 569 led = shpc_get_status(shpc, slot, SHPC_SLOT_PWR_LED_MASK); 570 if (state == SHPC_STATE_DISABLED && led == SHPC_LED_OFF) { 571 shpc_free_devices_in_slot(shpc, slot); 572 shpc_set_status(shpc, slot, 1, SHPC_SLOT_STATUS_MRL_OPEN); 573 shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_EMPTY, 574 SHPC_SLOT_STATUS_PRSNT_MASK); 575 shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |= 576 SHPC_SLOT_EVENT_MRL | 577 SHPC_SLOT_EVENT_PRESENCE; 578 } else { 579 shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |= SHPC_SLOT_EVENT_BUTTON; 580 } 581 shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_66); 582 shpc_interrupt_update(pci_hotplug_dev); 583} 584 585/* Initialize the SHPC structure in bridge's BAR. */ 586int shpc_init(PCIDevice *d, PCIBus *sec_bus, MemoryRegion *bar, 587 unsigned offset, Error **errp) 588{ 589 int i, ret; 590 int nslots = SHPC_MAX_SLOTS; /* TODO: qdev property? */ 591 SHPCDevice *shpc = d->shpc = g_malloc0(sizeof(*d->shpc)); 592 shpc->sec_bus = sec_bus; 593 ret = shpc_cap_add_config(d, errp); 594 if (ret) { 595 g_free(d->shpc); 596 return ret; 597 } 598 if (nslots < SHPC_MIN_SLOTS) { 599 return 0; 600 } 601 if (nslots > SHPC_MAX_SLOTS || 602 SHPC_IDX_TO_PCI(nslots) > PCI_SLOT_MAX) { 603 /* TODO: report an error mesage that makes sense. */ 604 return -EINVAL; 605 } 606 shpc->nslots = nslots; 607 shpc->config = g_malloc0(SHPC_SIZEOF(d)); 608 shpc->cmask = g_malloc0(SHPC_SIZEOF(d)); 609 shpc->wmask = g_malloc0(SHPC_SIZEOF(d)); 610 shpc->w1cmask = g_malloc0(SHPC_SIZEOF(d)); 611 612 shpc_reset(d); 613 614 pci_set_long(shpc->config + SHPC_BASE_OFFSET, offset); 615 616 pci_set_byte(shpc->wmask + SHPC_CMD_CODE, 0xff); 617 pci_set_byte(shpc->wmask + SHPC_CMD_TRGT, SHPC_CMD_TRGT_MAX); 618 pci_set_byte(shpc->wmask + SHPC_CMD_TRGT, SHPC_CMD_TRGT_MAX); 619 pci_set_long(shpc->wmask + SHPC_SERR_INT, 620 SHPC_INT_DIS | 621 SHPC_SERR_DIS | 622 SHPC_CMD_INT_DIS | 623 SHPC_ARB_SERR_DIS); 624 pci_set_long(shpc->w1cmask + SHPC_SERR_INT, 625 SHPC_CMD_DETECTED | 626 SHPC_ARB_DETECTED); 627 for (i = 0; i < nslots; ++i) { 628 pci_set_byte(shpc->wmask + 629 SHPC_SLOT_EVENT_SERR_INT_DIS(d, i), 630 SHPC_SLOT_EVENT_PRESENCE | 631 SHPC_SLOT_EVENT_ISOLATED_FAULT | 632 SHPC_SLOT_EVENT_BUTTON | 633 SHPC_SLOT_EVENT_MRL | 634 SHPC_SLOT_EVENT_CONNECTED_FAULT | 635 SHPC_SLOT_EVENT_MRL_SERR_DIS | 636 SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS); 637 pci_set_byte(shpc->w1cmask + 638 SHPC_SLOT_EVENT_LATCH(i), 639 SHPC_SLOT_EVENT_PRESENCE | 640 SHPC_SLOT_EVENT_ISOLATED_FAULT | 641 SHPC_SLOT_EVENT_BUTTON | 642 SHPC_SLOT_EVENT_MRL | 643 SHPC_SLOT_EVENT_CONNECTED_FAULT); 644 } 645 646 /* TODO: init cmask */ 647 memory_region_init_io(&shpc->mmio, OBJECT(d), &shpc_mmio_ops, 648 d, "shpc-mmio", SHPC_SIZEOF(d)); 649 shpc_cap_update_dword(d); 650 memory_region_add_subregion(bar, offset, &shpc->mmio); 651 652 qbus_set_hotplug_handler(BUS(sec_bus), OBJECT(d)); 653 654 d->cap_present |= QEMU_PCI_CAP_SHPC; 655 return 0; 656} 657 658int shpc_bar_size(PCIDevice *d) 659{ 660 return pow2roundup32(SHPC_SLOT_REG(SHPC_MAX_SLOTS)); 661} 662 663void shpc_cleanup(PCIDevice *d, MemoryRegion *bar) 664{ 665 SHPCDevice *shpc = d->shpc; 666 d->cap_present &= ~QEMU_PCI_CAP_SHPC; 667 memory_region_del_subregion(bar, &shpc->mmio); 668 /* TODO: cleanup config space changes? */ 669} 670 671void shpc_free(PCIDevice *d) 672{ 673 SHPCDevice *shpc = d->shpc; 674 if (!shpc) { 675 return; 676 } 677 object_unparent(OBJECT(&shpc->mmio)); 678 g_free(shpc->config); 679 g_free(shpc->cmask); 680 g_free(shpc->wmask); 681 g_free(shpc->w1cmask); 682 g_free(shpc); 683 d->shpc = NULL; 684} 685 686void shpc_cap_write_config(PCIDevice *d, uint32_t addr, uint32_t val, int l) 687{ 688 if (!ranges_overlap(addr, l, d->shpc->cap, SHPC_CAP_LENGTH)) { 689 return; 690 } 691 if (ranges_overlap(addr, l, d->shpc->cap + SHPC_CAP_DWORD_DATA, 4)) { 692 unsigned dword_data; 693 dword_data = pci_get_long(d->shpc->config + d->shpc->cap 694 + SHPC_CAP_DWORD_DATA); 695 shpc_write(d, shpc_cap_dword(d) * 4, dword_data, 4); 696 } 697 /* Update cap dword data in case guest is going to read it. */ 698 shpc_cap_update_dword(d); 699} 700 701static int shpc_save(QEMUFile *f, void *pv, size_t size, 702 const VMStateField *field, JSONWriter *vmdesc) 703{ 704 PCIDevice *d = container_of(pv, PCIDevice, shpc); 705 qemu_put_buffer(f, d->shpc->config, SHPC_SIZEOF(d)); 706 707 return 0; 708} 709 710static int shpc_load(QEMUFile *f, void *pv, size_t size, 711 const VMStateField *field) 712{ 713 PCIDevice *d = container_of(pv, PCIDevice, shpc); 714 int ret = qemu_get_buffer(f, d->shpc->config, SHPC_SIZEOF(d)); 715 if (ret != SHPC_SIZEOF(d)) { 716 return -EINVAL; 717 } 718 /* Make sure we don't lose notifications. An extra interrupt is harmless. */ 719 d->shpc->msi_requested = 0; 720 shpc_interrupt_update(d); 721 return 0; 722} 723 724VMStateInfo shpc_vmstate_info = { 725 .name = "shpc", 726 .get = shpc_load, 727 .put = shpc_save, 728};