aspeed_smc.c (56415B)
1/* 2 * ASPEED AST2400 SMC Controller (SPI Flash Only) 3 * 4 * Copyright (C) 2016 IBM Corp. 5 * 6 * Permission is hereby granted, free of charge, to any person obtaining a copy 7 * of this software and associated documentation files (the "Software"), to deal 8 * in the Software without restriction, including without limitation the rights 9 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell 10 * copies of the Software, and to permit persons to whom the Software is 11 * furnished to do so, subject to the following conditions: 12 * 13 * The above copyright notice and this permission notice shall be included in 14 * all copies or substantial portions of the Software. 15 * 16 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR 17 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, 18 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL 19 * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER 20 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, 21 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN 22 * THE SOFTWARE. 23 */ 24 25#include "qemu/osdep.h" 26#include "hw/sysbus.h" 27#include "migration/vmstate.h" 28#include "qemu/log.h" 29#include "qemu/module.h" 30#include "qemu/error-report.h" 31#include "qapi/error.h" 32#include "qemu/units.h" 33#include "trace.h" 34 35#include "hw/irq.h" 36#include "hw/qdev-properties.h" 37#include "hw/ssi/aspeed_smc.h" 38 39/* CE Type Setting Register */ 40#define R_CONF (0x00 / 4) 41#define CONF_LEGACY_DISABLE (1 << 31) 42#define CONF_ENABLE_W4 20 43#define CONF_ENABLE_W3 19 44#define CONF_ENABLE_W2 18 45#define CONF_ENABLE_W1 17 46#define CONF_ENABLE_W0 16 47#define CONF_FLASH_TYPE4 8 48#define CONF_FLASH_TYPE3 6 49#define CONF_FLASH_TYPE2 4 50#define CONF_FLASH_TYPE1 2 51#define CONF_FLASH_TYPE0 0 52#define CONF_FLASH_TYPE_NOR 0x0 53#define CONF_FLASH_TYPE_NAND 0x1 54#define CONF_FLASH_TYPE_SPI 0x2 /* AST2600 is SPI only */ 55 56/* CE Control Register */ 57#define R_CE_CTRL (0x04 / 4) 58#define CTRL_EXTENDED4 4 /* 32 bit addressing for SPI */ 59#define CTRL_EXTENDED3 3 /* 32 bit addressing for SPI */ 60#define CTRL_EXTENDED2 2 /* 32 bit addressing for SPI */ 61#define CTRL_EXTENDED1 1 /* 32 bit addressing for SPI */ 62#define CTRL_EXTENDED0 0 /* 32 bit addressing for SPI */ 63 64/* Interrupt Control and Status Register */ 65#define R_INTR_CTRL (0x08 / 4) 66#define INTR_CTRL_DMA_STATUS (1 << 11) 67#define INTR_CTRL_CMD_ABORT_STATUS (1 << 10) 68#define INTR_CTRL_WRITE_PROTECT_STATUS (1 << 9) 69#define INTR_CTRL_DMA_EN (1 << 3) 70#define INTR_CTRL_CMD_ABORT_EN (1 << 2) 71#define INTR_CTRL_WRITE_PROTECT_EN (1 << 1) 72 73/* Command Control Register */ 74#define R_CE_CMD_CTRL (0x0C / 4) 75#define CTRL_ADDR_BYTE0_DISABLE_SHIFT 4 76#define CTRL_DATA_BYTE0_DISABLE_SHIFT 0 77 78#define aspeed_smc_addr_byte_enabled(s, i) \ 79 (!((s)->regs[R_CE_CMD_CTRL] & (1 << (CTRL_ADDR_BYTE0_DISABLE_SHIFT + (i))))) 80#define aspeed_smc_data_byte_enabled(s, i) \ 81 (!((s)->regs[R_CE_CMD_CTRL] & (1 << (CTRL_DATA_BYTE0_DISABLE_SHIFT + (i))))) 82 83/* CEx Control Register */ 84#define R_CTRL0 (0x10 / 4) 85#define CTRL_IO_QPI (1 << 31) 86#define CTRL_IO_QUAD_DATA (1 << 30) 87#define CTRL_IO_DUAL_DATA (1 << 29) 88#define CTRL_IO_DUAL_ADDR_DATA (1 << 28) /* Includes dummies */ 89#define CTRL_IO_QUAD_ADDR_DATA (1 << 28) /* Includes dummies */ 90#define CTRL_CMD_SHIFT 16 91#define CTRL_CMD_MASK 0xff 92#define CTRL_DUMMY_HIGH_SHIFT 14 93#define CTRL_AST2400_SPI_4BYTE (1 << 13) 94#define CE_CTRL_CLOCK_FREQ_SHIFT 8 95#define CE_CTRL_CLOCK_FREQ_MASK 0xf 96#define CE_CTRL_CLOCK_FREQ(div) \ 97 (((div) & CE_CTRL_CLOCK_FREQ_MASK) << CE_CTRL_CLOCK_FREQ_SHIFT) 98#define CTRL_DUMMY_LOW_SHIFT 6 /* 2 bits [7:6] */ 99#define CTRL_CE_STOP_ACTIVE (1 << 2) 100#define CTRL_CMD_MODE_MASK 0x3 101#define CTRL_READMODE 0x0 102#define CTRL_FREADMODE 0x1 103#define CTRL_WRITEMODE 0x2 104#define CTRL_USERMODE 0x3 105#define R_CTRL1 (0x14 / 4) 106#define R_CTRL2 (0x18 / 4) 107#define R_CTRL3 (0x1C / 4) 108#define R_CTRL4 (0x20 / 4) 109 110/* CEx Segment Address Register */ 111#define R_SEG_ADDR0 (0x30 / 4) 112#define SEG_END_SHIFT 24 /* 8MB units */ 113#define SEG_END_MASK 0xff 114#define SEG_START_SHIFT 16 /* address bit [A29-A23] */ 115#define SEG_START_MASK 0xff 116#define R_SEG_ADDR1 (0x34 / 4) 117#define R_SEG_ADDR2 (0x38 / 4) 118#define R_SEG_ADDR3 (0x3C / 4) 119#define R_SEG_ADDR4 (0x40 / 4) 120 121/* Misc Control Register #1 */ 122#define R_MISC_CTRL1 (0x50 / 4) 123 124/* SPI dummy cycle data */ 125#define R_DUMMY_DATA (0x54 / 4) 126 127/* FMC_WDT2 Control/Status Register for Alternate Boot (AST2600) */ 128#define R_FMC_WDT2_CTRL (0x64 / 4) 129#define FMC_WDT2_CTRL_ALT_BOOT_MODE BIT(6) /* O: 2 chips 1: 1 chip */ 130#define FMC_WDT2_CTRL_SINGLE_BOOT_MODE BIT(5) 131#define FMC_WDT2_CTRL_BOOT_SOURCE BIT(4) /* O: primary 1: alternate */ 132#define FMC_WDT2_CTRL_EN BIT(0) 133 134/* DMA Control/Status Register */ 135#define R_DMA_CTRL (0x80 / 4) 136#define DMA_CTRL_REQUEST (1 << 31) 137#define DMA_CTRL_GRANT (1 << 30) 138#define DMA_CTRL_DELAY_MASK 0xf 139#define DMA_CTRL_DELAY_SHIFT 8 140#define DMA_CTRL_FREQ_MASK 0xf 141#define DMA_CTRL_FREQ_SHIFT 4 142#define DMA_CTRL_CALIB (1 << 3) 143#define DMA_CTRL_CKSUM (1 << 2) 144#define DMA_CTRL_WRITE (1 << 1) 145#define DMA_CTRL_ENABLE (1 << 0) 146 147/* DMA Flash Side Address */ 148#define R_DMA_FLASH_ADDR (0x84 / 4) 149 150/* DMA DRAM Side Address */ 151#define R_DMA_DRAM_ADDR (0x88 / 4) 152 153/* DMA Length Register */ 154#define R_DMA_LEN (0x8C / 4) 155 156/* Checksum Calculation Result */ 157#define R_DMA_CHECKSUM (0x90 / 4) 158 159/* Read Timing Compensation Register */ 160#define R_TIMINGS (0x94 / 4) 161 162/* SPI controller registers and bits (AST2400) */ 163#define R_SPI_CONF (0x00 / 4) 164#define SPI_CONF_ENABLE_W0 0 165#define R_SPI_CTRL0 (0x4 / 4) 166#define R_SPI_MISC_CTRL (0x10 / 4) 167#define R_SPI_TIMINGS (0x14 / 4) 168 169#define ASPEED_SMC_R_SPI_MAX (0x20 / 4) 170#define ASPEED_SMC_R_SMC_MAX (0x20 / 4) 171 172/* 173 * DMA DRAM addresses should be 4 bytes aligned and the valid address 174 * range is 0x40000000 - 0x5FFFFFFF (AST2400) 175 * 0x80000000 - 0xBFFFFFFF (AST2500) 176 * 177 * DMA flash addresses should be 4 bytes aligned and the valid address 178 * range is 0x20000000 - 0x2FFFFFFF. 179 * 180 * DMA length is from 4 bytes to 32MB 181 * 0: 4 bytes 182 * 0x7FFFFF: 32M bytes 183 */ 184#define DMA_DRAM_ADDR(asc, val) ((val) & (asc)->dma_dram_mask) 185#define DMA_FLASH_ADDR(asc, val) ((val) & (asc)->dma_flash_mask) 186#define DMA_LENGTH(val) ((val) & 0x01FFFFFC) 187 188/* Flash opcodes. */ 189#define SPI_OP_READ 0x03 /* Read data bytes (low frequency) */ 190 191#define SNOOP_OFF 0xFF 192#define SNOOP_START 0x0 193 194/* 195 * Default segments mapping addresses and size for each peripheral per 196 * controller. These can be changed when board is initialized with the 197 * Segment Address Registers. 198 */ 199static const AspeedSegments aspeed_2500_spi1_segments[]; 200static const AspeedSegments aspeed_2500_spi2_segments[]; 201 202#define ASPEED_SMC_FEATURE_DMA 0x1 203#define ASPEED_SMC_FEATURE_DMA_GRANT 0x2 204#define ASPEED_SMC_FEATURE_WDT_CONTROL 0x4 205 206static inline bool aspeed_smc_has_dma(const AspeedSMCClass *asc) 207{ 208 return !!(asc->features & ASPEED_SMC_FEATURE_DMA); 209} 210 211static inline bool aspeed_smc_has_wdt_control(const AspeedSMCClass *asc) 212{ 213 return !!(asc->features & ASPEED_SMC_FEATURE_WDT_CONTROL); 214} 215 216#define aspeed_smc_error(fmt, ...) \ 217 qemu_log_mask(LOG_GUEST_ERROR, "%s: " fmt "\n", __func__, ## __VA_ARGS__) 218 219static bool aspeed_smc_flash_overlap(const AspeedSMCState *s, 220 const AspeedSegments *new, 221 int cs) 222{ 223 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 224 AspeedSegments seg; 225 int i; 226 227 for (i = 0; i < asc->max_peripherals; i++) { 228 if (i == cs) { 229 continue; 230 } 231 232 asc->reg_to_segment(s, s->regs[R_SEG_ADDR0 + i], &seg); 233 234 if (new->addr + new->size > seg.addr && 235 new->addr < seg.addr + seg.size) { 236 aspeed_smc_error("new segment CS%d [ 0x%" 237 HWADDR_PRIx" - 0x%"HWADDR_PRIx" ] overlaps with " 238 "CS%d [ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]", 239 cs, new->addr, new->addr + new->size, 240 i, seg.addr, seg.addr + seg.size); 241 return true; 242 } 243 } 244 return false; 245} 246 247static void aspeed_smc_flash_set_segment_region(AspeedSMCState *s, int cs, 248 uint64_t regval) 249{ 250 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 251 AspeedSMCFlash *fl = &s->flashes[cs]; 252 AspeedSegments seg; 253 254 asc->reg_to_segment(s, regval, &seg); 255 256 memory_region_transaction_begin(); 257 memory_region_set_size(&fl->mmio, seg.size); 258 memory_region_set_address(&fl->mmio, seg.addr - asc->flash_window_base); 259 memory_region_set_enabled(&fl->mmio, !!seg.size); 260 memory_region_transaction_commit(); 261 262 s->regs[R_SEG_ADDR0 + cs] = regval; 263} 264 265static void aspeed_smc_flash_set_segment(AspeedSMCState *s, int cs, 266 uint64_t new) 267{ 268 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 269 AspeedSegments seg; 270 271 asc->reg_to_segment(s, new, &seg); 272 273 trace_aspeed_smc_flash_set_segment(cs, new, seg.addr, seg.addr + seg.size); 274 275 /* The start address of CS0 is read-only */ 276 if (cs == 0 && seg.addr != asc->flash_window_base) { 277 aspeed_smc_error("Tried to change CS0 start address to 0x%" 278 HWADDR_PRIx, seg.addr); 279 seg.addr = asc->flash_window_base; 280 new = asc->segment_to_reg(s, &seg); 281 } 282 283 /* 284 * The end address of the AST2500 spi controllers is also 285 * read-only. 286 */ 287 if ((asc->segments == aspeed_2500_spi1_segments || 288 asc->segments == aspeed_2500_spi2_segments) && 289 cs == asc->max_peripherals && 290 seg.addr + seg.size != asc->segments[cs].addr + 291 asc->segments[cs].size) { 292 aspeed_smc_error("Tried to change CS%d end address to 0x%" 293 HWADDR_PRIx, cs, seg.addr + seg.size); 294 seg.size = asc->segments[cs].addr + asc->segments[cs].size - 295 seg.addr; 296 new = asc->segment_to_reg(s, &seg); 297 } 298 299 /* Keep the segment in the overall flash window */ 300 if (seg.size && 301 (seg.addr + seg.size <= asc->flash_window_base || 302 seg.addr > asc->flash_window_base + asc->flash_window_size)) { 303 aspeed_smc_error("new segment for CS%d is invalid : " 304 "[ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]", 305 cs, seg.addr, seg.addr + seg.size); 306 return; 307 } 308 309 /* Check start address vs. alignment */ 310 if (seg.size && !QEMU_IS_ALIGNED(seg.addr, seg.size)) { 311 aspeed_smc_error("new segment for CS%d is not " 312 "aligned : [ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]", 313 cs, seg.addr, seg.addr + seg.size); 314 } 315 316 /* And segments should not overlap (in the specs) */ 317 aspeed_smc_flash_overlap(s, &seg, cs); 318 319 /* All should be fine now to move the region */ 320 aspeed_smc_flash_set_segment_region(s, cs, new); 321} 322 323static uint64_t aspeed_smc_flash_default_read(void *opaque, hwaddr addr, 324 unsigned size) 325{ 326 aspeed_smc_error("To 0x%" HWADDR_PRIx " of size %u" PRIx64, addr, size); 327 return 0; 328} 329 330static void aspeed_smc_flash_default_write(void *opaque, hwaddr addr, 331 uint64_t data, unsigned size) 332{ 333 aspeed_smc_error("To 0x%" HWADDR_PRIx " of size %u: 0x%" PRIx64, 334 addr, size, data); 335} 336 337static const MemoryRegionOps aspeed_smc_flash_default_ops = { 338 .read = aspeed_smc_flash_default_read, 339 .write = aspeed_smc_flash_default_write, 340 .endianness = DEVICE_LITTLE_ENDIAN, 341 .valid = { 342 .min_access_size = 1, 343 .max_access_size = 4, 344 }, 345}; 346 347static inline int aspeed_smc_flash_mode(const AspeedSMCFlash *fl) 348{ 349 const AspeedSMCState *s = fl->controller; 350 351 return s->regs[s->r_ctrl0 + fl->cs] & CTRL_CMD_MODE_MASK; 352} 353 354static inline bool aspeed_smc_is_writable(const AspeedSMCFlash *fl) 355{ 356 const AspeedSMCState *s = fl->controller; 357 358 return s->regs[s->r_conf] & (1 << (s->conf_enable_w0 + fl->cs)); 359} 360 361static inline int aspeed_smc_flash_cmd(const AspeedSMCFlash *fl) 362{ 363 const AspeedSMCState *s = fl->controller; 364 int cmd = (s->regs[s->r_ctrl0 + fl->cs] >> CTRL_CMD_SHIFT) & CTRL_CMD_MASK; 365 366 /* 367 * In read mode, the default SPI command is READ (0x3). In other 368 * modes, the command should necessarily be defined 369 * 370 * TODO: add support for READ4 (0x13) on AST2600 371 */ 372 if (aspeed_smc_flash_mode(fl) == CTRL_READMODE) { 373 cmd = SPI_OP_READ; 374 } 375 376 if (!cmd) { 377 aspeed_smc_error("no command defined for mode %d", 378 aspeed_smc_flash_mode(fl)); 379 } 380 381 return cmd; 382} 383 384static inline int aspeed_smc_flash_addr_width(const AspeedSMCFlash *fl) 385{ 386 const AspeedSMCState *s = fl->controller; 387 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 388 389 if (asc->addr_width) { 390 return asc->addr_width(s); 391 } else { 392 return s->regs[s->r_ce_ctrl] & (1 << (CTRL_EXTENDED0 + fl->cs)) ? 4 : 3; 393 } 394} 395 396static void aspeed_smc_flash_do_select(AspeedSMCFlash *fl, bool unselect) 397{ 398 AspeedSMCState *s = fl->controller; 399 400 trace_aspeed_smc_flash_select(fl->cs, unselect ? "un" : ""); 401 402 qemu_set_irq(s->cs_lines[fl->cs], unselect); 403} 404 405static void aspeed_smc_flash_select(AspeedSMCFlash *fl) 406{ 407 aspeed_smc_flash_do_select(fl, false); 408} 409 410static void aspeed_smc_flash_unselect(AspeedSMCFlash *fl) 411{ 412 aspeed_smc_flash_do_select(fl, true); 413} 414 415static uint32_t aspeed_smc_check_segment_addr(const AspeedSMCFlash *fl, 416 uint32_t addr) 417{ 418 const AspeedSMCState *s = fl->controller; 419 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 420 AspeedSegments seg; 421 422 asc->reg_to_segment(s, s->regs[R_SEG_ADDR0 + fl->cs], &seg); 423 if ((addr % seg.size) != addr) { 424 aspeed_smc_error("invalid address 0x%08x for CS%d segment : " 425 "[ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]", 426 addr, fl->cs, seg.addr, seg.addr + seg.size); 427 addr %= seg.size; 428 } 429 430 return addr; 431} 432 433static int aspeed_smc_flash_dummies(const AspeedSMCFlash *fl) 434{ 435 const AspeedSMCState *s = fl->controller; 436 uint32_t r_ctrl0 = s->regs[s->r_ctrl0 + fl->cs]; 437 uint32_t dummy_high = (r_ctrl0 >> CTRL_DUMMY_HIGH_SHIFT) & 0x1; 438 uint32_t dummy_low = (r_ctrl0 >> CTRL_DUMMY_LOW_SHIFT) & 0x3; 439 uint32_t dummies = ((dummy_high << 2) | dummy_low) * 8; 440 441 if (r_ctrl0 & CTRL_IO_DUAL_ADDR_DATA) { 442 dummies /= 2; 443 } 444 445 return dummies; 446} 447 448static void aspeed_smc_flash_setup(AspeedSMCFlash *fl, uint32_t addr) 449{ 450 const AspeedSMCState *s = fl->controller; 451 uint8_t cmd = aspeed_smc_flash_cmd(fl); 452 int i = aspeed_smc_flash_addr_width(fl); 453 454 /* Flash access can not exceed CS segment */ 455 addr = aspeed_smc_check_segment_addr(fl, addr); 456 457 ssi_transfer(s->spi, cmd); 458 while (i--) { 459 if (aspeed_smc_addr_byte_enabled(s, i)) { 460 ssi_transfer(s->spi, (addr >> (i * 8)) & 0xff); 461 } 462 } 463 464 /* 465 * Use fake transfers to model dummy bytes. The value should 466 * be configured to some non-zero value in fast read mode and 467 * zero in read mode. But, as the HW allows inconsistent 468 * settings, let's check for fast read mode. 469 */ 470 if (aspeed_smc_flash_mode(fl) == CTRL_FREADMODE) { 471 for (i = 0; i < aspeed_smc_flash_dummies(fl); i++) { 472 ssi_transfer(fl->controller->spi, s->regs[R_DUMMY_DATA] & 0xff); 473 } 474 } 475} 476 477static uint64_t aspeed_smc_flash_read(void *opaque, hwaddr addr, unsigned size) 478{ 479 AspeedSMCFlash *fl = opaque; 480 AspeedSMCState *s = fl->controller; 481 uint64_t ret = 0; 482 int i; 483 484 switch (aspeed_smc_flash_mode(fl)) { 485 case CTRL_USERMODE: 486 for (i = 0; i < size; i++) { 487 ret |= ssi_transfer(s->spi, 0x0) << (8 * i); 488 } 489 break; 490 case CTRL_READMODE: 491 case CTRL_FREADMODE: 492 aspeed_smc_flash_select(fl); 493 aspeed_smc_flash_setup(fl, addr); 494 495 for (i = 0; i < size; i++) { 496 ret |= ssi_transfer(s->spi, 0x0) << (8 * i); 497 } 498 499 aspeed_smc_flash_unselect(fl); 500 break; 501 default: 502 aspeed_smc_error("invalid flash mode %d", aspeed_smc_flash_mode(fl)); 503 } 504 505 trace_aspeed_smc_flash_read(fl->cs, addr, size, ret, 506 aspeed_smc_flash_mode(fl)); 507 return ret; 508} 509 510/* 511 * TODO (clg@kaod.org): stolen from xilinx_spips.c. Should move to a 512 * common include header. 513 */ 514typedef enum { 515 READ = 0x3, READ_4 = 0x13, 516 FAST_READ = 0xb, FAST_READ_4 = 0x0c, 517 DOR = 0x3b, DOR_4 = 0x3c, 518 QOR = 0x6b, QOR_4 = 0x6c, 519 DIOR = 0xbb, DIOR_4 = 0xbc, 520 QIOR = 0xeb, QIOR_4 = 0xec, 521 522 PP = 0x2, PP_4 = 0x12, 523 DPP = 0xa2, 524 QPP = 0x32, QPP_4 = 0x34, 525} FlashCMD; 526 527static int aspeed_smc_num_dummies(uint8_t command) 528{ 529 switch (command) { /* check for dummies */ 530 case READ: /* no dummy bytes/cycles */ 531 case PP: 532 case DPP: 533 case QPP: 534 case READ_4: 535 case PP_4: 536 case QPP_4: 537 return 0; 538 case FAST_READ: 539 case DOR: 540 case QOR: 541 case FAST_READ_4: 542 case DOR_4: 543 case QOR_4: 544 return 1; 545 case DIOR: 546 case DIOR_4: 547 return 2; 548 case QIOR: 549 case QIOR_4: 550 return 4; 551 default: 552 return -1; 553 } 554} 555 556static bool aspeed_smc_do_snoop(AspeedSMCFlash *fl, uint64_t data, 557 unsigned size) 558{ 559 AspeedSMCState *s = fl->controller; 560 uint8_t addr_width = aspeed_smc_flash_addr_width(fl); 561 562 trace_aspeed_smc_do_snoop(fl->cs, s->snoop_index, s->snoop_dummies, 563 (uint8_t) data & 0xff); 564 565 if (s->snoop_index == SNOOP_OFF) { 566 return false; /* Do nothing */ 567 568 } else if (s->snoop_index == SNOOP_START) { 569 uint8_t cmd = data & 0xff; 570 int ndummies = aspeed_smc_num_dummies(cmd); 571 572 /* 573 * No dummy cycles are expected with the current command. Turn 574 * off snooping and let the transfer proceed normally. 575 */ 576 if (ndummies <= 0) { 577 s->snoop_index = SNOOP_OFF; 578 return false; 579 } 580 581 s->snoop_dummies = ndummies * 8; 582 583 } else if (s->snoop_index >= addr_width + 1) { 584 585 /* The SPI transfer has reached the dummy cycles sequence */ 586 for (; s->snoop_dummies; s->snoop_dummies--) { 587 ssi_transfer(s->spi, s->regs[R_DUMMY_DATA] & 0xff); 588 } 589 590 /* If no more dummy cycles are expected, turn off snooping */ 591 if (!s->snoop_dummies) { 592 s->snoop_index = SNOOP_OFF; 593 } else { 594 s->snoop_index += size; 595 } 596 597 /* 598 * Dummy cycles have been faked already. Ignore the current 599 * SPI transfer 600 */ 601 return true; 602 } 603 604 s->snoop_index += size; 605 return false; 606} 607 608static void aspeed_smc_flash_write(void *opaque, hwaddr addr, uint64_t data, 609 unsigned size) 610{ 611 AspeedSMCFlash *fl = opaque; 612 AspeedSMCState *s = fl->controller; 613 int i; 614 615 trace_aspeed_smc_flash_write(fl->cs, addr, size, data, 616 aspeed_smc_flash_mode(fl)); 617 618 if (!aspeed_smc_is_writable(fl)) { 619 aspeed_smc_error("flash is not writable at 0x%" HWADDR_PRIx, addr); 620 return; 621 } 622 623 switch (aspeed_smc_flash_mode(fl)) { 624 case CTRL_USERMODE: 625 if (aspeed_smc_do_snoop(fl, data, size)) { 626 break; 627 } 628 629 for (i = 0; i < size; i++) { 630 ssi_transfer(s->spi, (data >> (8 * i)) & 0xff); 631 } 632 break; 633 case CTRL_WRITEMODE: 634 aspeed_smc_flash_select(fl); 635 aspeed_smc_flash_setup(fl, addr); 636 637 for (i = 0; i < size; i++) { 638 ssi_transfer(s->spi, (data >> (8 * i)) & 0xff); 639 } 640 641 aspeed_smc_flash_unselect(fl); 642 break; 643 default: 644 aspeed_smc_error("invalid flash mode %d", aspeed_smc_flash_mode(fl)); 645 } 646} 647 648static const MemoryRegionOps aspeed_smc_flash_ops = { 649 .read = aspeed_smc_flash_read, 650 .write = aspeed_smc_flash_write, 651 .endianness = DEVICE_LITTLE_ENDIAN, 652 .valid = { 653 .min_access_size = 1, 654 .max_access_size = 4, 655 }, 656}; 657 658static void aspeed_smc_flash_update_ctrl(AspeedSMCFlash *fl, uint32_t value) 659{ 660 AspeedSMCState *s = fl->controller; 661 bool unselect; 662 663 /* User mode selects the CS, other modes unselect */ 664 unselect = (value & CTRL_CMD_MODE_MASK) != CTRL_USERMODE; 665 666 /* A change of CTRL_CE_STOP_ACTIVE from 0 to 1, unselects the CS */ 667 if (!(s->regs[s->r_ctrl0 + fl->cs] & CTRL_CE_STOP_ACTIVE) && 668 value & CTRL_CE_STOP_ACTIVE) { 669 unselect = true; 670 } 671 672 s->regs[s->r_ctrl0 + fl->cs] = value; 673 674 s->snoop_index = unselect ? SNOOP_OFF : SNOOP_START; 675 676 aspeed_smc_flash_do_select(fl, unselect); 677} 678 679static void aspeed_smc_reset(DeviceState *d) 680{ 681 AspeedSMCState *s = ASPEED_SMC(d); 682 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 683 int i; 684 685 if (asc->resets) { 686 memcpy(s->regs, asc->resets, sizeof s->regs); 687 } else { 688 memset(s->regs, 0, sizeof s->regs); 689 } 690 691 /* Unselect all peripherals */ 692 for (i = 0; i < s->num_cs; ++i) { 693 s->regs[s->r_ctrl0 + i] |= CTRL_CE_STOP_ACTIVE; 694 qemu_set_irq(s->cs_lines[i], true); 695 } 696 697 /* setup the default segment register values and regions for all */ 698 for (i = 0; i < asc->max_peripherals; ++i) { 699 aspeed_smc_flash_set_segment_region(s, i, 700 asc->segment_to_reg(s, &asc->segments[i])); 701 } 702 703 s->snoop_index = SNOOP_OFF; 704 s->snoop_dummies = 0; 705} 706 707static uint64_t aspeed_smc_read(void *opaque, hwaddr addr, unsigned int size) 708{ 709 AspeedSMCState *s = ASPEED_SMC(opaque); 710 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(opaque); 711 712 addr >>= 2; 713 714 if (addr == s->r_conf || 715 (addr >= s->r_timings && 716 addr < s->r_timings + asc->nregs_timings) || 717 addr == s->r_ce_ctrl || 718 addr == R_CE_CMD_CTRL || 719 addr == R_INTR_CTRL || 720 addr == R_DUMMY_DATA || 721 (aspeed_smc_has_wdt_control(asc) && addr == R_FMC_WDT2_CTRL) || 722 (aspeed_smc_has_dma(asc) && addr == R_DMA_CTRL) || 723 (aspeed_smc_has_dma(asc) && addr == R_DMA_FLASH_ADDR) || 724 (aspeed_smc_has_dma(asc) && addr == R_DMA_DRAM_ADDR) || 725 (aspeed_smc_has_dma(asc) && addr == R_DMA_LEN) || 726 (aspeed_smc_has_dma(asc) && addr == R_DMA_CHECKSUM) || 727 (addr >= R_SEG_ADDR0 && 728 addr < R_SEG_ADDR0 + asc->max_peripherals) || 729 (addr >= s->r_ctrl0 && addr < s->r_ctrl0 + asc->max_peripherals)) { 730 731 trace_aspeed_smc_read(addr << 2, size, s->regs[addr]); 732 733 return s->regs[addr]; 734 } else { 735 qemu_log_mask(LOG_UNIMP, "%s: not implemented: 0x%" HWADDR_PRIx "\n", 736 __func__, addr); 737 return -1; 738 } 739} 740 741static uint8_t aspeed_smc_hclk_divisor(uint8_t hclk_mask) 742{ 743 /* HCLK/1 .. HCLK/16 */ 744 const uint8_t hclk_divisors[] = { 745 15, 7, 14, 6, 13, 5, 12, 4, 11, 3, 10, 2, 9, 1, 8, 0 746 }; 747 int i; 748 749 for (i = 0; i < ARRAY_SIZE(hclk_divisors); i++) { 750 if (hclk_mask == hclk_divisors[i]) { 751 return i + 1; 752 } 753 } 754 755 aspeed_smc_error("invalid HCLK mask %x", hclk_mask); 756 return 0; 757} 758 759/* 760 * When doing calibration, the SPI clock rate in the CE0 Control 761 * Register and the read delay cycles in the Read Timing Compensation 762 * Register are set using bit[11:4] of the DMA Control Register. 763 */ 764static void aspeed_smc_dma_calibration(AspeedSMCState *s) 765{ 766 uint8_t delay = 767 (s->regs[R_DMA_CTRL] >> DMA_CTRL_DELAY_SHIFT) & DMA_CTRL_DELAY_MASK; 768 uint8_t hclk_mask = 769 (s->regs[R_DMA_CTRL] >> DMA_CTRL_FREQ_SHIFT) & DMA_CTRL_FREQ_MASK; 770 uint8_t hclk_div = aspeed_smc_hclk_divisor(hclk_mask); 771 uint32_t hclk_shift = (hclk_div - 1) << 2; 772 uint8_t cs; 773 774 /* 775 * The Read Timing Compensation Register values apply to all CS on 776 * the SPI bus and only HCLK/1 - HCLK/5 can have tunable delays 777 */ 778 if (hclk_div && hclk_div < 6) { 779 s->regs[s->r_timings] &= ~(0xf << hclk_shift); 780 s->regs[s->r_timings] |= delay << hclk_shift; 781 } 782 783 /* 784 * TODO: compute the CS from the DMA address and the segment 785 * registers. This is not really a problem for now because the 786 * Timing Register values apply to all CS and software uses CS0 to 787 * do calibration. 788 */ 789 cs = 0; 790 s->regs[s->r_ctrl0 + cs] &= 791 ~(CE_CTRL_CLOCK_FREQ_MASK << CE_CTRL_CLOCK_FREQ_SHIFT); 792 s->regs[s->r_ctrl0 + cs] |= CE_CTRL_CLOCK_FREQ(hclk_div); 793} 794 795/* 796 * Emulate read errors in the DMA Checksum Register for high 797 * frequencies and optimistic settings of the Read Timing Compensation 798 * Register. This will help in tuning the SPI timing calibration 799 * algorithm. 800 */ 801static bool aspeed_smc_inject_read_failure(AspeedSMCState *s) 802{ 803 uint8_t delay = 804 (s->regs[R_DMA_CTRL] >> DMA_CTRL_DELAY_SHIFT) & DMA_CTRL_DELAY_MASK; 805 uint8_t hclk_mask = 806 (s->regs[R_DMA_CTRL] >> DMA_CTRL_FREQ_SHIFT) & DMA_CTRL_FREQ_MASK; 807 808 /* 809 * Typical values of a palmetto-bmc machine. 810 */ 811 switch (aspeed_smc_hclk_divisor(hclk_mask)) { 812 case 4 ... 16: 813 return false; 814 case 3: /* at least one HCLK cycle delay */ 815 return (delay & 0x7) < 1; 816 case 2: /* at least two HCLK cycle delay */ 817 return (delay & 0x7) < 2; 818 case 1: /* (> 100MHz) is above the max freq of the controller */ 819 return true; 820 default: 821 g_assert_not_reached(); 822 } 823} 824 825/* 826 * Accumulate the result of the reads to provide a checksum that will 827 * be used to validate the read timing settings. 828 */ 829static void aspeed_smc_dma_checksum(AspeedSMCState *s) 830{ 831 MemTxResult result; 832 uint32_t data; 833 834 if (s->regs[R_DMA_CTRL] & DMA_CTRL_WRITE) { 835 aspeed_smc_error("invalid direction for DMA checksum"); 836 return; 837 } 838 839 if (s->regs[R_DMA_CTRL] & DMA_CTRL_CALIB) { 840 aspeed_smc_dma_calibration(s); 841 } 842 843 while (s->regs[R_DMA_LEN]) { 844 data = address_space_ldl_le(&s->flash_as, s->regs[R_DMA_FLASH_ADDR], 845 MEMTXATTRS_UNSPECIFIED, &result); 846 if (result != MEMTX_OK) { 847 aspeed_smc_error("Flash read failed @%08x", 848 s->regs[R_DMA_FLASH_ADDR]); 849 return; 850 } 851 trace_aspeed_smc_dma_checksum(s->regs[R_DMA_FLASH_ADDR], data); 852 853 /* 854 * When the DMA is on-going, the DMA registers are updated 855 * with the current working addresses and length. 856 */ 857 s->regs[R_DMA_CHECKSUM] += data; 858 s->regs[R_DMA_FLASH_ADDR] += 4; 859 s->regs[R_DMA_LEN] -= 4; 860 } 861 862 if (s->inject_failure && aspeed_smc_inject_read_failure(s)) { 863 s->regs[R_DMA_CHECKSUM] = 0xbadc0de; 864 } 865 866} 867 868static void aspeed_smc_dma_rw(AspeedSMCState *s) 869{ 870 MemTxResult result; 871 uint32_t data; 872 873 trace_aspeed_smc_dma_rw(s->regs[R_DMA_CTRL] & DMA_CTRL_WRITE ? 874 "write" : "read", 875 s->regs[R_DMA_FLASH_ADDR], 876 s->regs[R_DMA_DRAM_ADDR], 877 s->regs[R_DMA_LEN]); 878 while (s->regs[R_DMA_LEN]) { 879 if (s->regs[R_DMA_CTRL] & DMA_CTRL_WRITE) { 880 data = address_space_ldl_le(&s->dram_as, s->regs[R_DMA_DRAM_ADDR], 881 MEMTXATTRS_UNSPECIFIED, &result); 882 if (result != MEMTX_OK) { 883 aspeed_smc_error("DRAM read failed @%08x", 884 s->regs[R_DMA_DRAM_ADDR]); 885 return; 886 } 887 888 address_space_stl_le(&s->flash_as, s->regs[R_DMA_FLASH_ADDR], 889 data, MEMTXATTRS_UNSPECIFIED, &result); 890 if (result != MEMTX_OK) { 891 aspeed_smc_error("Flash write failed @%08x", 892 s->regs[R_DMA_FLASH_ADDR]); 893 return; 894 } 895 } else { 896 data = address_space_ldl_le(&s->flash_as, s->regs[R_DMA_FLASH_ADDR], 897 MEMTXATTRS_UNSPECIFIED, &result); 898 if (result != MEMTX_OK) { 899 aspeed_smc_error("Flash read failed @%08x", 900 s->regs[R_DMA_FLASH_ADDR]); 901 return; 902 } 903 904 address_space_stl_le(&s->dram_as, s->regs[R_DMA_DRAM_ADDR], 905 data, MEMTXATTRS_UNSPECIFIED, &result); 906 if (result != MEMTX_OK) { 907 aspeed_smc_error("DRAM write failed @%08x", 908 s->regs[R_DMA_DRAM_ADDR]); 909 return; 910 } 911 } 912 913 /* 914 * When the DMA is on-going, the DMA registers are updated 915 * with the current working addresses and length. 916 */ 917 s->regs[R_DMA_FLASH_ADDR] += 4; 918 s->regs[R_DMA_DRAM_ADDR] += 4; 919 s->regs[R_DMA_LEN] -= 4; 920 s->regs[R_DMA_CHECKSUM] += data; 921 } 922} 923 924static void aspeed_smc_dma_stop(AspeedSMCState *s) 925{ 926 /* 927 * When the DMA is disabled, INTR_CTRL_DMA_STATUS=0 means the 928 * engine is idle 929 */ 930 s->regs[R_INTR_CTRL] &= ~INTR_CTRL_DMA_STATUS; 931 s->regs[R_DMA_CHECKSUM] = 0; 932 933 /* 934 * Lower the DMA irq in any case. The IRQ control register could 935 * have been cleared before disabling the DMA. 936 */ 937 qemu_irq_lower(s->irq); 938} 939 940/* 941 * When INTR_CTRL_DMA_STATUS=1, the DMA has completed and a new DMA 942 * can start even if the result of the previous was not collected. 943 */ 944static bool aspeed_smc_dma_in_progress(AspeedSMCState *s) 945{ 946 return s->regs[R_DMA_CTRL] & DMA_CTRL_ENABLE && 947 !(s->regs[R_INTR_CTRL] & INTR_CTRL_DMA_STATUS); 948} 949 950static void aspeed_smc_dma_done(AspeedSMCState *s) 951{ 952 s->regs[R_INTR_CTRL] |= INTR_CTRL_DMA_STATUS; 953 if (s->regs[R_INTR_CTRL] & INTR_CTRL_DMA_EN) { 954 qemu_irq_raise(s->irq); 955 } 956} 957 958static void aspeed_smc_dma_ctrl(AspeedSMCState *s, uint32_t dma_ctrl) 959{ 960 if (!(dma_ctrl & DMA_CTRL_ENABLE)) { 961 s->regs[R_DMA_CTRL] = dma_ctrl; 962 963 aspeed_smc_dma_stop(s); 964 return; 965 } 966 967 if (aspeed_smc_dma_in_progress(s)) { 968 aspeed_smc_error("DMA in progress !"); 969 return; 970 } 971 972 s->regs[R_DMA_CTRL] = dma_ctrl; 973 974 if (s->regs[R_DMA_CTRL] & DMA_CTRL_CKSUM) { 975 aspeed_smc_dma_checksum(s); 976 } else { 977 aspeed_smc_dma_rw(s); 978 } 979 980 aspeed_smc_dma_done(s); 981} 982 983static inline bool aspeed_smc_dma_granted(AspeedSMCState *s) 984{ 985 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 986 987 if (!(asc->features & ASPEED_SMC_FEATURE_DMA_GRANT)) { 988 return true; 989 } 990 991 if (!(s->regs[R_DMA_CTRL] & DMA_CTRL_GRANT)) { 992 aspeed_smc_error("DMA not granted"); 993 return false; 994 } 995 996 return true; 997} 998 999static void aspeed_2600_smc_dma_ctrl(AspeedSMCState *s, uint32_t dma_ctrl) 1000{ 1001 /* Preserve DMA bits */ 1002 dma_ctrl |= s->regs[R_DMA_CTRL] & (DMA_CTRL_REQUEST | DMA_CTRL_GRANT); 1003 1004 if (dma_ctrl == 0xAEED0000) { 1005 /* automatically grant request */ 1006 s->regs[R_DMA_CTRL] |= (DMA_CTRL_REQUEST | DMA_CTRL_GRANT); 1007 return; 1008 } 1009 1010 /* clear request */ 1011 if (dma_ctrl == 0xDEEA0000) { 1012 s->regs[R_DMA_CTRL] &= ~(DMA_CTRL_REQUEST | DMA_CTRL_GRANT); 1013 return; 1014 } 1015 1016 if (!aspeed_smc_dma_granted(s)) { 1017 aspeed_smc_error("DMA not granted"); 1018 return; 1019 } 1020 1021 aspeed_smc_dma_ctrl(s, dma_ctrl); 1022 s->regs[R_DMA_CTRL] &= ~(DMA_CTRL_REQUEST | DMA_CTRL_GRANT); 1023} 1024 1025static void aspeed_smc_write(void *opaque, hwaddr addr, uint64_t data, 1026 unsigned int size) 1027{ 1028 AspeedSMCState *s = ASPEED_SMC(opaque); 1029 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 1030 uint32_t value = data; 1031 1032 trace_aspeed_smc_write(addr, size, data); 1033 1034 addr >>= 2; 1035 1036 if (addr == s->r_conf || 1037 (addr >= s->r_timings && 1038 addr < s->r_timings + asc->nregs_timings) || 1039 addr == s->r_ce_ctrl) { 1040 s->regs[addr] = value; 1041 } else if (addr >= s->r_ctrl0 && addr < s->r_ctrl0 + s->num_cs) { 1042 int cs = addr - s->r_ctrl0; 1043 aspeed_smc_flash_update_ctrl(&s->flashes[cs], value); 1044 } else if (addr >= R_SEG_ADDR0 && 1045 addr < R_SEG_ADDR0 + asc->max_peripherals) { 1046 int cs = addr - R_SEG_ADDR0; 1047 1048 if (value != s->regs[R_SEG_ADDR0 + cs]) { 1049 aspeed_smc_flash_set_segment(s, cs, value); 1050 } 1051 } else if (addr == R_CE_CMD_CTRL) { 1052 s->regs[addr] = value & 0xff; 1053 } else if (addr == R_DUMMY_DATA) { 1054 s->regs[addr] = value & 0xff; 1055 } else if (aspeed_smc_has_wdt_control(asc) && addr == R_FMC_WDT2_CTRL) { 1056 s->regs[addr] = value & FMC_WDT2_CTRL_EN; 1057 } else if (addr == R_INTR_CTRL) { 1058 s->regs[addr] = value; 1059 } else if (aspeed_smc_has_dma(asc) && addr == R_DMA_CTRL) { 1060 asc->dma_ctrl(s, value); 1061 } else if (aspeed_smc_has_dma(asc) && addr == R_DMA_DRAM_ADDR && 1062 aspeed_smc_dma_granted(s)) { 1063 s->regs[addr] = DMA_DRAM_ADDR(asc, value); 1064 } else if (aspeed_smc_has_dma(asc) && addr == R_DMA_FLASH_ADDR && 1065 aspeed_smc_dma_granted(s)) { 1066 s->regs[addr] = DMA_FLASH_ADDR(asc, value); 1067 } else if (aspeed_smc_has_dma(asc) && addr == R_DMA_LEN && 1068 aspeed_smc_dma_granted(s)) { 1069 s->regs[addr] = DMA_LENGTH(value); 1070 } else { 1071 qemu_log_mask(LOG_UNIMP, "%s: not implemented: 0x%" HWADDR_PRIx "\n", 1072 __func__, addr); 1073 return; 1074 } 1075} 1076 1077static const MemoryRegionOps aspeed_smc_ops = { 1078 .read = aspeed_smc_read, 1079 .write = aspeed_smc_write, 1080 .endianness = DEVICE_LITTLE_ENDIAN, 1081}; 1082 1083static void aspeed_smc_instance_init(Object *obj) 1084{ 1085 AspeedSMCState *s = ASPEED_SMC(obj); 1086 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 1087 int i; 1088 1089 for (i = 0; i < asc->max_peripherals; i++) { 1090 object_initialize_child(obj, "flash[*]", &s->flashes[i], 1091 TYPE_ASPEED_SMC_FLASH); 1092 } 1093} 1094 1095/* 1096 * Initialize the custom address spaces for DMAs 1097 */ 1098static void aspeed_smc_dma_setup(AspeedSMCState *s, Error **errp) 1099{ 1100 if (!s->dram_mr) { 1101 error_setg(errp, TYPE_ASPEED_SMC ": 'dram' link not set"); 1102 return; 1103 } 1104 1105 address_space_init(&s->flash_as, &s->mmio_flash, 1106 TYPE_ASPEED_SMC ".dma-flash"); 1107 address_space_init(&s->dram_as, s->dram_mr, 1108 TYPE_ASPEED_SMC ".dma-dram"); 1109} 1110 1111static void aspeed_smc_realize(DeviceState *dev, Error **errp) 1112{ 1113 SysBusDevice *sbd = SYS_BUS_DEVICE(dev); 1114 AspeedSMCState *s = ASPEED_SMC(dev); 1115 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 1116 int i; 1117 hwaddr offset = 0; 1118 1119 /* keep a copy under AspeedSMCState to speed up accesses */ 1120 s->r_conf = asc->r_conf; 1121 s->r_ce_ctrl = asc->r_ce_ctrl; 1122 s->r_ctrl0 = asc->r_ctrl0; 1123 s->r_timings = asc->r_timings; 1124 s->conf_enable_w0 = asc->conf_enable_w0; 1125 1126 /* Enforce some real HW limits */ 1127 if (s->num_cs > asc->max_peripherals) { 1128 aspeed_smc_error("num_cs cannot exceed: %d", asc->max_peripherals); 1129 s->num_cs = asc->max_peripherals; 1130 } 1131 1132 /* DMA irq. Keep it first for the initialization in the SoC */ 1133 sysbus_init_irq(sbd, &s->irq); 1134 1135 s->spi = ssi_create_bus(dev, "spi"); 1136 1137 /* Setup cs_lines for peripherals */ 1138 s->cs_lines = g_new0(qemu_irq, s->num_cs); 1139 1140 for (i = 0; i < s->num_cs; ++i) { 1141 sysbus_init_irq(sbd, &s->cs_lines[i]); 1142 } 1143 1144 /* The memory region for the controller registers */ 1145 memory_region_init_io(&s->mmio, OBJECT(s), &aspeed_smc_ops, s, 1146 TYPE_ASPEED_SMC, asc->nregs * 4); 1147 sysbus_init_mmio(sbd, &s->mmio); 1148 1149 /* 1150 * The container memory region representing the address space 1151 * window in which the flash modules are mapped. The size and 1152 * address depends on the SoC model and controller type. 1153 */ 1154 memory_region_init_io(&s->mmio_flash, OBJECT(s), 1155 &aspeed_smc_flash_default_ops, s, 1156 TYPE_ASPEED_SMC ".flash", 1157 asc->flash_window_size); 1158 memory_region_init_alias(&s->mmio_flash_alias, OBJECT(s), 1159 TYPE_ASPEED_SMC ".flash", 1160 &s->mmio_flash, 0, asc->flash_window_size); 1161 sysbus_init_mmio(sbd, &s->mmio_flash_alias); 1162 1163 /* 1164 * Let's create a sub memory region for each possible peripheral. All 1165 * have a configurable memory segment in the overall flash mapping 1166 * window of the controller but, there is not necessarily a flash 1167 * module behind to handle the memory accesses. This depends on 1168 * the board configuration. 1169 */ 1170 for (i = 0; i < asc->max_peripherals; ++i) { 1171 AspeedSMCFlash *fl = &s->flashes[i]; 1172 1173 if (!object_property_set_link(OBJECT(fl), "controller", OBJECT(s), 1174 errp)) { 1175 return; 1176 } 1177 if (!object_property_set_uint(OBJECT(fl), "cs", i, errp)) { 1178 return; 1179 } 1180 if (!sysbus_realize(SYS_BUS_DEVICE(fl), errp)) { 1181 return; 1182 } 1183 1184 memory_region_add_subregion(&s->mmio_flash, offset, &fl->mmio); 1185 offset += asc->segments[i].size; 1186 } 1187 1188 /* DMA support */ 1189 if (aspeed_smc_has_dma(asc)) { 1190 aspeed_smc_dma_setup(s, errp); 1191 } 1192} 1193 1194static const VMStateDescription vmstate_aspeed_smc = { 1195 .name = "aspeed.smc", 1196 .version_id = 2, 1197 .minimum_version_id = 2, 1198 .fields = (VMStateField[]) { 1199 VMSTATE_UINT32_ARRAY(regs, AspeedSMCState, ASPEED_SMC_R_MAX), 1200 VMSTATE_UINT8(snoop_index, AspeedSMCState), 1201 VMSTATE_UINT8(snoop_dummies, AspeedSMCState), 1202 VMSTATE_END_OF_LIST() 1203 } 1204}; 1205 1206static Property aspeed_smc_properties[] = { 1207 DEFINE_PROP_UINT32("num-cs", AspeedSMCState, num_cs, 1), 1208 DEFINE_PROP_BOOL("inject-failure", AspeedSMCState, inject_failure, false), 1209 DEFINE_PROP_LINK("dram", AspeedSMCState, dram_mr, 1210 TYPE_MEMORY_REGION, MemoryRegion *), 1211 DEFINE_PROP_END_OF_LIST(), 1212}; 1213 1214static void aspeed_smc_class_init(ObjectClass *klass, void *data) 1215{ 1216 DeviceClass *dc = DEVICE_CLASS(klass); 1217 1218 dc->realize = aspeed_smc_realize; 1219 dc->reset = aspeed_smc_reset; 1220 device_class_set_props(dc, aspeed_smc_properties); 1221 dc->vmsd = &vmstate_aspeed_smc; 1222} 1223 1224static const TypeInfo aspeed_smc_info = { 1225 .name = TYPE_ASPEED_SMC, 1226 .parent = TYPE_SYS_BUS_DEVICE, 1227 .instance_init = aspeed_smc_instance_init, 1228 .instance_size = sizeof(AspeedSMCState), 1229 .class_size = sizeof(AspeedSMCClass), 1230 .class_init = aspeed_smc_class_init, 1231 .abstract = true, 1232}; 1233 1234static void aspeed_smc_flash_realize(DeviceState *dev, Error **errp) 1235{ 1236 AspeedSMCFlash *s = ASPEED_SMC_FLASH(dev); 1237 AspeedSMCClass *asc; 1238 g_autofree char *name = g_strdup_printf(TYPE_ASPEED_SMC_FLASH ".%d", s->cs); 1239 1240 if (!s->controller) { 1241 error_setg(errp, TYPE_ASPEED_SMC_FLASH ": 'controller' link not set"); 1242 return; 1243 } 1244 1245 asc = ASPEED_SMC_GET_CLASS(s->controller); 1246 1247 /* 1248 * Use the default segment value to size the memory region. This 1249 * can be changed by FW at runtime. 1250 */ 1251 memory_region_init_io(&s->mmio, OBJECT(s), &aspeed_smc_flash_ops, 1252 s, name, asc->segments[s->cs].size); 1253 sysbus_init_mmio(SYS_BUS_DEVICE(dev), &s->mmio); 1254} 1255 1256static Property aspeed_smc_flash_properties[] = { 1257 DEFINE_PROP_UINT8("cs", AspeedSMCFlash, cs, 0), 1258 DEFINE_PROP_LINK("controller", AspeedSMCFlash, controller, TYPE_ASPEED_SMC, 1259 AspeedSMCState *), 1260 DEFINE_PROP_END_OF_LIST(), 1261}; 1262 1263static void aspeed_smc_flash_class_init(ObjectClass *klass, void *data) 1264{ 1265 DeviceClass *dc = DEVICE_CLASS(klass); 1266 1267 dc->desc = "Aspeed SMC Flash device region"; 1268 dc->realize = aspeed_smc_flash_realize; 1269 device_class_set_props(dc, aspeed_smc_flash_properties); 1270} 1271 1272static const TypeInfo aspeed_smc_flash_info = { 1273 .name = TYPE_ASPEED_SMC_FLASH, 1274 .parent = TYPE_SYS_BUS_DEVICE, 1275 .instance_size = sizeof(AspeedSMCFlash), 1276 .class_init = aspeed_smc_flash_class_init, 1277}; 1278 1279/* 1280 * The Segment Registers of the AST2400 and AST2500 have a 8MB 1281 * unit. The address range of a flash SPI peripheral is encoded with 1282 * absolute addresses which should be part of the overall controller 1283 * window. 1284 */ 1285static uint32_t aspeed_smc_segment_to_reg(const AspeedSMCState *s, 1286 const AspeedSegments *seg) 1287{ 1288 uint32_t reg = 0; 1289 reg |= ((seg->addr >> 23) & SEG_START_MASK) << SEG_START_SHIFT; 1290 reg |= (((seg->addr + seg->size) >> 23) & SEG_END_MASK) << SEG_END_SHIFT; 1291 return reg; 1292} 1293 1294static void aspeed_smc_reg_to_segment(const AspeedSMCState *s, 1295 uint32_t reg, AspeedSegments *seg) 1296{ 1297 seg->addr = ((reg >> SEG_START_SHIFT) & SEG_START_MASK) << 23; 1298 seg->size = (((reg >> SEG_END_SHIFT) & SEG_END_MASK) << 23) - seg->addr; 1299} 1300 1301static const AspeedSegments aspeed_2400_smc_segments[] = { 1302 { 0x10000000, 32 * MiB }, 1303}; 1304 1305static void aspeed_2400_smc_class_init(ObjectClass *klass, void *data) 1306{ 1307 DeviceClass *dc = DEVICE_CLASS(klass); 1308 AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass); 1309 1310 dc->desc = "Aspeed 2400 SMC Controller"; 1311 asc->r_conf = R_CONF; 1312 asc->r_ce_ctrl = R_CE_CTRL; 1313 asc->r_ctrl0 = R_CTRL0; 1314 asc->r_timings = R_TIMINGS; 1315 asc->nregs_timings = 1; 1316 asc->conf_enable_w0 = CONF_ENABLE_W0; 1317 asc->max_peripherals = 1; 1318 asc->segments = aspeed_2400_smc_segments; 1319 asc->flash_window_base = 0x10000000; 1320 asc->flash_window_size = 0x6000000; 1321 asc->features = 0x0; 1322 asc->nregs = ASPEED_SMC_R_SMC_MAX; 1323 asc->segment_to_reg = aspeed_smc_segment_to_reg; 1324 asc->reg_to_segment = aspeed_smc_reg_to_segment; 1325 asc->dma_ctrl = aspeed_smc_dma_ctrl; 1326} 1327 1328static const TypeInfo aspeed_2400_smc_info = { 1329 .name = "aspeed.smc-ast2400", 1330 .parent = TYPE_ASPEED_SMC, 1331 .class_init = aspeed_2400_smc_class_init, 1332}; 1333 1334static const uint32_t aspeed_2400_fmc_resets[ASPEED_SMC_R_MAX] = { 1335 /* 1336 * CE0 and CE1 types are HW strapped in SCU70. Do it here to 1337 * simplify the model. 1338 */ 1339 [R_CONF] = CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0, 1340}; 1341 1342static const AspeedSegments aspeed_2400_fmc_segments[] = { 1343 { 0x20000000, 64 * MiB }, /* start address is readonly */ 1344 { 0x24000000, 32 * MiB }, 1345 { 0x26000000, 32 * MiB }, 1346 { 0x28000000, 32 * MiB }, 1347 { 0x2A000000, 32 * MiB } 1348}; 1349 1350static void aspeed_2400_fmc_class_init(ObjectClass *klass, void *data) 1351{ 1352 DeviceClass *dc = DEVICE_CLASS(klass); 1353 AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass); 1354 1355 dc->desc = "Aspeed 2400 FMC Controller"; 1356 asc->r_conf = R_CONF; 1357 asc->r_ce_ctrl = R_CE_CTRL; 1358 asc->r_ctrl0 = R_CTRL0; 1359 asc->r_timings = R_TIMINGS; 1360 asc->nregs_timings = 1; 1361 asc->conf_enable_w0 = CONF_ENABLE_W0; 1362 asc->max_peripherals = 5; 1363 asc->segments = aspeed_2400_fmc_segments; 1364 asc->resets = aspeed_2400_fmc_resets; 1365 asc->flash_window_base = 0x20000000; 1366 asc->flash_window_size = 0x10000000; 1367 asc->features = ASPEED_SMC_FEATURE_DMA; 1368 asc->dma_flash_mask = 0x0FFFFFFC; 1369 asc->dma_dram_mask = 0x1FFFFFFC; 1370 asc->nregs = ASPEED_SMC_R_MAX; 1371 asc->segment_to_reg = aspeed_smc_segment_to_reg; 1372 asc->reg_to_segment = aspeed_smc_reg_to_segment; 1373 asc->dma_ctrl = aspeed_smc_dma_ctrl; 1374} 1375 1376static const TypeInfo aspeed_2400_fmc_info = { 1377 .name = "aspeed.fmc-ast2400", 1378 .parent = TYPE_ASPEED_SMC, 1379 .class_init = aspeed_2400_fmc_class_init, 1380}; 1381 1382static const AspeedSegments aspeed_2400_spi1_segments[] = { 1383 { 0x30000000, 64 * MiB }, 1384}; 1385 1386static int aspeed_2400_spi1_addr_width(const AspeedSMCState *s) 1387{ 1388 return s->regs[R_SPI_CTRL0] & CTRL_AST2400_SPI_4BYTE ? 4 : 3; 1389} 1390 1391static void aspeed_2400_spi1_class_init(ObjectClass *klass, void *data) 1392{ 1393 DeviceClass *dc = DEVICE_CLASS(klass); 1394 AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass); 1395 1396 dc->desc = "Aspeed 2400 SPI1 Controller"; 1397 asc->r_conf = R_SPI_CONF; 1398 asc->r_ce_ctrl = 0xff; 1399 asc->r_ctrl0 = R_SPI_CTRL0; 1400 asc->r_timings = R_SPI_TIMINGS; 1401 asc->nregs_timings = 1; 1402 asc->conf_enable_w0 = SPI_CONF_ENABLE_W0; 1403 asc->max_peripherals = 1; 1404 asc->segments = aspeed_2400_spi1_segments; 1405 asc->flash_window_base = 0x30000000; 1406 asc->flash_window_size = 0x10000000; 1407 asc->features = 0x0; 1408 asc->nregs = ASPEED_SMC_R_SPI_MAX; 1409 asc->segment_to_reg = aspeed_smc_segment_to_reg; 1410 asc->reg_to_segment = aspeed_smc_reg_to_segment; 1411 asc->dma_ctrl = aspeed_smc_dma_ctrl; 1412 asc->addr_width = aspeed_2400_spi1_addr_width; 1413} 1414 1415static const TypeInfo aspeed_2400_spi1_info = { 1416 .name = "aspeed.spi1-ast2400", 1417 .parent = TYPE_ASPEED_SMC, 1418 .class_init = aspeed_2400_spi1_class_init, 1419}; 1420 1421static const uint32_t aspeed_2500_fmc_resets[ASPEED_SMC_R_MAX] = { 1422 [R_CONF] = (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0 | 1423 CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE1), 1424}; 1425 1426static const AspeedSegments aspeed_2500_fmc_segments[] = { 1427 { 0x20000000, 128 * MiB }, /* start address is readonly */ 1428 { 0x28000000, 32 * MiB }, 1429 { 0x2A000000, 32 * MiB }, 1430}; 1431 1432static void aspeed_2500_fmc_class_init(ObjectClass *klass, void *data) 1433{ 1434 DeviceClass *dc = DEVICE_CLASS(klass); 1435 AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass); 1436 1437 dc->desc = "Aspeed 2600 FMC Controller"; 1438 asc->r_conf = R_CONF; 1439 asc->r_ce_ctrl = R_CE_CTRL; 1440 asc->r_ctrl0 = R_CTRL0; 1441 asc->r_timings = R_TIMINGS; 1442 asc->nregs_timings = 1; 1443 asc->conf_enable_w0 = CONF_ENABLE_W0; 1444 asc->max_peripherals = 3; 1445 asc->segments = aspeed_2500_fmc_segments; 1446 asc->resets = aspeed_2500_fmc_resets; 1447 asc->flash_window_base = 0x20000000; 1448 asc->flash_window_size = 0x10000000; 1449 asc->features = ASPEED_SMC_FEATURE_DMA; 1450 asc->dma_flash_mask = 0x0FFFFFFC; 1451 asc->dma_dram_mask = 0x3FFFFFFC; 1452 asc->nregs = ASPEED_SMC_R_MAX; 1453 asc->segment_to_reg = aspeed_smc_segment_to_reg; 1454 asc->reg_to_segment = aspeed_smc_reg_to_segment; 1455 asc->dma_ctrl = aspeed_smc_dma_ctrl; 1456} 1457 1458static const TypeInfo aspeed_2500_fmc_info = { 1459 .name = "aspeed.fmc-ast2500", 1460 .parent = TYPE_ASPEED_SMC, 1461 .class_init = aspeed_2500_fmc_class_init, 1462}; 1463 1464static const AspeedSegments aspeed_2500_spi1_segments[] = { 1465 { 0x30000000, 32 * MiB }, /* start address is readonly */ 1466 { 0x32000000, 96 * MiB }, /* end address is readonly */ 1467}; 1468 1469static void aspeed_2500_spi1_class_init(ObjectClass *klass, void *data) 1470{ 1471 DeviceClass *dc = DEVICE_CLASS(klass); 1472 AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass); 1473 1474 dc->desc = "Aspeed 2600 SPI1 Controller"; 1475 asc->r_conf = R_CONF; 1476 asc->r_ce_ctrl = R_CE_CTRL; 1477 asc->r_ctrl0 = R_CTRL0; 1478 asc->r_timings = R_TIMINGS; 1479 asc->nregs_timings = 1; 1480 asc->conf_enable_w0 = CONF_ENABLE_W0; 1481 asc->max_peripherals = 2; 1482 asc->segments = aspeed_2500_spi1_segments; 1483 asc->flash_window_base = 0x30000000; 1484 asc->flash_window_size = 0x8000000; 1485 asc->features = 0x0; 1486 asc->nregs = ASPEED_SMC_R_MAX; 1487 asc->segment_to_reg = aspeed_smc_segment_to_reg; 1488 asc->reg_to_segment = aspeed_smc_reg_to_segment; 1489 asc->dma_ctrl = aspeed_smc_dma_ctrl; 1490} 1491 1492static const TypeInfo aspeed_2500_spi1_info = { 1493 .name = "aspeed.spi1-ast2500", 1494 .parent = TYPE_ASPEED_SMC, 1495 .class_init = aspeed_2500_spi1_class_init, 1496}; 1497 1498static const AspeedSegments aspeed_2500_spi2_segments[] = { 1499 { 0x38000000, 32 * MiB }, /* start address is readonly */ 1500 { 0x3A000000, 96 * MiB }, /* end address is readonly */ 1501}; 1502 1503static void aspeed_2500_spi2_class_init(ObjectClass *klass, void *data) 1504{ 1505 DeviceClass *dc = DEVICE_CLASS(klass); 1506 AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass); 1507 1508 dc->desc = "Aspeed 2600 SPI2 Controller"; 1509 asc->r_conf = R_CONF; 1510 asc->r_ce_ctrl = R_CE_CTRL; 1511 asc->r_ctrl0 = R_CTRL0; 1512 asc->r_timings = R_TIMINGS; 1513 asc->nregs_timings = 1; 1514 asc->conf_enable_w0 = CONF_ENABLE_W0; 1515 asc->max_peripherals = 2; 1516 asc->segments = aspeed_2500_spi2_segments; 1517 asc->flash_window_base = 0x38000000; 1518 asc->flash_window_size = 0x8000000; 1519 asc->features = 0x0; 1520 asc->nregs = ASPEED_SMC_R_MAX; 1521 asc->segment_to_reg = aspeed_smc_segment_to_reg; 1522 asc->reg_to_segment = aspeed_smc_reg_to_segment; 1523 asc->dma_ctrl = aspeed_smc_dma_ctrl; 1524} 1525 1526static const TypeInfo aspeed_2500_spi2_info = { 1527 .name = "aspeed.spi2-ast2500", 1528 .parent = TYPE_ASPEED_SMC, 1529 .class_init = aspeed_2500_spi2_class_init, 1530}; 1531 1532/* 1533 * The Segment Registers of the AST2600 have a 1MB unit. The address 1534 * range of a flash SPI peripheral is encoded with offsets in the overall 1535 * controller window. The previous SoC AST2400 and AST2500 used 1536 * absolute addresses. Only bits [27:20] are relevant and the end 1537 * address is an upper bound limit. 1538 */ 1539#define AST2600_SEG_ADDR_MASK 0x0ff00000 1540 1541static uint32_t aspeed_2600_smc_segment_to_reg(const AspeedSMCState *s, 1542 const AspeedSegments *seg) 1543{ 1544 uint32_t reg = 0; 1545 1546 /* Disabled segments have a nil register */ 1547 if (!seg->size) { 1548 return 0; 1549 } 1550 1551 reg |= (seg->addr & AST2600_SEG_ADDR_MASK) >> 16; /* start offset */ 1552 reg |= (seg->addr + seg->size - 1) & AST2600_SEG_ADDR_MASK; /* end offset */ 1553 return reg; 1554} 1555 1556static void aspeed_2600_smc_reg_to_segment(const AspeedSMCState *s, 1557 uint32_t reg, AspeedSegments *seg) 1558{ 1559 uint32_t start_offset = (reg << 16) & AST2600_SEG_ADDR_MASK; 1560 uint32_t end_offset = reg & AST2600_SEG_ADDR_MASK; 1561 AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s); 1562 1563 if (reg) { 1564 seg->addr = asc->flash_window_base + start_offset; 1565 seg->size = end_offset + MiB - start_offset; 1566 } else { 1567 seg->addr = asc->flash_window_base; 1568 seg->size = 0; 1569 } 1570} 1571 1572static const uint32_t aspeed_2600_fmc_resets[ASPEED_SMC_R_MAX] = { 1573 [R_CONF] = (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0 | 1574 CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE1 | 1575 CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE2), 1576}; 1577 1578static const AspeedSegments aspeed_2600_fmc_segments[] = { 1579 { 0x0, 128 * MiB }, /* start address is readonly */ 1580 { 128 * MiB, 128 * MiB }, /* default is disabled but needed for -kernel */ 1581 { 0x0, 0 }, /* disabled */ 1582}; 1583 1584static void aspeed_2600_fmc_class_init(ObjectClass *klass, void *data) 1585{ 1586 DeviceClass *dc = DEVICE_CLASS(klass); 1587 AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass); 1588 1589 dc->desc = "Aspeed 2600 FMC Controller"; 1590 asc->r_conf = R_CONF; 1591 asc->r_ce_ctrl = R_CE_CTRL; 1592 asc->r_ctrl0 = R_CTRL0; 1593 asc->r_timings = R_TIMINGS; 1594 asc->nregs_timings = 1; 1595 asc->conf_enable_w0 = CONF_ENABLE_W0; 1596 asc->max_peripherals = 3; 1597 asc->segments = aspeed_2600_fmc_segments; 1598 asc->resets = aspeed_2600_fmc_resets; 1599 asc->flash_window_base = 0x20000000; 1600 asc->flash_window_size = 0x10000000; 1601 asc->features = ASPEED_SMC_FEATURE_DMA | 1602 ASPEED_SMC_FEATURE_WDT_CONTROL; 1603 asc->dma_flash_mask = 0x0FFFFFFC; 1604 asc->dma_dram_mask = 0x3FFFFFFC; 1605 asc->nregs = ASPEED_SMC_R_MAX; 1606 asc->segment_to_reg = aspeed_2600_smc_segment_to_reg; 1607 asc->reg_to_segment = aspeed_2600_smc_reg_to_segment; 1608 asc->dma_ctrl = aspeed_2600_smc_dma_ctrl; 1609} 1610 1611static const TypeInfo aspeed_2600_fmc_info = { 1612 .name = "aspeed.fmc-ast2600", 1613 .parent = TYPE_ASPEED_SMC, 1614 .class_init = aspeed_2600_fmc_class_init, 1615}; 1616 1617static const AspeedSegments aspeed_2600_spi1_segments[] = { 1618 { 0x0, 128 * MiB }, /* start address is readonly */ 1619 { 0x0, 0 }, /* disabled */ 1620}; 1621 1622static void aspeed_2600_spi1_class_init(ObjectClass *klass, void *data) 1623{ 1624 DeviceClass *dc = DEVICE_CLASS(klass); 1625 AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass); 1626 1627 dc->desc = "Aspeed 2600 SPI1 Controller"; 1628 asc->r_conf = R_CONF; 1629 asc->r_ce_ctrl = R_CE_CTRL; 1630 asc->r_ctrl0 = R_CTRL0; 1631 asc->r_timings = R_TIMINGS; 1632 asc->nregs_timings = 2; 1633 asc->conf_enable_w0 = CONF_ENABLE_W0; 1634 asc->max_peripherals = 2; 1635 asc->segments = aspeed_2600_spi1_segments; 1636 asc->flash_window_base = 0x30000000; 1637 asc->flash_window_size = 0x10000000; 1638 asc->features = ASPEED_SMC_FEATURE_DMA | 1639 ASPEED_SMC_FEATURE_DMA_GRANT; 1640 asc->dma_flash_mask = 0x0FFFFFFC; 1641 asc->dma_dram_mask = 0x3FFFFFFC; 1642 asc->nregs = ASPEED_SMC_R_MAX; 1643 asc->segment_to_reg = aspeed_2600_smc_segment_to_reg; 1644 asc->reg_to_segment = aspeed_2600_smc_reg_to_segment; 1645 asc->dma_ctrl = aspeed_2600_smc_dma_ctrl; 1646} 1647 1648static const TypeInfo aspeed_2600_spi1_info = { 1649 .name = "aspeed.spi1-ast2600", 1650 .parent = TYPE_ASPEED_SMC, 1651 .class_init = aspeed_2600_spi1_class_init, 1652}; 1653 1654static const AspeedSegments aspeed_2600_spi2_segments[] = { 1655 { 0x0, 128 * MiB }, /* start address is readonly */ 1656 { 0x0, 0 }, /* disabled */ 1657 { 0x0, 0 }, /* disabled */ 1658}; 1659 1660static void aspeed_2600_spi2_class_init(ObjectClass *klass, void *data) 1661{ 1662 DeviceClass *dc = DEVICE_CLASS(klass); 1663 AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass); 1664 1665 dc->desc = "Aspeed 2600 SPI2 Controller"; 1666 asc->r_conf = R_CONF; 1667 asc->r_ce_ctrl = R_CE_CTRL; 1668 asc->r_ctrl0 = R_CTRL0; 1669 asc->r_timings = R_TIMINGS; 1670 asc->nregs_timings = 3; 1671 asc->conf_enable_w0 = CONF_ENABLE_W0; 1672 asc->max_peripherals = 3; 1673 asc->segments = aspeed_2600_spi2_segments; 1674 asc->flash_window_base = 0x50000000; 1675 asc->flash_window_size = 0x10000000; 1676 asc->features = ASPEED_SMC_FEATURE_DMA | 1677 ASPEED_SMC_FEATURE_DMA_GRANT; 1678 asc->dma_flash_mask = 0x0FFFFFFC; 1679 asc->dma_dram_mask = 0x3FFFFFFC; 1680 asc->nregs = ASPEED_SMC_R_MAX; 1681 asc->segment_to_reg = aspeed_2600_smc_segment_to_reg; 1682 asc->reg_to_segment = aspeed_2600_smc_reg_to_segment; 1683 asc->dma_ctrl = aspeed_2600_smc_dma_ctrl; 1684} 1685 1686static const TypeInfo aspeed_2600_spi2_info = { 1687 .name = "aspeed.spi2-ast2600", 1688 .parent = TYPE_ASPEED_SMC, 1689 .class_init = aspeed_2600_spi2_class_init, 1690}; 1691 1692static void aspeed_smc_register_types(void) 1693{ 1694 type_register_static(&aspeed_smc_flash_info); 1695 type_register_static(&aspeed_smc_info); 1696 type_register_static(&aspeed_2400_smc_info); 1697 type_register_static(&aspeed_2400_fmc_info); 1698 type_register_static(&aspeed_2400_spi1_info); 1699 type_register_static(&aspeed_2500_fmc_info); 1700 type_register_static(&aspeed_2500_spi1_info); 1701 type_register_static(&aspeed_2500_spi2_info); 1702 type_register_static(&aspeed_2600_fmc_info); 1703 type_register_static(&aspeed_2600_spi1_info); 1704 type_register_static(&aspeed_2600_spi2_info); 1705} 1706 1707type_init(aspeed_smc_register_types)